Search Documents

By Martin JD, McNicol JH

The electrolytic zinc plant at Port Pirie South Australia, was designed and constructed to treat zinc oxide fume recovered by treatment of lead blast furnace slag in two fuming furnaces, The plant was commissioned in late 1967. The equipment installed and the oper- ating procedures adopted,'are described in some detail.

Jan 1, 1975

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

Before any accident prevention and total safety programme can succeed, a safety concientiousness or attitude needs to be implanted in the employees' minds. Psycholog- ical and physiological conditions play a vital role in accident causation and prevention. Both need attention in a good safety programme, but working place conditions and environment are more easily corrected. However, the challenge is to change attitudes in the minds of men - psychological factors in accidents. To do this does not require a Safety Officer, but does require a Safety Adviser. At Blackwater mine a Safety Adviser is available to all sections of the organisation to guide and assist, to provide data and material to use at meetings, to help in accident investi- gations and to help organise training. To eventually achieve total commitment requires every member of the management team to be a salesman towards all around selling an attitude to safe working, a way of life. At Blackwater mine the workforce is young overall with most employees being under 40 years old. Psychologically this is a quite different problem to a balanced ages working group. A great deal of effort is needed to communicate with the younger, articulate, better educated employee who is also generally a skilled operator in the capital intensive

Jan 1, 1975

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

On Wednesday 11th November, 1970, a series of violent explosions occur-- red within No.1 Basic Oxygen Steelmak- ing (B.O.S.) furnace at the Whyalla Works of the Broken Hill Proprietary Co. Ltd., (B.H.P.) when the furnace was moved immediately prior to tapping. Water from a burnt out flux chute had flooded the bath while the furnace was tilted slightly towards the tapping side waiting to tap. Although no one was injured, dam- age in excess of $54 000 was caused to the hood and superstructure. The water hydrated the burnt dolomite refractory lining some of which sub- sequently collapsed exposing bare fur- nace shell over part of the cone.

Jan 1, 1975

Japanese pig iron production in 1973 registered about 90 million tons. As clearly seen from the productivity (2.04 t/m3/D), and fuel ratio (494 kg/t-pig), the Japanese steel industry has maintained quite high levels of efficiency in blast-furnace (BF) operations. Among the many factors which have contributed toward these high levels of efficiency, the use of high quality coke is very important. The Japanese steel industry imports about 85% of its metallurgical coals from various countries of the world, including Australia. The effective use of these metallurgical coals of various origins in accordance with their re- spective properties is most essential for maintaining coke quality. This paper describes coking properties of various metallurgical coals and blending techniques based on these coking properties, in relation to the specifications of coke quality required for efficient BF operations. This paper also describes briefly new technology for expanding the scope of the use of coking coals.

Jan 1, 1975

By Flierman GA, Van Toor CH

Investigations were carried out of burden distribution using a full scale model of the furnace top. Various charging sequences were used and large differences were found between ore charged as sinter-pellets and as pellets-sinter. These were attributed to the differences in the angle of repose between the two materials. Permeability index was defined which was independent of the driving rate from which a furnace resistance index was obtained for use in weekly reports. Results are summarised as a single expression between blast rates and pressures and the values of Qbl and Qmax are continuously measured to aid the operators in controlling the wind rate in the safe AP region. Results also indicate a reserve in capacity of No. 7 BF.

Jan 1, 1975

A considerable amount of psychological research has been conducted on human behaviour and its relationship to accidents. However, the research covers very wide fields and the findings drawn are so varied that at first sight they are confusing and there does not appear to be any major useful lead. I propose a discussion of a number of research findings to illustrate the variety and complexity of the human behaviour factors involved in considering safety. Such discuss- ion might point to some conclusions which could lead to an action programme to improve safety records.

Jan 1, 1975

In recent decades the awareness of environmental issues by the general public has developed at an accelerat- ing rate. This is the result of a number of factors including more scientific knowledge of environments and of the impacts of modern society upon them, higher levels of education, the opportunity for people to travel more, and the success of the various communication media in bringing in- formation to the communities of the world about such environmental crises or threats as the smogs of Los Angeles and London, the Torrey Canyon and Santa Barbara oilspills, Minamata disease in Japan, the spread of the Crown of Thorns starfish, the disposal of toxic industrial wastes into the Upper Rhine, the discovery of high mercury and zinc contents in marine foods in southern Australian waters, and the proposal to mine limestone at Precipitous Bluff in Tasmania.

Jan 1, 1975

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975

By Mercer JK

This paper gives a description of the research undertaken by an explosives manufacturer to give better technical advice to the Mineral Industry. Blasting Physics is defined as giving a systematic and coherent account of the initiation and subsequent effects of high explosives upon the surrounding medium. As a result of this work a mathematical model based on the gener- ally accepted mechanism of blasting has been developed. The mechanism and the resulting model are briefly outlined. IFrom'this model the effects of burden, spacing, blasthole diameter, rock and explosive properties upon fragmentation and heave can be calculated. Using these calculations it is then possible to see how variations in frag Imentation and heave can affect the overall production costs of a mine whether it is surface or underground. The overall costs are made up of a number of individual costs - drilling, blasting, loading, hauling and crushing. ach of these operations influences or is influenced by fragmentation and heave s these costs are inter-related, the

Jan 1, 1975

By Savage E. N

The porphyry copper minerals of Melanesia occur within a host of narrow veinlets in predominantly quartz diorite stocks or as contact metasomatic masses in skarns adjacent to the intrusion. Some 90 per cent of the constituent minerals comprise pyrite or marcasite, chalcopyrite, and magnetite with the remainder mainly bornite and hematite with accessory rutile and chalcocite together with several trace minerals. Gold is found mainly as inclusions in chalcopyrite, and minor molybdenite occurs likewise.Of particular significance is the persistent occurrence of accessory rutile of hydrothermal origin intimately intergrown with chalcopyrite. The rutile occurs relatively late in the hydrothermal sequence and upon weathering of the deposit may be released on a cumulative basis possibly in sufficient amounts to constitute a particulate pathfinder mineral which may aid in prospecting.Rutile is present in all the Melanesian occurrences studied and is also prominent in several American deposits.The porphyry copper mineralogy is characterized by the presence of accessory hydrothermal rutile intergrown with chalcopyrite.

Jan 1, 1975

Marketing of mineral products has not yet succumbed to the degree of pre- dictability and exactitude that is fam- iliar to the engineer or metallurgist in pursuing their profession. Whilst the Great Market of the world economy dic- tates circumstances for the sale of min- eral products, there are more than just buyers and sellers in the determination of the revenue received by the producer. For the engineer or metallurgist he will be required to gain an understanding of these participants and of the peculiar languages of the market place. This will be only one of his tasks in learn- ing to communicate with society, as his responsibilities increase as he climbs the ladder of success. There is un- doubtedly a need for better statistical information so that producers and sell- ers can make an appropriate and earlier response to market conditions. There is in addition, a need for more aggressive concern by raw material producers for the development and promotion of better end use of their products. Undoubtedly the marketing of mineral products will be more influenced by the direct involv- ment of government agencies than has been the case in the past. Whilst that 1. Director - Marketing & Finance, North Broken Hill Limited.

Jan 1, 1975

By Propster M, Choudhry M

THIS note gives comments on the paper by Kitaev et al on p. 68 of this book and compares results with those obtained by ourselves. We wish to say that the authors are to be congratulated on their sophisticated approach to an important problem and that it complements our efforts on flow maldistribution.1-5 It is our view that Eqs. (1)-(5) on p. 69 are impressive, but unfortunately with present day computers and computational facilities, it would be quite impractical to contemplate the numerical solution of these. Eq. (8) in the authors' paper, on p. 70, does provide the logical starting point for tackling flow maldistribution problems and strictly speaking this equation is more accurate than Eq. (1) in our paper in this book. We note in passing that there is direct experimental evidence to support the contention that our Eq. (1) is at least a reasonable approximation and one may question in a practical sense whether the refinement afforded by Eq. (8) in the paper by Kitaev et a/ is justified. While one must readily accept the appropriateness of Eq. (8) of Kitaev et al as a starting point, the subsequent mathematical manipulation by the authors is open to serious criticism. In order to solve this complex, non-linear equation Kitaev et al postulated irrotational flow, which afforded considerable simplification. One can argue simply on physical grounds that the assumption of irrotational flow is inappropriate, a fact which should be readily apparent on inspection of the flow fields shown in Figs. 2 and 3 of Kitaev's paper. It follows that while the starting point through the use of Eq. (8) is correct the results derived from this starting point may be suspect because of the erroneous nature of the irrotational flow assumption.

Jan 1, 1975

Zircon is extensively used as moulding sand in the production of steel and high-duty iron castings. To achieve a satisfactory grade of zircon concentrate, the zircon particles may need ,to have surface coatings removed, as such coatings can hinder electrostatic and magnetic separation of zircon from associated minerals. Xn addition the presence of surface coatings on the zircon. particles can cause sinterins and fusion of the zircon to the east metal resulting in "burnt-on" sand or fritting of the casting. "Burnon" necessitates cleaning of the casting by grinding or chipping, which is expensive and results in loss of definition on the casting face.Hudson (1966) has pointed out ,that some coatings on mineral sands are lightly-adhering clays which can be removed quite readily by agitating the sands in water for a few minutes-thus their removal constitutesno problem. However, the heavy gingery coloured coating which adheres strongly to the surface of the particles in some deposits, and which has generally been considered to be a form of iron oxide (Baker, 1962; Hudson, 1966), cannot be removed effectively by attrition cleaning in water (Hudson, 1966). Such coatings limit the usefulness of these concentrates in the foundry industry.An investigation of strongly-adhering coatings on "ginger zircon" concentrates from the Yoganup deposit of Westralian Sands Ltd has shown that the stain consists of a cemented mixtvre of hydrated iron and aluminium oxides and kaolin minerals, and that it can be removed by a relatively low cost treatment.IDENTIFICATION OF THE STAIN BY XRDX-ray powder diffraction (XRD) patterns were obtained from small samples of stain scraped, individually, from the surface of hand-picked zircon and ilmenite crystals. These scrapings were mounted on quartz fibres and exposed to CoKa radiation in a 57 mm Debye camera. To avoid heavy fogging of the x-ray films, a substantial amount of the iron oxides was preferentially leached from the scrapings (before mounting) with an ammonium oxalate-oxalic acid solution (Rooksby, 1961). The residual material gave a fairly well resolved powder pattern (Table 1). A...

Jan 1, 1975

By Hyslop W

It is shown that coke has a major influence on the pattern of operation and on the aerodynamics of the blast furnace and that the physical and chemical characteristics of coke, at each stage in the furnace, determine its ability to satisfy requirements for iron production and coke economy. Analysis of coke sampled from operating furnaces is compared with furnace behaviour. The available data suggests the importance of segregation, strength, size change and chemical degradation of coke on furnace performance. Correlations are presented for coke breakdown ratio as a function of coke rate and hearth diameter which shows that breakdown increases with hearth diameter and with decreasing coke rate. It is also shown that the Micum tests do not reflect the coke strength in a predictable way and that solution reactions appear to play an important role in giving rise to a pitting effect on the cell walls of the coke with the resultant deterioration in coke properties. The catalytic effect of activating substances, such as alkalis, is noted and results are presented which show the effect of carbon solution on the coke strength. The importance of coke in the stack and in the bosh is discussed and flooding results are presented for BSC furnaces which show the probable driving limits for the furnaces considered. It is also shown that coke sampled from different tuyeres in a furnace gives quite different flooding limits. Other applications of the coke test work at BSC are also noted and the relevant objectives listed.

Jan 1, 1975

The recent installation of top gas temperature probes in blast furnaces at Australian Iron & Steel Pty. Ltd. - Port Kembla, has provided the means for studying radial gas flow distribution in blast furnace shafts. This paper describes the top gas temperature probes and outlines their development and results of initial studies aimed at obtaining a suitable relationships between temperature profiles and furnace parameters. The effects of various combinations of burden materials have been outlined by the results reported. The use of probes has also helped to clarify the effect of casting cycles on furnace operation leading to increased emphasis on the reduction of the interval between gun-up and drill-out. Areas for future studies are also broadly Outlined.

Jan 1, 1975

The basic model for the evaluation of any coal-bearing property is the cash flow projection, the major components of which are operating costs, capital charges, taxation and revenue. A range of cash flow projections can be produced by varying the assumptions which underlie the operating costs, by assuming various forms of capital funding, by making assumptions as to future taxation and by speculating upon the present and future market value of the product. As for any model, the informational inputs and assumptions are vital because, no matter how sophisticated the processing, the informational inputs and assumptions cannot be improved by it. That is to say, the validity of the output (the total evaluation itself) cannot be of greater certainty or significance than that of the inputs. The total evaluation can of course be expressed in a number of ways such as the Discounted Cash Flow (D.C.F.) Rate of Return, the Net Present Value or, the Payback Period. The foregoing statement may seem trite. However, it is necessary to be clear about it so as to avoid unnecessary complication and a preoccupation with techniques as opposed to the informational inputs and assumptions. So far as techniques are concerned, much has been written and said about them during the last decade. Most of us have heard, if not always understood, something about probabilistic models, Monte Carlo simulation, sensitivity and risk analysis to say nothing of inflationary costing and the relative merits of developing cash flows in terms of current or constant money. Those techniques have their value, particularly if they can serve to illuminate conclusions which could not be reached on a simple and even perhaps on an intuitive basis. I am, however, reminded of one major coal mining project in which 20 or more major variables were identified, many cash flow projections were run on the computer and a detailed sensitivity analysis was carried out. The major conclusion reached was that the D.C.F. Rate of Return was predominantly sensitive to variations in selling price and operating cost. Of course, the funding and fiscal elements of a cash flow projection have to be dealt with as rigorously as possible. However, in the development of any coal property, capital requirements and taxation are, in part at any rate, dependent upon the assumed operational parameters. If the latter are misjudged, the whole evaluation process is deeply affected. The same is true of revenue, in the sense that, the positive cash flow is a function of output as well as selling price and again, misjudgements about achievable and maintainable levels of production also deeply affect the final evaluation. I shall try to underline the fundamental influence of the technological factors upon lead times, capital costs, operating costs, taxation, funding and the achievable and maintainable levels of production. In turn, these affect the whole question of coal property evaluation and indeed, the likely success or failure of any coal mining venture. I make no apology therefore that this paper does not set out to discuss the more esoteric aspects of the evaluation process but rather, directs attention towards some of the informational inputs and assumptions which merit clarification and discussion.

Jan 1, 1975

By Petersen V, Potke W, Polthier K

The paper reviews some of the aerodynamic factors in the blast furnace process and outlines the areas requiring further study. Detailed discussion is given to the pressure drop in both the dry and the wet zone of the furnace and an optimum coke size is suggested for minimum pressure drop. The effect of various charging sequences on the distribution of the gas in the furnace shaft is treated and notes on stack injection included. Flow phenomena limiting blast furnace output and the influence of aerodynamics on the movement of the bed in the furnace are outlined and these include fluidisation, flooding and raceway formation. A mention is made of alkalis, sulphur, zinc, softening, and oil injection and the mixed effect in blast furnace economics of increased tuyere velocity as problems requiring further research.

Jan 1, 1975

By Atalla YM

Steel rolling mill product finishing pro cesses gradually become or often already are unsuited for current production and marketing conditions. Indications are made as to what has been done to (i) rectify situations of this kind and, (ii) to reduce both product finishing time and costs. The principal features of two separate case studies are reviewed, these being (a) the finishing-end of B.H.P.'s Newcastle o.2 Merchant Mill and, (b) a mixed functions finishing yard and warehouses group (known as he Merchant Mills Loading Yard) which has been perating for a number of years. The areas in ach case are identified as a system while the arious functions, principal product streams nd processing equipment are respectively iden- ified as sub-systems and system elements. etails are given of the models used in each Sub-system dependency on the system as a le is traced by means of an information and ision analysis or by time studies and the sonableness of the system elements is deter- ed by computer programming or by simple com- ison methods. The-accumulated data is used derive improved mill finishing-end or Load Yard,functioning concepts according to pro- rules whilst at the same time considering

Jan 1, 1975