Search Documents

By Redman P. G, McMahon B. K

A simple technique for evaluating the field stress ratio is presented, based on the results of extensometer or convergence tape measure- ments taken in an advancing tunnel. This tech- nique also yields a value for the rock mass modulus, provided Poisson's Ratio is assumed. The results of two case studies are presented illustrating the effectiveness of the method.

Jan 1, 1981

By H Kurth, L Balzan

On-belt analysers have been used since the early 1980s in the coal sector to measure ash content in real time for diverting material on conveyors to remove waste, bypass beneficiation and allow suitable material to proceed to the wash plant for processing. Since 2008, a GEOSCAN-M elemental analyser has been used on an overland conveyor in South Africa to divert direct-shipping quality iron ore to bypass a jig plant. This paper focusses on recent evaluation work to determine the suitability of an on-belt analyser to upgrade the processing plant feed in a copper-gold operation.Copper-gold ore samples from New Gold’s New Afton Mine near Kamloops, BC, Canada were tested to assess measurement accuracy over short time increments. A two-minute measurement increment has been used in the minerals sector as a compromise between good measurement accuracy and a useful tonnage (haul truck equivalent size or smaller). At New Afton, this increment represents approximately 35 t of material. Segregation decisions are currently made after visual and sometimes analytical determination, at increments of approximately 500 t to designate material as ore or waste at the drawbell in the cave.Results of test work including the composition range and expected accuracies by element are shown. The operation, which is not mine constrained, was evaluating the potential for ore upgrading through waste and low grade increment diversion to upgrade ore quality feeding the mill. Prompt-gamma neutron activation analysis (PGNAA) was considered as the company recognised that it would measure through the full conveyed cross section continuously and produce multi-elemental measurements unaffected by particle size, dust, moisture content, layering and segregation, mineralogy and belt speed.GEOSCAN analyses over various analysis periods will be collected to identify variability in the conveyed material quality and used to generate tonnage-grade curves so that an optimal diversion (bulk sorting) tonnage increment can be determined. Measurement increment time can be customised to suit site requirements. CITATION:Kurth, H and Balzan, L, 2017. Assessing bulk sorting suitability at the New Afton mine, in Proceedings MetPlant 2017, pp 315–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By M Ljunggren, M Lundh

Dissolved air flotation (DAF) in wastewater treatment as a separation process of submillimetre biological flocs is based on the generation of bubble/floc aggregates. DAF is a complex process but has got advantages, such as allowing a high hydraulic load, compared to sedimentation. A thorough knowledge of the physics of the DAF process is, however, still lacking. This paper will present results of experimental studies on three aspects of significance to the separation process û the flow structure in the flotation tank, rise velocities of aggregates, influence of floc size on the separation efficiency. Flow structure. Measurements were performed in a pilot plant mapping and visualising the velocity field. The dispersion water (bubbles) had a decisive influence on the flow structure due to the effect of the bubbles on the bulk water density. Stratified conditions with a less dense, bubble-containing upper layer and a clear water, denser bottom layer were important for a good separation. A simple model of the stratified flow structure was elaborated making it possible to interpret the function of the aggregate rise velocities. Bubble/floc aggregates. The dynamics of single flocs, bubbles, aggregates were visualised using a borescope + CCD video camera + digital recorder + image analysis. Sequences of video frames made it possible to determine the rise velocities of the single aggregates. These velocities were found to be in the range 1 - 9 mm/s with a tendency for large flocs to have higher rise velocities. Separation versus floc size. The floc size distribution was measured in the DAF process. Data from three different DAF cases showed, that large flocs (> about 100 ¦m) were entirely separated, whereas small flocs experienced a less good separation. It was, moreover, found, that a very significant separation of flocs took place in the very upstream end of the separation zone in a pilot plant case.

Jan 1, 2005

FOR some years after the erection of the first chlorination plant at Mount Morgan the ore sent to the works for treatment was mined entirely from the oxidized zone; consequently, the bullion recovered at the refinery was of unusual purity, averaging about 972 in fineness, and, as no impurity in any way detrimental to the softness or toughness of the bullion was present, there was no necessity to subject it to any refining process.The charcoal from the filters was calcined to ash in small reverberatory furnaces of the usual type. The ash was mixed with suitable proportions of soda and borax to form a good liquid slag. This' mixture was then charged into salamander cruciblesand run to metal and slag in the ordinary wind furnaces-a slow and tedious proceeding in the Mount Morgan climate. The bullion, cleaned of slag, was re-melted under borax and poured into bars weighing from 350 to 400 oz.; these bars, after being dipped while hot into dilute sulphuric acid, were packed and sent to the mint. Of late years, however, the ore coming from the deeper ground of the oxidized zone became much lower in gold values, and contained variable but increasing quantities of sulphides, sulphates...

Jan 1, 1911

By H Cifuentes, D J. Williams

Despite the recognised importance of tailings management, there remain little data on the potential benefits of biological treatments compared with physical and chemical treatments. The operation of the majority of tailings storage facilities (TSFs) continues to employ mainly physical solutions, such as sub-aerial tailings slurry deposition, with increasing adoption of thickening, paste and filtration to dewater the tailings involving the addition of chemicals such as flocculants and coagulants. However, with tailings production continuing to escalate rapidly due to the increasing demand for commodities and reducing ore grades, available technologies have not demonstrated cost-effective performance at high tailings production rates. This paper examines the emerging role of bacteria to better manage tailings, reducing risks and optimising storage capacity. Bacteria have the potential to enhance tailings dewatering, maintain their permeability, delay the onset of desiccation cracking, and improve their shear strength. Bacteria-treated tailings may be suitable for use as construction materials. Bacteria also have potential in limiting the dusting of tailings and facilitating rehabilitation on closure. The paper describes a series of laboratory involving the addition of harmless bacteria to a range of tailings. The bacteria form a compact material called calcite (a common and stable form of calcium carbonate), which immobilises the tailings particles, releases water, and cements the tailings in a stable and natural matrix. The water released can be recovered or evaporated, depending on site objectives. The bacterial reactions are linked to physical and chemical processes, providing the potential for an optimal mix of technologies for particular tailings and site conditions.CITATION:Cifuentes, H and Williams, D J, 2018. Potential improvement of tailings geotechnical behaviour using bacteria, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 228–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By E Thomas, L McCallum, G Dale, J Bennett, K Reardon-Smith, S Raine

Sustainable closure of coal mines in Australia to a safe, stable, non-polluting condition remains one of the industry’s biggest environmental and social challenges. A significant proportion of mines in the Bowen Basin of Queensland have dispersive spoil. Based on an estimated area of 20,000ha and a rehabilitation cost of AUD$100,000 to AUD$150,000/ha, the instantaneous rehabilitation liability for the Bowen Basin alone is estimated at AUD$2 to $3 billion.Dispersive spoils present problems in post-mining rehabilitated landforms due to increased potential for surface and tunnel erosion, compromising the ability to achieve fundamental mine closure objectives of a safe, stable, non-polluting and self-sustaining post-mining landform (Minserve, 2004). Dispersion results in clay particles being mobilised and transported in water, even at low flow velocities (So et al., 1998; Minserve, 2004), and blocking of soil pores, resulting in surface sealing, crusting and reduced permeability (DNR, 1997; Vacher et al., 2004) which, in turn, further increases runoff (Dang et al., 2018).CITATION:Dale, G, Reardon-Smith, K, Thomas, E, Bennett, J, McCallum, L and Raine, S, 2018. A process-based approach to mine rehabilitation decision making using Bayesian modelling and risk-based principles for dispersive spoil rehabilitation, in Proceedings Life-of-Mine 2018, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993

Airblast overpressure legislative limits can be extremely difficult to meet throughout Australia, which has by far the most stringent limits of any nation in the world. As the difficulty in meeting the limits is strongly dependent on the scale of mining, it is not surprising that the Australian coal mining industry is experiencing particular difficulties in meeting these limits. Eight full scale overburden blasts have been modelled with respect to overpressure impact for a strip coal mine, involving both dragline (cast) blasting and pre-strip (non-cast) blasting. Overpressure levels in the range 100 to 125 dBL have been measured at distances varying from 2.4 to 5.7 km, and modelling has successfully estimated both the amplitude and shape of overpressure waveforms to within an average of 1.2 dBL. Typical errors of prediction are around 0.6 dBL. This accuracy of prediction has been achieved by considering the impact of only the face holes, and the accuracy of prediction of both shape and amplitude suggests that it is these holes which dominate the environmental overpressure impact at distances in the range two to six kilometres, for cast and pre-strip blasting operations. Modelling has been based upon the Elemental Overpressure Wavelet proposed by Richards and Moore (2002), incorporating actual hole coordinates, actual delay timing, and assumed delay scatter statistics. The incorporation of delay scatter statistics has been particularly significant, and allows the determination of the range over which the peak overpressure levels are expected to vary. To date, modelling has considered only the use of conventional pyrotechnic delays, though simple adjustment to the scatter definition would allow estimation of overpressure levels, and their variability, with electronic delays.

Jan 1, 2004

The recent description provided by Scott (1981) of the Ardlethan alteration systems is of particular interest as it draws attention to the analogy between Ardlethan and the porphyry tin systems of Bolivia (Sillitoe et aI, 1975).During 1978-1979 a parallel study of the mineralization confirmed that the extensive alteration pattern relates to a series of breccia pipes which provide access channelways for the mineralizing solutions (Clarke, 1979). Many of the results reported by Scott are difficult to interpret without this concept and this short discussion is intended to provide additional perspective to the proposed porphyry tin model.The breccia pipe systems are centred upon each of the major mineralized zones (Wild Cherry, Carpathia, Stackpool and White Crystal) and with the exception of the White Crystal collapse breccia the major pipes are of the hydrothermal intrusive type. They range considerably in size and shape and at least two ages of formation are revealed by their cross cutting relationships at the Stackpool, Carpathia and Ardwest regions. Individual pipes or groups of pipes have distinctive alteration/infill characteristics and the entire system can be viewed as a complex porphyry tin system evolving with time. The recognition of pipes of different types and ages reveals a situation considerably more complex than suspected by Scott, and hence both the geochemical data and modelling require reinterpretation.For instance, the geochemical data contained within Tables 2 and 3 (Scott, 1981) relate to two separate breccia pipes which correspond to the South Cherry and Ardwest ore zones respectively. Although it is probable that both pipes are temporarily identical it is important that the geochemical data be viewed in context. The brecciation is extremely difficult to recognize and it is probable that the chemical compositions given represent mixtures of altered fragments and rock flour, together with material precipitated from solution as matrix, along microfractures, within small vughs, etc.

Jan 1, 1982

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

The products of Lower Miocene calc- alkaline activity on the east coast of Northland, New Zealand are described and contrasted with coeval rocks of the northern North Island. These rocks, the Eastern Volcanic Belt (EVB), occur in four main centres aligned north-west to south east as either plutonic/hyabyssal bodies or as agglomeratic piles and dyke intrusions. Significantly the plutonic members always occur to the north-west of the volcanic members, probably indicative of differential uplift along faults (upthrown to the north) aligned perpendicular to the EVB. A full basalt-rhyolite (diorite-granodiorite/ adamellite) spectrum is represented, with a temporal progression towards the silica-rich endmembers indicated by cross-cutting field relationships. Modal mineralogy parallels this trend, consisting of two-pyroxene, hornblende, biotite, quartz/alkali feldspar modal assemblages, and with rare occurrences of olivine and garnet-bearing volcanic phases. Chemically the EVB is medium-K, calc-alkaline (with respect to AFM and total-Fe/MgO vs. Si02 indices) and quartz and hypersthene normative. The thirty two available K-Prisotope dates indicate that activity was largely confined to the Lower Miocene (24Ma-16Ma), with an apparent younging towards the south east. Initial B7Sr/e Sr ratios (0.70335- 0.70679) are indicative of a continental- arc-type setting, however it is unlikely that a straightforward tectonic reconstruction for this part, of the Pacific Margin is possible. Evidence from xenoliths, both petrologic and isotope, within EVB magmas and from regional geologic studies suggests that hypotheses pertaining to a volcanic arc sited over a subduction zone may hold little relevance in this case. The review concludes that the EVB developed from the partial melting of a geochemically evolved lower crust as indicated by xenolith evidence. This occurred in response to thickening initiated by a short-lived obductive event in the uppermost Oligocene, and controlled spatially by pre-existing basement structure. Intra-suite chemical and mineralogic variation reflects not only crustal variability, but localized differences in physico-chemical conditions best illustrated by the rare occurrences of olivine and garnet.

Jan 1, 1987

By P J. White, J V. Lawless

Low-sulphidation epithermal gold deposits, which form in quasi-hydrostatic convective hydrothermal systems, frequently contain chalcedony within high-grade ore, which has been interpreted to be a crystallisation product of amorphous silica. To deposit amorphous silica rather than another silica polymorph at elevated temperatures requires very high silica concentrations, because of its relatively high solubility. Only extreme boiling caused by decompression followed by wall rock heating upon structural dilation, can achieve this. As gold deposits with amorphous silica it must be produced by the same mechanism, particularly since extreme boiling is also a very effective mechanism for gold deposition. Recent developments support this view; the first is the detailed isotopic analysis of chalcedony-bearing high-grade veins reported from Hishikari, Japan, in which oxygen isotope results are indicative of extreme boiling and hydrogen isotopes indicate initial deposition of amorphous silica. The second is the finding of chalcedony within geothermal pipe work in the Rotokawa geothermal field in New Zealand. Rotokawa is a comparatively hot field (335¦C at depth); hence separation of the steam-water mixture produced by the wells is undertaken at a comparatively high temperature (220¦C) to minimise down-stream silica scaling. Even so, silica scale, some of which is chalcedony, does occur, under similar conditions to that in low-sulphidation epithermal deposits. Evidence of chalcedony forming under these conditions, reinforces the interpretation that decompressive boiling is the main deposition mechanism for gold in low-sulphidation epithermal deposits. It is possible that there is sufficient drop in temperature due to decompression that, at least initially, the silica deposits directly as chalcedony. Low-sulphidation epithermal gold deposits that do not contain chalcedony, such as those in the Philippines, may form at temperatures too high for chalcedony to directly form. The recognition of decompressive boiling as the main deposition mechanism in low-sulphidation epithermal deposits means that exploration can focus on zones where this has taken place by combining paleohydrological reconstruction and structural geology.

Jan 1, 2002

The Ross Goldfield is a unique gold resource. From its discovery in 1865 there was a growing understanding of the geology of the deposit as mining moved from the surface at Jones Flat in the south to underground extraction at Ross Flat further north. Multiple layers of gold-bearing gravels were penetrated in deep shafts and six rich gold-bearing bottoms were worked. The ultimate bottom on the Old Man Group gravel surface has never been reached either at Jones Flat or at Ross Flat. Mining at Ross Flat was ultimately halted by uncontrollable flooding, by escalating costs and by a shortage of labour during the First World War. Mining at Jones Flat recommenced in the late 1980s and attention has once again been drawn to the potential magnitude of the resource at Ross Flat. Research of historic literature shows that there is potential for a bulk gold grade of 400 mg/m3 in a volume of 82 million cubic metres of gravels which lie in a basin between Jones Flat and north Ross.

Jan 1, 1993

By G R. Hancock, J F. Martín Duque

Post-mining landscapes are required to geomorphologically and ecologically integrate with their surrounds (Martín Duque et al., 2015). Designing and constructing an erosionally stable landform is the first and arguably most important part of the rehabilitation process. Without an erosionally stable landform topsoil and nutrients are lost, shallow groundwater is depleted as well as when excessive erosion occurs, expose suboptimal materials. Here we examine the ideas of geomorphic design and rehabilitation and how the landform can be tested and enhanced using computer based design and landscape evolution models. Specifically we evaluate the complementary capabilities of landscape modelling (SIBERIA) (Hancock and Willgoose, 2017) and geomorphic design software (Natural Regrade with GeoFluv) (Bugosh et al., 2016), in order to maximise erosional stability on post-mining landscapes (Zapico et al., 2018). CITATION:Hancock, G R and Martín Duque, J F, 2018. Geomorphic design and landscape evolution modelling for best practice mine rehabilitation, in Proceedings Life-of-Mine 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989

With the theme of û æUnderground Ore Handling SystemÆ, Kopanang Mine completed an extensive project on a specific system with technologies for the handling of ore from a dedicated drawpoint to the shaft system. The intended rail haulage tramming system had to be capable of handling the shaft design and Life of Mine (LOM) requirements. Kopanang is an AngloGold Ashanti gold mine situated in the province of the Free State in South Africa. In the Sotho language the name æKopanangÆ means to come together as a team. ItÆs an appropriate name given that 25 companies worked on this project. The future focus at Kopanang is to establish four mining levels between 3 to 4 km south-west of the shaft and two mining levels to the west. The mine has an expected life of almost 20 years and capital was approved in order to access this reserve to establish the infrastructure to handle the ore, hence this exclusive rail haulage tramming system of close to R40 million (SA rands), which took three years to construct. Apart from the fact that this system had to be capable of handling 6500 t per shift at a depth of over 2 km over a length of 3.2 km, some of the major considering factors were: safety, economic factors with improved labour productivity, efficiency and reliability, risk termination, and ergonomics. The system comprises two 20 t locomotives operating in a double header configuration from a dedicated draw point to a dedicated tip area for the reef and waste ore. With the objective of handling high speed and high capacity, this 200 t payload train is capable of running at 35 km/h powered from a 500 volt ac overhead line. Each loco consists of two 90 kW dc motors with ac/dc power conversion on the locomotive. For the system to operate at this speed, the rail system is constructed with Class 1 rails over the entire hauling distance. The tipping mechanism is unique and the span of 11 hoppers each with a load of close to 20 t is capable of tipping the pay load of 200 t in about 20 seconds hands free.

Jan 1, 2005

The Acid Leaching Process for the Synthesis of Zeolitic Material from Paper Sludge Ash

Sep 13, 2010

By R Hoskings

Conceptual studies of the run of mine stockpiling and reclaiming requirements commenced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and compared with the alternatives. Foundations were designed to minimise cleanup effort and to ensure stability of equipment under design wind loading without storm bays. Programmable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

By K B. Quast, A Schuurmans

Laboratory batch rod and ball milling tests were conducted on samples of Heavy Medium Separator (HMS) sinks from Renison Limited. The effects of mill rotation speed, rod volume and ball size on the resulting product size distribution were investigated. Between 48 and 69 per cent of critical speed, the product sizing distribution curves remained very similar, with a finer grind resulting from increasing the speed of rotation at constant grind time. Increasing the rod loading from ten to 53 per cent by volume caused the product size to become finer and more closely sized with a transition occurring at approximately 29 per cent. This was interpreted as a change of dominant grinding mechanism from abrasion to impact. No preferential grinding of the cassiterite was observed. The effect of increasing ball size at constant charge weight was to preferentially grind the coarser particles and generate more intermediate sized particles, whereas the product from a mixed ball charge gave a distribution similar to that obtained when a charge containing only smaller balls was used.

Jan 1, 1998

By B Walker, A Robertson, C Wels, S Fortin

A background characterisation study was carried out in the Sangre de Cristo mountains, New Mexico, to: quantify naturally occurring contaminant loads from mineralised areas; define site-specific background concentrations; and to determine key factors controlling spatial and temporal variations in contaminant concentrations. The study included a comprehensive sampling and testing program (paste pH/EC, ABA, leach extraction tests) of soil/bedrock from mineralised areas (including erosional scars), and a ground water and surface water quality monitoring program in selected mineralised watersheds. Results demonstrate that high concentrations of contaminants occur naturally in ground and surface water draining the mineralised area of the Red River basin. The erosional scars were found to represent the major source of acid rock drainage (ARD) (~66 per cent) in this area due to: high rates of weathering and erosion, which continually exposes sulfide-bearing outcrops; and high rates of run-off as a result of high elevation and lack of vegetation. The scar material is generally very acidic (paste pH ranges from 8.5 to 1.5; average = 3.6) with highly elevated concentrations of sulfate and leachable metals. The composition and concentration of leachable metals vary significantly, not only between scars but also within a given scar. While all streams draining the various scar watersheds are highly acidic, each has a characteristic æfingerprintÆ of sulfate and metal concentrations. Most of the run-off from the scars infiltrates into alluvial debris flow aprons and reaches the Red River via groundwater flow.

Jan 1, 2003