Search Documents

By G J. Lyman

The theory of sampling has progressed slowly over the last century. The concepts of correct sampling were known to mining engineers such as D W Brunton in the 19th century. It was recognised early in the 20th century that the Poisson distribution of particles carrying the target analyte was the key to the uncertainties between samples of a given mass. However, no efforts were made until the 1980s to determine the entire sampling distribution as a function of sample mass. The variance of sampling was made clear by Gy and others, but none attempted to determine the entire sample assay density function until J H Venter in South Africa applied the method of characteristic functions to the problem.Venter applied the method to a specific case of very low analyte concentrations in samples of very fine particle size where his assumption of constant sample mass was justified. When his general methodology is applied to the more general problem, it can be shown that the assumption of constant sample mass is no longer justified and leads to some anomalous results for sampling variance. Venter’s method can be expanded to allow for a statistically variable sample mass and to take into account the size distribution of particles that carry no analyte.This paper presents the basis of Venter’s work and shows how the approach can be easily modified to yield results for the variance that are consistent, for example, with the work of Gy. It is also demonstrated that the entire sampling distribution can be determined without undue computational burden when sufficient information on the material heterogeneity has been collected.CITATION:Lyman, G J, 2014. Determination of the complete sampling distribution for a particulate material, in Proceedings Sampling 2014 , pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By P Allum

This paper presents a case study to reduce the operational cost on the secondary ball mill circuit in the Lead/Zinc Concentrator at Mount Isa Mines. The circuit includes two five-metre diameter ball mills each closed with a cluster of ten 15-inch cyclones. The operating cost for both ball mills is about six million Australian dollars per annum.The concentrator achieves 75 per cent of the plant design capacity with one ball mill operating, but will have to use two ball mills when 100 per cent plant capacity is required. The optimisation study on the circuit identified a new flowsheet that enabled the concentrator to reach 100 per cent of the capacity by using one of the two secondary ball mills. The success of the project utilised the existing equipment rationally and saved the operational cost for one ball mill at full concentrator capacity. A further simplified secondary circuit is proposed using the IsaMill for the secondary grinding duty. Performance of the IsaMill circuit and the potential cost savings are predicted.

Jan 1, 2002

By A Roseman, T Gruber

Traditional methods for installing gaskets for segmented bored tunnels have relied upon different bonding procedures with adhesives that carry a series of disadvantages to segment producers. Fixation of the gaskets into the concrete segment as part of the casting procedure has been developed over the last 20 years and has emerged as an economical solution to produce high-quality tunnel segments for various technical tunnel applications. This paper investigates the advantages of using anchored gaskets, the different tunnel systems that employ anchor gaskets and reviews the first anchor gasket project; the Lee Tunnel and analyses how segment production efficiencies are gained.CITATION:Gruber, T and Roseman, A, 2014. Use of anchored gaskets in segmented bored tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 253–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Leigh J. H

A history is given of the dust control techniques developed and applied by the mining companies at Broken Hill. A history of the regeneration works undertaken since 1936 is out- lined. Particular emphasis is placed on the stabilization of mine residue dumps which are located throughout a belt of mining leases in the middle of the city and which began in 1937. The establishment of vegetation for dust control techniques is discussed in detail and a case study is given of the successful revegetation of the sides of a 650 metre long, 350 metre wide and 35 metre high residue dump.

Jan 1, 1976

By D Jeffery, R Whittering, G Lane

Most aspects of process design are best addressed via bench scale or pilot plant scale test work. However, as experience is gained, fundamental or indicative data can provide more than adequate information to manage the risk associated with some process aspects of concentrator design.Historical precedence exists where minimal design test work has resulted in successful projects. On many occasions benchmarking, sometimes supported by fundamental data such as mineralogy, has been used to successfully develop effective process plant outcomes. Of course, this style of approach is most common with æfast trackÆ projects and often comes with the usual surprises that result from inadequate geometallurgy to define the project cash flow.This paper explores the risks and opportunities associated with the various facets of process development and design for a base metals concentrator. The paper is intended to provide guidance to project managers rather than address the technical aspects of process engineering.CITATION:Lane, G, Whittering, R and Jeffery, D, 2012. Benchmarking versus test work - How should you manage process risk?, in Proceedings Project Evaluation 2012 , pp 49-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

Willyamite from the type locality, Consols mine, Broken Hill, N.S.W., has been re-examined, and found to consist of zones with widely different Co:Ni ratios. The name willyamite is redefined to include the portion of the (Co, Ni)SbS series with cobalt in excess of nickel. Willyamite is pseudo-cubic, with the three axes equal to within 0·001 A.

Jan 1, 1970

THE furnace described in this paper was installed and has been used by the writer for the melting of rich gold-bearing material, and has given complete satisfaction. It may, therefore, prove of interest to other metallurgists who are faced with a similarproblem. A furnace of this type should be most suitable for the reduction of "cyanide preeipitate," "charcoal ash," "anode sludge," &c. formerly the melting was done in fire-clay crucibles, using coke or crude oil as fuel, but this method is costly, slow, and unsatisfactory. A small water-jacketed blastfurnace was also tried on this material after briquetting it, but was discarded in favour of the electric furnace. The furnace may be described as a simple form of the Heroult resistance furnace, with an adjustable upper electrode and a fixed bottom electrode. This is in accordanee with Stansfield's classification of electric furnaces. The heating is mostly due to the resistance offered the current by the molten slag. The melting chamber consists of a steel drum 14 in. in diameter and 21 in. high, and is lined with silica bricks specially made to fit the shell. The internal diameter is G in. The bricks contain 92 % silica, are made from calcined quartzite bonded with fireclay, and are similar in composition to those used for lining steel converters. They are set in a mixture of finely-ground quartzite and clay, and well dried out. The shell is bolted to a steel plate, which forms the decking of a truck running on rails, so that the furnace can be moved under ahood for carrying off the fumes. A cast-iron slag spout is bolted to the shell below the tapping hole, which is 4 in. from the bottom of the shell. Opposite this another hole 1 in. in diameter is drilled through the shell and lining for the passage of the lower...

Jan 1, 1918

The Inglewood Gold Project consists of several titles in and around the Inglewood and Wedderburn Goldfields which were purchased from Strata Mining Corporation (now Excalibur Mining Corporation). The Inglewood goldfield has a historical production of approximately 160 000 tonnes at 23 grams per tonne. The company has reopened and developed the Maxwells reef, picking up a high-grade shoot (Max Shoot) identified and worked by Goldquest et al up until 1994. Production ceased on a low gold price, rapidly reducing vein size and a requirement for further development. Greater Bendigo Gold Mines Ltd (GBM) has undertaken the development and encountered the mineralised vein in an increasing size setting with high grades and the existing mine development has access to a further shoot to the north (Max North Shoot). The Maxwells reef also contains the Woolf shoot south of the Maxwells shaft and an inferred resource of ~20 000 ounces is contained from 60 m below surface. Best intersection 2.9 m at 50 g/t. The Maxwells reef area produced approximately 20 per cent of the Inglewood goldfields production and GBM is preparing to increase its exploration efforts across the rest of the field. A processing plant has been constructed at the Maxwells mine site, which is capable of treating tailings, hard rock and alluvial material utilising gravity recovery. The existing Maxwells tailings have been excavated and treatment commenced. It is intended to produce a sand product from the tailings for resale and to reduce the storage requirements per tonne. Several large water dams constructed by Goldquest in the 1990s are being re-engineered to enable storage of significant tonnages of tailings. A level of surface and underground production is planned for 2008 and this is to be expanded into 2009 and beyond. The long-term future at Inglewood is envisaged as structural repeats at depth below the current workings and a project plan to gain deep access will be prepared on successful drilling results.

Jan 1, 2008

There is no other effective way for study ing firedamp and coaldust explosions than to produce controlled explosions in a pre-monitor- ed environment - either mine openings kept for the purpose, or special surface galleries. Such explosion testing facilities have been employed historically at Buxton in U.K., with lesser known installations at Bruceton, U.S.A., Tremonia, West Germany, Katowice-Mikolow, Poland and elsewhere. Both firedamp and coal dust explosions are studied. Normally coal dust explosions are initiated by somewhat standardised methane air mixtures, by explosives, or purely by coal dust. Various structures and suppression installations are installed in roadways and galleries prior to explosion to simulate destruction and suppression, and the results of such tests form the basis of suppression installations, especially stone dust barriers and water barriers. Other data collected from these experiments include rev- ersals of explosion waves, pressures and temperatures and duration of explosion waves, analyses of aftergases etc. Other uses of explosion testing galleries include testing of explosives, electrical equipment and frictional . sparking.

Jan 1, 1981

By D Thornton, R Hodson, D Sprott

Blast fragmentation size distribution and thus blast design have been found to have a direct impact on the load and haul cycle through excavator dig time and bucket payload. Previous studies have demonstrated that by reducing the excavator dig time and increasing bucket payload, significant improvements can be made in both productivity and unit cost. Simulation work reported in the literature indicates that a 20 per cent improvement in dig time may result in only a three per cent improvement in load and haul productivity and unit cost. At the same time, a ten per cent improvement in bucket payload will directly translate to a ten per cent improvement in load and haul productivity and unit cost. Based upon these findings, extensive laboratory and field work have been undertaken in the past to correlate blast fragmentation distribution to bucket payload. In contrast, the literature reports limited studies quantifying the impact of blast fragmentation on excavator dig time. Field work was conducted at Placer Dome Asia PacificÆs Granny Smith Mine (Wallaby Pit) in Western Australia, concentrating on quantifying the impact of blast fragmentation on the dig time of a Liebherr 994 hydraulic excavator (shovel attachment with 14 m3 bucket). Fragmentation was assessed for each truck load of material using the Split Desktop system, while the excavator cycle analysis was conducted manually. Measured fragmentation P80 (fragment size at which 80 per cent of material passes) values ranged from 200 mm to 1200 mm. The field study investigated the impact of various fragmentation parameters (P20, P50, P80, cumulative per cent passing 250 mm size fraction, and uniformity index) on the average and total dig times. The results indicate that the fragmentation P80 provides the best correlation to average dig time (total dig time divided by the number of bucket passes to load a truck). The total dig time was found to be dependant upon the fragmentation P80 and the number of bucket passes to fill a truck. Monte Carlo simulation results, based upon these relationships, indicate a 26 per cent improvement in average dig time and a 12 per cent to 46 per cent improvement in total dig time (bucket passes ranging from 4 to 8), with a change in fragmentation P80 from 600 mm to 200 mm.

Jan 1, 2003

By A Unlutepe

The Bosphorus Rail Tunnel Project, located in Istanbul, Turkey, aims to provide a Euro-Asian rail link, via an immersed tube tunnel crossing the Bosphorus Strait, along which will run all commuter, freight and intercity passenger trains of Turkish State Railways (TCDD), as well as the future extension to the European rail network. The total length of upgrading and new railway construction will be approximately 76 km. The main structures include the immersed tube tunnel; mechanised shield tunnels; new Austrian tunnelling method (NATM) tunnels; cut-and-cover, at-grade and retained-cut/fill structures; and some service structures. This paper discusses Phase 1 implementation of the project, one of the major transportation infrastructure projects in the world today, whose varied structures present stimulating engineering and construction challenges.

Jan 1, 2008

By Gresham J. J

The rapid and successful development by Western Mining Corporation Limited (WMC) of a gold mining industry based on the deposits of the Kambalda-St Ives group, was the final chapter in a story that started some 85 years earlier. Although the exploration work that led to the development of the current mining operation took place in the 1970s and 1980s, the successes had their roots in the 1890s and it took three gold rushes, and separate uranium and nickel exploration booms to make the discoveries Possible.

Jan 1, 1991

The Western Australian Mineral Sands Industry has tried a number of different mining methods to efficiently exploit the potentially very large reserves of mineral sands in this state.The size of the operation, the location, the type and composition of the orebody contribute towards the choice of current mining techniques.The methods applied to these areas are described as well as reference made to other techniques which will . make possible the exploitation of lower grade reserves.

Jan 1, 1986

By G K. Robinson

The existence of bias in samples taken by cross-stream sample cutters has been investigated using three-dimensional discrete element method (DEM) modelling. Detailed quantitative information on overall extraction ratios, size specific extraction ratios, missed and extra sample components can be made by comparing a reference sample to the actual sample. A key advantage of using this modelling approach over physical experimentation is that the reference sample can be measured on precisely the same portion of the stream of material as the actual sample, thereby allowing the elimination of a significant fraction of the variability and allowing statistically significant results to be obtained using many fewer replicates. Quantitative analysis of results broadly supports the commonly-used rule that the cutter aperture should be at least three times the nominal top-size of the material being sampled, but does not support the commonly-used rule requiring increase in cutter aperture if the cutter speed exceeds 0.6 m/s. Sampler performance can be understood in terms of the balance of forces in the congested region of material formed by the slowing of the particle stream due to collisional interactions around the mouth of the cutter.

Jan 1, 2008

By N McIntyre, J Smart, J Ossa-Moreno, D Rivera

Hydro-economics is a field of research that analyses water resources from a multi-disciplinary approach (Harou et al., 2009). These models generally include one component that describes the water resources of the catchment being analysed (e.g. the physical behaviour of water), an economic component that describes users’ water demand function (changes of willingness to pay relative to availability) and a coupling methodology. These models go beyond calculating cash flows for water investments and analyse the economic behaviour of users when facing water shortages or surplus. In other words, water demand curves are defined for each water user (e.g. urban, agriculture, mining, environmental and hydropower), and they are used to retrofit the water resources component. As a result, the model approximates the catchment scale response to droughts and wet periods, including the effects of water markets, restrictions, recycling, water sharing and any cooperative efforts by users to adjust to changing climate conditions.These models are usually focused on agriculture and urban users, the main water consumers in most catchments, but they have sometimes included environmental, industrial and hydropower users (Bekchanov, Sood, & Jeuland, 2015). Nevertheless, although a relevant user of water in several catchments, the mining industry has been rarely included. This paper is part of an ongoing project that addresses this gap by developing a hydro-economic model in the upper section of the Aconcagua River in Chile. The aim of the paper is to analyse the sensitivity of the outputs of the model to changes in input data, both hydrological and economic, and to develop insight on usefulness of such models for reducing water conflicts in mining regions.CITATION:Ossa-Moreno, J, McIntyre, N, Smart, J and Rivera, D, 2018. Sensitivity of a hydro-economic model in a mining region to changes in hydrological and economic inputs, in Proceedings Life-of-Mine 2018, pp 52–55 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

During the 1960s chalcocite ore was mined from the Black Rock open cut. A large amount of this uneconomic material was not treated by the No 3 Concentrator at the time and as a consequence a surface stockpile was created which contained 750 000 tonnes of material at an average of 1.5 per cent copper.Laboratory trials indicated that due to oxidation, an average of 25 per cent of the copper was water soluble and the remaining copper was leachable using a sulphate/ferriclbacterial leach. On the basis of these trials it was decided to investigate the feasibility of producing copper via a leach SX-EW process. The investigation proved the process was feasible, so began the design, construction and commissioning of a 10 tpd (cathode copper) Copper Leach SX-EW Pilot Plant. CMPS Pty Limited in a joint venture with John Holland Engineering Pty Limited were awarded the turnkey contract for the design, construction and commissioning of the Pilot Plant.

Jan 1, 1993

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

By Johnson RW, Rogerson R

New perceptions of the nature of volcanic hazards on Bougainville Island have resulted from a recent remapping of the geology of the island. Ignimbrites and calderas have been identified at six Quaternary centres (Emperor Range, Tore, Kunua, Billy Mitchell, Loloru, and Laluai), and large-scale explosive activity now must be identified as a significant volcanic hazard on the island. Billy Mitchell and Loloru volcanoes are identified as the most likely sites of future, major, explosive activity. Billy Mitchell was recognised formerly as an extinct volcano, but is now known to have produced major eruptions 370 and 918 years BP. Five ignimbrite units recognised at Loloru range in age from about 12 700 to 3200 years BP. Bagana is an active volcano in central Bougainville, but its explosive activity is relatively minor and does not significantly affect areas beyond the uninhabited area of the volcano itself. Balbi is the largest volcano on Bougainville and has an extensive geothermal area at its summit. It was thought to have been in eruption last in the early nineteenth century. However, 370 and 940 year BP plinian ashfalls from Billy Mitchell cover the central area of Balbi, so the latest significant activity from Balbi may have been at least 1000 years ago.

Jan 1, 1990

L&M have been involved on the Shotover since 1980 when we joined Jack and Barney Ryan, who had started in 1972 with gold at $45 per ounce after a successful career as roading and demolition contractors in Christchurch. The first 85 tonne plant was a typical NZ trammel-riffle table plant with an armour plated hull for surviving Shotover floods, and was fed by a 53 tonne UH20 excavator. All this gear had to be carted in over the Skippers road on a small truck or sledge for the heavy loads. This operation was successful and generated the cash flow to sample the lower section of river and plan a second plant. To reduce fine gold losses this was planned to be a jig recovery plant and also included a vibrating screen which saved space and weight over a trammel. There are five flowlines of primary jigs and one secondary, followed by two Knudsen bowls for cleanup.

Jan 1, 1985

By Flloyd J. M

A continuous oxygen probe,incorporating a SIRO2 solid electrolyte oxygen sensor which measured the oxygen potential of a small volume of gas enclosed above the melt's surface,was constructed and tested. The oxygen potential of iron-silicate slags in equilibrium with solid iron in the temperature range 1250 to 1300¦C were measured continuously for tests of up to 40 hours duration. Results were in agreement with those of previous workers using gas equilibration techniques. Tests on non- iron buffered slags proved unsuccessful due to corrosion of the probe's component in contact with the slag and an alternative material is Required.

Jan 1, 1987