Search Documents

By C Noble, J Webster-Brown

A survey of selected West Coast Streams was undertaken in Summer 2001, Summer 2002 and Winter 2002 to establish the degree of arsenic (As) contamination in waters and sediments downstream of old coal and gold mine workings on the West Coast. Of the catchments studied, Soldiers/Ford Creek and Rapid Stream showed the most significant elevated As concentrations, predominantly in dissolved form, and evidence of AMD or ARD contamination (high sulfate concentrations and/or acidity). The rate and processes of removal of dissolved arsenic from the water column (attenuation) have been studied in these catchments. The Rapid Stream and Soldiers/Ford Creek catchments are directly affected by adit drainage from the Sullivan and Blackball coal mines respectively. Both catchments have high As concentrations in the sediments, with up to 770 mg/kg in Soldiers Creek and 490 mg/kg in Rapid Stream. Dissolved As concentrations are significantly elevated in the neutral pH waters of Soldiers Creek; typically as high as 100 - 200 ¦g/kg, up to 500 m downstream of the main adit discharge (800 ¦g/kg As). Adit inflows to Rapid Stream were acidic and contained 20 - 30 ¦g/kg dissolved As, with relatively high concentrations of arsenic in the stream water in winter (up to 18 ¦g/kg), but not in summer. Analysis of concentration trends and As:SO4 ratios downstream of these obvious As sources confirmed that dissolved As had been actively removed from the water column, but varied seasonally with greater removal evident in summer. Adsorption of arsenic onto iron oxide in the stream sediments is the most likely mechanism of removal. The Snowy River catchment, on the other hand, has relatively high As concentrations in both the sediments and the water column, but there was little evidence of a distinct AMD or ARD input from the Blackwater gold mining area. Preliminary investigation suggests that dilution rather than attenuation is responsible for decreasing As concentrations downstream.

Jan 1, 2003

By Jones S. C

The problem of sealing a fluid serieite zone at a hole depth of 4000 ft was overcome by using a composite non-return valve plug and rod assembly which enabled cement to be forced under pressure into the zoneà

Jan 1, 1966

By S Hanrahan, S McLaughlin

A case study is presented that details the safety journey at a North American project involving two major contracts: a 1000 m shaft recovery and rehabilitation, and the development of a drainage gallery in a large open pit operation. In the early stages of the contracts, there were a number of incidents that created tension between the owner and contractor, which resulted in the contractor being placed on a final warning with almost imminent potential termination. As a result of this, it was agreed to initiate a focused safety recovery plan as a ‘last chance’.Over a period of two years, the engagement and consequent performance of the contractor was turned around, steadily working to set it up for success such that in one of the contract work areas, a record of ‘one year LTI (lost time injury) free’ was achieved. The journey involved the owner and the contractor teams working cohesively to educate all parties in the safety requirements and, most importantly, providing the context and understanding for certain requirements being put in place. Early on in the process, it was recognised that the owner team unknowingly was an impediment in that they did not fully understand the safety requirements and so was not able to lead the way for the contractor effectively. The journey to rectify the situation was supported and followed up by focused engagement with the project team, which generated a progressive improvement in a very challenging environment.In particular, the contractor turnaround was significant and of enough value for the contractor to ultimately export some of the safety systems from this site to other contract sites. This demonstrated the ultimate benefit of the contractor understanding and buying into a safety culture and system.CITATION:Hanrahan, S and McLaughlin, S, 2016. Winning the safety battle, in Proceedings International Mine Management Conference, pp 181-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

The oxidation of sulphide minerals in aqueous suspension is discussed from several viewpoints. Limitations of our present knowledge are pointed out, and several points where further information would be of special interest are mentioned.Firstly, some properties of minerals and their effect on oxidation are discussed. Properties of different species, such as crystal structure, lattice bonding, and "metallic" properties are mentioned, and then the effect of variation within a given species is discussed. The effect of physical factors, especially particle size, is also considered. Other variables discussed include the importance of solution composition, and its effect on the nature and rate of reaction, and the use of various oxidising agents. Some factors concerned with the whole system, such as temperature, pulp density and stirring rate are then considered.Finally, the nature of various oxidation products is discussed with reference to the kinetics of reaction and the nature of the rate limiting step. It is suggested that more attention should be paid to electrochemical explanations of the reaction mechanism.INTRODUCTIONKnowledge of the factors governing the rate of oxidation of sulphide minerals in aqueous suspension is a prerequisite for the effective control of many ore treatment operations. Rapid oxidation of sulphides is usually desired during the leaching of sulphide ores and concentrates, but in the cyanidation of gold ores, or in the leaching of uranium ores, any oxidation of sulphides may be regarded as an undesirable side reaction. Knowledge of many of the factors involved is also of interest in connection with the oxidation of sulphides in flotation circuits and in natural ore forming processes.Systems for which some reasonably quantitative data have been published are listed in Table 1. Qualitative...

Jan 1, 1961

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

By Basillo CI

The adsorption mechanisms of various thiol collectors can be subdivided into four classes: chemisorption, EC-mechanism, catalytic oxidation and metathetical substitution. The chemisorption mechanism occurs at potentials below the thermodynamic potentials for the metal-thiol compound formation and is reversible. The EC-mechanism occurs when the mineral is sufficiently oxidised to liberate metal ions to form metal-xanthates; therefore, it is observed with more easily oxidisable minerals and/or with collectors having large pK values. Thionocarbamates adsorb on sulphide minerals via the EC-mechanism due to their large pK values. Although the adsorption occurs at very low potentials as compared to xanthates, it is irreversible with large overpotentials. On the other hand, the adsorption of modified thiophosphates and thiophosphinates occurs near the thermodynamic potentials because of the low pK values. The metathetical substitution is believed to occur only when a mineral is highly oxidised. These classifications are useful for studying the effects of electrochemical potentials and the molecular structure on the collector adsorption Mechanisms.

Jan 1, 1993

By N Ozawa, R Kaneko, M Arimit

The Mitsubishi Higashitani limestone mine is a ten million tonne per annum operation located near the city of Kitakyushu on JapanÆs western island of Kyushu. Higashitani is one of the largest limestone mines in Japan and accounts for about five per cent of national production. Blasting practices at the Higashitani mine involve the use of bagged ANFO, dynamite primers and non-electric detonators. Regulations in Japan prohibit the use of site mixed bulk explosives. Blast size is usually around 17 000 tonnes with 20 holes in a single row, two or three blasts are fired per day at a powder factor of between 0.25 and 0.32 kg/m3. As part of a program looking at oversize reduction Mitsubishi, Asahi and Orica agreed to conduct a joint project at the Higashitani mine to investigate the relationship between the powder factor and fragmentation. The first stage of the project was to benchmark the current blasting performance. Five blasts were monitored in each of the 210 (hard rock) and 220 (soft rock) areas of the mine. OricaÆs Powersieve« software was used to measure fragmentation and total rock breaker hours were also recorded for each blast. OricaÆs computer blasting simulation model Sabrex« was used to prepare revised blast designs with a higher powder factor and predict their performance. The performance of these blasts was monitored using the same methods.

Jan 1, 2004

By N E. Whitehead

An application to mine an ilmenite-rich sand deposit in Westland led to public concern about potential radioactive hazards should the ore be further processed to recover zircon or monazite. A review recommended that any material involved in the heavy mineral sand industry containing more than 0.05% thorium, uranium or their mixture should be considered a radioactive substance and, for mining purposes, a notifiable product. Safeguards for those occupationally exposed would operate via the Radiation Protection Regulations. The major safety requirement would be the minimisation of dust in certain operations.

Jan 1, 1993

By S D. Golding, K Baublys, V Nanjappa, C J. Moran

Water reuse is becoming an integral component of the water management strategy on mine sites. This practise is being driven by corporate sustainability goals, community and societal pressures to demonstrate improved water stewardship, as well as climate and regulatory pressures. However, water reuse often results in water quality compromise which can then result in decreased recovery through problems in processing circuits, product quality, and an increased likelihood of discharge of water that cannot meet environmental regulatory requirements. On most mine sites, there is usually a disjuncture between water quantity management and water quality management with the latter being managed solely as an environmental problem. It is becoming increasingly clear that water quality and quantity must be managed as an integrated system. In order to integrate water quality and quantity management to achieve multiple objectives the dynamics of water and constituents must be understood. Using examples from a study being conducted at a coal mine in the Bowen Basin, this paper will outline the dynamics of water and salts on the site.

Jan 1, 2009

Effect of Matching Relationship Between Bubble Size and Particle Size on Kaolinite Flotation

Sep 13, 2010

By Zhang S

A probabilistic approach is proposed for updating open pit slope sta- bility based on successful performance. The suggested approach is developed within the framework of Bayesian probability theory. In seeking solutions to geomechanics problems consideration must be given to inher- ent variability of shear strength parameters and to the errors in the esti- mation of these parameters. The latter can be significant and may lead to consistent overestimation or underestimation of the values derived from site investigation and testing. Conventional deterministic methods of slope stability analysis do not allow systematic modelling of uncertainties in applied loads or in shear strength parameters. Within a probabilistic framework indicators of stability may be calculated, e.g., the reliability index and the probability of failure. Based on observation of slope per- formance at any given stage of a project, the mean or the standard devi- ation (or both) of a shear strength parameter may be updated. Consequently the indicators of stability can also be updated. The appli- cation of such an approach is demonstrated by an illustrative example.

Jan 1, 1989

By T van der Meer, A Salokannel, M Martikainen, L M. Nevatalo, J McCulloch

Water use and wastewater management is becoming a focus for many industries around Australia and the rest of the world. Good quality water is increasingly being recognised as a precious resource, and regulations on the bulk storage and discharge of waste streams is becoming more stringent in order to protect the environment, existing water reserves and the communities that use these resources. Components such as heavy metals, arsenic, cyanide, and sulfate from acid mine drainage are some that occur at mining and metallurgical processing sites. Removal of such components can allow safe re-use of these streams, reducing the new water requirements of the process, or else allowing acceptable discharge to the environment. Re-use or discharge of treated water eliminates or reduces the risk associated with storage of large volumes of contaminated water on site.Technologies where a contaminant is selectively precipitated and removed as a sludge are used for many of these treatments. Selection of the best treatment option for wastewater must depend on what is suitable to each site, and consider not only the nature of the contaminant, but also other aspects, including the location and situation of the site, local regulations, cost of reagents, the sensitivity of the local environment and waste sludge disposal options. To outline how an effective and economical solution can be designed and delivered, this paper will present a case study for the removal of arsenic from a site wastewater, from assessment of the problem, selection of suitable technology, design and implementation, to the benefits delivered to the site.CITATION:Salokannel, A, Nevatalo, L M, Martikainen, M, van der Meer, T and McCulloch, J, 2013. Technology selection for removal of contaminants from an industrial wastewater, in Proceedings MetPlant 2013 , pp 531-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

After the minim operation, most raw materials that occur in the earth's crust require some form of processing or refining before they can be converted into a final end product. In the mineral industry these remarks apply to materials such as iron ore, bauxite, limestone, copper ore and many others that are found in Australia in large quantities. Processing plants for these raw materials operate more efficiently, however, if the feed to them is consistent in both physical and chemical characteristics. Such uniformity rarely occurs in nature so that some form of homogenisation, or blending, is required ahead of the processing plant. Bending also assists the mining operation itself by reducing; the need for selective mining and, by combining high and low grade materials, a more uniformly graded, commercially acceptable product can be obtained, thereby increasing the commercial life of a mine or quarry. Bed blending is the most efficient of the processes available, and following its development in the United States in 1905, over 100 plants have been installed, or are under construction, all over the world. The original process, the Robins--Nessiter system, has been the subject of continued improvements and refinements, so that economical capacities are possible from less than 100 l.t.p.h. up to 10,000 l.t.p,h. and beyond.

Jan 1, 1969

Drill blasting is a widely used method for rock fragmentation in mining, quarrying and construction industries. Environmental effects such as air shocks, dust, flying rocks and ground vibration are unavoidable results and undesired effects of blasting. Among these ground vibrations can have a damaging effect and may influence on long distances. Therefore various researchers have developed mathematical models to predict ground vibration after blasting. These models take into account the amount of explosive, distance and several coefficients related to the field under investigation. The developed models to predict ground vibration may yield different results for the same case. Selection of the most suitable model requires engineering judgment and evaluation of models. At this point, a computerised system helps the engineer to evaluate and select the most suitable model in order to design and plan a blasting pattern. The safe charge of explosive and magnitude of vibration after blasting should be predicted beforehand. Therefore a computer program namely 'prediction of blast induced vibration' (P-BIV) has been developed. This paper introduces and presents a computer program (P-BIV) which includes the set of models developed to estimate ground vibration to provide blasting engineers a tool to determine the amount of explosive for safe blasting.

Dec 6, 2010

By Molloy GR, Eaton RA

The crusher development programme for 7ft Super Extra Heavy Duty (SXHD) Symons cone crushers commenced in 1984. The main objective of the programme was to run the crushers at maxi- mum power for the full life of the liners. This would give a finer product sizing enabling grinding and flotation plant throughput to be maximised. The study was conducted along two basic lines of attack, the first main- taining an effective profile through the life of the liners, the second improv- ing the properties of the liners. It has been found that crusher liner life can be extended and crushing efficiency improved by modification of liner composition and profile.

Jan 1, 1988

Exploring long-term future possibilities for your business and methods for achieving them are critical functions of leadership. More than ever, strategic initiatives today have to be planned and delivered in an environment of disruptive change û driven by shifting business or regulatory imperatives, new technologies and global economic change, and diverse stakeholder interests. The notion of The Future as a single inevitable outcome is obsolete. There are many possible futures. This paper explains an innovative process û known as scenario planning û to help executives in the construction and testing of longer-term strategies to deal with uncertainty.

Jan 1, 2006

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

Uranium exploration over a wide area of the Southern Frame Embayment, South Australia, has defined a number of Lower Tertiary fluvial palaeochannels incised in older rocks. The buried channels contain similar stratigraphicsequences of interbedded sand, silt, and clay, probably derived from the adjacent uranium-rich Olarv Provinee. Uranium mineralization is pervasive within two major palaeochannels, and four small uranium deposits have been found in the basal sands of these channel sequences, at the margins of extensive tongues of limonitic sand.One of the channels is examined in detail with respect to channel morphology, stratigraphy, and rock alteration and the geology and ore controls of the contained uranium deposits are described.A geochemical zonation reflected by variation in limonite, pyrite, carbon, and humic malleI' is defined across one of the deposits. A genetic model is proposed suggesting formation by a uraniferous geochemical cell which migrated down the stream gradient and concentrated uranium on its lateral margins adjacent to the channel bank.

Jan 1, 1978

This paper describes how Western Mining Corporation uses sophisticated diesel equipment in mining of shallow flat dipping narrow ore- bodies in the Otter Juan area. Though in most cases the stoping method chosen relies on hand held conventional equip- ment, the 'ore handling systems have been designed to allow for a relatively high degree of mechanization. The use of diesel loaders, trucks along with three boom jumbos is described. A single one in nine decline driven as the means of access to the various ore surfaces at Otter/Juan resulted in the first ore being produced first 15 weeks after the first round was fired in the Ore-Decline. Now, three years later, the.mine is in full production, and in 1971/72 produced 392,000 dry tonnes of high grade Nickel Ore.

Jan 1, 1973