Search Documents

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976

Limnological processes are often overlooked when trying to assess the long-term water quality of pit lakes. It is essential to deal with these aspects, since they determine the geochemical and redox conditions around the submerged reactive rocks. Underground mining at East Sullivan (northwestern Quebec, Canada) stopped in 1966. Two adjacent stopes, 91 and 106 m deep, were left open to the surface, with roughly circular apertures of about 7700 and 18 000 m2. Water filling of the two glory holes went on over three decades and overflow began in 1999. Surface water pHs values were near neutrality as late as 1994 (6.3 - 7.0) but had become acidic by 1999 (2.6 - 3.5). Limnological processes were investigated in late-1999 and early-2000, with temperature measurements at 1 m intervals and sampling of the water columns before and after the late fall density inversions. A strong chemocline-thermocline was observed at 15 m. Above the chemocline, the water had low pH (3.2), no alkalinity, and low Na, Ca and sulfate. Below the chemocline, the concentrations of these parameters and the pH increased, with pH at 5.5 - 6. Consistent with the low pH values present in the upper 15 m, the concentrations of Al, Cd, Cu, and Zn were high near surface, and decreased below the chemocline. Dissolved oxygen concentrations as well as Eh decreased with increasing depth. Alkalinity integrated over the entire water column below the chemocline was at least six times larger than the acidity inferred from Fe2+ and Fe3+ concentrations. The temperature survey showed that seasonal density inversions do occur in the water column. The inversions do not involve the entire water body, since the surface to depth ratio is too small for a complete overturn. Oxygen from surface waters is carried to the bottom where it oxidises sulfides, until its depletion. Residual Fe2+, stable under anoxic conditions, is displaced upward by the next dense water incursion. It eventually reaches the thermocline, but only after many successive incursions. There, its oxidation to Fe3+ allows hydrolysis, which consumes dissolved and wall-rock alkalinity. It is only in 1999 that alkalinity was finally exhausted and that the pH shifts to acid values. The low pHs in the surface waters allow a build up of Fe3+ and Al3+, and desorption of metals from colloids. Buffering is assumed to be controlled by wall-rock oxyhydroxides in surface waters, and by carbonate minerals in the bottom waters. Because the seasonal overturns are far from being complete, the large amounts of alkalinity acquired from the wall-rock in the bottom waters cannot balance the acidity of near surface waters. Hence the surface water is acidic.

Jan 1, 2003

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors' structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors' reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

By Floyd JM

Pilot plant trials showed the effective ness of the submerged lance SIROSMELT technology for altering the composition of iron blast furnace slags as a preliminary step to produc- tion of formed materials. Mixtures of oil and air were injected into a bath of liquid slag to provide the heat required for melting the additives and to provide very turbulent conditions which resulted in complete dissol- ution of added fluorspar within one minute and almost complete dissolution of silica in two minutes. Sulphur lost during injection was readily made up by addition of pyrite or pyrrhotite. A stable foam could be readily made and broken down and the foamed slag appeared suitable for extrusion or forming into shapes.

Jan 1, 1979

By Mercer JK

This paper gives a description of the research undertaken by an explosives manufacturer to give better technical advice to the Mineral Industry. Blasting Physics is defined as giving a systematic and coherent account of the initiation and subsequent effects of high explosives upon the surrounding medium. As a result of this work a mathematical model based on the gener- ally accepted mechanism of blasting has been developed. The mechanism and the resulting model are briefly outlined. IFrom'this model the effects of burden, spacing, blasthole diameter, rock and explosive properties upon fragmentation and heave can be calculated. Using these calculations it is then possible to see how variations in frag Imentation and heave can affect the overall production costs of a mine whether it is surface or underground. The overall costs are made up of a number of individual costs - drilling, blasting, loading, hauling and crushing. ach of these operations influences or is influenced by fragmentation and heave s these costs are inter-related, the

Jan 1, 1975

By L S. Shekhawat, M P. Roy, R K. Paswan, P K. Singh, A Joshi

Blasting in the mining industry is being transformed, and can no longer be treated as an art or a practice purely dependent upon experiences of individuals. Examples of key drivers that have demanded consistent and more accurate blast results are initiatives to control pit-wall damage to help mine steeper pit slope angles, to control damage to underground opening operating in close vicinity of the open pit mine. Such situation exists at Rampura Agucha open pit lead zinc mine, which is producing 5.7 Mt/a of ore and has started its underground part, which is slated to produce initially 2–2.4 Mt/a and 4.5 Mt/a in the near future. The open pit mine is currently working at 326 m depth and is designed to reach 421 m deep. It has been planned to operate the underground mine maintaining 50 m parting from the planned ultimate level of the open pit mine.Presently, open pit and underground mines are being operated simultaneously. The present average depth of underground working lies between 370 and 410 m below the surface level. Sometimes explosives up to 95 978 kg are being detonated in a blast round in open pit mine. These blasts are often apprehended as a danger to the safety and stability of underground openings. It was decided to document the impact of open pit blasting in the openings of underground workings, so that preventive measures may be taken for the safety and long-term stability of the underground mine. The impact of 86 open pit blasts has been documented in the underground openings and 258 blast vibration data has been recorded. The vibrations were recorded simultaneously in the roof, side walls and at floor levels. The highest levels of vibrations were recorded in the roof and the lowest levels at the corresponding floor levels. The pillars experienced lower level of vibrations than the roof. Blast designs were optimised at open pit mine to control vibration in view of long-term safety and stability of the underground openings. The vibrations generated due to detonation of explosives with shock tubes and electronic delay detonators have been recorded in underground openings for comparative assessment. Ground vibration recorded at roof, pillar and floor were analysed separately and threshold value of the vibration for the safety of underground workings has been determined based on the rock mass rating of the roof rock.CITATION:Singh, P K, Roy, M P, Paswan, R K, Shekhawat, L S and Joshi, A, 2015. Protection of underground mine structures due to adjoining open pit mine blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 279–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The advancements achieved in rapid tunnelling in the 60's and 70's have been notable. It is unfortunate that shaft sinking has not enjoyed equivalent advances and there are many good reasons why this is so. Technical and commercial considerations have held back development and continue to do so despite the increasing urgency in the search for minerals and energy. By the careful selection of an appropri- ate project and the application of specialist engineering the Bdard took advantage of a unique opportunity to apply a mechanised shaft borer in field conditions.

Jan 1, 1981

Misima Mines Pty Ltd (MMPL) operates a large open cut gold mine on Misima Island in the Louisiade Archipelago in Papua New Guinea. Misima Island lies approximately 600 km east-south-east of Port Moresby. The island is 40 km long by 10 km

Jan 1, 1994

By J R. Hernandez-Aguilar, C O. Go, C Acuna

The gas dispersion properties that are the subjects of this communication include three measured parameters, gas superficial velocity (gas rate), gas holdup and bubble size, plus derived parameter, bubble surface area flux. Over the past ten years sensors to measure these parameters have been introduced and those originating from McGill University are briefly described. The sensors have seen extensive use in plant campaigns and experiences on four cell types at three sites are discussed. The impact of frother in controlling bubble size by retarding coalescence is illustrated, introducing the need to understand chemistry/machine interactions in interpreting gas dispersion results. An increase in Sauter mean bubble size (D32) with superficial gas velocity (gas rate, Jg) was found, which followed the empirical relationship where Do ~ 0.5 - 0.6 mm and C and n are fitted parameters dependent on the system (machine and chemistry). Following this trend in Db - Jg, consistent bubble surface area flux (Sb) - Jg trends are also observed. The trend in Sauter mean versus number mean (D10) is used to help interpret the nature of the distribution; as the means approach numerically, the distribution is narrowing. Analysing gas holdup versus gas rate shows both a dependence on location in the cell as well as cell position in a bank, factors which must be accounted for when comparing data from different plants and circuits. The instrumentation and methodologies being developed are presenting new opportunities for incorporating cell hydrodynamics into metallurgical diagnostics. A case study at one plant serves as illustration.

Jan 1, 2005

By Linge H. G

The effect of sodium pyrophosphate and several polyacrylate deflocculants (Freevis 502, 528, 529 and 532; and Maxfloc 1015) on the gold loading on Calgon GRC22 and Norit R035l5 carbons was tested and found to be insignificant in a pulp free enviroument. These deflocculants can therefore be used in plants processing viscous gold pulps without fear of fouling the carbon.

Jan 1, 1990

By A Gray

Physical separation features in almost every mineral processing circuit. The category encompasses a broad range of techniques and technologies including hydrocyclones, gravity concentration methods (including jigs, spirals, centrifugal concentrators, tables, heavy media separators) and thickeners, all of which make use of the inherent density differences between two mediums. It is also possible to include flotation, magnetic separation, and ore sorting in the physical separation category.However, opportunities for enhanced physical separation performance can now go beyond the common practice of optimising unit operations. Improved options exist for feed preparation ahead of the physical separation stage, enabling higher performance and lower cost outcomes for physical separation flow sheets and technologies.The use of new applications in breakage technologies combined with mineral liberation analysis to optimise liberation prior to the physical separation stage provides options for preconcentration and gangue rejection as well as better separation efficiency. The use of low cost gangue rejection and preconcentration can be an intermediate step between mining and processing that allows processing of lower cut-off grades from the mine whilst delivering higher grades to the mill.Optimising flow sheets and technology performance requires detailed understanding of particle size and shape distributions as well as liberation characteristics to suit the particular separation unit, combined with knowledge of the available technologies, their capabilities and the economic impact across the whole mine cycle.CITATION:Gray, A, 2017. The role of liberation in physical separation techniques, in Proceedings MetPlant 2017, pp 147–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By C J. Larder, S E. Turner

The concept of underground grinding is not new, but to a metallurgist and a mining engineer this could be considered unconventional. The idea of pumping a ground slurry several hundred metres from underground in a single lift could also be considered to present a daunting engineering challenge. Using a practical example of a mine in Australia where the owners have requested not to be identified, this paper challenges the conventional thoughts on these concepts and shows that with basic sound engineering practices the production of a ground slurry from underground could potentially provide significant operating cost savings. The supply of ore from the underground mine is currently drawn from depths approaching 800 m below the surface. The cost of hauling the ore to the existing underground crushing station located 500 m below surface has been steadily increasing. A number of alternatives to reduce the mining and processing unit operating costs were examined by Sinclair Knight Merz (SKM) and the mining company. The most radical of these is the use of hydraulic hoisting of ore at an increased production rate. Numerous questions were asked, such as: How does one get a SAG mill or an HPGR crusher underground? Where does one locate a grinding mill underground? Does the technology exist to pump the slurry to surface in a single lift? What will be the cost benefits? What are the risks involved? The study covered the two main technical issues underlying the potential benefits. Firstly, technical evaluations were undertaken on the pumping technology currently available for single and multiple lifts to surface. Secondly, the issues relating to the feasibility of delivering and locating a SAG mill underground were reviewed. Although the capital costs for this project are significant, the operating cost savings showed a potential payback period of less than two years, and furthermore provide the basis for an increased mine life, especially at lower metal prices.

Jan 1, 2005

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By M Scamardella

The CSA Mine is located at Cobar, New South Wales, where it was in continuous operation from 1966 to the time it went into receivership on 29 January 1998. When it closed it was under the ownership of Golden Shamrock. Glencore International, in conjunction with Mt Lyell Mining, undertook a due diligence study to determine the feasibility to re-open the mine. This envisaged operating CSA Mine as a low-cost, copper concentrate producer under the direction of Cobar Management Pty Ltd (CMPL). The new workforce would consist of contractor trades people in operating functions under the co-ordination of CMPL staff, both on the surface and underground. This was the key to establishing the new culture in the workforce. The orebodies at CSA Mine are steeply dipping with copper-lead-zinc mineralisation in zones of strong alterations in a fine-grained siltstone host sequence. The predominant economic minerals are chalcopyrite, sphalerite and galena. The major gauge minerals are pyrrhotite, pyrite, chlorite, sericite and quartz. Ore for the project is being developed and mined from two high grade copper lenses within the QTS North system. Chalcopyrite occurs in two forms. The first consists of coarse chalcopyrite grains in association with pyrrhotite or pyrite. The second form consists of chalcopyrite grains intergrown with pyrrhotite grains. This form of chalcopyrite is quite rare. It allows electrochemical interactions between grains, resulting in rapid oxidation of the chalcopyrite surface. Physically this ore looks like, and has been mistaken for æpeacock oreÆ, ie bornite, but is infact oxidised chalcopyrite.

Jan 1, 2000

By R Verreet

In April 2000 Mount Isa Mines installed hoist ropes of a new design on the double-drum winder at their P49 shaft. The ropes, CASAR Duroplast, were about three times as expensive as the previously used triangular strand ropes. The P49 shaft is situated at Mount Isa MinesÆ George Fisher Mine, located some 30 km north of Mt Isa. This shaft used the tried and proven 6 x 33 triangular strand style ropes. The rope life attained by these ropes at the time was acceptable due to many years of satisfactory performance. The following study indicates the improvement of service life using CASAR Duroplast rope in P 49 shaft, which depends on shaft and winder parameters of that particular shaft and cannot necessarily be generalised to other shafts.

Jan 1, 2005

With the continued implementation of stricter limitations on the discharge of excess process water from all existing and future mining and metallurgical operations, the design and operation of the entire process water circuit must form an integral part of any total operational package. It is far better to æanticipate and circumvent the problemÆ rather than be forced into an expensive remediation program after the event. By far the greatest problem relates to the treatment and disposal of what is generically known as acid drainage. In simple terms, an acidic metal sulfate solution is generated by a series of chemical and biological reactions as soon as most sulfide minerals are exposed to air and water. Treatment of this solution by one or more of a wide range of chemical and physical options can involve substantial capital and operating costs, although there are recent processing options that yield saleable by-products, thereby reducing the financial liability of what is effectively a waste stream. This presentation provides an overview of the Australian situation compared with the rest of the world and outlines the basic features of a number of the more advanced passive and active acid drainage options.

Jan 1, 2004