Search Documents

In conjunction with a study on wear of drag bits the effect of clearance angle on penetration rate was studied.Increases in clearance angle from 24 1/2 up to 30° gave an increase in penetration rate. Thereafter the rate was apparently affected by partial clogging with cuttings.Analysis of results was by a linear regression model and the t-test was applied to assess the significance of parameters in the penetration equation.

Jan 1, 1969

Since the last occasion on which I spoke to you on this subject there has been a considerable increase in the mechanical ventilation of Western Australian mines.The following table compares the figures for 1939 with those of 1941. The type of fan most commonly used is the limit load fan. On account of its higher mechanical efficiency it has very largely superseded the multivane fan with forward curved blades.Two fans of the propeller type are in use and these have given very satisfactory service. This type of fan also has a high mechanical efficiency particularly at the correct duty for maximum efficiency.The maximum efficiencies obtainable from the various types are, for "multivane" 670/0, for "limit load" 75%, and' for aerovane 7810/0.References to propeller fans with variable pitch have appeared in the technical press, but no detailed d~scription has been issued. The advantages of these fans for mine ventilation are not obvious. An aeroplane is required to operate over a wide range of duties, while the speed of the motor for maximum efficiency is pl'actically constant. In such circumstances the propeller can be adapted to the particular work it has to do by varying the pitch of the blades. In a mine the speed of the fan can be varied to suit.the conditions, and it would appear that variable pitch is not necessary while there is a reasonable range of fans to choose from.The question of the correct position for the fan still comes in for considerable discussion. Exhausting fans at the surface have the support of time and custom, and in many cases this represents the only reasonable arrangement. Such fans should be fitted with an evase, especially in the case of fans with a high outlet velocity such as the aerovane types.It is claimed that there are advantages in having the fan at the surface where it is readily available for inspection and maintenance. Experience has shown that these advantages are more apparent than real. Fans will run for long periods with no attention other than occasional greasing and cleaning, and modern electric motors will run without attention for very long periods.In some instances the expense of a power cable to take current to the fan may be saved by placing it on the surface, but in the majority of cases...

Jan 1, 1941

By Pinghui J

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By E R. Ramanaidou, C Tessarolo, M Verrall

Garnierite mineralogy in saprolitic ore of the Goro lateritic nickel deposit, New Caledonia , was investigated using X-ray diffraction (XRD), optical and scanning electron microscopy (SEM) and electron microprobe (EMP) analyses. These conspicuously, green-coloured phases occur either as submillimetre to centimetresized veins or as æbookletsÆ arranged in, macroscopic (subcentimetre sized), accordionlike structures supported in an undifferentiated matrix of mixed ÿ7+ and ÿ10+ phases. Within the veins, nickel for Mg solid solution increased from ten wt per cent NiO at the edge to 34 wt per cent NiO at the core, with vein edges comprising Ni-kerolite with <1.5 Ni per formula unit (pfu) grading to pimelite containing >1.5 Ni pfu at vein cores. The æbookletsÆ comprised nTpouite of formula, (Mg0.67Ni1.59Fe3+0.05)(Si2.17Al0.22)O5(OH)4 and averaged 30 per cent NiO. SEM element mapping highlighted the distribution and mineralogical association of Ni and Mg and emphasised the inverse relationship between Ni and Mg at the macroscopic (thin-section) scale. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Q Qian, M Karakus, J Wang, N Melkoumian, D Goodchild, Q Sui, C Wang

Probabilistic analysis is widely used in slope stability assessment because of its capability to take into account uncertainties associated with geotechnical parameters. There are, however, still many unresolved practical issues to the application of the method. One of these issues is the integration of assessments when multiple sets of fractures are considered for the entire slope. In the present study, this issue is addressed within the framework of Monte Carlo simulation. Probability of failure for pairs of fracture sets are assessed independently and the final assessment of the probability of failure for the entire slope is done using conditional probabilities. Prominent Hill open pit, in particular, the problematic fresh Bulldog shale formation, was used as a case study to test the method proposed. The SWEDGE program of the RocScience software package was used for the analysis.

Sep 26, 2011

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

Most coal mines in Chongqing Area are highly gassy mines and liable to outburst of coal cnd methane. In order to harness mine environment and raise the Prodction capacity, methane predrainage is generally taken as a main preventive measure against outburst by all mines. In the recent ten years, the drainage volume per year has increased from 38.25 million m3 to mote than 100 million m3 with a volume over 12 m3 per tome of coal. In some mines, the draining rate is approaching to 50 percent, the rate in mining districts is up to 60 to 70 percent. The predrainage volume accounts for one fourth of total drainage volume. All these have effectively prevented the occurrence of coal and methane outbursts.This is the current situation of methane predrainage in coal mines in Chongqing area, the methods of predrainage to prevent outbursts and related parametres comprise:1. methods, technologies, supervision and effect of predrainage in different geological and mining conditions,2. the change of methane parametres pre-and post-drainage and the analysis of the effect of methane predrainage to prevent outbursts, and3. ways to improve the effect of methane predrainage.Thus the safety, reliability and production of Changqing Coal Mines will be enhanced.

Jan 1, 1991

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By Askew JE

The large, massive low grade gold orebody at Mount Charlotte has demanded an innovative approach to mining engineering. In the last five years several advances occurred in the areas of rock mechanics, mass blasting, blasthole drilling and truck haulage.Successive crown pillar failures throughout the life of the mine had resulted in a continuous geotechnical program, mostly utilisingconsultants. The culmination of this workwas the development of a successful crown pillar support system. Several stopes have incorporated the technique and the most notable success has been the relatively large F3 crown pillar.In hole hammer drilling was introduced to the mine in 1979, but little work had been done to develop a blasting system to suit the 165mm diameter holes. A non-electric sequential blasting system was adapted for use at themine and up to 600,000 tonnes have been fired successfully in an individual blast. Problems with ground vibration were addressed although this work remains incomplete.

Jan 1, 1984

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

By Brady KT, Pattenden G

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1984

By Beattie T. A

The ability of explosives to fragment rock has been assessed in small scale trials at the Granite Rock quarry, Baimsdale, Victoria. Three 65 mm diameter holes were fired simultaneously in a five metre bench, and the rock collected, screened and weighed. The mass of fines increased as the explosive strength increased in the series 30(10 ANFOPS

Jan 1, 1990

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

By D Craw, J Youngson

Recent exploration for mesothermal gold deposits in the Otago Schist has focussed largely on extensions of, or analogies to, the reverse fault-hosted Hyde-Macraes Shear Zone deposit. Abundant normal fault-hosted mesothermal and epithermal vein deposits in the Otago Schist have attracted less attention, largely because they have limited lateral extent and steeper dips. Northwest-striking normal fault-hosted vein sets near Barewood and Hindon in east Otago crosscut schist foliation on the Barewood-Hindon plateau at a high angle along a combined strike length in excess of 20 kilometres. The trend of the vein sets is not linear, but rather contains several right lateral steps. Almost all veins dip steeply to the northeast. Angular discordance between schist foliation and the plateau surface along the trend increases from near zero at the northwest end of the veins to about 30¦ at the southeast end. Crude formation depth estimates decrease from about 7.5 km at the Barewood end of the zone to

Jan 1, 2002

By Sibson RH

The gold province of Otago occupies an area of upwarped basement, the Otago Schist, comprising predominantly quartzofeldspathic and volcanogenic metasediments. This assemblage is the product of collisional tectonic deformation and associated metamorphism, mainly to lower greenschist facies, during the Rangitata Orogeny (200-100 Ma). Historically this region has produced 240 tonnes of gold, 4% (10 t.) of which was from the mining of Cretaceous gold- quartz mineralised vein systems. Auriferous vein systems in the Otago Schist are mainly hosted within NW trending normal fault-fracture arrays, however NW trending reverse fault-hosted vein systems also occur. We propose that the Late Cretaceous-mid Tertiary Otago Schist structure represents a regional anticlinorium containing flexural folds of at least two wavelengths. The anticlinorium structure has been quantified by determining variations in angular discordance between schistosity and the Otago Peneplain, a Late Cretaceous-mid Tertiary erosion surface covering most of the Otago district. A structural model for the evolution of the post-collisional anticlinorium requires the cooling surficial zone (carapace) of a retrograding metamorphic belt to behave as an elastic lid. Erosion of topographic load on the carapace drove isostatic uplift, which was greatest in the tectonically thickened core of the orogen. In this way differential uplift produced flexural deformation in the elastic carapace, expressed as a large scale arching of the orogenic belt. Flexure created tangential longitudinal strains in the outer-arc, leading to extension and the formation of mineralised normal faults. These structures are separated by a neutral surface from shortening and associated mineralised reverse faults in the inner-arc. Our structural model predicts that the distribution of auriferous lodes should be localised about zones of maximum flexural curvature, where the tangential longitudinal strains are highest. As a result, NW-SE hinge regions separating schistosity dip domains in the Otago gold province may have new found significance as potential exploration targets.

Jan 1, 1995

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Q Liu

Open stoping is one of the widely adopted methods in underground bulk mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sublevel in the ore zone and blasted ring by ring into a stope for excavation. A mass stope blast may involve blasting rock from multi-level drift rounds and displacing the muck to specific locations in order to allow safe and easy access for ore removal. This paper presents a strategic mass stope blast that took place at a large lead and zinc underground mine in eastern Canada. The blast consisted of more than 800 holes drilled in six blocks from three different sublevels. The challenge lay in the control of ground vibration and muck movement using precise timing to complete the blasting within 6.5 seconds. During this time span, sufficient voids were created in each level to allow the muck to move from the upper to the lower levels in sequential order across the six mining blocks without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement as well as the application of electronic detonators. These detonators provided the means to accomplish the desired firing sequence including a drop raise blast at the start of the mass blast. The modelling concept is also described in the paper.

Jan 1, 2005

Reliable predictions of the long-term water quality and water level fluctuations in a final void are vital if mine operators propose to decommission final voids in open cut mining operations. The catchments feeding final voids typically comprise a large proportion of coal placed or re-shaped spoil piles. Spoil piles from open cut coal mining operations have distinctive hydrological characteristics, which result in unique run-off behaviour. There is a need to understand the nature of spoil hydrology processes in order to predict the long-term hydrological behaviour and water quality responses of such systems. Preliminary estimates indicate that it may take 20 or more years for a void to flood. It is impractical for mine owners and operators to wait until long-term hydrological and water quality conditions have been established in a void, before reaching agreement with regulators about mine closure conditions. Reliable simulation of the long-term water quality and water level fluctuations in a void are therefore. The adoption of an agreed modelling approach and sharing of results from field data programs could result in the establishment of a database that could be used, with regulatory approval, for assigning parameter values, without the need for a specific data collection program for every individual void. Industry and regulators should agree on the model adopted for predicting post-closure behaviour of spoil/void systems. This will require reliable, robust methods for field data collection. This paper describes the field monitoring, data collection, model preparation and simulations undertaken over a three year period for Australian Coal Association Research Projects (ACARP) Project C7007. It presents the findings of that research, and provides comment on aspects of the project that were undertaken well and on aspects that could have been done better. Limited data is presented in this paper due to confidentiality arrangements with the relevant mine sites.

Jan 1, 2003

Near-Infrared Spectroscopy (NIRS) Sorting in the Upgrading and Processing of Skorpion Non-Sulfide Zinc Ore In 2008 Anglo American sponsored a research project at RWTH Aachen University to assess the feasibility of the use of near-infrared spectroscopy (NIRS) for ore waste discrimination at the Skorpion zinc mine. The Skorpion mine is an open pit zinc mine located in Namibia, owned by Anglo American with an annual production of 150 000 t/a of super high grade pure zinc. Opportunities for the implementation of NIRS sorting for the Skorpion process exist to upgrade currently subeconomic material, including the marginal dump (over 2000 000 tonnes, av grade of 2.5 per cent Zn). NIRS sorting is not yet implemented or established in the minerals industry however it is a proven technology in the plastics recycling industry, where more than 2000 NIRS sorters have already been installed. NIRS sorting, a type of sensor-based sorting, is a single particle sorting technique which classifies the particles based on the absorbed/reflected radiation in the near-infrared (NIR) region. A disadvantage of NIRS is that it is a surface measurement technique, but NIRS sorting shows overall great potential for the minerals industry. Skorpion ore minerals include zinc bearing phases such as sauconite, hemimorphite, smithsonite, and hydrozincite. These display diagnostic responses in the near-infrared. There are three major absorption features that characterise the reflectance spectra of the ore bearing minerals. These are due to OH and H2O molecular bonds. The spectral response of the waste material is caused by other minerals such as non-zinc-bearing clay minerals, calcite and impure quartz. Test work showed that it is theoretically possible to separate ore material from most waste material based on spectral response in the NIR region. In addition to upgrading material by removal of waste it is also potentially feasible to classify the material based on zinc grade. A tentative correlation between zinc grade and spectral response seems to exist for the sample test suite in the NIR region.

Sep 13, 2010

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987