Search Documents

By Samyguin VD, Filippov LO

The aim of this paper is to emphasise the importance of knowing of the rate of the elementary flotation acts (EFA) - attachment and detachment. By studying the simplest linear model notion of the column flotation, the results of the nonlinear simulaton of flotation separation in the column with lengthwise upward mixing show two principal different types of separative mass-transfer in the column. The first is, the case of a small EFA intensity, almost without the detachment. The second is, the case of a big EFA rate, when the process is close to a local attachment-detachment equilibrium. There is also an attempt to estimate the EFA rate for three different kinds of quartz particles, floated by cation collector in the laboratory column apparatus.

Jan 1, 1993

The Significance of Internal Recycle in Froth Flotation

Sep 13, 2010

Computer simulation of the control systems for the heavy media coal washing process have been presented in this paper. The simulation model applies the Simulink module of the Matlab 5.1 software package and allows monitoring of variations of a

Jan 1, 1998

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Read T. A

PART 1The quantity of dust present and the methods used for suppression of dust in metalliferous mines has, in recent years, received considerable attention from mining engmeers in various parts of the world. Shortly after the publication of the General Report of the Miners' Phthisis Prevention Committee, South Africa, in 1916, the officers of the Broken Hill South Limited started investigations into the conditions of the dustiness of the air in the underground workings. As the methods used are not generally known in Australia, the writers are of the opinion that the present is an opportune time to place them before members of the Institute. A large amount of the subject matter of this paper has been drawn from the 1916 and 1919 reports of the Miners' Phthisis Prevention Committee, South Africa, the paper of Mr. Innes published in "The Chemical, Metallurgical and Mining Society of South Mrica"; also various articles appearing in the Journal of Industrial Hygiene, and the American Journal of Public Health. A great deal of research work into the cause, prevention and estimation of mine dust has been made by the Miners' Phthisis Prevention Committee of South Africa, and officials of the United States Bureau of Mines. The writers considered it advisable to begin the investigation at the South Mine with apparatus and methods developed by the South African Committee.Through the Australian agent of the Cape Explosives Company, inquiries were made preliminary to procuring the necessary apparatus for the determination of dust, from South Africa. The writers then learned that the older gravimetric method used by the Phthisis Prevention Committee was likely to be superseded by the konimeter...

Jan 1, 1922

By S Williams

The primary objective of most mining projects is to maximise the value delivered to the companyÆs shareholders. Achieving best practice performance and maintaining competitive advantage through low-cost production and high productivity is essential to achieving this aim. Benchmarking is an essential tool for the identification and implementation of best practice performance, and to realise continuous improvement by ensuring best practice becomes common practice. But to be successful, that is to deliver long-term value creation, benchmarking must be holistic and align operational performance with strategic intent. This paper outlines a rigorous and structured approach on how to conduct a successful benchmarking program that aligns operational performance with the businessÆs goals. Further it investigates the benefits that benchmarking can provide throughout the project life cycle and provides some key learnings from some of the worldÆs leading miners.

Jan 1, 2009

By Han Kook-Nam, Lawson F

The recoveries of the three cobalt minerals in the Mount Cobalt deposit, cobaltite CoAsS, erythrite CO3(AS04)8H20, and new cobalt mineral with a composition approximating 2CoO.CaO.Fe203.2As205.11H2O were investigated using physical and surface-chemical processes.Over 80 per cent cobalt recovery was achieved by tabling a cobaltite-mineralized sample, while about 76 per cent cobalt recovery was obtained by dry feed magnetic separation of a sample containing erythrite and the new cobalt mineral. The resultant primary magnetic concentrate with a cobalt grade of 5.5 per cent, was able to be upgraded to 14.4 per cent cobalt by regrinding .and a further magnetic separation.Electrophoretic mobility - pH responses for each of the three cobalt minerals were found to be similar. Each mineral remained negative over the pH range 3 to 11 and was most negative at mildly alkaline pH values.Cobaltite was floated effectively with amyl and ethyl xanthate collectors under acidic conditions at collector concentrations of 10-2M to 10-5M. Erythrite showed a similar flotation response using 10-sM amyl xanthate. The practical application of these laboratory separations to an industrial process is suggested.

Jan 1, 1976

Brunswick Mine, one of the largest underground zinc mines in the world, is scheduled to close in 2010 after almost half a century of production. All mines eventually close; some suddenly as a result of unsustainable economic or technical conditions and others, as in our case, as a result of the depletion of the orebody. When the mine is the most significant employer and an economic driver in the region, it is key that the closure is handled in a planned, communicated, well-executed fashion. The following paper documents strategies, plans and activities that are currently taking place in order to ensure a seamless closure that satisfies all stakeholders including employees, management, regulatory bodies and the public. It is an important deliverable for the company that the good will, credibility and reputation that has been built up over the years is sustained throughout the closure process and beyond. A life of mine labour agreement with the unionised workforce, staff retention and recruiting programs, regulatory closure plans, communications and transition adjustment activities will be discussed. The use of a stage-gate style project management tool analysing the risks and key deliverables will be highlighted. It is hoped that the concepts and approaches discussed here may be of value to other operations that will be faced with closure, and its inherent challenges, in the not too distant future.

Jan 1, 2006

In-stope long hole drilling (face parallel drilling) is a new technology currently being applied to shallow dipping (

Jan 1, 2003

By M Lewis, A Cook

This paper is based on the technology and functionality of a Modular Mining IntelliMINE« system which is a real-time decision-making tool. The IntelliMINE« system, incorporating Dispatch, is a fully Integrated Mine Management System. Measuring, quantifying and analysing the performance of mining is considered a fundamental and strategic step towards changing the nature of technical and operational decision-making at the majority of international mining corporations. Successful implementation of electronic data capture devices and computerised tools have enabled many mining operations to improve their competitive position with an improvement in the utilisation of the key assets, mineral resources, capital mining equipment and human resources. Real Time Mine Management Systems are designed to direct the emphasis away from collecting data and focus decision makers on the real issues with well-presented and reliable information. The systems provide a common stream of information to enable senior management, operations, maintenance, technical and process plant staff to make complementary decisions based on reliable, accurate and timely data. The mine asset information tools focus all employees on performance and give them feedback on their area of responsibility. The resulting tangible benefits can be delivered in different forms depending on the mining method, ore type, workplace culture and the current competitive position. Typical areas of improvement reported by system users are:reduction in capital expenditure on mining equipment fleets; more effective planning and budgeting parameters and procedures; increased control over ore-extraction and processing; increased employee accountability and organisational performance; and improved co-ordination between planning, operations, maintenance and processing. These improvements can be delivered in different forms depending on the status of the mine and commodity markets. In times of market oversupply and low commodity prices, the benefits can be delivered to the bottom line in terms of reduced cash costs, reduced capital and operating resources to maintain constant production. In times of market expansion, existing capital resources will be more productive delivering increased production and revenue. Mine management systems have the potential to transform a traditional mine operation into a learning organisation with an improved understanding of the critical performance issues and enable development of relevant strategies to continually identify and eliminate operational inefficiencies. The effectiveness of each strategy and operational change can be accurately monitored and its success (or otherwise) will be quantified. The latest downturn in the world metal prices has forced many mining companies to focus on cost reduction and productivity improvements as a means of remaining competitive. Maintenance represents a significant proportion of the overall operating costs in the mining industry. A structured proactive maintenance approach such as Reliability Centered Maintenance (RCM) can achieve significant cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled, thereby reducing costs and interruptions to production.

Jan 1, 2000

By Clifford C. E

The Black Star and Racecourse orebodies below 15 level contain a major portion of the primary silver-lead-zinc ore reserves of 56 million tonnes at 150 g/t Ag, 6.4% Pb and 6.5% Zn at Isa Mine. Extraction from this area is scheduled to begin in the early 1980's. Mining in this block will be quite com- plicated as the ore is contained in a dozen separate orebodies varying in width from 3 m to 20 m with only narrow barren pillars between them in some cases. Mining objectives which consider metal recovery, costs, environmental and safety factors, operating requirements and rock mechanics are used to compare proposals. The planning work involved in formulating mining proposals considers disposition of reserves, scheduling factors, sequence of extraction, extraction methods, haulage set-up and ventilation requirements.

Jan 1, 1979

By Hughson B

The need to prevent the sterilisation of coal stems directly from the fact that it is a non-renewable resource. In N.S.W. a vast amount of coal resource is located under major public utilities such as freeways, railways, stored waters, pipelines carrying gas, water and sewage, and transmission lines. Total extraction has occurred under freeways, transmission lines and pipelines with little or no damage. Where damage has resulted, the cost of restoration was only a small fraction of the value of the coal recovered. However, coal at present is being sterilised and perhaps lost for ever under stored waters and railways. If engineering solutions are available for mining under these improvements economically and with maximum safety, then coal should be extracted and utilised to the benefit of the State.

Jan 1, 1986

By F Wu, H Wang, W Chen

A pressurisation method with multiparallel fans has been adopted at HongLiuLin Coalmine to control the significant external air leakage through the goaf area of coalface 15207. Potential damaging effects of large external air leakage on a coalmine’s ventilation system are analysed according to the current air leakage status caused by the exploitation of shallow-covered coal seams. The use of pressure balanced ventilation to prevent external air leakage through goaf areas is introduced. The calculation of ventilation network of HongLiuLin Coalmine shows that the air resistance of an external air leakage branch through a goaf area and the air pressure drops from the intake slope to the working face can be adopted to determine the values of pressure to be increased by regulating fans and airflow controlling parameters of regulators. By investigating airflow requirements of the pressure-balanced area as well as the performances of the auxiliary fans currently used in the coalmine, the number of pressurisation fans needed is fixed. The expected result is achieved after the pressurisation method has been carried out, which can be helpful for other coalmines to handle similar problems.CITATION:Wu, F, Chen, W and Wang, H, 2015. Multiparallel fan method to prevent significant external air leakages through a goaf area of a shallow covered coalmine, in Proceedings The Australian Mine Ventilation Conference, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Zhou A, Cadogan J. M

Direct reduction of iron ore (DR) is one of the promising technology emerging in the world's steel industry. Kinetics and Mossbauer studies of DR with hydrogen have been carried out at two temperatures of 600¦C and 800¦C in this investigation. The results show that different controlling steps govern the reduction rate at different temperatures. The mechanism was also found to vary during the reduction. The Mossbauer spectra of the samples reduced in various time intervals were studied to determine the phase changes during reduction.

Jan 1, 1997

By Reilly L, Worner H. K

The EnvIRONment process has been developed to treat steel works dust and organic wastes simultaneously. A pelletised feed is fed into a special DC electric furnace, the pellets becoming immersed in a molten slag above a carbon saturated bath. The iron oxide in the pellets is reduced and carburised whilst the organics are broken down to carbon monoxide, carbon dioxide, hydrogen and water vapour. Volatile metals are vapourised and collected in the baghouse. Over two years of trials in a 100 kg DC electric are furnace has brought the process to the stage where it is ready for commercialisation.

Jan 1, 1995

By A Struminski

The principles of occupational risk evaluation resulting from the improper ventilation of the underground mines were presented. It was shown that the risk level implies the appropriate planning and usage of prevention methods. That approach is fundamental in the ventilation, fire and climate safety management in the copper ore mines. The paper uses the adequately modified Risk Score method.

Jan 1, 2003

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

By J Jeffrey, G W. Wilson, L Gilbert, C

Prior to the commencement of mining, the acid rock drainage (ARD) potential of the waste rock to be produced by an open cut mining operation is assessed by a variety of techniques carried out on drill-hole samples. These include, among others, acid base accounting (ABA), net acid generation (NAG) testing, and kinetic testing. Based on the results obtained, a strategy for the identification, separation and selective placement of waste rock having different potentials to form ARD is developed. During the course of mining, the waste rock classification scheme will be re-assessed periodically to confirm that it is appropriate. This re-evaluation may result in a change in classification scheme, and waste rock dump samples may be obtained for ARD assay purposes to confirm the appropriateness of the revised scheme. The paper describes the evolution over time of the scheme used to classify waste rock at a major open pit gold operation in New South Wales, Australia, including the development of a hydrological model. To confirm the appropriateness of the revised scheme, ARD assay testing was carried out on drill-hole samples collected from dumps having different ARD potential designations, including Non-Acid Forming (NAF), Potentially Acid Forming (PAF), and Low Grade Ore stockpiles. The results of the ARD assay testing and water quality monitoring confirmed the appropriateness of the ARD potential designations and the revised classification scheme, which has been adopted.

Jan 1, 2003

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By T D. H McGrath, W P. Staunton

Benchmarking, comparing an operation or process with the industry standard, is known to be a useful method for identifying plant optimisation opportunities, and in many cases providing the pathway to realise the benefits. The difficulty is generating the database of plant data necessary for a benchmarking exercise. Larger companies can benchmark internally; this option is not available to smaller companies, and the full value can only be realised with a comprehensive “industry wide” approach.The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has undertaken several comprehensive metallurgical industry surveys in the gold industry over the last two decades. Analysis of these surveys has demonstrated areas where many operations can benefit from re-assessment of their operating practices.This paper will review the work undertaken by the Group in this area, in particular the 1999 surveys of gold companies in the Australasian region, and the 2012 international survey of the industry. The challenges of, and opportunities arising from these surveys will be discussed. Some of the highlights from analysis of these databases will be presented as well as noting changes in processing practices observed by the Group over the last 20 years.CITATION:McGrath, T D H and Staunton, W P, 2018. Keeping up with the Joneses – the value of industry surveys and benchmarking, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 509–516 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018