Search Documents

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

By Glastras M. V

The presence of arsenic in solutions which result from the processing of many sulphide minerals leads to a need to understand its speciation in aqueous systems and the reactions of those various species. This paper deals in particular with the precipitation of arsenic from aqueous solution in the form of insoluble inorganic compounds in order to remove arsenic from various hydrometallurgical process streams. The solubility and stability of the precipitates is examined. It has been found that many of the arsenic compounds presently used are more soluble than previously accepted and unstable in disposal sites such as tailings ponds.

Jan 1, 1987

By E Werner, B R. Leavitt

The chemistry of acidic mine drainage discharging from flooded coal mines is commonly reported to improve with time after flooding. This investigation describes a 18-year dataset of post-flooding water chemistry for a below-drainage underground coal mine within the northern Pittsburgh coal basin (Pennsylvania, USA). The Montour mine is a 5650-hectare below-drainage coal mine of maximum 260 metres depth. Montour was closed in 1980 and flooded to within 38 metres of land surface within 4.8 years. Pumping averaging 210 L/s was then employed to maintain water levels at this elevation. The flooded proportion of the mine (by volume) at full flooding was 56 per cent. The shaft where water was pumped from Montour for water control is located about 70 per cent of the distance between the mine water table and the back of the mine ù that is, it is close to the back of the mine. The residence time (total water volume at flooding divided by pumping rate for control) is estimated at 5.6 years. Time series of chemical analyses show three phases of chemical behavior in post-flooding discharge. In Phase I (zero to two years after flooding), iron concentrations were high and reached their maximum (1100 mg/L). In Phase II (two to four years after flooding), a transition was begun to alkaline conditions, with decline in iron and other solutes. In Phase III (>4 years), net alkaline conditions began, with iron concentrations declining exponentially to 50 per cent of mined volume. This attainment of net alkalinity in this case may have also depended on abundant calcite in overburden extended up to 30 m above the mine floor.

Jan 1, 2003

By Wickham P

Digital computer based control systems are used to implement control and monitoring over most unit operations in Mount Isa Mines Limited lead-zinc concentrator and copper concentrator. Implementation has been gradually devel- oped and expanded since the first process computer installation in 1969. Operations currently using high level control logic include crushing, grinding, on-stream analysis of flotation products, flotation reagent additions, and tailings thickening. Details of gains in metallurgical efficiency for each system are considered.

Jan 1, 1978

It is suggested that if adequate knowledge is available about classifiers in closed grinding circuits, these units may be used as on-stream size analysers when equipped with suitable sensing devices. Research work which is at present in progress to enable a hydrocyclone to be used for this purpose is discussed.

Jan 1, 1967

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

There are a number of examples of how environmental factors have been integrated into the water management aspects of mining projects. The Kingston Lignite project in South Australia, Pine Creek Gold Mine in the Northern Territory, gravel and sand extraction from the Nepean River flood plain near Penrith, and the Olympic Dam Project have all illustrated that consideration of environmental factors can be integrated with project developments, with beneficial outcomes for both the project and the environment.Each of the above cases demonstrated an individually significant environmental issue, directly related to the interaction between the proposed project and its environment. In each case, careful research and an integrated approach to the problem resulted in a solution that gave both maximum protection to the environment and optimum consideration to the economic feasibility and success of the proposed project.The solutions ranged from alternative mining methods and improved waste and water management through to the ultimate objective of converting a mining project into a major water-based recreation source. These examples have set a precedent that will contribute ignificantly to the successful development of future projects.

Jan 1, 1988

By B Brattli

The dispersion pattern of heavy metals in soil and water is a consequence of complex geophysical and geochemical processes. Metal release from mining sites and subsequent migration occur primarily through acid mine drainage and erosion of waste and tailings dumps. Water plays a significant role in heavy metal mobilisation. Whilst it acts as a storage buffer for the pollutants, it is also the medium in which most of the reactions take place, and is undoubtedly the most significant transport vector in the pollution process. The intrinsic properties of the acidic drainage such as chemical composition, speciation of key mineral components, redox potential and pH are master variables controlling metal release, transport, deposition, reactivity and availability to biota. The mobility of heavy metals is strongly increased by acidification from acid mine drainage, and the discharge of these metals into the receiving waters results in numerous physical, chemical and biological responses in which the environment can affect the metal and vice versa. The result is an overwhelming number of association/dissociation, substitution, adsorption/desorption reactions, giving rise to a complex migration pattern. The attempt to understand and describe the dispersion pattern of heavy metals is complicated by the nature and level of interaction between the geochemical and hydrodynamic processes that generate and control the movement of the pollutants in the geosphere. Transport models which can be used to predict the behaviour of metal pollutants in a natural environment are still in the initial phases of development and their application to real life situations is limited. The Biochemical Cycle adds another dimension to the mobility of heavy metals. Metals form an important component of the food chain for man and plants. Biological uptake of metals from the bedrock and soil by organisms can result in migration paths very difficult to follow. Biodegradation or assimilation is just a tip of the iceberg.

Jan 1, 2003

By D P. Telionis, P P. Vlachos, R-H Yoon

Industrial processes involving multi-phase flows such as flotation require understanding of the relationships between bubbles, solid particles and the flow. Modern experimental tools are employed in this effort to measure with great accuracy the basic features of the motion of all three phases in turbulent flow. We employed a unique digital particle image velocimeter (DPIV) that can record with great accuracy and kHz temporal resolution, velocity vectors of all three phases, namely the fluid, the solid particles and the air bubbles. The interaction of these three phases was studied in homogeneous isotropic turbulence generated by cylindrical grids. Particles and bubbles were released into the turbulence and the motions of the three phases were monitored. The experimental results obtained in the present work were compared with the predictions of the models published in the literature.

Jan 1, 2005

By Wright G. N

Curragh Queensland Mining Limited, a co-venture of Australian and overseas interests, operates an open cut coal mine 13 km north of the township of Blackwater in Central Queensland, refer attached location map.

Jan 1, 1992

By Hall J. S, Zuiderwyk M, Reid A. F

A prototype version of a computer controll- ed on-line scanning electron microscope image analyser, employing the real-time signals ob tamed by digital control of the electron beam has been used to obtain statistical quantificat lion of a wide range of mineral grain character istics, including composition, size distribut- ion, and degree of liberation. These propert lies have been determined for suites of whole particles of flotation concentrates, mounted without further preparation. The facility is also well adapted to the measurement of general Istereological parameters. The computer control software is based on an operating system which includes the device drivers and which is linked to FORTRAN programs [containing the procedural algorithms. The beam scanner provides a 4000 x 4000 point raster swept at a 10 Mhz rate in steps of 1 to 200 points and a set of up to 8 signal channels which respond to electron or energy dispersive X-ray signals to provide a digital attern.characterizing the sample composition. the beam is stepped at high speed until a part- 'cle or phase boundary is encountered; a longer well time is set if X-ray data is required. he digital scanner interrupts the computer

Jan 1, 1977

Synthetic hollow microspheres have demonstrated reliable sensitization and detonation characteristics in industrial explosives for almost two decades. During that time, water gel formulations and use conditions have changed. The introduction of emulsion explosives has also dictated technical improvements in microsphere sensitizers. In contrast to microspheres, gassing or other sensitizing techniques often cannot satisfy the manufacturing and blasting characteristics required of today's explosives. This paper discusses the sensitizing properties of microspheres, formulating guidelines and quality considerations. Packaging, sampling, transfer, metering, mixing and pumping information is also provided.

Jan 1, 1990

The limitations of the conventional practices, and their effects, in prospecting for and in the evaluation of alluvial gold deposits are briefly reviewed. Geophysical prospecting methods have demonstrated their complementary role in the delineation of deposits by reducing the number of boreholes which are primarily of a 'probing' type. Larger diameter boreholes, although more expensive on a linear basis, are much cheaper on a volume recovered basis. The need to have sufficient volume as well as number of samples is stressed. Classical statistical methods are not appropriate for such deposits as there is sufficient structure, or spatial correlation, to require the application of geostatistics. Quite reliable semi-variograms, but not in all cases, of the spherical scheme have been obtained. Subsequent kriging has, to date, been confined to unworked deposits: retrospective estimates to compare to production have not therefore been produced. However, the technique shows promise but indicates a considerably greater borehole density (of the conventional diameter) may be necessary to produce confident estimates. Used in conjunction with larger diameter boreholes, a lesser borehole density may be sufficient, through radical reductions of the sampling error.

Jan 1, 1977

Powercoal Pty Ltd operates eight underground coal mines in New South Wales and produces coal for both domestic power stations and the export market. Approximately 40% of total production is from continuous miners. Over the past five years, place change mining methods have been introduced to improve productivity from continuous miners. This has involved utilising the existing coal clearance system from the continuous miner to the ratio feeder using trailing cable shuttle cars.By late 1996 average productivity at Cooranbong Colliery using this system had plateaued at 800 tonnes per eight hour shift. A number of factors were identified to increase average productivity to 1500 tonnes per eight hour shift. An improved coal clearance system was one of the factors identified.

Jan 1, 1998

By R Gaze, J Horton

Block models generated with all linear interpolation algorithms contain inherent smoothing that typically results in an underestimation of grades and overestimation of tonnes in resource estimates. For mineral deposits that are anticipated to be exploited by underground mining methods excessive smoothing may result in materially misleading estimates of Ore Reserves. To account for smoothing in the open pit mining environment recoverable reserve techniques such as indicator kriging and uniform conditioning are employed to provide non-spatially located proportions of the large blocks above the cut-off grade. These models are not suitable for underground mine planning where the actual location of material above cut-off is required to design its extraction. To correct for excessive smoothing it is proposed to modify the ordinary kriged block estimates a posteriori using an affine correction with a local variance adjustment factor. The proposed methodology is demonstrated for a base metal deposit during a feasibility study.

Jan 1, 2009

By P Hagan, S Campbell

A study was undertaken using various methodologies to determine the optimum loading and hauling configuration for different haul routes at Callide Mine, a coal mine located in central Queensland. The study involved development of an effective flat haul model that was used to estimate production rates in truck and shovel circuits that employ two excavators of differing capacities then Queuing Theory to construct a capacity constraint model for scheduling purposes to assist in truck allocation and finally a cost model to determine the most cost effective fleet configuration.The model was calibrated using haul road design and performance data of trucks and excavators currently in use at the mine. The study examined the effects of cycle time for different truck and excavator fleet configurations on production rate and costs.The study found haulage cost was directly related to cycle time while production rate reduced with cycle time. The study indicates the approach taken in combining a cost model with a capacity constraint model offers a simple and effective method of scheduling an optimum number of trucks in a haulage circuit.CITATION:Campbell, S and Hagan, P, 2012. Selection of an optimum truck and shovel fleet based on effective flat haul and capacity constraint modelling, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 19-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

This paper examines the interplay between longwall support design/geometry features, operational controls and geological features on ground response. Experience from several investigations is used to demonstrate the influence of factors such as longwall support capacity and geometry, setting pressure, coal seam strength and stiffness, tip-to-face distance and hydraulic supply and control system parameters on longwall ground response. These factors are then used to outline the requirements on key controls such as retreat rate and cutting height and their influence on allowable roof convergence. The ground response curve concept as a means to provide graphical representation of longwall support and strata interaction processes is presented. The approach was developed to address the requirement for a practical longwall support evaluation and selection tool that can take account of support load influences such as changes in roof geology or cover depth. An example of the comparison between single pass longwall and top coal caving in a thick seam environment is given to demonstrate the influence of the various factors discussed.

Jan 1, 2005

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By W Angerer

This paper describes the design of the marine riser structures, including the design measures for sealing and protection from flooding, dewatering and connection to the main tunnels, for the Gold Coast desalination plant in Queensland. The risers connect the intake and discharge tunnels to the ocean. Construction commenced on both in April 2007. The paper describes the key design criteria for the risers, the construction constraints that influenced the design and the design of the main elements of the risers and the connections to the tunnels.

Jan 1, 2008

By G M. Evans, C M. Phan

This paper presents an analysis on the dynamic adsorption of frothers and collectors onto air bubbles in flotation. The analysis was carried out using the theory on the surfactant transfer by diffusion and adsorption. The bubble size was considered when solving the diffusion equation for the dynamic surface excess. The adsorption kinetics was modelled employing the Langmuir adsorption isotherm and its extension with the inclusion of the lateral interaction of the adsorbed molecules (the Frumkin adsorption isotherm). The numerical computation was applied to solve the governing equations. The dynamic adsorption of the surfactants was measured in terms of the dynamic surface tension for sodium dodecylbenzene sulfonate (SDBS) and Dowfroth 250, using pendant bubble tensiometry. The results show that for air bubbles with diameter of the order of 1 mm, the bubble size effect on the dynamic surface tension is small and the solution of the diffusion equation for a planar gas-liquid surface can be used to describe the dynamic adsorption onto the air bubbles. The experimental data obtained with SDBS were well described by the Frumkin adsorption isotherm and the molecular diffusion. The model description for the experimental data obtained with Dowfroth 250 required the kinetic equations. The paper is relevant for further analysis of the role of the adsorbed surfactants in the particle collection.

Jan 1, 2005