Search Documents

By R Austerberry, S Green

The discovery of the Cuffley Lode at Mandalay Resources Costerfield Operations provided an opportunity to extend mine life via mining the offset depth extension of the previously worked Alison Mine. Access from the existing Augusta Mine placed the initial Cuffley underground workings at approximately 250 metres depth from surface. As the new orebody transitioned towards production, a secondary means of egress needed to be established. The depth of the initial capital development presented a challenge in establishing a secondary means of egress that could be confidently relied on. The availability of land to locate a surface shaft collar further reduced available options and geotechnical drilling further limited suitable shaft locations. Time limiting factors such as permitting and having a secondary means of egress in as soon as possible, further highlighted that an innovative secondary means of egress was needed. A consideration of using an emergency gig lowered by a suitable sized crane supplied by an external crane contractor was investigated and found to be a suitable outcome. This Emergency Gig was deployed via the Cuffley Return Air Raise. When trialled, the emergency gig was found to provide a reliable, repeatable extraction method with an acceptable level of risk. Issues discovered during such trials further improved the process to a point where this extraction method became the adopted secondary means of egress for additional lodes that existed at depth. When assessing possible methods of secondary means of egress, the use of a third-party crane and custom designed and fabricated emergency gig should not be discounted. Where a crane can be sourced within an acceptable timeframe, the emergency gig extraction method provides a reliable safe and cost-effective means of secondary means of egress, especially when multiple shafts are to be developed. Local laws may negate the ability to employ such a system, although it is believed with good communication and well-constructed risk assessments, this system can be safely deployed.

Mar 15, 2021

By E Jak, M Shevchenko, D Shishin

One of the key aspects to develop sustainable metallurgical production is to ensure that the predictive power of thermodynamic tools is brought up to a new level of accuracy and reliability. Exploring new polymetallic processes, integrating primary and recycled materials, means utilising the uncharted areas within the Cu-Pb-Zn-Fe-Ca-Al-Mg-Si-O (major) – Cr-Na (slagging) – As-Sn-Sb- Bi-Ag-Au-Ni-Co (minor) slag-solids-metal-matte-speiss-sulfate system. This requires extensive integrated experimental and thermodynamic modelling study, which is underway at PyroSearch at the University of Queensland (UQ).

Aug 21, 2024

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Consultants in the mining industry have the opportunity to visit interesting deposits all over the world. Each deposit has its own set of challenges to face when it comes to defining and understanding the deposit geology and the economics to make it viable for extraction. Some of the challenges can include appropriate data capture, sampling techniques, structural characteristics, geochemistry, geophysics, lithology definition, and economic boundaries. It is essential that the practices used at each deposit (eg drilling, sampling, geological modelling, resource estimation etc) are documented and the results obtained are robust and defensible. The Competent Person is not always aware of instances where their resource estimation practices have not been substantiated. ‘You don’t know what you don’t know’ is a phrase frequently used during a mineral resource audit. Technical work to substantiate drilling, sampling, density, assaying, geological modelling and estimation processes is not always completed. Audited Competent Persons often comment: • ‘I was unaware that this was required.’ • ‘I have not had training in this area and do not know how to complete the checks required.’ • ‘This is how we’ve always done it.’ Examples of audits where it was found that geological practices were not substantiated are examined here. A discussion is included on why substantiation of these practices is important, and potential reasons as to why there are instances of unsubstantiated processes and practices are discussed.

Mar 22, 2022

By G Tranell, E Pastor-Vallés, A Vallejo-Olivares, J B. Pettersen

Metals are essential for the sustainability transition and decarbonisation of society. Yet, it will be paramount to produce them sustainably and minimise the affiliated resource and energy use and the associated emissions. In the circular economy, the metallurgical industry should recycle existing material stocks, and improve its utilisation of wastes, residues and side streams. This increases the complexity of processes, as they become both (often multi-fraction) waste treatment as well as material production processes and brings complexity to the assessment of environmental benefits. Assessing the environmental impact of technological developments frequently is supported by life cycle assessment (LCA). While the method is well documented, its implementation involves several methodological choices that deserve reasoning and analysis, such as how to define the product when former wastes are turned into new products, the selection of impact methodology when converting emissions to environmental indicators, the definition of system boundaries and co-product allocation and the interpretation of sensitivity and uncertainty in final outcomes. In this exploratory study, we investigate how the variation of LCA set-up affects the environmental burden of the system. We consider a metallurgical process where a mix of hard-to-recycle aluminium-containing streams is used to produce aluminium cast alloys in a rotary furnace. Remelting with salt-fluxes allows recovering metals from partly oxidised/contaminated streams, such as dross, bottom ash and industrial shavings, but at the expense of generating significant amounts of salt-slag/salt-cake hazardous waste. The study considers different system alternatives such as landfilling the salt-slag residues versus valourising them into salts, aluminium concentrates, ammonium sulfate and non-metallic-compounds to be used by the metallurgical, construction or chemical industries. Practical recommendations are outlined to facilitate the implementation of LCA in assessing the potential benefits of the circular economy in the metallurgical sector.

Aug 21, 2024

By A Coelho, D Bruce, H Grosser, C Parken, M Xia

Carrapateena is a new underground sublevel cave mine and was officially opened in 2020. It has a mine life of 20 years. Development began in 2016, and with the rare opportunity to start a with a blank canvas and having a long mine life, an effort was made to explore how to incorporate innovative and leading-edge technologies. The Ventilation on Demand (VoD) system was designed with the objective to optimise power consumption and ventilation delivery through the primary and secondary ventilation systems. Primary fans controlled by Variable Speed Drives (VSDs) and dualwinding secondary fans with multiple setpoints control the delivery of overall quantity. Automated butterfly dampeners control the regulation of air to individual production crosscuts, and automated louvres control the exhaust quantities from the mining levels. Ultra-sonic flow sensors are installed to measure air quantity and environmental stations are installed to measure air quality. Both are designed to play a key role in control and calibration of the system. It was quickly identified that no one vendor could provide a holistic solution to meet the design requirements. A strategy was derived to use multiple vendors, harnessing the specific strengths of each. A control system has been developed to allow the Site Operations Control Centre (SOCC) to oversee and control real-time delivery of ventilation as required by operations. The first full level installation of the VoD system was completed in September 2020.

Mar 15, 2021

By Q Shu, T Deng, B Yan, B Song, D Wang

In view of the lack of phase equilibria data of vanadium-bearing oxide system and the desirability of them for design or optimisation of vanadium extraction process, the phase equilibria relationships of V2O3-FeO-SiO2-CaO(15 mass per cent) system were determined experimentally and then an isothermal section phase diagram of this system was constructed. Totally, 81 samples of different composition were equilibrated at 1623 K for 48 hours in iron crucible under Ar atmosphere. The equilibrated samples were quenched quickly in cold water, and then the phase constituents of all the samples were identified by X-ray diffraction (XRD) combined with electron probe microanalysis (EPMA) measurements.

Aug 21, 2024

By S Sineva, E Jak, M Shevchenko, D Shishin

This study represents a part of comprehensive research aimed at integrating nickel into a thermodynamic database constantly developed at Pyrosearch. The behaviour of Ni in calcium-ferrite slags is considered. An integrated approach combining experimental and thermodynamic modelling methods has been employed to predict phase equilibria in the NiO-CaO-FeO-Fe2O3 system under oxidising conditions and in equilibrium with the metal FeNi phase. The compositions of liquid slags and coexisting solid solutions have been determined through the analysis of equilibrated and quenched samples by electron probe microanalysis technique (EPMA). The research results are presented in the form of liquidus projections on the corresponding phase diagrams, considering both oxidising and reducing conditions. The solubility of Ni in spinel, dicalcium ferrite and calcium oxide as well as solubility of Fe and Ca in Ni monoxide, have been examined under several atmospheric conditions. Additionally, the compositions of the NiO-FeO monoxide in equilibrium with metal phase have been studied. The experimental data not only support the outcomes of thermodynamic modelling but also validate the parameters of the applied thermodynamic models, thus confirming the reliability and accuracy of the integrated approach.

Aug 21, 2024

By D Reid, J Vinod, M Rahman, A Fourie, T Vo, J Ayala, A Russell

This paper reports on an industry and Australian Research Council funded research project, TAILLIQ, that is a joint initiative between four Australian Universities. The paper discusses the accuracy with which the critical void ratio can be determined for a given tailings; it does this by presenting the results from a ‘round robin’ study in which 18 geotechnical laboratories around the world participated, testing the same tailings (sampled from a gold mine in Western Australia). The results were variable, although a reasonable number were very similar, as described in the paper. The paper provides additional test data for sandy silt gold tailings recovered from a sponsor’s site in Australia, including preliminary calibration chamber test data, results from direct simple shear tests and characterisation tests to determine unsaturated geotechnical properties.

Jul 1, 2021

By L Manca, P B. Hills, D Tyler, N Pollington

This paper describes a collaborative project undertaken by Newcrest Mining Limited (Newcrest) and pitt&sherry to identify, develop and then implement global best practices to manage the exposure to inrush (dry and mud) hazards in underground mining operations. An extensive literature review was undertaken to identify past experience globally and the current state of knowledge and practice in managing inrush hazard. A key requirement of the literature review was the development of a list of guiding questions which would form a framework for approaching operators to discuss the topic, capture recent learnings and understand current operating practices to allow the development of a best practice solution. An initial cohort of 14 mines across four continents chose to contribute and detailed interviews were carried out by the project team. The outcome from the literature review, interviews with participating mines and various internal discussions was a comprehensive summary document detailing Basic versus Best Practice management of the inrush hazard. This document is being used as a gap analysis tool by Newcrest to assess and guide the management of inrush hazard at their existing and future operations. The summary document has also been provided to the participating mines for their consideration. The project is iterative and will continue to evolve as new experiences, knowledge and practices come to light.

Mar 15, 2021

By E Villaescusa, A Kusui, R Talebi, R Hassell, C Arcaro

Northern Star Resources (NSR) operates several seismically active mines as part of its Kalgoorlie Operations. In order to successfully continue mining at depth in increasing stress conditions, strategies need to be developed to reduce, control and manage the impact of seismicity causing damage to the rock mass. Consequently, a research partnership was developed with the WA School of Mines (WASM) through Mining3. The main aim of the project was to develop appropriate ground support standards that could withstand the expected dynamic response with minimal to no rehabilitation required for the life of that excavation. The project utilised a design methodology for determining the required energy demand based on detailed geotechnical mapping, probabilistic analysis of wedge formation and an estimate of rock ejection velocity based on uniaxial compressive strength of the intact rock (Villaescusa et al. 2016). The ground support scheme consists of high tensile chain link mesh, resin encapsulated de-coupled posimix bolts and plain strand cable bolts, in one, or multiple passes together with plain shotcrete. Implementation of the design posed several challenges including how to install the chain link mesh, maintaining the required productivity, ensuring quality control, and understanding the interaction of the several ground support components within the scheme. The implementation of the system within a trial area was successful from development mining to open stope extraction. The most significant field verification of the system occurred with near field M+1.9 seismic occurring in proximity to an operating long-hole drill. Despite large displacements exceeding 0.5m in places, there was no significant ejection of rock or failure of the ground support system. Following the successful trial, the ground support design methodology and standards have been implemented across several NSR sites. The system forms the basis for the successful extraction of resources in future high seismic risk areas.

Mar 15, 2021

By T Walton, C Perring, M Pepper, G Gerber

The Yandicoogina Channel Iron Deposit (CID) is an accumulation of iron pisolites cemented by a goethite-rich matrix. The Yandicoogina CID’s are found in a palaeochannel that meanders within a broad structural basin of the Yandicoogina Syncline in Pilbara region of Western Australia. RTIO Yandicoogina Mine Geology team contributed to a number of strategies maximising the iron ore reserves mined by Rio Tinto. Two strategies are discussed: the replacement of the Batter-Berm final pit walls by contour dozing; and upgrading the lower grade material to crusher feed. 1. Contour dozing – traditional Batter-Berm pit final wall configuration left kilometre long wedges of ore sterilised around bench margins. Contour dozing final walls (ie dozing of ore down the ore-waste contact) as internally defined by RTIO Yandicoogina Mine Geology (Mine Geology), enabled recovery of additional crusher feed. 2. Upgrade of lower grade material – the lower ore domain (GVL) within the Yandicoogina orebody contains numerous clay pods. Contaminant Al2O3 inherent within clay pods can result in CID material outside of crusher feed grade specifications, causing it to be flagged as ‘internal waste’ in mining models and permanently lost to waste dumps. In 2011, after multiple tests, Mine Geology demonstrated that this material could be upgraded to crusher feed via wet processing. With the support of the RTIO Metallurgical Development team new grade specifications were defined. The resulting material has been used to supplement higher grade ore. While increasing the mining ore output, these ongoing value-adding strategies also promote more sustainable mining via better use of the non-renewable iron ore commodity. The initiatives extend mine life, reduce waste movement, improve strip ratio and increase productivity

Mar 22, 2022

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By J Player, P Evans, G Sweby

Achieving quick underground access after the completion of an open pit mine can be critical to maintaining project value and ensuring regular ore feed to the mill. This paper outlines the design and construction for two portals in an active open pit to commence underground development quickly whilst installing appropriate ground control to maintain long term access in an uncertain setting. Implementation of the portal designs was complicated by the change in underground design from hangingwall access to footwall access late in the life of the open pit due to preferable ground conditions. The portal locations did not have easy access for ground support installation integrated into the pit design due to the timing of the underground design changes. Practical implementation of the ground support systems subsequently became a key part of the project. Intact rock strength, rock mass characteristics, gradational weathering / alteration profile and structural information were modelled against pit displacement monitoring as the basis from which the portals were located and ground support schemes designed. Conditions around one of the portals necessitated numerical modelling to estimate the appropriate level of ground control for long term stability. The design was completed whilst the open pit was actively on-going and the portal areas not entirely exposed. The rock mass assessment and analysis for the two portals indicated different ground support scheme capacities would be required. The expected level of control for one of the portals also necessitated the use of monitoring with extensometers and load cells to ensure the rock mass response and ground support scheme performed as planned. Construction of the portals demonstrates the benefit of a considered design process, a plan which allows practical installation of ground support schemes where access is limited, the benefit of ongoing monitoring to ensure performance remains within design limits and the challenges involved working within an active pit with limited floor space.

Mar 15, 2021

By M Medina, J Alexander, R J. Longey

Capricorn Copper Pty Ltd (CCPL) are operating the Capricorn Copper Mine located at Gunpowder, Queensland. As current holder of the environmental authority for the site, CCPL have obligations to rehabilitate areas of the mine that are no longer operational and have the potential to cause/contribute to environmental harm. CCPL sought a voluntary Transitional Environmental Program (TEP) to provide an agreed program of works to cap and rehabilitate the former Mammoth Tailings Storage Facility. The voluntary TEP contained conditions that were required to be met, to reduce the potential for environmental harm from the facility. The former Mammoth Tailings Storage Facility commenced use in the early 1970’s, and is an unlined valley in-fill structure, contemporary in design compared with other such approved structures of the era. The decommissioned Mammoth Tailings Storage Facility, now known as the Old Tailings Storage Facility (Old TSF), has been a legacy source of contamination due to the existing capping not meeting modern cover criterion, and allowing oxidisation and infiltration to the underlying acid forming tailings resulting in Acid and Metalliferous Drainage (AMD) from the facility. A cover design for the Old TSF, and other mine waste storages onsite that required clay capping, had been proposed by previous operators. Under the TEP cover design phase, it was identified that a key constraint was the lack of significant quantities of low permeability clay onsite. The lack of available clay prompted the consideration of alternate lining materials for the Old TSF, with a Bituminous Geomembrane Liner (BGM) being adopted as the preferred alternative. The BGM compared favourably with clay-based materials on seepage analysis, and led to other benefits by eliminating the need for borrowing clay off site, reducing the site’s environmental footprint, and reducing construction time. The BGM cover system on the Old TSF is being monitored with the intent to use this as a case study to confirm expected performance, enabling the cover design to potentially be adopted on the remainder of the site’s mine waste storages that require capping.

Jul 1, 2021

By Y Xu, T Rowles, B Dareeju, A Dissanayake

Recent updates on tailings dam design guidelines require analysis of undrained (short-term) stability with the application of the SHANSEP model. The SHANSEP model, which was originally developed for alluvial soils, predicates that the Undrained Shear Strength (Su) increases with increasing effective stress. Residual soils by their nature do not necessarily follow this relationship. This paper examines an alternate method to define Su over a range of effective stress conditions for residual soils. Residual soils, formed by weathering of their parent rocks, are generally micro-structured in nature. The microstructural features, such as interparticle bonding, play a fundamental role in stress-strain behaviour of the residual soils. As interparticle bonding is independent of effective stress and void ratio, the undrained shear strength of residual soils is expected to be less dependent on effective stress than alluvial soils, especially at low stress levels. A series of triaxial tests conducted on residual soils, however, indicated that the undrained shear strength and the undrained shear strength ratio (Su/σv’) are to a degree dependant on effective stress. It was found that the undrained shear strength ratio is significantly higher under low stress levels and progressively reduces with increasing effective stress. Based on the laboratory testing data, a strength function with varying undrained shear strength ratios can be developed for the residual soils under the stress range anticipated for a design of a tailings dam. This includes capping the input undrained strength at lower effective stresses based on the drained (effective) and minimum undrained strength. The Factor of Safety (FOS) calculated for the embankment utilising the traditional limit equilibrium (LE) method indicated the application of undrained strength function for the residual soils can provide a significant optimisation for the embankment design compared to adopting a constant undrained shear strength ratio or constant undrained shear strength in the design.

Jul 1, 2021

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

By W A. Take, M McKellar, A Walsh, S McDougall, S G. Evans

Recent tailings dam failures have heightened public awareness of the hazard posed by storage facilities for mining waste, illustrating the need for a more critical examination of tailings dam breach mechanisms and the potential mobility of liquefied tailings. Knowledge from tailings dam breach studies will help improve safety and risk management through more accurate inundation maps, dam consequence classifications and emergency preparedness plans. Tailings dams differ from conventional water retaining dams, although dam breach relationships used in practice rely heavily on relationships derived for breach processes from the latter. Physical modelling offers a controlled environment to advance the understanding of tailings dam breach processes, thereby allowing for modelling of simple geometry and boundary conditions to test hypotheses. The performed experiments investigate prototypical tailings dam configurations and material behaviour, with the objective of validating numerical models that will enable practitioners to better assess and mitigate tailings flows resulting from tailings dam failures. Research conducted in the Queen’s University Landslide Flume at the Coastal Engineering Laboratory has investigated the breaching of 1 m high dams with tailings geometry by overtopping initiated by a v-notch incised in the dam crest. This paper presents the initial results of the next stage of this research comparing the outflow hydrograph following loss of containment caused by shear failure to overtopping initiated by notch flow. The two dam experiments presented are constructed with similar dam and reservoir geometries allowing for a direct comparison of the effect on the outflow hydrograph of each failure event. Preliminary outcomes suggest that although both dam failure events are triggered from separate mechanisms their geometries allow for similar values of Q_peak to be reached. Future work is currently planned to expand the shear test series to explore the influence of failure mechanism on the outflow hydrograph.

Jul 1, 2021