Search Documents

By R McIlwraith, B Breul

Two case studies are presented in this paper. The first one discusses a roller compacted concrete water supply dam that was constructed in El Mauro in Chile to provide water for agriculture activities downstream of a copper mine during the dry season. The 23 m high dam used a bituminous geomembrane (BGM) as the low permeability upstream facing element on the dam to control seepage through the dam. This is the first time that a BGM has been used in this application. A deep cut-off trench was used to control seepage beneath the dam and through the abutments. This paper briefly presents the design of the dam, including selection of the concrete mix and maximum aggregate size that the use of the Coletanche BGM allowed, and provides details of the construction, quality control and assurance of the installation of the BGM. An ultrasonic apparatus was used as part of the quality control on the BGM seams.The second case study discusses a tailings dam in Cerro Lindo, Peru (near Chincha), where a watertight BGM was installed on the upstream face. Results are presented of the survey done by a consultant on the behaviour of the dam and in particular of the BGM following an earthquake of magnitude 8.1 in Chincha close to the site. These findings on-site were checked by trials in a laboratory in California. Test results are given and explained.CITATION:Breul, B and McIlwraith, R, 2015. Case histories – roller compacted concrete dam waterproofing with a bituminous geomembrane in Chile and a tailings dam in Peru subject to an earthquake of 8.1 magnitude, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 367–372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D A. Williams, P J. Chapman

Constructing upstream raises with tailings is an accepted and cost-effective practice in Western Australia, where the climatic conditions are favourable, desiccation (and hence overconsolidation) occurs rapidly due to air drying and there is a perceived low seismic risk. This is in contrast to many other settings, where there is either a positive water balance, high seismicity or a combination of both. In recent times, there has been an increased focus on seismicity in areas of Australia that have historically been considered to be of low seismic risk. The increased focus is driven by two recently published documents used by tailings practitioners and increased awareness from corporate entities, particularly those with mines in high-seismicity regions such as South-East Asia and South America (particularly Chile).The increased awareness has resulted in increased rigour being applied to seismic design of tailings storage facilities (TSFs) in general, and particularly upstream-raised TSFs. This paper compares the results of a seismic stability assessment for an upstream-raised TSF located in the Goldfields region of Western Australia, which has historically been considered a low seismic area, with a seismic stability assessment carried out for a crossvalley TSF containing similar tailings but located in a high-rainfall, high-seismic setting in South-East Asia. The influence of the adopted design earthquake values on the results of the assessments and the potential impact of the maximum design earthquake (MDE) on the design approach is presented for both cases. The results indicate that although the Western Australian site is located in an area thought to have low seismic risk, the screening level analyses suggest that the MDE could result in liquefaction of the tailings materials. Not surprisingly, liquefaction was also indicated for the South-East Asian site. The outcomes of the assessment are also presented.CITATION:Chapman, P J and Williams, D A, 2015. Seismic design of upstream-raised tailings storage facilities in a semi-arid, low-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 157–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By S Joyce, Z Agioutantis, D van Zyl, D Shields

Over the past 15 years, the mining industry has begun to incorporate the concepts of sustainable development and sustainable mining practice across the life cycle of mineral operations. This requires addressing economic issues, community impacts and concerns and environmental protection, and is captured in part by the phrase ‘design for sustainability’ (McClellan et al, 2009). Over the same period, the industry has seen a gradual decline in ore grades for many mineral commodities. As a result, large volumes of tailings and mine waste rock are being produced around the world, and it is expected that the annual production volumes of these materials will increase, even if there is not a significant change in the demand for materials.Another related thread of change has been the realisation that societies need to move away from linear economies (raw materials, production, consumption, disposal) towards more circular ones. This will help societies become more resource efficient, which is defined by the United Nations Environment Programme as reducing the total environmental impact of the production and consumption of goods and services, from raw material extraction to final use and disposal. The goal is to create more with less and deliver greater value with less input. Circular economies require thinking in terms of the waste hierarchy (reduce, reuse, repurpose, recycle, recover, landfill).The challenge is that the waste hierarchy was originally designed to address embodied mineral content in products rather than mine waste and tailings generation. It will need to be reconsidered in a mine life cycle context, focusing on a value-based conception of waste (Van Ewijk and Stegemann, in press).In parallel to these changes, it has remained an imperative in the mining industry to dispose of these waste materials as economically as possible while protecting the environment. Single handling of these materials has been the main target, which reduces the life cycle costs of their management but may make reuse of waste and tailings technically more difficult or economically infeasible.This presentation explores a rethinking of the large volume earthen material waste issue at mines. The underlying theme is that some or all of these materials can be valuable resources for the future that can positively contribute to sustainable development. These resources can offer economic gains to firms, communities and societies; contribute to environmental well-being; enhance social interactions with the previously mined landscape if handled properly; and, with proper policies in place, reduce governance commitments. Each of these topics will be briefly explored. This will be followed by a discussion of approaches to manage design and operations to allow future resource recovery.CITATION:Van Zyl, D, Shields, D, Agioutantis, Z and Joyce, S, 2015. Waste not, want not – rethinking the tailings and mine waste issue, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D A. Williams, J C. J Boshoff

The properties of tailings that emanate from laterite nickel processing plants are significantly different to most other mine tailings. They typically comprise a mixture of fine materials that are made up of altered clays, chemical residues and salts. Neutralisation processes that are undertaken prior to tailings discharge result in a high proportion of gypsum in the tailings. The salinity of the pore fluid is commonly higher than 140 g/L of salts, dominated by magnesium sulfate. Hydraulically-placed tailings that undergo solar evaporation typically reach dry densities of less than 1 t/m3 of insoluble solids. In situ water contents after many months of drying may be as high as 80 per cent, and peak undrained shear strengths are unlikely to be greater than 20 kPa.This type of material is not conducive to upstream raising, from both a practicality and overall slope stability perspective. Even at rates of rise of less than 1 m/a, it is difficult to effect upstream raising on unaltered laterite nickel tailings. However, the authors have successfully designed and implemented upstream-raised laterite nickel tailings storage facilities. The upstream raises have been formed from both imported natural materials and air-dried and compacted tailings borrowed from the tailings beaches.Drying and associated strength gain has been achieved through various means of mechanical intervention, repeatedly exposing a zone of tailings to the atmosphere for evaporation. Field trials have been undertaken to optimise the approach, and the findings from the trials have been implemented in practice to allow stable upstream raises to be constructed. The cost savings and reduced environmental impact compared to high-volume downstream raises have been significant.CITATION:Williams, D A and Boshoff, J C J, 2015. Upstream raising of laterite nickel tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Bouzalakos, W Timms, H Malli

Combining ultramafic mine tailings and acidic mine drainage via mineral carbonation to sequester carbon dioxide, presents an opportunity to minimise waste on mine sites. Low pH mine water with trace element concentrations can be effectively treated by high magnesium mine tailings, a useful source of finely ground reactive matrix. By using milled tailings for mineral carbonation, there are negligible energy requirements for communition of ore rocks to reduce particle size. This study aimed to assess the technical applicability of reacting ultramafic tailings and acidic mine water through mineral carbonation technology in the mining industry. Dissolution has been identified as the rate limiting stage in mineral carbonation; hence the study focused on identifying optimal dissolution conditions. Ultramafic tailings (particle size <100 µm) derived from serpentinite ore, were reacted with a typical mine water that was synthesised in the laboratory. Through variances in the solid to liquid ratios and temperature of dissolution, a maximum five per cent magnesium dissolution efficiency was reached at 50 g/L and 100°C. The acidic mine water was neutralised (from pH <2 to pH ~6) and iron, copper and zinc ion concentrations reduced significantly during the formation of solid precipitates. Carbonation was undertaken by injecting carbon dioxide into the magnesium-rich solution to form stable carbonates. The experimental work demonstrated proof of concept; however, dissolution efficiency and carbon dioxide sequestration was low, indicating that further research would be required before larger scale implementation.CITATION:Malli, H, Bouzalakos, S and Timms, W, 2015. Ultramafic mine tailings to treat acidic mine water and lock away carbon through mineral carbonation, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 133–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Boshoff

The management and operation of tailings storage facilities (TSFs) are often neglected until the process plant has to shut down as a result of this negligence or as a result of a catastrophic failure as was the case during the recent TSF failure in North America.TSFs are often regarded as non-assets and do not receive the attention they deserve in terms of technical expertise and financial provision. A TSF is not a simple structure but a complex and dynamic structure that changes throughout its operational life. The operational life of a TSF is the period in which there is the greatest opportunity for risks to occur. The failure of a TSF is normally not as a result of a single event but as a result of a consequence of events. These events are often not recognised in time due to a number of factors.Process plants and slurry pumping systems are operated at suboptimal conditions in order to maintain throughput. At the same time, the tailings properties are compromised in terms of slurry density and particle size distribution amongst other things. Tailings deposition cycles and drying cycles are not well understood and the tailings management strategy is not well tuned in terms of maximising consolidation and improving in situ densities. Pond control is also neglected. These are aspects that form the keystone to the effective utilisation of available deposition area as well as the frequency and cost of future embankment raises.Apart from operational issues, forward planning in terms of budget requirements, increases in tailings throughput, embankment raises, pipe replacements, etc are normally put on the back burner. Available deposition space at the time seems to render this planning obsolete.The bottom line is that responsible tailings management and proper forward planning can limit liability and reduce the bottom line in terms of cents per ton if correctly implemented by suitably qualified tailings managers and engineers.The aspects that need to be considered as part of responsible tailings management are highlighted in this paper.CITATION:Boshoff, J, 2015. Responsible tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By P Edmondson, S Narendranathan, S Setchell

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste landform. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using a case study developed at a large iron ore open pit mine in the Pilbara region of Western Australia.CITATION:Narendranathan, S, Lee, E C, Setchell, S and Edmondson, P, 2015. Modelling of an integrated waste storage facility, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Hughes, J Agius, T Ferguson, A Parbhakar-Fox, D Lester, L M. Jackson

Management of historic tailings is a major challenge facing the mining industry and its regulators. However, through improved mineralogical and chemical characterisation of such materials the opportunity to develop better rehabilitation strategies arises. Microanalytical techniques including microscopy, mineral liberation analysis and laser ablation inductively coupled plasma mass spectrometry (ICPMS) allow for improved tailings characterisation – but the challenge posed by these techniques is how to use them effectively. Additionally, data sets collected by such techniques must be properly integrated, only then can they assist in the identification of the most appropriate rehabilitation strategies. A study conducted at the Old Tailings Dam (OTD) located at the Savage River Mine, Tasmania allowed for the integrated use of several microanalytical techniques to help evaluate the benefits of a shallow water cover as a potential rehabilitation strategy. Samples (n = 144) from 14 trenches and 11 boring cores (2 m maximum depth) were collected across the OTD. These were subjected to routine acid-base accounting, with a subset subjected to detailed mineralogy using a modified sulfide alteration index (SAI), X-ray diffractometry and mineral liberation analysis (MLA). In addition, representative samples (n = 6) from across the OTD were subjected to laser-ablation ICPMS to characterise the pyrite chemistry. Our results showed that tailings in the northern area submerged under a natural water cover were relatively unoxidised from approximately 1 m depth, with SAI values of 1 to 2. Tailings from the subaerial southern portion were extensively oxidised to approximately 35 cm depth (SAI = maximum 5.8), with fresher materials observed underneath (SAI = 5 to 5.8). Pyrite from across the OTD is enriched in Co, Cu and Ni. Through the integrated application of microanalytical tools, we determined that establishing a water cover of at least 1.5 m depth across the OTD is a suitable rehabilitation option for this historic site. However, consideration for the reprocessing of these tailings to extract Co should be further investigated.CITATION:Jackson, L M, Parbhakar-Fox, A, Hughes, A, Agius, J, Ferguson, T and Lester, D, 2015. Microanalytical evaluations of the savage river old tailings dam, north-?west Tasmania, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 111–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Reid

Run-out analyses of tailings storage facilities are typically undertaken using methods based on rheological theory. These are reasonable techniques to model the behaviour of tailings that, through significant run-out and possibly mixing with supernatant water, are generally acting in a fluidised manner. Such modelling often follows on from two-dimensional continuum analysis models where, if failure is predicted, grid failure often occurs when deformations begin to increase. This results in a disconnect between the prediction of failure and the modelling of the potential extent of the failure.Recently, rezoning methods have been incorporated into commercially available two-dimensional soil mechanics deformation codes. Rezoning techniques enable large deformations to be modelled within a two-dimensional continuum analysis framework; however, while promising, the use of such tools is not yet widespread, and a consensus is yet to develop on how they should be applied to tailings dam run-out modelling.This paper uses FLAC rezoning techniques to model the flow behaviour of two historic tailings dam failures. The purpose of these analyses is to critically assess the performance of rezoning against some available historic failures. The required data to undertake such an analysis is outlined, along with the inherent limitations and assumptions required. Parametric analyses are outlined to address some of these issues. In general, the analyses undertaken underestimated the flow distance observed in the historic failures by varying degrees; however, in some instances, the analysis reasonably reproduced the qualitative shape of the initial failure zone. A variety of potential reasons for the discrepancy between historical observations and the models undertaken are provided.CITATION:Reid, D, 2015. The use of rezoning techniques to model historic tailings failures, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D R. L Vedoy, L Botha, S P. Gumfekar, J B. P Soares

Most of the known in-place reserves of oil sands are found in Canada. These oil sands ores are mined using various processes to extract bitumen. The by-product slurry resulting from the extraction process, known as tailings, is discharged into tailings ponds. Fine kaolin clays are an important ingredient of the tailings because they remain suspended in water for many years. Current polymeric flocculation/dewatering technologies use acrylamide-based polymers such as polyacrylamide (PAM), but sediments produced using PAM-based flocculants hold considerable amounts of water due to the formation of loosely-packed flocs. Anionic polymers are better flocculants due to bridging and the charge-neutralisation mechanism. In this paper, we will compare the synthesis of two flocculants: thermosensitive, anionic flocculants and thermosensitive, hydrophobically modified anionic flocculants. The first flocculant is a copolymer of acrylic acid (AA) and N-isopropyl acrylamide (NIPAM), in which AA is the anionic monomer. The second flocculant is a copolymer of NIPAM, AA and the hydrophobic monomer N-tert-butyl acrylamide. We evaluated the dewatering efficiency of 2 wt per cent kaolin using both flocculants by comparing settling rates at different flocculant dosages, charge neutralisation ability and supernatant clarity. To better understand floc formation, we measured the floc size formed by both flocculants at different flocculant dosages. We propose that the hydrophobic monomer in the terpolymer flocculant helps expel water out of flocs, ultimately decreasing the water content in the sediments.CITATION:Gumfekar, S P, Vedoy, D R L, Botha, L and Soares, J B P, 2015. Thermosensitive, hydrophobically modified anionic flocculants for dewatering kaolin clays, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 45–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Boshoff, D Reid

It has been recognised worldwide that the liquefaction risk of unconstrained tailings stacks or cyclone underflow embankments requires careful consideration. The stability of a tailings deposit where the perimeter embankments are made up of hydraulic fill is often governed by post-liquefaction stability.Cyclones are frequently used around the world to classify tailings into a coarse underflow for building a tailings impoundment wall and a finer fraction that is disposed of into the basin. The shear strength of the tailings that form the outer embankment of a tailings storage facility (TSF) and the location of the phreatic surface are the two most significant factors influencing the structural integrity of the facility. The coarse underflow is placed in such a way as to contain the overflow, which is finer, has low strength and is often poorly consolidated.A cyclone field trial was undertaken at a gold mine in Western Australia to assess the feasibility of using the cyclone deposition method to optimise and increase the capacity of an existing tailings cell. The aim of the cyclone trial was to collect information to demonstrate to the client and the regulators that cyclone deposition was a feasible option for raising TSF embankments. The cyclone trial provided an opportunity to assess the cyclone under field conditions and the quantity and quality of the underflow fraction produced on-site. A variety of methods were used to assess the flow liquefaction susceptibility of the tailings underflow sample produced during the cyclone field trial.The field trial, laboratory testing and analysis will be discussed in this paper.CITATION:Boshoff, J and Reid, D, 2015. The resistance of cyclone underflow material to flow liquefaction, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B P. Wrench, M J. Gowan, P J. Chapman

Embankment dams constructed mainly of sand or non-plastic fine soils are susceptible to liquefaction, particularly in high-rainfall, high-seismicity environments where there is sufficient water to saturate the materials and sufficient energy from an earthquake to cause liquefaction. This paper shows the process adopted to review the stability of an existing cross-valley, centreline-raised cyclone tailings sand embankment dam.The study showed that two-dimensional stability analyses did not sufficiently capture the potential for instability, overestimating the depth of the critical failure surface. Instead, three-dimensional modelling was required to provide a reasonable representation. Post-liquefaction stability analyses carried out using the three-dimensional model indicated an adequate factor of safety (FoS). The FoS under seismic conditions was still considered to be a concern based on pseudostatic analyses (but noting the limitations of the analysis method).Earthquake-induced settlements were estimated using an empirical approach based on case history records (Swaisgood, 2003). The post-earthquake event settlement was estimated to be in the order of 600 mm, which is considered to be acceptable for the embankment, taking account of the proposed long-term freeboard of more than 8 m under operating conditions and 2 m under the probable maximum flood condition.CITATION:Chapman, P J, Wrench, B P and Gowan, M J, 2015. Review of static and seismic stability of a cross-valley sand tailings embankment in a high-rainfall, high-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By G B. Douglas

Lime-based neutralisation has long been the remediation treatment of choice for acidic mine pit waters. While suited to the attenuation of acidity, lime-based neutralisation may be difficult to implement efficiently due to variation in quality and the partial loss of neutralisation efficiency due to armouring. Large volumes of gypsum-bearing sludge may also require mechanical dewatering and transfer to final voids prior to resumption of in-pit mining or closure. Thus, operational costs may be substantially higher than primary neutralisation alone. Lime production also results in large greenhouse gas (CO2) emissions.Hydrotalcites (HT) are a class of Mg-Al layered double hydroxide minerals with the composition Mg6Al2(CO3 )(OH)16.4H2O. A range of other divalent and trivalent cations may also readily substitute for Mg (eg Cu, Ni, Pb, Zn), Al (eg Fe, La, Ce) and metalloids/oxyanions (SeO42-, AsO43 -/CrO42 -, MnO4-) for CO3 into the hydrotalcite structure. A common feature of acid mine pit waters, often overlooked in assessment of potential remediation options, is the frequent predominance of divalent and trivalent cations as a consequence of partial decomposition of both ore and gangue minerals during in-pit wall rock leaching. Thus, given the presence of substantial divalent and trivalent cations in acidic mine pit waters, an opportunity exists to exploit and in effect work harmoniously with the prevailing pit water composition to form a polymetallic hydrotalcite.The utility of hydrotalcites in the remediation of acidic mine pit waters lies in their ability to incorporate a wide range of contaminants; instantaneous formation, often in a single step; simple post-treatment solute composition; rapid settling; low sludge volume; and the potential to form ore-grade precipitates potentially amendable to reprocessing to (partially) recover remediation costs. Examples of hydrotalcite formation as a method to remediate contaminated acidic mine pit waters at laboratory-scale to full-scale will be presented.CITATION:Douglas, G B, 2015. Whither lime? In situ hydrotalcite precipitation as a method of remediation for acidic mine lakes, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Eschebach, D Mathewson

A belt press filter (BPF) handbook containing practical information for the reference of plant designers and operators has been created as part of Australian Coal Association Research Program project C23040. The handbook combines research and experience with newer generations of equipment and circuitry. BPFs are increasingly finding application in the dewatering of thickener underflow tailings slurries due to changing environmental regulations, difficulty obtaining tailings storage facility approvals and limited water availability. Sources of BPF inefficiency and low availability stem from a lack of understanding of the key operational parameters that affect their performance. This lack of understanding typically leads to increased operational expenditure due to suboptimal reagent dose rates and increased maintenance costs, or decreases in plant availability due to excessively high filter product water contents and equipment failure. It is essential for the continued economically competitive operation of Australian coal handling and preparation plants that complex factors affecting BPF operational performance are clearly defined and understood. Installation and operation handbooks are often provided to sites with new installations, but these manuals are manufacturer- or even model-specific and are often focused on mechanical maintenance. The handbook identifies industry ‘best practice’ and improvements developed by other sites, such as extra spray bars, air system bleed valves, guarding designs, feed and filtrate protection screens and roller tensioning systems. Equations to predict optimum operating conditions – such as free moisture, belt tension and reagent dose rates, with simple feed-specific variable inputs – have been developed from site-specific test work. The correlations developed provide a benchmark for plants to attempt to achieve. This provides operators and process engineers with a tool to explain BPFs and assist them in optimising the performance of BPF dewatering plants of both contemporary and less modern design.CITATION:Mathewson, D and Eschebach, D, 2015. ACARP belt press filter design, operation and maintenance handbook, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R McIlwraith, B Breul

"This paper discusses the successful use of bituminous geomembranes (BGMs) in mining applications since their development in 1974. It explains and illustrates the structure of a BGM composite, which is a geomembrane manufactured by impregnating a polyester geotextile with a compound of bitumen, elastomer and filler. Examples of applications of BGMs in the mining industry are also presented in the following contexts.Storage of solid waste: storage of mining waste at mines in Canada heap leach pads in France, Peru, Chile and Turkey at the base of a mining waste landfill in Brazil capping of solid mining waste in Chile and Canada temporary capping of mining stockpiles in Australia (with possible reuse of the BGM for other works).Examples of the application of BGMs for the storage of liquid waste in mining containment reservoirs in Canada, Guatemala and Peru will also be given.For each example given, reasons are supplied that supported the choice of BGMs by the clients and consultants, drawn from the following advantages of the BGM:BGMs have excellent puncture strength, due to the internal polyester reinforcement, as well as excellent ultraviolet resistance. This often eliminates the need for a cushion geotextile or cover soil over the BGM.BGMs have a very long life expectancy, in excess of 300 years, in subsoil conditions (Breul et al, 2004).BGMs can be installed in very harsh climatic conditions. They are suitable for high wind environments as their heavy mass per square metre makes them resistant to wind uplift. The low coefficient of thermal expansion means that BGMs are suitable for installation in mines where very low or very high temperatures are expected. This reduces construction delays and allows for a quicker use of the mining facility.The fact that the BGM can be installed by the mine’s own workforce, after appropriate training from the BGM manufacturer, allows for a more flexible construction sequence on the mine.Ability of the BGM to connect to other materials such as concrete, steel, rock and other geomembranes that may be on the mine site.The technical advantages of a BGM enabled the engineering consultants to prepare solutions for their mining clients that had a lower environmental risk, had a faster completion schedule and were overall a cheaper option than with a polymeric geomembrane.CITATION:Breul, B and McIlwraith, R, 2015. Bituminous geomembranes in mine construction, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By K Williams, M Pender, T Honeyands, T Krull, D McCallum, R Holmes, R Orense

Bulk cargoes, including iron ore fines, must be shipped according to the rules agreed by the member states of the International Maritime Organization (IMO). One critical safety measure is the transportable moisture limit (T?ML) required for Group A cargoes (cargoes that may liquefy). A number of shipping incidents involving iron ore fines from India, where liquefaction of the cargo was suspected to be the cause, have brought the issue of iron ore fines T?ML into the spotlight. Extensive research has been undertaken by the major iron ore producers from Australia and Brazil to support the IMO in developing regulations for the shipment of iron ore fines. To this end, iron ore companies sponsored the AMIRA P1097 project to establish a modified T?ML test approach specific to iron ore fines. The project was undertaken by TUNRA Bulk Solids, CSIRO’s Centre for Bulk Solids and Particulate Technology and the University of Auckland, with project leadership provided by Creative Process Innovation. This program of work supported test work findings from the IMO Iron Ore Technical Working Group, which reported its findings in September 2013.The purpose of this paper is to present the major research findings from the AMIRA P1097 project, which includes a review of the original T?ML methods, highlights of the research that supported the new iron ore fines T?ML method and an outline of current iron ore T?ML requirements.CITATION:Williams, K, Honeyands, T, Holmes, R, Orense, R, Roberts, A, Pender, M, McCallum, D and Krull, T, 2015. Maritime bulk cargo transportable moisture limit requirements for iron ore shipments, in Proceedings Iron Ore 2015, pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015