Search Documents

By Baker G

The detailed mineral composition of the lead-zinc ores at Captain's Flat was first studied in 1942 (Edwards, 1943).At that time the workings did not extend far below the 750ft. level. Since then development has been extended to the 1,390ft. level, and -at the request of the management of Lake George Mines Ltd., an examination of the ore from the deeper levels has been made as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.This account is. based on that examination (Mineragraphic Rept. No. ,537, C.S.I.R.O.)GENERAL GEOLOGYThe geology of the Lake George Mines has been described briefly in The Geology of Australian Ore Deposits (1953), and in much greater detail in an unpublished report by K. Glasson (1952). The area consists of fossiliferous Upper Ordovician sediments overlain by volcanics (Kohinoor VoJcanics), and by fossiliferous Silurian sediments. The volcanies comprise a series of· flows ranging in' composition from dacite to rhyolite, with interbedded tuft's and shale lenses.The region has been strongly folded. The regional strike is from 340° to 355°, and dips are from 75°W. to 75°E, A major syncline, pitching 200 N., occupies the centre of the area. The Kohinoor Volcanic'l outcrop as two bands which represent the east and west limbs of this syncline.The Volcanks in the western limb, with whIch the orebodies are associated, are more strongly sheared than those in the eastern limb.

Jan 1, 1953

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By Wilson O. A

TABLE OF CONTENTS1. Introductiona. Process Changes since 1939.b. Current Practice.2. Ore Characteristicsa. Copper Minerals.b. Gold Occurrence.3. Treatment of High Grade Acid Orea. The Ore Treatment Planti. Coarse Crushing SectionDust Controlii. The Concentrating MillDesliming SectionGranular GrindingGranular FlotationGranular Flotation ReagentsFlotation MachinesSlime FlotationConcentrate CleaningConcentrate Handlingiii. Scavanging No.1. Mill Granular Tailings at No. 2 MillRegrinding UnitScavenger Flotationb. Pyrite Productioni. Pyrite Flotationii. Pumping of Pyriteiii. Storage of Pyriteiv. Pyrite Loading

Jan 1, 1952

CONTENTSIntroductionGeneral GeologyCoral Reef-Volcanic Set'iesRock TypesMicaceous Sandstone and MudstoneLimestoneVolcanic RocksChertsDepositionDiatremesEarth MovementsRelation of Ore Bodies to StructureINTRODUCTIONThe author encountered the problems discussed in this paper in 1947 while surveying the mining centres of Mungana and Redcap for Broken Hill South Ltd. After his resignation from that company he made a semi-regional survey to investigate the regional problems raised by the preliminary study. Broken Hill South Ltd. continued its studies on the known ore bodies while the author's investigation was going on, and he is indebted to the staff of this company for assistance during his field work.The area mapped is part of a larger area mapped in reconnaissance by the Aerial, Geological and Geophysical Survey of Northern Australia by a party headed by Dr. H. I. Jensen...

Jan 1, 1952

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

Gold in the stibnite veins of Costerfield, Victoria, was described in 1922 1, prior to any mineragraphic examination, as (a) free yellow gold (b) free rusty gold and (c) combined gold. The free yellow gold occurs in quartz and will amalgamate with mercury. The free gold of dull, rusty or copper-red colour occurs in massive stibnite and has been stated to resist amalgamation with mercury. The dull colour is only skin deep and the colour is bright when the rusty gold is scratched. The appearance of the rusty gold is spongy or cellular and it generally occurs near small cavities in the stibnite. The suggestion that the cellular character indicated the removal of a certain amount of stibnite leaving a residue of se.condary gold cannot be sustained.It now appears probable that the rusty gold is formed by the primary dissociation of a gold antimonide and is distinct in origin from the normal yellow gold which is deposited with quartz or stibnite from auriferous mineral solutions.The combined gold referred to in the earlier paper was the gold contained in the stibnite as revealed by assay. Such gold was at first thought to be either dissolved in the stibnite or else present as free interstitial particles too minute for observation in transmitted light in thin sections.Subsequent examination of numerous polished,surfaces disclosed the small particles of gold occurring in the grain boundaries in aggregates of fine grained stibnite 2. The assumption that all the gold in the stibnite, as revealed by assay, occurred in this way is now known to be incorrect, because limited amounts of a gold antimonide have been found in the veins.

Jan 1, 1952

CONTENTS:1. Introduct'iona. Previous Accountsb. Summary of Geologyc. Physiography2. Morgan Groupa. Lithologyb. Structurec. Faulting3. The Mineral Deposita. Descriptioni. Size and Shapeii. Compositioniii. Effects of Oxidationb. Relationship to Structurec. Genesis of Ored. Mount Morgan Orebodye. Sugarloaf Orebody4. Granitea. Mount Morgan Graniteb. Town Granite'c. Moonmera Granite5. Calliungal Beds6. Razorback Beds7. Acknowledgments8. References

Jan 1, 1952

The purpose of this paper is to outline some aspects of the experimental worlr that has been carried out in the mineral dressing laboratory at M'ount. Morgan during recent years.The subject matter has been dealt with under the following headings:1. Comminution of various mill products.2. The application of sulphur dioxide as a flotation reagent.3. Heavy-media separation.4. Bulk flotation of sulphide ores.COMMINUTION OF VARIOUS MILL PRODUCTSThe following data were cbtained by processing fractions of reserve grade ore.Granular TailingIn Table 1 are shown the results of tests on material representative of average grade tailing. In the first test (H1 ) the granular tailing was floated as received and in the second test (Ha) the tailing was ground prior to flotation.

Jan 1, 1952

It is the purpose of this paper to produce some evidence on the accuracy to be expected from normal assay procedure using the usual first class equipment, and to examine the effect that many assaying inaccuracies have on reported metallurgical recoveries.Generally speaking, the evaluation of the gold content of a mineral ore sample by the fire assay method is a relatively simple process.A weighed quantity of finely ground ore is fused with suitable fiuxes including litharge and a reducing agent to give a button of lead and a quantity of slag. The shower of lead produced by the reduction of the added litharge collects the gold and silver present in the ore, concentrating the values into the lead button.The button of lead, after separation from the slag, is, on heating in an absorbent cupel in a current of air, reoxidised to litharge and absorbed into the cupel leaving a gold and silver bead in the cupel. This bead' is heated in a solution of nitric acid to dissolve the silver, leaving the gold undissolved to be dried and weighed. Knowing the original weight of the ore and the weight of the gold prill the value of the ore is easily calculated.Summarising1. Fusion Process.-Ore plus fiuxes give a slag plus lead button.2. Cupellation Process.-Lead button is re-oxidised to litharge leaving a gold and silver bead.

Jan 1, 1952

Kalgoorlie is the main mining centre of the Western Australian Goldfields. Its famous Golden Mile' has been noted for the exceptional width and richness of its goldtelluride lodes. Since the mid-1890s production on the major mines has been maintained practically continuously.Rich ore, though not as plentiful or as rich as formerly, is still (1948) being mined in places. Unexplored areas still remain within the main auriferous belt which offer reasonable chances of success with intensive exploration.Much detailed information has accumulated in recent years through the geological mapping of underground workings by some of the larger mining companies. The purpose of this paper is to correlate observations made in most of the accessible old and recent workings in the mines of the Lake View and Star group and elsewhere.GENERAL GEOLOGYRock TypesThe rock formations are:-1. Fine-grained (older) greenstones, locally referred to as calc schists. There were originally pillow lavas and other flow rocks of basic composition, now extensively chloritised and/or carbonated. Pillows and fragmental flow- tops are recognisable. Intercalated with flows near the top of the series are several beds of sediments.2. Graphitic slates and other more arenaceous sediments.Although referred to as slates, they are rarely more than well-bedded shales with poorly developed fracture cleavage:Thick bands of felsitic rock are found in places.

Jan 1, 1952

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine's history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952

Soon after the Rosebery concentrator commenced operations in 1936, an investigation was begun in an attempt to discover a substitute for cyanide in lead flotation. Cyanide is an excellent depressant for zinc and iron, but it also powerfully depresses the copper, silver and gold bearing minerals present in Rosebery ore, thus allowing them to pass through to the zinc concentrate or final residue where they are of little or no value.The investigation was not entirely successful, but it did indicate that sodium bisulphite or sodium sulphite could be used as a depressant for zinc without depressing the copper, silver and gold bearing minerals. The sulphites were, however, much inferior to cyanide as apyrite depressant.At about this time, I. W. Wark, using the captive bubble technique, had shown that, at the concentrations normally used, sodium aerofloat is not a promoter for pyrite or galena in alkaline solutions (see his book "Principles of Flotation", p. 188). Some preliminary tests on the production of a copper concentrate from Rosebery ore were therefore carried out using sodium sulphite as depressant and sodium aerofloat as promoter.The results of this work were promising but, since Rosebery ore usually carries only about 0·5% copper, there did not seem to be much incentive to carry the work further. With the outbreak of war, however, Australia became desperately short of copper and the relatively small amount in the ore. became of sufficient importance to...

Jan 1, 1952

By Nixon J. C, Reynolds C

Three principal features of the ore at Captain's Flat, New South Wales, tend to complicate concentration of the valuable minerals, these being:1. The ore occurs in three more or less separate bodies which vary in texture and mineral ratios. Mining of constant proportions of the three sections, or adequate blending of the ore, is not fully effective, and consequently the flotation section is subjected to feedof varying texture.2. The mineral association in the heavily pyritic ore is extremely intimate. Composite particles exist even at 20 micron sizeI, and probably finer.3. The copper content of the ore averages_about 0,6%, which is high enough to justify recovery of the chalcopyrite in a separate concentrate. A review of the metallurgical history of the mine shows that this feature has been the cause of the several major changes in flowsheet of the flotation section since the commencement of milling.METALLURGICAL HISTORYThe mine started production in January 1939, at the rate of 250 tons per day of sulphide ore, assaying 0·68% Cu, 6·52% Pb, 10·8% Zn, and about 1 dwt. Au and 2 oz. Ag per ton.

Jan 1, 1952

Accident prevention in industry is a task as important to the ultimate result of an undertaking as efficient machines, good tools or trained operatives. In fact, like many qther phases of industry today, "Accident Prevention" or "Safety Organisation" has developed in this century, to a degree that is now acknowledged as an integral part of industrial thought and planning. This has not always been the case, as the following snap-shot picture of the past illustrates.The Broken Hill Proprietary Company recently celebrated at Whyalla the Jubilee of the opening of the Iron Knob Tramway. On that occasion a dinner was tendered to the pioneers, and in talking to the Writer of the early days one of the old gentlemen present could not refrain from recounting some of the accidents he had seen or experienced.Several such incidents were recounted at length, after each, the old fellow would say, "An' there weren't no safety officers or compensation in them days".The Broken Hill Proprietary Company Limited was a pioneer of safety in Australian industry and considerable success has followed its activity in this connection; the accident rate of the steel industry now compares satisfactorily with that of any other industrial undertaking. A measure of 'the success of the safety organisation, is, that in recent years, despite extensive construction programmes at various centres, and despite a heavy labour turnover, a decreasing accident rate has been maintained. This success, in the Writer's opinion, arises from the fact that by its early attention to plant protection, the introduction of safety standards and further through the interest and energy of departmental superintendents and foremen, the...

Jan 1, 1951

The first difficulty encount.ered in preparing this paper was to find a definition of the word "special" as applied to steel. The first thought is "obviously any grade not mild steel" but this is an over-simplification, because the term "mild steel" covers a series of carbon ranges, each found from experience to be especially suited to the production of a particular rolled section.Even if the Australian structural mild steels are excluded it is found that no part of the plant here is independent of special steel.The face-man on Iron Monarch makes his bench safe by barring down with a 0.6% carbon steel bar. He bores a hole into the ironstone with a 0.75-0.8% carbon steel drill, driven by a jackhammer which is built of a variety of special steels. After it is shot down, the stone is lifted by an electric shovel, very few of whose steel components fall into the general category of structural grades of mild steel.Further special steels are met with in the truck into which the stone is loaded, the hauling electric locomotive, and the rails on which these .run. Even the permanent way uses more than one grade, e.g., the crossings experiencing heavy service have their frogs built with austenitic manganese steel inserts.Special steels play their part in the overhead crane which tips these trucks, and in the crushers into which they discharge, and so they can be followed right through the production line, and they are still there at the seaward end of the ship loading boom at the head of the WhyalIa ore jetty.

Jan 1, 1951

By Finlayson J. F

The advantages of rapid and accurate analyses are becoming appreciated in many industries today and have resulted in a great increase in the number of samples received by their laboratories. This has caused some firms to consider the installation of one or more of the instruments available for analytical chemistry. In this country there are relatively few people with experience of instrumental methods and it is difficult for a firm considering the installation of such equipment to assess the advantages which instruments may give them, and to decide which instruments, if any, will be of most use to them. The object of this paper is to give a brief survey of instrumental methods in the field of inorganic analysis. Instrumental methods of analysis have numerous advantages when used correctly. They enable extremely rapid analyses to be made in many cases, e.g., analysis of refined lead by purely chemical means takes about two days whereas spectographically the analysis can be completed in approximately one and a half hours. The accuracy ofinstrumental methods, generally between 1 and 5%, is higher than most chemical methods for small percentages of impurities. Furthermore, if the instrument can be calibrated against absolute standards the errors are usually random and not biased to one side of the correct result. The sensitivity is high, enabling in many cases the detection and determination of smaller percentages than can be detected chemically. This high sensitivity enables and, in some cases, requires the use of very small samples, and results in considerable savings in reagents, allowing the analysis of considerably more samples without undue loss...

Jan 1, 1951

This paper is based on studies made intermittently from 1937 to 1950. Its object is to describe the surface geology and the tin lodes, and to relate the lodes to the structure of the field.PREVIOUS REFERENCESR L. Jack made his first report on the field in 1880, but his principal report was made in 1883. W. E. Cameron described the Great Northern lodes in 1904. Numerous later reports on various mines were made by L. C. Ball, J. H. Reid and C. C. Morton, the most important of which were on the Black King, Good Friday, St. Patrick and the Great Northern Gully Shaft.GENERAL GEOLOGYJensen maps the Herberton area as part of a granite massif intruding rocks of two ages, the Younger Metamorphics of Silurian-Devonian age, and the Older Metamorphics of Older Palaeozoic age. The distinction is apparently based on lithological data. The Older Metamorphic rocks occur as inliers in the granite massif to the west and east of Herberton (Fig. 1).The area described consists of granite traversed by numerous dykes. West of the area, approaching the Older Metamorphic rocks, the granite becomes finer grained as if chilled towards its contact, and the dykes more numerous. To the east, passing from the Nova Scotia mine to Mount Lavery there are numerous dyke rocks, but the outcrops are poor and knowledge of the geology indefinite. The area is the main tin-producing area. To the west there are comparatively small tin lodes in the granite, and the "Copper Firing Line" occurs in the Older Metamorphic...

Jan 1, 1951

Investigations of the Mineragraphic Section; Commonwealth Scientific and Industrial Research Organisation, have included most of the known stannite-bearing ores in Australia, and have revealed several new occurrences of this relatively uncommon mineral. They provide information about its paragenesis, and its possible effect on tin recovery, that may be of general interest.Several of the investigations used in the preparation of this paper, were made in the first instance by pr. F. L. Stillwell or in collaboration with him.CASSITERITE-SULPHIDE ORES IN NORTH-WEST- TASMANIA Stannite is a minor component of most of the cassiterite sulphide ores of north-western Tasmania. These include the orebodies of Mount Bischoff, the Cleveland mine, Moina, the Stanley River district, Renison Bell, and the Heemskirk-Zeehan district, and form a well defined metallogenetic provence which is related to the Devonian granites of this part of Tasmania.In these ores mineralisation began. with deposition of cassiterite, a little wolfram, and quartz, topaz and tourmaline. With falling temperature, deposition of cassiterite ceased and arsenopy-rite, pyrite, and especially pyrrhotite, formed in abundance, tending to give massive sulphide ore. A little chalcopyrite; stannite, sphalerite and native bismuth accompanied the pyrrhotite. Deposition of quartz ceased after the pyrrhotite, was formed, and the later-formed nonsulphide gangue consists chiefly of carbonates and fluorite. With, the advent of the carbonates the pyrrhotite was altered to fine-gained intergrowths of marcasite and pyrite. Excess iron from the pyrrhotite entered the intergrown carbonate, or was precipitated as magnetite. Some solution of the cassiterite occurred at this stage, the tin being redeposited chiefly as stimnite replacement rims around the residual cassitellrite grains. Varying, but small, amounts of sphalerite, galena, tetrahedrite and silver minerals were depoSited at this stage, bringing the mineralisation to a...

Jan 1, 1951

It is proposed to deal with those raw materials which are produced in South Australia to meet the needs of the country's steel industry. They are chiefly, iron ore, limestone and quartz.Iron ore and limestone are fed to the blast furnaces of Newcastle and Port Kembla together with coke to produce the hot metal charge for the open hearth steel furnaces.They are also qsed in the raw state in the steel furnaces to assist in the conversion of the hot metal to steel. The iron ore is quarried from' Iron Knob and shipped from Whyalla to Newcastle and Port Kembla, whilst the limestone is supplied from the deposits at Rapid Bay and shipped in the same manner.Quartz is used in the manufacture of ferro-silicon, an alloy which is added to the ladles of molten metal tapped from the open hearth furnace in the case of almost every grade of steel. It is obtained from a quarry situated between Iron Knob and Whyalla, and shipped to Newcastle.IRON OREWith the exception of several small quarries situated at Breadalbane, Cadia, Cowra, Crookwell, Michelago, Jerrawa and lerraama in New South Wales, the iron ore requirements of Australia's steel industry to date have been met from Iron Knob and the Middleback Range in South Australia.Several of the small deposits in New South Wales were worked during the war years of 1941-44 during the shipping emergency and produced 1,355,417 tons, compared with an output of approximately 43,000,000 tons from Iron Knob between 1901 and 1949.

Jan 1, 1951

In recent years a large amount of work has been done at various plants overseas, and also at Broken Hill Associated Smelters, Port Pirie, South Australia, on the use of Dwight Lloyd sintering plant gases for sulphuric acid manufacture by the contact process.Several plants have modified their sintering machines and operating procedure, and some have adopted gas recirculation techniques, to obtain a relatively high proportion of the sintering plant gas at an S02 concentration acceptable to a contact acid plant 1.These adaptations were investigated at Port Pirie, and it was found that gases of suitable S02 concentration could be obtained. The results justified installation of a contact acid plant and a decision was accordingly made in 1949 to construct such a plant.However, the local conditions presented some difficulties not generally encountered at other plants, the chief differences being:a. For maintenance of production of 98% H2S04 , an unusually high S02 concentration is required, because of the prevailing high temperature 'of the purification train cooling water.b. The entire sintering operation is conducted on two large machines, 55ft. x 10ft., operating in series as "First" and "Second over" machines (a two-pass roast.) Any interruption" to either machine causes a complete interruption of plant operation and gas flow.

Jan 1, 1951