Search Documents

By Y. T. John Kwong

Abstract - To exploit an ore deposit without unduly impacting the environment is a challenge that can only be met by the concerted efforts of traditionally independent teams working on a mining project. Not only is detailed geology required of geologists to help mine engineers to develop a mine plan that assures generation of the least possible amount of mine waste, but metallurgists also have to select the most environmentally friendly mineral processing schemes, and communicate with environmental engineers with regard to complications that process chemicals may pose on proper mine waste management. Traditional ore deposit models typically emphasize the geological and mineralogical aspects of ore genesis to facilitate exploration for similar deposits. Recent research has shown that potential environmental liabilities such as acid mine drainage and metal leaching can readily be predicted according to deposit types. The choice of mining methods, mineral processing schemes, and decommissioning options are also largely dictated by the composition and setting of an orebody to be mined. Integrating such related information into traditional ore deposit descriptions would lead to the development of comprehensive environmental ore deposit models. The latter would facilitate communication among staff of the varied components of a mine project and aid with the selection of a combination of methods and strategies that would assure minimum environmental risks and impacts, reduce the overall project cost, and enhance sustainable development.

Jan 1, 2003

By Arash Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5 M tons. The underground mine has three active development panels and one longwall panel. The mining horizon is about 500 m below surface and strata liberate methane. Three surface-based blowing fans provide ventilation air. A ventilation survey and subsequent analysis was undertaken and a simulation model developed. Air heating during winter is essential to prevent freezing of pipelines and to lesser degree, for miner comfort. Air at all three intake shafts is heated using gas-fired heat exchangers. A strata heat study was conducted in one of the active panels to determine rock attributes. Tests included in-situ measurements of rock thermal conductivity and geothermal gradient. Continuously methane monitors have also been installed in an active development panel?s return drift. Ventsim ventilation software was used to aid the heat and contaminant simulation study. An exercise was also undertaken to gain some understanding of methane contaminant levels throughout the mine. It was further used to determine an adequate surface intake air heating rate and consequently the minimum natural gas consumption needed for winter intake air heating at the mine.

Aug 1, 2013

By Marc Piard

In a cool mine, tapping high-pressure lines through reducing valves lowers the temperature beyond remedy. It is the writer's suggestion that, for low-pressure work, law-pressure air ,should be generated in a compressor installed underground adjacent to the work, and that the jacket-water of the compressor should be utilised for re-heating purposes. Such a system of compressed air distribution, designed especially for service in cool mines, is described in the following notes. The suggested system includes a three-wire pole line from the sub-station to the opening nearest to the working face, with a cable connection extending to the latter from the openings; an electrical centrifugal unit; a reservoir excavated in the ground; and a distribution line, re-heated by jacket-water. As regards the reservoir, it may be pointed out that in many mines there are blind or abandoned tunnels that could be used for the purpose. The centrifugal type of compressed air machine is a comparatively new departure, and it was formerly considered that such a machine, operating at less than 1,000 kilowatts per unit, would be commercially impracticable. At the present time, however, these machines are being built in Europe for as little as 400 kilowatts per unit, and as much as 110 lb. per sq. inch pressure. One advantage which these centrifugal machines have over other types is that they may be driven by plain induction motors, without the help of special starters-a consideration of the first importance where the electrical regulations are severe.

Jan 1, 1926

By Lanny Pasternak

"This article is directed at plant production, engineering and maintenance personnel. Seldom does any industrial operation take the time to study the costs involved in the generation of what is probably their most expensive plant utility energy source.IntroductionIn the typical industrial plant in Canada, a 200 hp, 900 cfm, air compressor costs about $60,000* per year to operate (Fig. 1). In 1989 when BC Hydro embarked on their industrial energy management program Airflow Energy Ltd. were asked to spearhead the “Efficiency Compressed Air” portion of that program with a mandate to perform onsite overview surveys and physical hands-on testing of some 300 selected industrial plants throughout British Columbia for compressor efficiencies and wasteful air leaks (Fig. 2). The program duration lasted until 1995, during which time a tremendous amount of data were amassed relating to equipment types, clients’ operating habits, end-use applications and operating costs.During the past six years, Airflow Energy also performed somewhat similar surveys but on a smaller scale in Alberta, Ontario, the United States and the Republic of China. It was no surprise to find some inherent equipment concerns related to efficiency as well as neglected energy wasteful air leaks, so British Columbia was not alone and the problems appear somewhat universal."

Jan 1, 1996

By X. W. Yi, Z. J. Li, G. W. Ma

In this paper, the compressive strength and failure patterns of reinforced cemented paste backfill (CPB) were studied aiming to promote the stability of backfilled stopes. The concept of ductile backfill was proposed and a series of unconfined compression tests were carried out on both non-reinforced and reinforced cemented paste specimens. Portland cement (3% to 5% by weight of tailings) and five different types of ductile materials (0 to 0.5% by weight of solids) were employed in this experiment for the specimen preparation. The test results showed that inclusion of ductile materials enhanced the unconfined compressive strength (UCS), reduced the post peak stress loss and transformed the failure behaviour of specimens from classical brittleness to ductility. The strength of CPB reinforced with different proportions of polypropylene fibres was compared. The stress-strain curves illustrated that both cement and fibres contributed to the increase of UCS, but higher strain values at the peak stress were achieved by fibre reinforcement. CT sliced images acquired from X-ray computed tomography (CT-scan) demonstrated that the reinforced specimen developed irregular crevices at the edge of cross sections and gained the capacity of bearing large displacements owing to the mobilised tensile strength of fibres. It leads to the potential of avoiding unexpected falling blocks of CPB when adjacent mining occurs. This finding highlights a strategy to improve the self-supporting capacity of the fill mass with less cement usage and reduce the ore dilution rates when excavating to adjacent stopes.

Jan 1, 2015

By Y. Sugiyama, K. Kitazono, T. Miura, K. Matsuo

"Impact energy absorbing system for automotive is an important technology. Open-cell porous aluminum alloys were manufactured through Powder Bed Fusion (PBF) process. Compressive properties of the porous aluminum alloy depend on the cell structure as well as the porosity. The authors manufactured two ordered cell structures, truncated octahedron and rhombic dodecahedron, and one disordered cell structure, random Voronoi structure using a 3D-CAD software. Compression tests revealed the anisotropic deformation of the porous aluminum alloy with ordered cell structure. On the other hand, the porous aluminum alloy with disordered cell structure showed relatively isotropic and uniform deformation, which is suitable for energy absorbing applications. Therefore, controlling the disordered cell structure designed by Voronoi diagram enables to develop the advanced porous aluminum alloy having various mechanical properties.INTRODUCTIONAdditive manufacturing (AM) process enables to manufacture near net-shape mechanical parts. The AM technology is typically focused on titanium alloys due to their high specific strength and biocompatibility (Attar, 2014). Recently, aluminum alloy parts can be manufactured through selective laser melting method (Leary, 2016). Metal foams or porous metals are lightweight cellular materials having closed-or open-cell structures (Banhart, 2001). Aluminum foams are focused on as an energy absorbing material for transport industries (Baumeister, 1997). The purpose of the present study is to investigate the optimal cell structure of open-cell porous aluminum alloy manufactured through AM process. Most previous researches on the AM aluminum lattice structure has been considered ordered and periodic cell structures. On the other hand, classical aluminum foams manufactured through cast or powder metallurgical processes have disordered and heterogeneous cell structures (Körner, 2000). The authors use a concept of Voronoi diagram (Moukarzel, 1993) in order to manufacture various cell structures."

Jan 1, 2018

By C. Kuehmann, B. Tufts

QuesTek Innovations has applied its Materials by Design® methodology to computationally design a new ultra high-strength corrosion resistant steel. Ferriurn® S53 eliminates the need for toxic cadmium coatings currently used on conventional steels in landing gear systems. S53 has the strength of 300M steel, and corrosion resistance similar to 15-5PH stainless steel. S53's corrosion resistance improves stress corrosion cracking resistance and reduces susceptibility to hydrogen embrittlement, improving component reliability and providing an opportunity for extended overhaul and repair intervals. Ultimate tensile stress is 1965 to 2000MPa. S53 was designed to be mechanically equivalent to 300M, with the key addition of intrinsic corrosion resistance. Alloy design, microstructural characterization, and mechanical properties are discussed herein.

Jan 1, 2006

By O. Zach, K. Gamweger

"The Process of gas purging in molten Aluminium has been an industrial practise for many years. The melting of alloying elements and their rapid distribution in the bath is very important. To improve the mixing and homogenisation process, at RHI NON FERROUS METALS ENGENEERING GMBH a lot of CFD calculations were done. The so developed new ""purging program"" was tested at Alumino Catalan S.A., Spain. The results of the testtrials were very satisfactory and corresponds very well with the calculated data."

Jan 1, 2004

By A. M. Reyes

Flow field hydrodynamics of serpentine flow channels was investigated numerically using computational fluid dynamics (CFD). The velocity profile simulated by the CFD model was evaluated with respect to experimental results from the literature. Rectangular and tapered flow channels were compared with respect to mixing and water management capabilities, and pressure drop. The CFD model was further developed to account for electrochemical reaction on the cathode side to determine which channel configuration was most effective in reactant conversion. The velocity profile differences between the channels were found to impact reactant conversion, as the rectangular channel had the highest conversion. With respect to water management, although the tapered channel was found to have a higher overall pressure drop, the rectangular channel was found to have higher shear and pressure forces acting on simulated liquid water droplets in the channel.

Jan 1, 2005

By A. P. Sasmito

It is well known that underground miners are exposed to one of the most dangerous working environments on earth. As mine delve deeper, the geological factor, mine position and climate condition as well as heat generation from mining machine give rise to the mine operating temperature. This, in turn, has an adverse effect on the environment and thus leads to higher operating costs. Careful estimation and design of air flow rate, spray system, cooling load and additional ventilation auxiliary equipment are of importance to ensure safety, comfort and productivity whilst maintaining low operating cost. A computational fluid dynamics simulation approach is employed to examine underground mine ventilation in a 36 m cul-de-sac of tunnel of coal mine. The model predictions in the turbulent range were validated by comparison with published data. Different turbulence models were tested to select one that yields adequate accuracy and is computationally efficient. Effects of the following parameters are evaluated: tunnel geometry, air flow rate and inlet air temperature. The objective of the simulation is to arrive at an optimal strategy for ventilation and thermal comfort at low cost.

Aug 1, 2013

By J. Abrahams, A. Nesbitt

Over the past half-century, researchers have commented on the complexities of ion-exchange processes, but have been forced to use gross assumptions to simplify the associated mathematics sufficiently for mathematical models to be of practical use, given the available computational power. This paper reviews the development of increasingly complex models as computational power has increased over the past half-century, from the direct application of Fick's Law in 1947, through to today's models requiring finiteelement methods. The assumptions required for and the associated limitations of the various models are presented and the associated computational complexities are discussed. A case study is presented in which a continuous loss of capacity in an acid resin was observed over about sixty cycles of loading and elution. Resin poisoning does not explain this observation. This paper presents the capacity loss data, speculates on possible causes of the phenomenon, discusses why conventional kinetic and equilibrium mechanisms cannot explain it and concludes that the need to develop a more rigorous model is apparent. The significance of this observation is that standard tests done for a new resin application could significantly overestimate the commercial performance of the resin concerned, highlighting the importance of computer simulation in this field of process engineering.

Jan 1, 2005

By H. W. Smith, N. Ichiyen

A convenient method for the calculation of metallurgical balances, based on statistical treatment of all available data, is presented. An error analysis is included. Examples show the advantages of the method, and also that such balances are less precise than might be supposed.

Jan 1, 1973

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013

By B. M. Das, V. J. Hucka, J. H. Tu

Subsidence can cause serious damage to surface installations such as railroads, highways, pipelines, buildings and other facilities over a period of many years. Although total elimination of the effects of subsidence is difficult, the damage can be minimized through a systematic analysis. An example of such a study for reducing the effects of subsidence on pipelines is presented in this paper. Subsidence-induced stresses on a pipeline over some coal mining properties in Utah have been analyzed using a computer with graphics capabilities. The results are useful in predicting the extent of damages due to mining subsidence. In view of the gradual replacement of room-and-pillar mining by longwall with caving, this sort of analysis will become more and more important. In the next phase of this study the predicted results will be compared with the permissible stress levels on pipelines over actual subsided areas in an actual case.

Jan 1, 1989

By Willie Manfrey, Richard Klimpel

This paper describes the effects of slurry viscosity on the selection-for-breakage and breakage distribution parameters in the wet grinding of cres. A series of experimental tests were run on laboratory scale ball mills. Slurry viscosities were modified by varying the solids/water ratio with and without the presence of selected chemicals. Very consistent and predictable correlations are shown to exist. The grinding parameters were calculated using a computerized back -calculation technique developed by Klimpel and Austin. Industrial scale circuit calculations and preliminary plant trial data suggest that considerable increases in throughput and/or fineness of grind can he achieved through the judicious use of chemical additives.

Jan 1, 1977

By O. Garg

This paper summarizes the computer applications in open-pit mine planning at the Iron Ore Company of Canada (IOC). A brief history of the use of computers at IOC is given, and a description of the existing facilities is outlined. The following systems are discussed: storage and retrieval of geological data; geotechnical data analysis; long-term grade and tonnage forecasting; ore grading; and open-pit mine design. Justification for using computers in open-pit mine planning is given, and possible future areas of application are considered.

Jan 1, 1979

By R. R. Tatiya

"The ultimate aim of a mine design is to determine the development work involved and resources required by adopting one or more specific alternatives. A part of the process is the production of mining plans/designs, an outline of the amount of work and costs involved as well as a prediction of the revenues expected. The paper aims to examine these aspects of mine design using the computer models developed. These models are capable of designing and performing economic analysis for one or more stopes for a continuous orebody. IntroductionTatiya and Allen (1987) have described ’defining stope boundaries using a computer.’ Using the stope boundaries defined or even hypothetical ones, algorithms have been prepared to design the layouts of the following stoping methods: 1. sublevel stoping (longitudinal as well as transverse);2. DTH (Down-the-hole) stoping; and3. flat back cut and fill stoping with posts and pillars.Tatiya (1989) presented this work at the 21st symposium on the application of computers and operations research in the mineral industry (APCOM). Economic analysis of a stope is the additional feature incorporated with these algorithms.The system has been tested by an economic analysis of the three stoping methods modeled for a small portion of a deposit of a copper mining complex. The deposits at this mining complex form lenses of varying shapes and sizes, having low copper content. These chalcopyrite lenses are steeply inclined with a thickness in the range of 5 m to 60 m. The strata are competent and suitable for underground mining.In different sections of the mines different sets of equipment are used to perform the basic unit operations. Some of the ore handling levels in the mines are trackless, the rest are tracked."

Jan 1, 1998

By H. W. Smith, C. L. Lewis

"A process control computer has been installed in the Lake Dufault concentrator to: (a) control the on-stream X-ray analyzer and convert chart readings to elemental percentages, (b) calculate the flow rates required for the most important flotation reagents, using the amount of material entering the process, the analyses and the slurry pH, and (c) set the reagent feeder to these flow rates automatically. Although this project was largely experimental, to gain knowledge and experience in flotation process control, the objectives have been met and fully automatic computer control is now the normal mode of mill operation.This paper describes project planning and defines the system with respect to both control design and functional design. System operation -as seen by the mill operator -is detailed. Implementation of the system is described and the system is discussed in terms of its success, economic justification and future plans."

Jan 1, 1969

By M. Amsden

"Since the computer program is far from complete this must be only a brief progress report on the computerization of flotation metallurgy at the Ecstall concentrator at Timmins.Ecstall is currently treating about 10,000 tons per day of two different ore types. One is a low sulphide copper-zinc ore, the other is a high sulphide lead-zinc-silver ore. The concentrator is divided into three individual grinding and flotation circuits. In effect there are three mills under one roof. Normally there are two circuits on copper-zinc ore and oneone lead-zinc-silver ore. At this point in time one of the copper-zinc circuits is under computerized metallurgy control.The first step in this control is the use of an ARL on-stream x-ray analyzer, coupled with a Honeywell 21 computer which types out assays and recoveries for each individual circuit. Our approach to a computer program was to keep it simple. The program was written to coincide as closely as possible to what an operator would do in the performance of his duties based on the in-formation he was getting from the x-ray analyser read-out. Initially, computer control was put on just the copper circuit of the ""A"" Division, controlling the collector addition at three points in the circuit; primary, secondary, and scavengers. The control was based on recoveries and the grade of the copper concentrate. Targets like 95% recovery and 24% copper concentrate grades that it was felt the circuit could achieve were set to start with. It quickly became apparent that this alone was not enough because if on a certain ore the best recovery that could be made was only 94.9% the computer kept calling for more reagents until the circuit was completely out of control. On another ore it might have been quite possible to get 96% recovery but when the set point of 95% was reached the computer stopped trying for any more. To overcome this problem a very simple optimum seeking program was devised by one of the Ecstall staff and it has worked very satisfactorily since being put into use in July 1970.In the copper float only the two collectors R-208 and the xanthate R-317 are under computer control. The addition of frother and depressant is left to the operator. The flotation cells have automatic level controls which can be adjusted by the operator. pH is controlled automatically through a lime loop-sensor arrangement."

Jan 1, 1971

By A. Trusiak

"Increasing energy costs in mineral processing is making it necessary for tighter controls over various parts of the concentrating process. Continuous monitoring and control of critical process streams can be easily performed by today's many computer systems. Indeed, the list of successful applications of computers to grinding and flotation control continues to grow. The day is rapidly approaching when the use of computers within concentrators for either process control or simply metallurgical accounting will no longer be a luxury, but a necessity. The benefits from such applications far out weight the initial investment.This paper describes the current application of a process control system at Brunswick Mining in north-eastern New Brunswick. Emphasis is placed on the control of a CuPb flotation circuit, and the benefits derived-from this control.No. 12 Cu-Pb Flotation: The complex nature of the Brunswick flotation process has been described else-where. 1,2,3 Four final concentrates are eventually produced, these being a Zn concentrate assaying 53% Zn, a 30% Pb concentrate, a 20% Cu concentrate, and a bulk Pb Zn concentrate assaying 35% Zn and 17% Pb. The Cu concentate, Pb concentrate, and bulk Pb Zn concentrate are all derived from a primary CuPb concentrate assaying 26% Pb, 11% Zn and 1.8% Cu.The No. 12 CuPb circuit produces approximately two thirds of the total primary CuPb concentrate. No. 12 ore, assaying 3.5% Pb, 9% Zn, 0.25% Cu and 100 g/tne silver, is ground in two parallel grinding circuits. Each line uses a 3.2 x 4.2 meter rod mill in closed circuit with two parallel 3.2 x 3.9 meter ball mills. Ball mill and rod mill discharges are classified in two stages of cycloning. The secondary cyclone overflow, or flotation feed, is controlled at 65% passing 37 microns."

Jan 1, 1981