Search Documents

By R. J. Enright

Eight mines in canada and three in Australia were visited between September 1987 and Februacy 1988. All mines had encountered problems with sulphide dust explosions and had introduced defence mechanisms to prevent or limit the extent of these explosions. Techniques included dispersion of limestone by various methods, use of water foggers, placing of water and inert stenuning in blast holes, and removal of settled dust to prevent secondary explosions. The techniques were evaluated and it was concluded that certain practices should be modified or discontinued as they were of little value in preventing dust explosions.

May 11, 1988

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015

By Bruce Peberdy

Outline ?Building Systems ?Climatic Effects ?Thermal Effects ?Building Components ?Building Materials ?Structural Deterioration ?Maintenance Considerations

Nov 1, 2011

By M. Abouhamad

According to the Canadian Urban Transit Association (CUTA), 140 Billion CAD is required to maintain, rehabilitate, and replace subway infrastructure between 2010 and 2014. The current practice adopted by transit authorities for prioritizing subway stations for rehabilitation is based on the station structural needs. While this classification is reflective of station condition, other factors, such as station size, location and passenger capacity, play an important role. The criticality of a station is an index that represents the functional importance of a station depending upon a set of identified factors. The system criticality is based on several attributes, such as station location, size, and nature of use. This paper presents a novel method of clustering subway stations for rehabilitation priority based on their criticality level. The different stations in a subway network are rated according to their relative importance against predefined attributes. The weights and scores of the attributes are computed with the help of experts and current subway network data. The analysis is done using the Fuzzy Analytic Network Process (FANP) to accommodate the subjectivity of human judgment as being expressed in natural language which entails ?fuzziness? in real-life problems and account for the interdependency between the selected attributes. The output of the model is a criticality based clustering of subway stations. The proposed framework helps authorities prioritize stations for rehabilitation and highlight stations with more criticality for a more robust asset analysis.

Aug 1, 2013

By Ian S. Thompson

"Exploration properties form a continuum from grass roots to those with favourable geology, geochemical and/or geophysical anomalies, mineralization, showings (prospects), and finally to those with defined mineral deposits. Often properties exhibit a composite of these categories.The most problematic to value are properties or deposits that are not economically exploitable at the time of the valuation, due to a lack of exploration, insufficient grade or tonnage, poor mining conditions, or the imposition of socioeconomic, environmental, or legal constraints.Various acceptable methods of valuing the range of all such mineral properties or deposits are reviewed. Some inappropriate methods are also discussed.BIOGRAPHYIan S. Thompson is President and Principal of Derry, Michener, Booth & Wahl Consultants Ltd. (DMBW), an independent consulting practice, specializing in exploration, ore reserve estimations, engineering and valuations of mineral properties.Mr. Thompson is a graduate in Honours Geological Sciences from the University of Toronto with over 35 years Canadian and International experience in mineral exploration and development, including the discovery of base metal. gold and uranium deposits.DMBW is affiliated with DMBW, Inc. in Colorado, and works with independent engineering and financial groups in North America, Europe, Australia and Africa.Mr. Thompson is a national member of CIM; the Associations of Professional Engineers of Ontario and British Columbia; The Geological Association of Canada; The Society of Economic Geologists; The Prospectors and Developers Association of Canada and the BC and Yukon Chamber of Mines.INTRODUCTIONThis paper is presented in response to the request of the Mineral Economics Society of the Canadian Institute of Mining and Metallurgy for a Review of Approaches to Valuation of Mineral Properties, as recommended by the TSE/OSC Mining Standards Task Force.Exploration properties with undeveloped mineral resources range from grassroots acreage without exploration history, to those containing mineralization (or a mineral resource) that is insufficiently explored, to well explored deposits which lack either continuity, or sufficient grade/tonnage, or have poor mineability or metallurgy, such that they are not currently exploitable at the time of the valuation. This does not imply that they do not have value."

Jan 1, 2003

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By Tom Dettweiler

Who We Are A global pioneer in discovery, development and recovery of deep-ocean assets Shipwrecks Deep-sea Minerals Company Overview Founded 1994 HQ ?Tampa, Florida USA Employees 45 Tampa + 150 Abroad Publicly Traded: NASDAQ:OMEX Requires Specific Financial Controls and Reporting

May 1, 2013

By Roger J. Goodman, Don Riva

"IntroductionCrows Nest Resources Limited (CNRL), a wholly-owned subsidiary of Shell Canada Resources Limited, is nearing completion of its first coal project, located in southeastern British Columbia. CNRL shipped over 700,000 tonnes of thermal coal to foreign markets in 1982. With the completion of the metallurgical coal plant in December, 1982, shipments of both thermal and metallurgical coal will increase substantially in 1983 and will approach the anticipated operating capacity of 3.0 million tonnes in 1985. The Line Creek Mine lies some 25 kilometres north of Sparwood in southeast British Columbia (Fig. 1). The open-pit mine is located on top of Line Creek Ridge, with coal being hauled 16 km to the thermal and metallurgical coal preparation plants, situated adjacent to the already existing Canadian Pacific Railway. Most of the coal is moved by 108 car unit trains by CP Rail to coal ports in Vancouver, where it is loaded onto vessels destined for overseas markets. Some smaller scale car load shipments are moved by rail to contiguous markets in the Pacific Northwest. History The southeastern British Columbia area, known as the East Kootenays, is steeped in a rich coal mining heritage, dating back to the latter part of the nineteenth century. Predecessors of Crows Nest Resources Limited were instrumental in developing the rich coal reserves in the area. In 1887, William Fernie, a pioneer-cum-prospector recognized the potential of coal deposits in the East Kootenays. Spurred by the relentless push west of the Canadian Pacific Railway through the Crows Nest Pass area, Fernie recognized that it was just a matter of time before the steam locomotives provided him with his required market. That time arrived in 1897 when Fernie helped to form the Crows Nest Pass Coal Company and coal mining commenced at Coal Creek, near his namesake town of Fernie. During its almost 70-year history, this company produced over 48 million tonnes of steam coal and 8 million tonnes of coking coal. In 1965, the Crows Nest Pass Coal Company was re-named Crows Nest Industries, to better reflect its expanded interests into forest products, and it is the latter company which Shell Canada Resources Limited acquired in 1978. The extensive coal resources of Shell, in both Alberta and British Columbia, were rationalized into one group with the birth of Crows Nest Resources Limited to manage and develop the coal holdings."

Jan 1, 1985

By P. Hansman

"Place Dome Canada's Detour Lake Mine is a low-grade gold producer located in northeastern Ontario. Production is targeted for 2850 tonnes of ore per day. As reserves and mining areas continued to be found below and far to the west of the shaft (Fig. 1), it became necessary to review and upgrade the materials handling facilities. This paper deals with the selection, design and construction of an underground crusher and conveyor system capable of handling up to 450 tonnes per hour from the lowest existing level in the mine.BackgroundThe Detour Lake mine site is accessed via secondary Highway 652 which runs northeast out of Cochrane, Ontario. The road consists of 200 Ian of hard top followed by 100 Ian of well maintained gravel to the mine site. A 1500 m airstrip is maintained at the mine site for emergency use. Prior to 1991, the workforce was flown to and from the mine site. Crews were now bused to the site from Timmins. Remnants of a winter road exist to the southeast which at one time ended in La Sarre, Quebec. This was the route used to haul bulk items during the construction period and early production years.A town site has not been established at the site for the current operations. Instead, a rotational scheme is being utilized whereby most personnel will work seven days on site followed by seven days off site. For some employees, however, the work week is termed as a four/three schedule where they work 42 hours between Monday at 10:00 a.m. and Thursday at 4:00 p.m. with the following three days off. All surface employees and maintenance employees underground work 12-hour shifts. All underground employees work a lOV2-hour shift. Supervisors work a similar schedule as their crews, however, other staff may overlap their rotation during the week.A five-compartment shaft was sunk in 1984 from surface to the 610 m elevation. Shaft stations were established at the 120 m, 260 m, 360 m, 460 m, and 560 m levels. The cage compartment consists of a single deck, 4O-man cage in balance with a counterweight. The cage hoist is an Ingersoll-Rand 10H and is regulated to travel at 4.1 m/s. Two 9 t skips operate in balance at a travel speed of 7.1 mls. The skip hoist is a 3.05 m drum Nordberg. Both hoists are automated to function without a hoistman during normal skipping and cage service runs."

Jan 1, 1995

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By G. P. Holmes

"Bell Copper is situated (Latitude 55°0''N, Longitude 126°14W) on Newman Peninsula on the east side of Babine Lake at an altitude of 2,450 feet above sea level. The mine site is approximately 170 miles north west of Prince George and 40 miles east of Smithers. Access to the property is by way of 30 miles of paved road to the Village of Granisle on the west shore of Babine Lake and then a further 9 miles of unpaved road to Bell Copper's west dock. The two mile lake crossing is made using a tug and barge. A compressed air bubbler system maintains an ice free channel for the barge during the winter months.Temperatures range from summer maximums of around 32 °C to winter minimums in the region of minus 40°C. Long periods in winter may be spent with temperatures in the range of minus 15""C to minus 28°C. Freezing temperatures usually start in October and last for six months. The lake normally freezes over in mid December and the ice breaks up in mid May. Snow accounts for approximately two t11irds of the annual precipitation of twenty-one inches."

Jan 1, 1976

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By Robert B. Parsons

"Considering the traumatic events of Canadian mining taxation of the 1970s, one wonders at the sanity of anybody who tries to predict what the 1980s might hold for the tax structure of the mining industry. Yet, the author agreed to tackle this task when called upon to do so at the annual meeting of the Quebec Metal Mining Association in June. The text of this ""daring"" speech follows.IntroductionI have been asked to play the part of the oracle at Delphi, and to predict what the 1980s might hold for the Canadian mining industry in terms of taxation. To appreciate the challenge of this difficult assignment, try to imagine someone in my position back in 1972 attempting to forecast the balance of the 1970s. I daresay that ten years ago nobody could possibly have conceived of the devastating and casualty-ridden rollercoaster ride that mining taxation actually took in the 70s. Nevertheless, I shall examine the entrails and try to shed some light on what might happen during the balance of this decade as far as mineral taxation is concerned.If one were to retreat deep into history, one would find that taxation generally served one purpose-namely, to raise revenues for the government. More recently, an important second function has emerged: taxation is increasingly being used as a fiscal tool-a tool intended to mould and shape future events in order to accomplish certain economic, social and political objectives. It is these two main forces-the need (or desire) for revenues and the perceived convenience of using taxation as a fiscal tool-which will continue to shape the tax structure of the future.In our assessment of where taxation of the mining industry may be headed, we should be able to learn something by looking at where we have been."

Jan 1, 1982

By J. R. Goode

"The Las Cristinas deposit in Venezuela contains reserves of 12.8 million ounces of gold at a grade of 1.20 g/t (Crystallex, 2004). The deposit comprises fully oxidized saprolite (SAPO) overlying a layer of sulphide-enriched saprolite (SAPS) which lies above carbonateleached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same concentration in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper which has been leached and deposited in the SAPS zone.A previous owner began investigation of the Las Cristinas deposit in 1991. Over the next seven years, the company drilled 1,174 holes with a total length of 159 km, conducted extensive metallurgical testwork, including pilot plant operations, and completed feasibility studies. Construction was started in 1997 and again in 1999, however, on each occasion was suspended.Crystallex has been producing gold inVenezuela since the early 1990s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana (CVG) to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in late 2002 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-inleach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot-scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the testwork conducted in 2003, discusses a 20,000 t/d plant design, and presents economic data."

Jan 1, 2005

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By M. Abumiya, N. Onodera

Stabilization of arsenic via the precipitation of large-sized scorodite (FeAsO4·2H2O) particles usually involves the use of expensive autoclave systems operated under high temperature and pressure conditions. Alternatively, DOWA developed a novel scorodite synthesis process (DMSP®) wherein the Fe(II) ions in solution containing As(V) ions were oxidized by O2 gas under atmospheric pressure. In this process, crystalline scorodite particles were formed via the formation of a gel-like precursor containing Fe(II). Based on this concept, in this study, we have demonstrated the synthesis of scorodite particles by the addition of Fe(III)-containing solution to the experimental solution containing Fe(II) and As(V) ions, without the O2 gas oxidation process. Ferric sulfate (Fe2(SO4)3) was used as the source of Fe(III) ions. Results indicate the precipitation of scorodite particles, comparable to that of the O2 gas oxidation method.

Jan 1, 2014

By Takashi Nakamura, Atsushi Iizuka, Yong Fan, Etsuro Shibata

The level of iron in typical copper slag reaches nearly 40% by mass, in the form of iron silicate. We designed a method to oxidize the nonmagnetic iron silicate to magnetite, permitting the selective recovery of the slag’s iron content by magnetic separation. This would effectively decrease the volume of dumped slag; the reclaimed iron could be used for iron and steel making. The crystallization behaviors of magnetite and hematite were studied as reaction products of the molten oxidation of copper slag. A gas atmosphere of 1% by volume of oxygen was found to effectively precipitate the slag’s iron content as magnetite.

Jan 1, 2015

By L. Becze, B. Pierre, S. Di Carlo, G. P. Demopoulos

From January to June 2007, the autoclave production at the Kidd Metallurgical Site was severely affected as a result of plugged discharge lines and extensive precipitation/crystallization of sulphates that caused massive scaling in different autoclave compartments. Work was performed at McGill University to understand the root causes. The crystallization of zinc and ferrous sulphate salts was investigated in terms of solubility measurements. Scale samples were characterized using chemical and mineralogical-spectroscopic analysis. In this paper, following a description of the Kidd zinc pressure leach operation, highlights from this investigation are presented and solutions used to overcome the problem are outlined.

Jan 1, 2008

By Hevina S. Dashwood

This paper proposes to build on my previous research (Dashwood 2012), which analyzed how and why the norm of sustainable development became institutionalized in the global collaborative corporate social responsibility (CSR) initiatives of major mining companies. Since the late 1990s, the majority of major global mining companies have employed the norm of sustainable development to frame their individual CSR policies and to inform industry collaboration at the global level through the International Council on Mining and Metals (ICMM). This paper proposal seeks to address lingering questions from that research, by developing an explanation for how the normative frame of sustainable development has translated into specific CSR standards adopted by the mining industry. Preliminary findings suggest that, although the global mining industry has reached broad consensus on the meaning of sustainable development in the context of mining, there remains considerable variation between mining companies in terms of which specific global standards they adopt. As members of the ICMM, major mining companies are required to report according to the Global Reporting Initiative (GRI) indicators relevant to mining, and there has been wide-spread up-take of the ISO 14,001 environmental management system standard. However, other global standards, such as the International Finance Corporation (IFC) Performance Standards and the Extractive Industry Transparency Initiative, have not been uniformly adopted by the mining industry. What explains this variation? The paper employs a three-level institutional framework (rational choice institutionalism, historical institutionalism and the ?new? institutionalism in organization theory) to explain the influences on the adoption of CSR standards in the global mining sector. Existing research confirms that institutional context is an important factor in explaining CSR adoption in the mining sector (Dashwood 2012). Are similar forces at work in explaining the variation in adoption of specific CSR standards? A three-level institutional analysis lends itself to uncovering influences both external to mining companies (such as pressures from stakeholders), as well as internal company dynamics (such as managerial discretion). Furthermore, the framework can incorporate dynamics operating at the global level (such as isomorphism), the national level (such as the regulatory regime) and the local level (such as community needs and environmental challenges). The theoretical significance of this framework is that the influences on CSR adoption are more complex than can be explained in a single approach (such as narrow rational choice/cost benefit explanations). On a practical level, insights into how global standards get interpreted and acted upon by individual companies could lead to the development of more appropriate and effective global standards.

Aug 1, 2013