Search Documents

By Craig Naudé

"An enhanced gravity concentrator was installed in conjunction with an Intensive Leach Reactor at the Sadiola plant in Mali last year and commissioned in Dec 2007.There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every 10% of gold recovered by gravity, there was a corresponding 0.1% to 1% additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall 4% gain in plant recovery.With total gold recovery of 12% in the gravity section, grades are increased from 3.54g/t in the gravity feed to an average of 2 600g/t in the concentrator feed to the in-line reactor. The recovery of gold in the in-line reactor is in excess of 98.5%.This paper discusses the background to the project, the laboratory testwork prior to the equipment selection, the operational results of the system, as well as the benefits of the future application of high mass yield centrifugal concentrators in base metals, sulphides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONBesides picking nuggets off the ground or out of riverbeds, gravity concentration is arguably one of the oldest methods of recovering gold. In circa 6000BC people discovered that gold can be found behind the rocks and in depressions of creek beds. By placing rocks in a stretch of channel with the proper slope the first sluice is built, probably around 4,000 BC, and this method is still practiced today."

Jan 1, 2009

By Dharmendr Kumar, Pradip, Beena Rai, Venugopal Tammishetti

"Due to rapid depletion of high grade Indian iron ores, there is a need to utilize low grade fines and slimes. However, these fines and slimes, in their current form, cannot be utilized in steel making due to their high alumina (6-10%) contents. Several beneficiation strategies such as gravity separation, magnetic separation, flotation and selective flocculation are currently being explored for the upgradation of low grade fines and slimes. In our previous work density functional theory simulations were employed to come up with selective flocculants for beneficiation of iron ore slimes. Our simulation results suggested that starch and guar gum are more selective towards iron minerals than other minerals present in the sample. Grinding of iron ore fines becomes necessary in some cases to achieve adequate liberation for removing alumina impurities in Indian iron ores. We have thus investigated effect of grinding of iron ore fines on its selective flocculation-separation.In the present work, we have taken natural iron ore fines from one of the Indian iron ore mines and ground it to -400 mesh (<37 microns) in dry and wet conditions. X-ray diffraction study confirmed the presence of minerals hematite, goethite, gibbsite and kaolinite in the sample. The fine ground samples were used in selective dispersion-flocculation study with corn starch and guar gum flocculants. It is interesting to note that even though the dry and wet ground samples possess almost similar particle size distributions, significant differences were observed in yield and grades of the concentrates thus produced. These differences may be arising due to the coating of alumina containing minerals on iron minerals. We have also studied the effect of addition of dispersant while grinding. Our study suggests that grinding conditions determine the efficiency of the separation process."

Jan 1, 2016

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

By H. Saari, D. Y. Seo, J. Beddoes, T. R. Bieler

Prior work on effects of lamellar orientation on creep rates and other mechanical properties have shown that having lamellae parallel to the tensile axis provides optimal creep resistance and good strength. Consequently, a directional solidification system was used to examine the effect of solidification rate on the development of crystals with lamellae parallel to the growth direction. The nominal chemical composition of TiAl ingots was Ti-46A1-2Mo-2Nb (at%) and the ingots were 20 mm in diameter and 180 mm long. The master alloy bars were placed in a high purity yttria mold on a copper chill plate and raised into the hot zone of a Bridgman furnace. The alloys were melted and then directionally solidified at withdrawal rates of 4, 8, and 12 mm/min. As-cast specimens were sectioned at positions of 4, 22, 66, 111, and 155 mm from the bottom of the ingot to evaluate microstructure and crystallographic texture as a function of distance from the bottom of the ingot. The directionally solidified microstructure consists of continuous columnar grains with fully lamellar structure, a network morphology of primary 13, yttria particles, and interlocked columnar boundaries. For all three ingots, the texture at 4 mm shows many peaks, with isolated strong peaks, and a slight tendency toward <111> plane normals within about 20° of the cylindrical axis. At 155 mm, all specimens showed substantially stronger clustering of <111> orientations near the cylinder axis, with the strongest clustering of poles occurring for the 8 and 12 mm/min specimens. Analysis of diffraction peaks indicates that strongly compressive residual stresses in the radial direction are present in the casting. The combined microscopy and texture analysis provides more complete understanding of the processes of directional solidification of TiAl alloys.

Jan 1, 2004

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By G. Morin, S. Amira, F. Chiesa, B. Duchesne

"The effect of heat treatment on the stress corrosion cracking (SCC) resistance of A206 aluminum alloy was studied using the breaking load test according to ASTM G139 standard. This method uses the residual strength measurement from tensile test specimens previously stressed axially while exposed to the 3.5% NaCl alternate immersion test according to ASTM G44 standard. The residual strength after exposure is used as a measure of SCC degradation. The performed heat treatments were conventional natural aging T4 and artificial over-aging T7 tempers in addition to artificial aging T6 temper added for purpose of comparison. These tests showed that A206-T4 has a good resistance to SCC at pre-loads up to 100 MPa while A206-T7 was prone to SCC for pre-loads of 0 and 50 MPa, and showed total loss of ductility for pre-load of 100 MPa. Both A206-T4 and A206-T7 pre-loaded at 150 MPa showed poor resistance to SCC. A206-T6 showed the worst susceptibility to SCC as it lost all mechanical resistance at the end of the alternate exposure to 3.5% NaCl solution, even without any applied pre-load. Metallographic analyses showed that the resistance of A206 alloy to SCC is mainly affected by the transition from pitting to intergranular corrosion attack. The initiation and the propagation of intergranular corrosion attack might be assisted by high stress concentrations in the pits, particularly for pre-loads higher than 100 MPa. The transition from pitting to intergranular corrosion can also be promoted by hydrogen evolution from growing pits, which supports crack propagation by hydrogen embrittlement.INTRODUCTIONA206 aluminum-copper casting alloy offers ones of the best mechanical properties among the aluminum foundry alloys. This alloy belongs to the 206 alloy family developed in 1970s as an alternative to the highly resistant and ductile but more expensive Ag containing 201 alloy (Tiryakioglu, 2009). A206 showed also good low cycle fatigue strength (Sigworth, 2002). These properties made A206 alloy a strong candidate for some vehicles lightweighting applications. In spite of its interesting properties cited above, A206 alloy was rarely used in critical applications due to its tendency for hot tearing and stress corrosion cracking (SCC). Studies of A206 hot tearing behavior showed that this tendency can be reduced by improving castability and by grain refinement (Sigworth, 2002). The optimisation of the casting design can also prevent the tendency toward hot tearing. The SCC of aluminum-copper alloys arises from their susceptibility to localised corrosion, especially in chloride containing media. The localised corrosion in Al-Cu alloys is caused mainly by their heterogeneous microstructure, where the presence of many phases leads to the formation of micro-galvanic coupling with the matrix. However, most of the studies aimed at investigate the SCC of Al-Cu alloys concerned the wrought ones, especially the AA2024 alloy tempered in the T3 (or derivative) condition and few studies concerned the 206 and cast alloys in general (Alexopoulos, 2009 and 2016; Campestrini, 2000; Vogt, 1998; Talamantes-Silva, 2008; Zhang, 2003). Jean et al. (Jean, 2009) studied the effect of heat treatment on SCC behavior of B206 alloy using alternate immersion technique and grain boundary attack method and did not find direct correlation between the two methods. Another study showed that aging of 206 alloy may make a casting susceptible to SCC (Sigworth, 2002). However, these studies did not provide detailed information about the mechanisms of SCC of 206 alloy, as well as the effect of the stress intensity. The present work investigates the effect heat treatments and the stress intensity on the morphology of the corrosion attack and the SCC behavior A206 aluminum alloy. This study uses the breaking load test according to ASTM G139. This test utilizes direct tensile specimens and was developed to give a more quantitative measure of the SCC performance of resistant aluminum"

Jan 1, 2016

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By H. Jung

The microstructures and grain sizes of nanocrystalline Co and Co-1.1 wt % P alloys were characterized by X-ray diffraction. The corrosion properties of as-deposited and annealed Co-l.l wt % P alloys and pure nanocrystalline Co were studied in a deaerated 0.1M H2SO4 solution using electrochemical measurements and XPS surface analysis. Potentiodynamic polarization testing and impedance measurements revealed that an addition of P to pure nanocrystalline Co improved the anodic-corrosion resistance, however, this enhanced corrosion resistance was compromised by the heat treatment process at 350 and 800°C. The corroded surface of annealed nanocrystalline Co-1.1 wt % P at 350°C exhibited a more porous P-enriched layer compared with the as-deposited case. A sample annealed at 800°C corroded uniformly showing second-phase precipitates. The enhanced corrosion resistance of as-deposited nanocrystalline Co-1.1 wt % P was attributed to the elemental P on the surface that acted to hinder the anodic dissolution kinetics of surface Co following an initial selective dissolution of Co. However, at a higher anodic overpotential region, the superior corrosion resistance of Co-l.l wt% P alloys did not last because of the formation of a non-protective surface film consisting of mainly hypophosphite and phosphate as well as elemental P.

Jan 1, 2005

By Matthew S. Hall

Gold/iron oxide catalysts have been prepared and their catalytic performance evaluated for low temperature CO oxidation. The method and temperature used to dry the sample has a significant effect on their catalytic activity. Analysis by TEM revealed the catalysts contained Au particles, although catalysts with high and low activity did not always differ in their microstructure as evidenced by TEM. Catalysts were characterised using XPS and the difference between the Au(4d) and C(1s) binding energies measured; in general the greater the difference, the higher the catalytic activity of the material.

Oct 1, 2003

By A. Osouli, B. Moradi Bajestani

"Increase in permeability of rock mass is vital for both petroleum and geothermal applications. Hydraulic fracturing is a common method to create and increase the permeability for production. Due to the complexity of fracture propagation in a naturally fractured medium, understanding the interaction between hydraulic fracture (HF) and natural fracture (NF) is of great importance to optimize the fracturing process. The possibility of interaction between HF and NF is partly a function of orientation. Various scenarios are predictable for hydraulic fracture regarding the intersection with NF such as being arrested by NF, crossing NF or crossing the fissure while injecting water into it. Different parameters such as geomechanical and geometrical properties of surrounding rock mass, the operational parameters such as injection rate and the angle between created hydraulic fracture and natural fracture (approach angle) can affect the result of hydraulic fracture and natural fracture intersection. In this paper, using a series of flow-coupled Distinct Fracture Network (DFN) simulations, hydraulic fractures were analyzed to investigate the influence of the aforementioned parameters on the hydraulic fracture propagating. Results show that the most significant parameters affecting the interaction of natural and hydraulic fracture are orientation of the intersection as well as injection rate. The interaction and fracture propagation in NF and HF intersections are also studied and discussed in detail.INTRODUCTIONThe hydraulic fracture technology has substantially changed the oil, gas and geothermal industries. With the help of this technology, extraction of fossil resources from tight shale reservoirs will be economical, feasible and sustainable. Due to presence of massive oil and gas trapped in these reservoirs, this technology has been the center of attention for the past 40 years (King, 2012). Hydraulic fracturing is the process in which high pressure water is pumped into shale unconventional reservoirs with low to ultralow permeabilities. With this process paths are created in these mediums for delivering oil and gas to horizontal wellbore and increase the surrounding rock medium permeability. Economical and sustainable stimulation of these tight reservoirs is highly dependable on our understanding in regard to fracture propagation in the highly complex rock medium. Hydraulic fracturing process in rock mediums with preexisting natural fractures is more complex because of the high possibility of Hydraulic Fracture (HF) being arrested or deviated by Natural Fracture (NF). Also, HF and NF intersection can influence the required pumping pressure, injection rate, the outcome of horizontal wellbore and the affected geological underground zones. Since the 1950s, numerous studies have been conducted to predict and plan fracture propagation with the help of modeling and simulation methods. Having a thorough and accurate prediction of fracturing process will not only prevent stimulation of unwanted geological zones or pollution of aquifers, but also will improve the efficiency of the fracturing process. Previously, several studies have been conducted in order to investigate and analyze the interaction of hydraulic fracture and natural fracture (Cottrell, Hosseinpour, & Dershowitz, 2013; Doe, Lacazette, Dershowitz, & Knitter, 2013; Shakib, 2013; Zhang & Jeffrey, 2006)."

Jan 1, 2015

By Yasuo Iizuka

We have had studied CO oxidation on unsupported Au powder (mean particle size, ca.100nm) manufactured by evaporating ultra high purity gold metal (>99.99%) in inert gas and reported that it showed some activity after oxidizing pretreatment in O2 at 423 K?453 K. However, recent XPS analysis of the Au powder revealed that it contains much amount of impurity metals such as Ag and In at levels which far exceed those expected from the impurity level of raw gold metal in the bulk. Several samples of Au powder containing different amount of impurity metals were prepared to examine whether the activity depends upon the existence of surface impurity or not. Activity measurements were performed at 273 K after undergoing the powder under various pretreatment conditions. Although the activity of Au powder varied to some extent according to the pretreatment condition, it is strongly correlated to the surface concentration of Ag. Such dependence was not found for In, indicating that the activity of unsupported Au powder is mainly due to the existence of Ag in the surface layer. The activity attributable to ?particle size effect? was not recognized for Au powder with a mean particle size larger than 80 nm.

Oct 1, 2003

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

The Discrete Element Method (DEM) is a powerful tool for analysing the flow of charge, the energy consumption and the pattern of energy utilisation of a SAG mill. With the development of laser scanning measurement, the detailed internal working surfaces of a SAG mill can now be included in DEM models. Using scanned results for new and worn shell liners for a 32? (9.75 m) SAG mill, it is shown that the feed and discharge lifters have significant effect on the flow of the charge introducing significant threedimensionality. The effects of the resolution accuracy of liner geometry and the lower cut-off of the rock size distribution are explored. Finally, using a matched new and end of life worn liner and operating conditions taken from site surveys, the effect of wear on charge motion, distribution and energy utilisation are evaluated.

Jan 1, 2012

By Arthur. H. Winckers, Stephan L. Chryssoulis

"The deportment of gold in residue samples of cyanide leach tests of David Bell ore from level 6A block 13 was established using a comprehensive quantitative mineralogical approach. In every test the feed was first pre-aerated for 4 hours, followed by 48h cyanidation. Test no. 2 was done without lead nitrate and yielded a residue assaying 3.03g Au/t. In test nos. 4 and 9 lead nitrate was added before pre-aeration at 0.03kg/t and 0.3kg/t respectively yielding residues of 1.04 and 0.81 g Au/t.The mineralogical approach employed to establish the deportment of gold involved superpanning, to preconcentrate the free gold and assaying of the tailing fraction to determine the gold associated with quartz. It was thus determined that without lead nitrate added 47.2% of the lost gold is in the form of residual free gold particles less than 20 µm in size. It is this form of gold which is under represented in the residues of leach tests with lead nitrate added.Having eliminated coarseness of gold particles as a factor for lower recovery, it was determined that the residual gold particles have extensively contaminated surfaces. Amongst the deleterious surface contaminants identified: S, As, Ag, Sb and Hg, the two most harmful are S and Hg because of their concentration on the surface and rate of accumulation.Mercury and Ag are minor constituents of native gold at David Bell (average composition Au: 78.9 wt%, Hg: 18.5 wt% and Ag: 2.6 wt%) and they become enriched on the surface of residual gold particles because of their slower rate of dissolution in cyanide. The other elements absorb onto the gold particles from solution.The beneficial effect of lead nitrate was documented by comparative surface analysis of gold from residue samples of 48 hour leach testing with and without lead nitrate added and from time dependent (0-2 hour) leach tests in the presence and absence of lead nitrate. Lead nitrate accelerates the dissolution of gold by performing the following functions: (i) catalytic effect on the cyanidation of gold by accepting electrons; (ii) reaction with surface sulphur to form PbS which is then removed by oxidation; (iii) catalytic reaction on amalgam and Ag facilitating the cyanidation of Hg and Ag thus slowing down their build up onto the dissolving gold particles and (iv) the precipitation of sulphide sulphur from solution thus minimizing its build up on the surface of dissolving gold particles which is believed to facilitate the access of cyanide ions."

Jan 1, 1996

By A. Ansari

Standard depressants used in the selective separation of copper and molybdenum sulfides by flotation pose environmental and health hazards. In this investigation, the floatability of chalcopyrite and molybdenite in the presence of six well-characterized lignosulfonates was studied through Hallimond tube flotation and adsorption tests. The results define the physicochemical conditions (lignosulfonate type and dosage, pH, presence of ions) for possible selective separation of molybdenite from chalcopyrite. Dissolved polyvalent cations, especially calcium, appear to serve as "activators" for lignosulfonate adsorption on both minerals. From this point of view, the use of lime as a pH modifier is not always appropriate for optimum selectivity since high dosages of lime to produce high pH tend to indiscriminately depress both sulfides.

Jan 1, 2006

By A. Rodriguez-Prado

"Magnetic fields affect the growth of cultured cells and plants; however, limited information exists about their effects on vegetation performing environmental remediation. Constructed wetland mesocosms treating hexavalent chromium (Cr(VI)) wastewater exposed to low-intensity magnetic fields (60 Hz, 56.5 × 10-6 Tesla) produced 100% more biomass than the unexposed control. Nonetheless, they removed only 43 ± 27% of Cr(VI), compared to 60 ± 21% for the control. A Cr(VI) reduction expression was developed as a function of the magnetic field. The design and operation of constructed wetlands to treat mining wastewater can be corrected for magnetic field effects.RÉSUMÉ Les champs magnétiques affectent la croissance des cellules et des plantes cultivées; toutefois, il existe peu d’information quant à leurs effets sur la végétation utilisée à des fins d’assainissement environnementale. Les mésocosmes des marais artificiels traitant des eaux usées, contenant du chrome hexavalent (Cr(VI)), exposés à des champs magnétiques de faible intensité (60 Hz, 56,5 × 10-6 Tesla) ont produit 100 % plus de biomasse que le contrôle non exposé. Néanmoins, ils n’ont enlevé que 43 ± 27 % du Cr(VI), comparativement à 60 ± 21 % pour le contrôle. Une expression de réduction du Cr(VI) a été développée en tant que fonction du champ magnétique. La conception et l’exploitation de marais artificiels pour traiter les eaux usées des mines peuvent être adaptées pour tenir compte des effets des champs magnétiques."

Jan 1, 2015

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006