Search Documents

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By Jacques Deraisme

The technology of percussion drilling is well mastered. The lower cost of percussion drilling allows more holes to be drilled for the same budget. However significant differences are often observed between percussion and diamond drill assay data. This is due to the increased level of contamination associated with the percussion drilling process. Statistical studies on twinned drillholes show that diamond and percussion assays cannot simply be merged in a traditional kriging approach. The question then arises on how to use both types of data to produce reliable resource estimates. To take into account the lower reliability of the percussion assays, a noise characterized by a variance is added to these data. The methodology consists of two steps: 1. Cokriging of the equivalent diamond value at the percussion assay locations. 2. Block kriging using diamond assays and equivalent diamond values, calculated previously, adding to these data a noise, whose variance is the cokriging variance of step 1. This particular way of achieving kriging is called kriging with variance of measurement error. The paper illustrates this innovative methodology with an application on an iron deposit. The results of this method is compared to block kriging using only diamond assays and the gain in precision is quantified. An extension of that approach to multi-element cokriging is also presented.

Oct 1, 2009

By G. H. Blackwell

Open pit mine management must ensure that sufficient trucks are available and are being used effectively for production, and that operating costs are under continued control and review for improvements. This paper describes methods for estimating truck fleet requirements which have been used effectively at large- and medium-sized open pit mining operations. Applied to commonly available data, multiple regression analyses can indicate when mine plans should be revised toward optimizing the number of trucks required. Prediction of major cost items for budgetary purposes is addressed, along with an example of how readily available production data can be used to reduce costs systematically.

Jan 1, 1999

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By M. Pierce

Empirical relations exist for the estimation of rock block strength at scales larger than standard core sizes. Two recently published relations account for the significant impact that microflaws (pores, open cracks, veins) and weathering/alteration can have on scale effect. These relations were used to estimate the rock block strength of heavily microfractured quartzite from the Bingham Canyon Mine. Predictions were compared to the results of Uniaxial Compressive Strength (UCS) tests conducted on cylindrical core samples of varying microfracture intensity and diameter. The comparison confirms the sensitivity to microfracturing suggested by existing relations and suggests that they would benefit from more detailed consideration of microfracture strength, density and persistence over a range of scales. The results of a numerical study illustrate how Synthetic Rock Mass (SRM) modeling techniques could be used to complement empirical data in the development of such relations.

May 1, 2009

By T. Purushotham, B. Samanta

ABSTRACT; The shaft bottom junction in a mine ventilation system is an important source of shock loss due to the combined effect of bend and area change. The occurrence of high-volume ?ow rates through this con?guration can potentially result in high energy losses. The current research examines the process of shock loss at a characteristic shaft bottom junction of an underground coal mine. Investigations are per-formed on both laboratory-scale models and three-dimensional computational ?uid dynamics (CFD) simulations, under both exhausting and forcing shaft bottom conditions. The effects of the plat roughness and the shaft bottom length on the shock loss factor values are also examined. The studies show that the combined effect of bend and area changes that occur at the shaft bottom junction results in shock loss factors that are much higher than those values resulting from abrupt area change only. The transition from a smooth wall condition to an unlined rough airway condition (relative roughness, e/d = 0.112) can increase the shock loss factors by 40%. The effect of shaft bottom length on the shock loss factor has not been clearly established due to con?icting results produced by scale model studies and the CFD simulations.

Jan 1, 2010

By L. A. Nazarova, M. Vandamme, L. A. Nazarov, R. I. Rodin

"The paper describes a new method of interpreting the “canister test” data for the quantitative estimation of gas-kinetic parameters of coal bed based on the developed model of gas emission from coal sample placed in a sealed container. The model accounts for grain-size composition of the sample, initial gas content S, as well as coefficients of diffusion D and mass transfer ?. The inverse coefficient problem is formulated to find S, D and ??from the data of pressure measurements in the sealed container. It is shown that the inverse problem is uniquely solvable if the pressure is dropped during the experiment. The method has been tested using the data from an underground coal mine in the Kuznetsk Basin.Based on the poroelastic model of a coal bed and Khristianovich’s concept about origination and evolution of the filtration zone F in the neighborhood of a degassing borehole the authors considered the corresponding direct problem on rock mass geomechanical state. It was offered interpretation method for data on pressure measurements in a plugged degassing borehole allows evaluation of the diffusion coefficient, the horizontal component of natural stress field and parameters of F. The related inverse problem of the mixed type is formulated, and the cost function is constructed. The analysis using synthetic input data has shown that the cost function has a number of local minimums arranged on the same straight line, one of the minimums being the inverse problem solution. INTRODUCTIONPre-mine degassing is an integral part of coal mining. It allows mitigation of induced accidents in mines (coal and gas outbursts, rock bursts) (Guide, 1990; Malyshev & Airuni, 1999; Seidle, 2011) and also furnishes an alternative and ecology-friendly energy source—methane (Rice, 1997; Nambo, 2001). Choosing an optimized pattern of degassing boreholes, as well as estimating degassing time and amount of gas recovered requires data on gas-kinetics indices of coal beds out of which the key parameter is a gas content S. According to the latest guidelines for coal mines in Russia (Ruban et al, 2012), mining is allowed if S in a coal bed section is under 7 kg/m3."

Jan 1, 2015

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

By M. Pötsch, A. Kluckner, P. Söllner, W. Schubert

"The in situ block size is a key parameter in the geomechanical characterization of rock masses. It describes the fracturing of the rock mass and thus is a measure for the degradation of the rock mass strength. Several classification systems use the in situ block size. For instance, the Geological Strength Index (GSI) requires the “blockiness” and joint surface condition factor as key input parameters. The “blockiness” has recently been related to the in situ block volume (Cai et al., 2004). Due to the limited information about the internals of a rock mass, it is not possible to determine the in situ block size directly. Currently, the in situ block size is determined by calculations using oversimplified models, vague estimations or, due to the lack of relevant information, it is neglected. As remote measurement systems have become available for rock mass characterization, a more comprehensive record of discontinuities can take place. Measurements can be performed on exposed rock outcrops and in particular on tunnel faces and walls, delivering the location, orientation, spacing and persistence of discontinuities at an arbitrary number and locations. An estimation of the in situ block size at the same level of sophistication is still not available. This paper aims at examining the relationship between visible and measureable information at the rock surface, and the in situ block size. Three-dimensional block model simulations were performed using the block model engine of the distinct element code 3DEC. Initial investigations focussed on the minimally required observation area in order to obtain reliable block size distributions. Based on a representative volume element, a reference distribution of the block area at the observation area for a specific discontinuity system was determined. Subsequently, the size of the observation area was decreased stepwise and each new distribution was compared to the reference distribution. For all analyzed systems, it turned out that the mean block area must be smaller than 1% of the observation area to achieve a reliable block size distribution. Further simulations focussed on discontinuity systems with three non-persistent sets. The results were compared to the formula proposed by Cai et al. (2004). A transformation factor T was introduced which replaces the persistence terms in Cai et al.’s proposed formula. The factor describes the correlation between block volumes generated by persistent and corresponding non-persistent discontinuity sets. The simulations included the variation of the discontinuity set spacing, persistence, and orientation. The mean and additionally the 25%-, 50%- and 75%-quantiles of the block size distribution were analyzed. Examining all values for the transformation factor the distribution can be described by a power function with a negative exponent. The function depends on the persistence only. Finally, the results of random simulations were compared to the analytical formula using the transformation factor. The predicted mean and selected quantiles show a good agreement with the simulation results. It gives a comprehensive picture about the block size distribution in discontinuity systems with three non-persistent sets."

Jan 1, 2015

By F. P. Hassani, J. F. Boily, A. M. O. Mohamed, M. Hossein

The optimal geochemical parameters required to form ellringite in a lime-remediated site have been investigated with the use of thermodynamic modelling. The speciation of sulphate and 10 metals analyzed in samples of a mine tailing from northern Quebec was calculated with a computer model. The model also includes calcium, which would result from the addition of lime to the system. Two speciation calculations were done. The first one is a hypothetical speciation before the onset of precipitation and was used to devise the stability fields of minerals susceptible of forming in high pHs. The stability fields were determined by building activity ratio diagrams with sulphate, aluminum and calcium species concentrations for pHs ranging from 4 to 14. The investigation was carried out for a 25°C solution with an ionic strength less than 0.12. Thermodynamics predict that an optimal stability field for ettringite in the mine tailing samples containing 10-3 mol/L SO4-2,10-2 mol/L of AI(OH)4 requires at least 10-2mol/L of Ca+2 and a pH larger than 11.6. The sulphate contents of the mine tailing samples, however, limit the precipitation of ettringite and monosulphate could be an end-precipitate. The second speciation is in equilibrium with precipitates and provides information on the speciation of the residual metals. If ellringite could be precipitated as a stable form, it could serve as a sorptive agent for residual metals, and, due to its binding properties, consolidate tailings.

Jan 1, 1995

By A. Liard, H. Sommelet, G. Sauriol

"Description des études qui ant conduit à la conception spécifique du système de drainage de la mine à ciel ouvert. Les approches différentes sont examinées ainsi que la valeur du système recommande.IntroductionLa Division Mines Gaspé de Mines Noranda Ltée exploite un gisement de cuivre par mine souterraine et mine à ciel ouvert à Murdochville, Québec. L'exploitation par mine aciel ouvert a commencé en 1965 avec une operation à flanc de montagne. Elle se poursuit actuellement sous Ie niveau de la vallée dans une fosse dont Ie diamètre est de I'ordre de 800 m (2,600 pi), et la profondeur de 150 m (500 pi) sou s Ie fond de la vallee. Elle doit atteindre une profondeur de 360 m (l, 180 pi) sous Ie fond de la vallee , avec des murs hauts de 360 à 490 m et des pentes moyenne de 44°. Le rythrne d'extraction est actuellement de 85,000 tonnes par jour.Dans Ie cadre des etudes entreprises par les Services Techniques de la Division Mines Gaspé, la compagnie Géomines Ltée a été consultée pour étudier les conditions hydrogéologiques et hydrologiques locales et participer a la conception d'un système de drainage superficiel et souterr ain. Un tel systerne de drainage visait: a éviter les importantes venues d'eau qu i affectent I'exploitation en periode de crue; amaintenir les pressions hydrostatiques au sein des parois de la fosse dans les limites imposees par les etudes de stabilite des pentes réalisees par la Mine.Les principales étapes de cette etude ont porté sur: la collecte et la compilation des données sur la géologie, l'hydrologie et l'hydrogeologie du site; . la détermination des caractéristiques hydrauliques du milieu rocheux à partir d'études structurales et de test s de perméabilité;"

Jan 1, 1981

By André Gobell

"La distribution des éléments majeurs dans une séquence de roches volcaniques felsiques, la formation de Waconichi, au sud de Chibougamau, indique que les roches pyroclastiques du secteur ouest de ce segment sont chimiquement anormales si on les compare à la composition moyenne des roches volcaniques de Chibougamau: elles sont caractérisées par une teneur anormalement élevée en f er, en magnésium et en potassium et une teneur anormalement basse en sodium et en calcium; ce chimisme caractérise les encaissants des dépôts de sulfures massifs d 'origine volcanique.Les coulées rhyolitiques massives sous-jacentes au gite de cuivre-zinc avec or et argent de Lemoine ne montrent pas ou très peu d’altération de ce genre. Le schéma de mise en place des dépôts de sulfures massifs d'origine volcanique et la nature des roches en présence permettent de croire que la zone d'altération mise en évidence à l'ouest de la mine Lemoine puisse être reliée à la mise en place de ce gisement d'ou l'im portance de tenir compte des caractères texturaux des roches lors de l'interprétation de données litho géochimiques."

Jan 1, 1980

By J. C. Marchand, M. A. Berube

"L'objectif principal recherché lors du broyage d 'un minerai est de libérer adéquatement ses valeurs utiles en vue de leur concentration ultérieure. La pratique courante consiste à tenter d'obtenir un produit de broyage d'une granulométrie constante. Malheureusement, les propriétés texturales des minéraux utiles varient naturellement dans un gisement et une telle stratégie n'entraine pas toujours pour ces minéraux un degré de libération constant. Pour un rendement optimal du procédé de concentration, cette variable très importante doit donc être périodiquement vérifiée.Jusqu'à maintenant, la plupart des études de libération des minerais se font en examinant des sections polies de particules du minerai broyé. Le GRAAIM a récemment assemblé un système modulaire d'analyse d'images qui servira en grande partie à des mesures automatiques du degré de libération des minéraux. Le système s'avère relativement peu coûteux comparativement à la plupart des analyseurs de texture conventionnels si l'on considère que plusieurs de ses composantes, par exemple le miniordinateur, sont utilisées à une foule d'autres applications, et il permet de plus une grande souplesse d'utilisation puisque l'on a qu'à construire des algorithmes de mesure et de calcul en fonction de l'objectif recherché. Des programmes particuliers permettant des études automatiques de libération sur des sections polies de particules ont ainsi été élaborés. Ils permettent également des mesures de teneurs et de distributions granulométriques apparentes des particules. Des résultats obtenus dans le cas de minerais de fer sont brièvement présentés afin d'illustrer la technique."

Jan 1, 1983

By G. P. Cooper

A comprehensive computational heap leach model was used to evaluate options for operating a chalcocite-ore heap leach process. The stockpile leach model is based on the computational fluid dynamic software framework PHYSICA+ and incorporates various physical and chemical phenomena to simulate fluid transport, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. The leach model is calibrated against small-scale column leach tests, and simulation results are validated against closely controlled column pilot-scale tests. For a given set of ore conditions, the effects of raffinate irrigation rate are examined. Several options for pulse leaching were investigated, and the effects on copper recovery and pregnant leach solution (PLS) grade are described. Model simulations indicated that pulse leaching could be used to control copper grade of the PLS. Finally, an analysis of inventory issues is presented for various lift heights including multi-lift simulations to examine potential operating options. U sing irrigation rate, raffinate copper grade, and lift height as variables in a factorial design of experiments, the simulations showed that raffinate copper grade is the main factor that affects the soluble copper inventory grade.

Jan 1, 2007

By Andrew Thrift

Overview ? Problem ? Research question ? Literature review ? Methodology ? Results ? Discussion and recommendations ? New developments Problem ? Increasingly higher expectations ? Inadequate consultation leads to conflict rather than collaboration ? Consultation practice is often weak on decision-making ? Influence of consultation on planning is Unclear Research question ? Are Structured Decision Processes (based on decision analysis) an effective methodology for involving stakeholders in consultative decisionmaking in the mining industry?

May 1, 2006

By Wei Wei

Mining induced ground movement and/or stress redistribution could cause ground instability issues. This is particularly true when the extraction of large stopes is done with one or two large production blasts. Often enough, it is the nearby mine development like haulage drifts and cross cuts that are influenced the most by production blasts. Proper and timely mitigation of ground control issues due to stress redistribution is required. This is usually done by drift rehabilitation involving the installation of secondary support system in the affected areas of the mine development which include; slashing, wire mesh, and in some cases the use of shotcrete liners. It is imperative that such rehabilitation be implemented to the mine infrastructure in a timely manner in order to avoid aggravated ground control problems and production delays. If the real time performance of the support system is captured, it would be possible to determine the timing for rehabilitation job. Birchtree Mine in Thompson, at the Vale Manitoba Operation, has begun mining the 84 Deep Orebody. One of the identified risks is the stability of the crusher room under mining induced stress redistribution. It is proposed to use the U-Cell technology to monitor the primary support system performance (rebar bolts and extension bolts) and monitor the real time performances of the bolt axial loads. The U-Cell technology is a 7-inch long, coupler load cell that is screwed onto the threaded portion of a rock bolt prior to installation. Rehabilitation in the vicinity of the crusher area where U-Cells are installed is recommended when the bolts have reached 70% of their yielding capacity. Catastrophic ground failure can be avoided by adding secondary support in a timely fashion. This paper presents a case study at Birchtree Mine in Thompson Manitoba, where the performance of primary ground support system is monitored and recorded during production.

Jun 1, 2012

By Bruno Lemelin

Falconbridge Ltd Raglan Mine has been in production since 1998 and has produced annually some 900 000T of ore grading 3.1% nickel, 0.9% copper and 0.06% cobalt. The mine is located in Nunavik, Northern Quebec. The current mine life is estimated at approximately 20 years. Reserves are composed of numerous small ore bodies situated across a 65 km strike length. Planning the extraction of the ten small mineralized zones represents a great challenge to optimize. The overall objective is to maximize the company?s return on net assets. Actual planning uses computerized technology tools like Automod and Mine2-4D, and a conventional discounted cash flow method (DCF) of calculating net present value (NPV). The complex setting of Raglan could benefit from advance valuation techniques such as the real options method (RO). This paper will present the characteristics if the mines that make it a good candidate to use RO to gain further insight.

May 1, 2004

By Michael Moats, Adirek Janwong

The use of cylinder electrowinning cells, such as emew® technology, for the recovery of silver from primary and secondary sources has been growing. In this study, common operating parameters used in silver electrowinning were evaluated for recycling applications. Silver powders were produced from an industrial solution in a laboratory scale emew® cell. A design of experiments was employed to evaluate the effects of HNO3 concentration, iron concentration, current density and solution flow rate on current efficiency, particle size, bulk density, and crystallographic orientation. Current efficiency was affected by each parameter with increasing HNO3 concentration having a strong negative effect, increasing iron concentration and current density having moderate negative effects and increasing flow rate having a positive effect over the ranges examined. Finer particles were produced with increasing current density and decreasing flow rate. Bulk density increased when HNO3 concentration increased. The crystallographic orientation of all powders was dominated by the (111) plane. Increasing flow rate decreased the relative intensity of (200) direction. Based on these observations, silver electrowinning in cylindrical cells can operate at high current efficiency and produce larger powders at low HNO3 concentration, low iron concentration, low current density and high flow rate.

Jan 1, 2014

By A. Takala, B Nielson, J. Schunicht

"Pre-concentration in minerals processing presents clear advantages in energy efficiency, water efficiency, reduction of consumables and minimization of capital and operating costs. Outotec’s sorting solutions are powered by Tomra Sorting in order to achieve pre-concentration of concentrator feed in a variety of mineral processing applications. Sensor based sorting combines advanced sensors with rapid computational evaluation and mechanical separation of valuable material from waste and/or gangue. Modern sensor based sorting machines typically use fine air jets to propel individual rocks, thus optimizing recovery and minimizing “mis-sorting”.Gold is generally present in such low concentrations that sensors suitable for ore sorting cannot directly detect it. Therefore, in order to sort gold ore, properties of associated host rock are used. Free and sulphidic gold is often hosted on the quartz-host rock contact zone. Laser scattering effect can be used to detect the surfaces of quartz and composite quartz-host rock particles for subsequent sorting with very high recovery of 95 to 99%. In addition, ore often preferentially fractures along the quartz-host rock contact zone in the crushing circuit. This behavior helps because it liberates more quartz for detection.The feasibility of sorting is investigated for four gold projects in Northern Europe with similar mineralogy. This includes geometallurgical evaluation, amenability testing, small scale “mini-bulk” factory testing in full scale sensor based sorting. The results of the various tests are presented and basic feasibility demonstrated with information on flow sheet development. In addition, the amenability process is evaluated and recommendations made for future projects."

Jan 1, 2017