Search Documents

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By W. H. Mathews

"The Hardie group of cinnabar claims is in the interior of British Columbia; 25 miles northwest of the city of Kamloops. It is one of a number of mercury; properties scattered along a north trending belt 20 miles long and up to 5; miles wide. In all but one of these properties cinnabar is associated with; dolomite veinlets in zones of carbonate alteration in bedded rocks of Triassic; and Cretaceous (?) age; or in intrusives cutting these bedded rocks. No dolomite alteration or cinnabar mineralization is known in the undoubted Tertiary rocks adjacent to the mercury belt.The mercury showings of the Hardie group lie for the most part in a granitic stock cutting Cretaceous (?) volcanics. The rock in this intrusive shows marked variations in texture and has been described in earlier reports as granite and granodiorice, granite porphyry, and trachyte or dacite porphyry. At Hardie mountain the cinnabar mineralization, unlike that of the other properties, is associated with a fine-grained, almost chalcedoni c, quartz; carbonates, though present, are of minor importance. Some of the most interesting showings are found in an adit in the southeastern part of the property where cinnabar mineralization shows a very distinct structural but not a genetic relationship to a brown porphyry dyke 2 to 8 feet wide cutting a phase of the stock that may best be described as aplitic"

Jan 1, 1954

By Leonardo Flores

"Minera Escondida operates two open pits on a porphyry copper district, southeast of Antofagasta, Chile. During 2005, ore will be delivered exclusively from one pit to two concentrators, while from 2006 both pits will provide ore to these plants. Annual testing programmes on drillhole samples, have allowed for the construction of hardness block models since 2000. These models have delivered two main hardness descriptors, the Bond work index and the SAG power index. These parameters and plant operational specifications have been used as input information to forecast, the expected throughput and ball mill product size (P80) for each block of ore. Two forecasting techniques have been used, an in house model, strongly dependant of bond work index and MinnovEx´s CEET2, dependant of Bond work index and Sag power index and other parameters. Model performance has been evaluated from reconciliating on a monthly basis, the forecasted throughputs against a recalculated plant throughput which accounts for losses in tonnage not caused by ore hardness but instead by unscheduled plant operation problems. The model performance for 2003 was ± 2% yearly and ± 5% quarterly, well within the expected ± 3% and ± 10%. INTRODUCTIONThe Escondida porphyry copper district is located 140 km SE of Antofagasta, Chile at 3150 m.a.s.l, at 24°16’ South latitude and 69°04’ West longitude (figure 1)."

Jan 1, 2005

By K. Thuro, S. Schneider, H. Kasling, P. Ellecosta

"One of the most important methods for material testing is the characterization of the hardness, which is defined as the resistance of a material to the penetration of another one. The methods according to Brinell, Vickers, Rockwell and Knoop are today the most common and standardized tests for metal. As they are developed for predominantly ductile materials like steel, they can’t easily be applied to rocks which react much more brittle under indentation. But just as steel, rock is composed of different minerals and has a specific microstructure. Its mechanical parameters are connected with the particular grains, their cohesion and interlocking, just like steel.The abrasivity of rocks and the accompanied wear of drilling tools today are mainly determined by simple and fast laboratory tests such as the Cerchar abrasivity test or the rubber wheel test. Such laboratory tests are good tribological tests, but there are limits. The Cerchar abrasivity test for example has weaknesses in extreme cases, that mean soft or very hard rock types. This leads to an underestimation of abrasivity, e.g. in poorly lithified sandstones or very hard, fine grained and extremely abrasive rocks. As mentioned, hardness characterizes, depending on the type of deformation, predominantly plastic (metal) or elastic properties (rubber). Rocks are in the range between these two extremes. Since the rock drilling process can be seen as a kind of penetration process on macroscopic and microscopic scales, we picked up the idea to characterize the interaction of rock materials and TBM-disc-cutters with hardness tests. In addition, this supports for a better understanding of the wear process on disc cutters. We used the hardnessdisparity concept after Cardu & Giraudi (2012) because wear can be understood as the interaction between the wear part and the material which causes the wear (tribological system). Several rock-forming minerals and some fine to coarse-grained monomineralic and polymineralic rocks were tested. In contrast to Cardu & Giraudi, we used in the first step of investigations the method after Vickers with loads up to 294.2 N (HV 30), depending on the estimated hardness to get bigger indentations and therefore as well information about the cohesion and interlocking of the minerals/grains. We also tested several associated disc cutters. First results show that with higher loads (HV 5 - 30) and at least 15 indentations, we get a structural hardness in fine-grained rock samples, which allows a good characterization of the elasticity and brittleness. Nevertheless, for the coarse-grained rock samples we need up to 40 indentations for a good characterization. Using this method, a prediction of disc cutter wear is feasible taking into account the hardness of the disc cutter steel. In this paper, we would like to present this approved method in material sciences to derive an additional parameter for the characterization of rock abrasivity and wear."

Jan 1, 2015

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949

By Alyson Morley

The mining sector in Canada is facing significant challenges to develop a competent workforce, including increased technical and logistical operational demands, and the imperative to promote local content. There is an increasingly unpredictable labour pool which can be aging, or have skill shortages, or non-aligned skills. As globalisation continues, companies also require efficiencies during operation across various locations. AMEC has met these challenges in the global oil and gas sector by developing our Capability Development and Competence Assurance (CDCA) program. CDCA is applicable across all process industries, including mining. CDCA supports simultaneous consistency and flexibility by defining competence at task level, with corresponding best practice blended training programs, and evaluation criteria and processes. CDCA then defines role profiles mapped to local task definition. When combined with web-based technology, this granularity allows us to manage high volume workforces, while retaining individual learning plans and progression, aiding job satisfaction, and employee retention.

May 1, 2007

Over five decades ago Kitchener et al. in England and La Mer and Healy in the US were advancing our understanding and application of flocculants, primarily related to water treatment and filtration of sludge. This paper identifies the beneficial uses of flocculants in the mining industry and revisits some less common applications. Flocculants are used in unique ways in the mining industry: (a) to increase the effectiveness of sediment ponds to achieve discharge compliance; (b) to eliminate air emissions and costs associated with concentrate drying; (c) to reduce soil loss by applying a flocculant to erodible soils, and reducing wind and water erosion; (d) to remove/thicken metal precipitates in acid rock drainage treatment; and (e) to enhance clarification and thickening in mineral processing. The mechanism of how flocculants, coagulations and potentially-determining ions function is described and how their use can be controlled and optimized. The potential toxic effects of flocculants and coagulants when used to achieve effluent permit discharge compliance for suspended solids is discussed. A review of numerous best management practice (BMP) guidelines for the design and operation of sediment ponds treating mine site runoff to remove total suspended solids (TSS) and turbidity revealed an absence of a predictive methodology to address regulatory discharge compliance for TSS concentration, turbidity and flocculant-induced toxicity. An essential component of pond design is the need to determine whether flocculants and/or other settling aids are required based on the site-specific soil particle size distributions upslope of the pond. Procedures are provided to predict the need for settling aids and estimate pond discharge quality and downstream impact for TSS, turbidity, toxicity and sub-lethal toxicity. The need to develop BMP guidelines are discussed for (a) the application of flocculant to surface soils to reduce erosion, (b) the application of flocblocks to increase the ?sediment control? aspects of erosion and sediment control, as part of the mine site erosion control plan strategy and (c) the application of flocculant to silt socks to treat mine site runoff.

Aug 1, 2013

By S. Southall, F. McCaffrey, F. Stober, M. Darini

Electrode Columns are commonly used in electric furnaces to deliver current and regulate furnace power to the smelting or melting process. Hatch has developed an innovative patent-pending system for lowering ("slipping") and/or raising ("back-slipping") the electrodes through an electrode column, without requiring the release of any clamping devices. All clamping forces are applied by springs. Unlike systems employing hydraulically applied clamping forces, (e.g., water bladders) the spring system is failsafe. Its inherent simplicity virtually eliminates the need for maintenance. The Hatch system is particularly applicable to Soderberg electrodes, and comprises two axially movable slipping clamps and a stationary power clamp, each of which apply a distributed, radial clamping force to the electrode. The magnitudes of the slipping sleeves' clamping forces and sequencing of their axial movements are selected such that the slipping clamps, in conjunction with the weight of the electrode, provide slipping or back slipping without release of any clamping force.

Jan 1, 2005

By Dwayne D. Tannant

This paper presents a summary of results from a questionnaire sent to surface mines in western Canada seeking information on haul road design, construction, and maintenance. There has been a marked increase in the size of the trucks used over the last decade with some mines now using trucks with a payload capacity of 360mt. Consequentially, geometrical elements of haul roads, such as width, have been enlarged to accommodate larger trucks. Most haul roads are constructed on the basis of past experience without use of formal design procedures. With the introduction of larger haul trucks, problems related to rolling resistance, deterioration, and maintenance of the haul roads have become more important. This has lead to adoption of more rigorous design methods for roads at some mines, most notably for the oil sand mines operated by Syncrude Canada Ltd. A summary of the evolution of haul road designs implemented at Syncrude Canada Ltd. is presented.

May 1, 2001

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

By T. G. Joseph

The chicken and egg scenario where adverse truck motions cause ground deterioration and poor ground profiles that in turn cause adverse truck motions is a downward deterioration spiral that dominates in our industry. If we can remove one action, the reaction must stop and vice-versa. A simple 'truck to excavator' load data analysis and wireless communication system is outlined in this paper; that will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. In turn this will reduce the subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life and ongoing maintenance of haul roads

Nov 1, 2011

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By Frank E. Lathe

During the war the National Research Council at Ottawa sent out questionnaires to the managers of nearly all the industrial plants in Canada. Inquiry was made as to the research equipment possessed, the number of research workers employed and the nature of the research problems which still remained unsolved. Practically all the companies reported that they had no special facilities for research, had no re-search workers and did not require the assistance of the National Research Council-because they had no research problems. Perhaps we have here one of the chief reasons why certain of our manufacturers find themselves unable to meet foreign competition. For hundreds of years the Indian tribes of northern Chile worked, in a small way, the copper deposits at Chuquicamata. They had no research problems and made no striking success of their mining operations. Then came an American company with a research problem, which they proceeded to solve. To-day the stock of that company has a market value of about $140,000,000.

Jan 1, 1926

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

"With the globalization of the mining industry, many companies are now seeking to invest in underground diamond mines, with the purchase of small diamond pipes being seen as particularly attractive. However, recent experiences in South Africa have shown that many projects fail due to a lack of awareness of the hazards associated with diamond mining. In this paper three significant hazards are dealt with — mud rushes, block crushing, and implementation of an inappropriate mining method. Measures that assist in the prevention of these three hazards are given.IntroductionFor over a hundred years, South Africa has been seen as the centre of the diamond mining industry, possibly having the largest number of operational underground diamond mines in the world. Despite the fact that this industry has been dominated by large mines of De Beers Consolidated Mines Limited, many small underground mines have operated profitably for a number of years, exploiting diamondiferous fissures and pipes. In the last decade there has been renewed interest in these small operations from international companies. However, many of these projects have not realized their full potential owing to a lack of appreciation of the hazards inherent in the operation of a diamond mine.Hazards Associated with Diamond MiningIn the development of a diamond mine, the mining company must be aware of the hazards associated with diamond mining. There are three main hazards: (1) mud rushes; (2) block crushing; and (3) selection of an inappropriate mining method (not a natural hazard, but a planning induced hazard). Each of these hazards will be dealt with in turn in the following sections."

Jan 1, 2000

By Chris Harris, Kamal Adham

The use of HCl acid is gaining momentum among hydrometallurgical processes. However, the issue of environmentally efficient and economically viable ways to regenerate HCl acid (from various metal chloride intermediate products) remains a technology and operational challenge. The authors provide a state-of-technology review based on Hatch’s years of testing, design and commissioning experience with high-temperature units (fluid bed and spray roasters), plus the recent efforts in the area of low-temperature HCl regeneration.

Jan 1, 2014

By Simon Weixiao Sun

Conventionally, carbon steel has been the primary material for salt mine headframe construction, protected by specialty paint layers to prevent corrosion. These layers require meticulous QA/QC during fabrication and erection, and the top UV protection layer typically loses effectiveness after an average of 10 years, necessitating ongoing maintenance. As headframes age, significant structural repairs are often required. Alternatively, stainless steel can eliminate corrosion concerns, though its high initial cost has limited its use in headframe design. However, when factoring in long-term maintenance costs, a 'maintenance-free' stainless steel headframe can be an attractive option for stakeholders. This paper compares the structural performance and economic considerations of painted carbon steel and stainless steel headframes, including initial capital and long-term maintenance costs. Additionally, it explores a hybrid approach, strategically using carbon steel in low-contamination areas to reduce initial costs and significantly minimize future maintenance efforts.

May 4, 2025

By Linlin Zhang

Rare earth elements (REEs) are a group of lanthanides elements which have been widely used in the electronic, petrochemistry, metallurgy, and defense industries. Their demand has increased sharply in the past decade with the boom in electronic device production. Some countries now consider them strategic metals for the future and it has been forecasted that REEs may become a dominant contributor to global economy. In the wake of REE exploration, mining and processing, concern has grown over occupational and community health issues and risks. A portion of available literature on this topic however is written in the Chinese language, and thus research information related to health and REE mining is not readily accessible to mineral development planners in countries such as Canada, where REE mining is now evolving. As REEs also represent an important commodity, primarily stemming from Chinese production, it is important to begin to understand the potential health costs related to this mining sector. There are two main objectives of this paper. The first is to present an overview of REE mining with a focus on geological characteristics, global production and uses with particular attention to the main producer: China. The second is to present the results of a literature review (using both Chinese and English sources) on REE mining and health and identifies key occupational and community health issues that require consideration. This paper concludes by identifying some critical issues this sector needs to address to ensure the sustainable development of this mining activity.

Aug 1, 2013