Search Documents

By D. R. Griffiths

"Oxidation of pyrrhotite prcxiuces sulphuric acid which in turn leaches out heavy metals, resulting in acidic contaminated seepages. The establishment of a marsh on top of the pyrrhotite would result in an anaerobic sediment, which should prevent further oxidation of the pyrrhotite. Initial data indicates that concentrations of sulphates and heavy metals in the seepage water are greatly reduced. Further hydrogeological studies are required however, to determine if metal and acidic loadings to the environment have increased.L'oxidation du sulfure de fer produit de l'acide sulfurique qui a son tour attaque les métaux ayant pour resultat une contamination d'acide et de métal des eaux d'infiltration. L'etablissement d'une couverture faite de boue et de vase au-dessus du depot du sulfure de fer réduit les effets de l'oxidation.Les données initiales indiquent que les concentrations de souffre et de métaux dans les eaux d'infiltration sent grandernent réduites.Des études plus poussées sent nécessaires pour déterminer si les quantités de souffre et de métaux dans les eaux d'infiltration ont augmentées.INTRODUCITONPyrrhotite tailings are readily oxidized through a combination of precipitation and atmospheric oxygen causing acidification of the unsaturated zone above the water table. This reaction is usually catalyzed by the bacteria, Thiobacillus ferooxidans. As the pH decreases, heavy metals become more soluble resulting in contaminated seepages to ground and surface waters.By creating a marshland on top of the pyrrhotite, an anaerobic intermediate layer should form between the organic covering and the tailings, preventing the oxidation process from progressing.In September 1986, Falconbridge Limited implemented a tailing reclamation project that involved creating a marshland on top of pyrrhotite tailings. The following paper will discuss and illustrate the preliminary results obtained during the sampling period of May to September 1987."

Jan 1, 1988

By B. G. Cousins, L. Racine, R. S. MacPhail

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate that has shown improved collection properties over SIPX for copper-bearing and copper-activated minerals. Characteristics such as improvement of recoveries with lower dosages and high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31.The most improved results have been seen insphalerite flotation. Plant trial work carried out in the zinc circuit at the Louvicourt Concentratorin northern Quebec has produced data showing superior grade and recoveries from rougher concentrates that previously had not been attain-able with other reagents effectively. The improvement over SIPX adds up to an almost$1,000,000 annual improvement on the mine’s bottom line at present zinc prices.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthates, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by Tennants Research Technology Applications (TRTA), a division of Charles Tennant & Co. (Canada) Ltd., produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The new product has been named FLEX 31. Currently, FLEX 31 is manufactured at the Prospec Chemicals, another division of Charles Tennant & Co. (Canada) Ltd.A large amount of laboratory testing pro-grams have been carried out with FLEX 31 todate (MacPhail and Cousins, 1995; Cousins and MacPhail, 1996). One of the minerals that has a defnite affinity to improved fotation is sphalerite (ZnS). Once activated with copper sulphate, sphalerite has produced some of the most spectacular test work when FLEX 31 is compared directly to SIPX. Plant trials of FLEX31 at Aur Louvicourt Inc. carried out in 1995show that FLEX 31 is far superior to SIPX for activated sphalerite flotation."

Jan 1, 1997

By Robert MacPhail, Louis Racine, Bret G. Cousins

"Sodium Isopropyl Xanthate is employed in a wide variety of sulphide flotation procedures due to the specificity over other xanthates and the cost savings over other sulphide collectors such as thionocarbamates, xanthogen formates and dithiophosphates. An investigation carried out by Tennants Research Technology Applications (TRTA), has produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries.Currently, FLEX 31 is manufactured at the Prospec Chemicals xanthate plant in Fort Saskatchewan, Alberta, Canada. Prospec, founded in 1983, produces approximately 4500 tonnes of xanthates per year and is presently undergoing expansion to produce approximately 6000 tonnes. The proprietary process for FLEX 31 is a new addition to plant operations that include the production of xanthates, thionocarbamates and xanthogen formates.This paper will cover the testwork on the zinc flotation circuit at the Louvicourt Mine in Val d'Or, Quebec. This testwork indicated that FLEX 31 could replace SIPX due to the ability of the FLEX to improve zinc flotation kinetics without adversely affecting final concentrate grade. FLEX has presently replaced SIPX in the zinc circuit at Louvicourt.BackgroundThe Louvicourt deposit is hosted by greenschist facies Archean volcanic rocks located in the southeast portion of the Abitibi Greenstone Belt. In the Val d'Or area, the volcanic rocks form an east-west striking, steeply dipping and south-facing sequence composed of thick mafic and ultramafic flows of the Lower Malartic Group.The joint venture has three partners-Aur Louvicourt Inc. (30%), Novicourt Inc. (45%) and Teck Corp (25%). Aur Resources holds 30% interest through Aur Louvicourt, a wholly owned subsidiary and is the operator of the project. Novicourt Inc. is 60.9% held by Noranda.Approximately 75% to 85% of Louvicourt's revenue comes from the sale of copper; 10% from gold (in the copper concentrate); 7% from zinc and 3% from silver (also in the copper concentrate) The copper at Louvicourt is fairly ""fast floating"". About 60% of the copper in the ore can be concentrated in the first flotation cells with feed grades of approximately 4% copper.The initial testwork and pilot trials had indicated that it would be difficult to achieve zinc grades over 52% and recoveries would have to be kept at a level amenable to salable concentrate grades. The actual mill results, with a fine regrind, achieved zinc grades of 55% to 56% at about 75% recovery."

Jan 1, 1996

By Robert S. MacPhail, Chilombo Henry, Arnold Kabamba, David Mukelebai, Suresh Thirunagari, Bukali Victor, Yoram Kapai, Chomba Leonard, Kanna Amarasingham

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate. Developed by Charles Tennant & Co (Canada) Ltd and has shown improved collection properties over SIPX for sulphide minerals flotation. Improvement of recoveries, grades, faster kinetics, lower dosages, high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31. Recent plant trial carried out in the copper circuit at one of the largest copper mine in Zambia shown over US $ 2.00 Million annual improvement on the bottom line over SIPX at current copper prices. Data produced also showed superior grade and recoveries from rougher concentrates that previously had not been attainable with other reagents effectively. Flex 31 has also shown positive outcomes with zinc, Copper/Zinc, arsenopyrite and copper/molybdenum ores.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthate, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by the research division of Charles Tennant & Company (Canada) Limited has produced a chemically enhanced SIPX. This product has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The product was named “FLEX 31”."

Jan 1, 2016

By Sib N. Mukherjee

Main ventilation fans are used in all the mines and they run continuously 24 hours a day and 365 days in a year. Any improvement in their performance can lead to considerable power saving. The basic principle for selection, operations, and related measures are discussed in brief in the paper. The contributions of different elements of mine fan on its performance are discussed in brief. The means to improve efficiency of a running fan is also discussed and the importance of saving even 1 Kwh is elaborated. It is found that the cost of the energy saved may even permit a replacement fan to be procured in a few years time.

May 1, 2007

By Zhao-shu Sun, Mao-lin Li, Rui Cui

"Fankou Mine produced pyrite concentrate (PC) from the tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34%. The economic value of PC increases with its purity. When the S grade of PC feed to sulfuric acid plant is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the PC with S grade of 47% as target.The direct way to reach that goal was to clean the rough PC Lots of cleaner flotation tests were conducted and the balanced strategy was to produce two ranks PC with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of PC, gravity separation was introduced into the flowsheet. The numerical simulation and tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rough PC. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to PC with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough PC, single PC with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality PC at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry."

Jan 1, 2016

By V. V. Severov, Z. Lafhaj

The flotation separation of salt type calcium minerals is problematic, due to the similarities in their formation properties and the same active Ca2+ related site for interaction with anionic collectors and similar physicochemical characteristics such as solubility, point of zero charge, surface speciation, Ca-site density. The work was performed to achieve effective and selective separation of the calcium-minerals using pure minerals samples: four calcite, two fluorite, and two apatite samples. The effect of pure and mixing anionic collectors such as oleic and linoleic acid to different ratio (2:1; 1:1; 1:2) as well as the role of nonionic collectors on the selective separation of Ca minerals were studied. All flotation tests were performed in self-aspirated flotation cell. The results obtained with the blend of anionic collectors with the molar ratio of 2:1 show a separation between apatite and calcite at pH 5 and a ratio 1:2 at pH 9. The enhancing of separation contrast using the sodium silicate as a depressant for calcite and apatite is also examined as a function of oleate/linoleate ratio. Additionally, this paper discusses the enhancing of the selective separation of Ca minerals when anionic collectors were blended with nonionic reagents. The surface reactions in aqueous mineral suspensions and the adsorption of anionic collectors blended with nonionic reagents were studied by FTIR spectroscopy. An unexpected synergistic effect was observed for some ratios between anionic and nonionic reagents. The mixture of fatty acids and nonionic reagent showed very high flotation efficiency in comparison with fatty acid alone for the flotation of an igneous low-grade phosphate ore.

Jan 1, 2016

By G. Granata, C. Tokoro, T. Kato

"The goal of this study was to evaluate the effectiveness of mechanochemical activation by planetary milling as method to enhance the recovery of cerium from rare earth ores. For this purpose, a weathered ore was first ground by planetary milling and then leached by sulfuric acid. The influence of planetary milling was investigated by assisting the experiments with X-ray absorption fine structure (XAFS) in cerium LIII-edge and inductively coupled plasma spectrometry to measure the concentration of cerium dissolved by leaching. Results showed that, by increasing the grinding time, although the particle size of the specimen increased due to agglomeration, the recovery of cerium significantly increased. This finding clearly indicated that a smaller particle size actually hinders the recovery of cerium. In particular, XAFS analysis revealed that the longer the grinding time, the more tetravalent cerium could be converted into trivalent cerium and such conversion, also called mechanochemical reaction was beneficial to the recovery of cerium. Based on the obtained results, it was confirmed that approximately 70% of cerium could be recovered by mechanochemically activated leaching of rare earth ores.INTRODUCTION Rare earth elements (REEs) are a group of 17 chemically similar metallic elements comprising lanthanides, scandium and yttrium. Since REEs have various unique physical and/or chemical properties, they have become essential materials for advanced application (Adachi, 2015). REEs used in industry are usually supplied as rare earth minerals. In the last decades, flotation, gravity separation, magnetic separation and leaching have been widely applied to recovery of REEs from rare earth minerals like monazite (Archana, Rekha, Manis, Jitendra, & Jin, 2015). Among these operations, leaching has been widely studied in the recent years to improve the state of the art (Archana, Rekha, Manis, Jitendra, & Jin, 2015; Xiao, Feng, Huang, Huang, Chen, Liu, Wang, & Long, 2016; Farzaneh, Fereshteh, & Ahmad, 2017). Aiming to enhance recovery of REEs from rare earth minerals, a possible advancement of leaching technology could be the mechanochemically activation of the ore by high-intensity milling (Alorro, 2016). In the mechanochemical activation, an improvement of the leaching performances can be achieved through high-intensity milling operations which result into a dramatic decrease of the mineral particle size with a consequent improvement of the physical kinetics of leaching. Furthermore, the high mechanical energy provided to the sample during milling can determine the rupture of the crystal structure of the mineral, thereby transforming it into a more leachable form."

Jan 1, 2017

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By Gabka T., R. E. Gregorczyk

Work to improve employees' behavior in Głogów Copper Smelter began in 2009. It has been noted that over 90% of accidents at work are attributable to human reasons. At that time, a series of external workshops was contracted based on exercises conducted by a psychologist trainer with supervisors. Having trained about 300 employees, an observation of employee behavior at workstations was started as part of the control of risk reduction measures. As a result of the above actions, the number of accidents was reduced by half between 2009 and 2017. Currently, internal workshops for communication improvement for behavioral auditors are conducted by the employees of the Smelter. Named: "I observe, react and communicate" and aimed at further mastering the elements of the safety culture in Głogów Copper Smelter. INTRODUCTION KGHM Polska Miedz is an integrated mining and smelting copper producer based in Poland and operates on the international metal market. KGHM, with annual production of over 500 thousand tonnes of copper, holds a middle position in the world ranking of copper producers. At the same time, in Europe it is the largest producer of copper from its own ore deposits, possessing its own integrated production structure, from underground mining operations to final, top-quality product. It is also worth mentioning that KGHM Polska Miedź is one of the largest Polish exporters and, apart from copper, is a significant primary silver producer in the world. The mission of our company, consistent with its strategy, is to produce copper and silver in a safe mode for workers and the environment, with reduced environmental impact. Therefore, "Głogów" Copper Smelter operations are continuously focused on the creation of safe working conditions, and minimizing the negative effects on the environment. The company meets the requirements of an Integrated Management System comprised of the following: Quality Management System ISO 9001:2008 Environment Management System ISO 14001:2004 OHS Management System according to the requirements of BS OHSAS 18001:2007 Being a proud socially responsible company, we are aware that part of an efficient OHS system is to recognize, monitor, prevent, educate and motivate, thus continuously improve working conditions for 2500 employees of Głogów Copper Smelter &Refinery. We clearly communicate that a low accident rate is beneficial for both, staff and the company, and is of utmost importance as a part of our health policy.

Jan 1, 2019

By Y. Miyabayashi, K. Nishikawa, H. Nagai

JX Nippon Mining & Metals Group recovers valuable metals from end-of-life electronic products in an economical and environmentally-benign way, based on technologies that have been acquired in mining, smelting, and refining operations over time. End-of-life electronic products contain halogens and hydrocarbons. When such materials are treated in the copper smelting process, corrosion of equipment and discoloration of sulfuric acid occur. As a countermeasure to these problems, we have developed pretreatment processes that include an incinerator, exhaust gas washing towers, and a defluorination facility. By implementing these improvements, we have been able to treat a large volume of end-of-life electronic products efficiently in the copper smelting process.

Jan 1, 2014

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By Lachezar Tsotsorkov

Being a mining company, Assarel-Medet has a significant impact upon the environmental components. In order to meet the legal requirements and the requirements stipulated by the effective permits as well as to reduce the environmental imprint throughout the years, the policy of the company to implement a number of projects to improve the environmental components quality and the environmental state in the company?s region. The projects associated with atmospheric air quality management and reduction of the impact exercised by Assarel-Medet JSC by implementing various measures to eliminate the potential sources of the impact, preventive and rehabilitation initiatives as well as organizational and administrative activities are among the most important ones. A stable improvement of atmospheric air quality in the region and minimization of the company impact upon the ground air state in the region was observed in the period from 2005 to 2012 due to the applied measures. This project is a contribution to the environmental protection, in particular to atmospheric air protection, by applying integral monitoring and modeling methods to identify the negative impact by the mining companies and plan measures to reduce and restrict it as well as to improve the quality of the environment and living area of people working and living in the impact range as an element of sustainable development.

Aug 1, 2013

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By F. E. Millett

The following notes deal chiefly with changes from steam to electric drives, or, in the case of the Bellevue pumps, from air to electric. Where electric power can be purchased or generated cheaply it can be used to advantage and is generally more economical than steam, especially in places remote from the central power-plant. Nothing could be more simple than the operation of electrical gear. It does not require a competent engineer constantly on the alert, oiling and watching bearings, and maintenance is at a minimum. The ease with which the current is transmitted from its source to where it must do its work is one of its greatest advantages. Transmission losses are very low. Generally speaking, the smaller the plant the lower the loss and 90 per cent, and better, efficiency is easily attained. In and around Bellevue 2300-volt, three-phase, is the standard distributing pressure; our power requirements and the distances transmitted, for the present, do not require more than this. Most of the heavier motors are 2300-volt .machines, which eliminates the cost and possible troubles of step-down transformers, and makes for a cheaper and less bulky motor. This applies to two fan, two hoist, and two compressor motors, the smallest being 75 and the largest 520 horse power. The standard pressure on power lines to all inside pumps is 550 volts, and 220 volts is general for the the tipple. While 110 volts is used for house and office lighting service, it is not economical around and in the mine. No matter what kind of device is used to lock and protect the lamps, they are invariably missing.

Jan 1, 1926

By J. Cueto, M. Torres, J. Fernandez, J. Nuñez, C. Salgado, G. Zarate

Anglo American has used the extractant M 5640 in all the Divisions, which is an aldoxime modified with TXIB formulation, except in Los Bronces, where an aldoxime modified with tridecanol (TDA) formulation is used. It is a well-known fact that the aldoxime degrades while the modifier does not. With time the aldoxime/modifier ratio decreases significantly depending on the operating conditions of each plant. In order to evaluate the effect of this increasing modifier content in the organic of the plant, especially in the organic losses, a complete metallurgical test work program was started at laboratory and pilot plant scale. Results showed that the addition of aldoxime without modifier does not affect the chemical performance of the organic phase, but there is a significant decrease in the viscosity and density of the organic phase. Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at both SX plants, Mantos Blancos and Mantoverde. In these tests, instead of adding the usual formulation of aldoxime modified with TXIB to maintain the organic inventory, CuPRO MEX™ 3406 which is an aldoxime without modifier is going to be added until the original aldoxime/modifier ratio is reached. The plant tests started in April 2013 at Mantos Blancos and in June 2013 at Mantoverde and will last 18 months. The results obtained at the laboratory and pilot plant scale, together with the preliminary plant test results, are discussed in this paper.

Jan 1, 2014

By Roger St. C. Smart, Paul Weber, Joan E. Thomas, William M. Skinner, Warwick Stewart, Stuart Miller

For mine sites affected by acid rock drainage (ARD) or with a potential future ARD issue, the prime consideration is not only the classification of different waste rock as potentially acid forming or non acid forming but also the peak acid (and metal) release rates and expected ARD duration during which effective ARD management and acid neutralisation capacity (ANC) are required. Methods for assessment of this ANC (e.g., Sobek tests) are already available but can be unreliable in ARD containing significant proportions of framboidal pyrite or iron carbonates. The measurement of negative ANC values and the release of S to solution showed that significant sulfide oxidation may occur prior to and during testing in samples containing reactive (particularly framboidal) pyrite resulting in serious underestimation of the original ANC. A simple methodology with dissolution in Ar-purged water before ANC testing, removing ferrous salts, and sulfate assay after ANC testing corrects these effects. Results also showed that a significant lag period (up to 432 h) may be needed for complete hydrolysis of Fe associated with the standard Sobek ANC testing of, for instance, siderite. Hence, the ANC of iron carbonates is usually significantly overestimated. By filtering and the addition of H202 until there was no subsequent pH drop (due to Fe hydrolysis reactions), followed by back titration to pH 7.0, the ANC for siderite was similar to the ANC determined after 432 h lag by the Modified Sobek ANC test and to the mineralogical carbonate ANCcarb determined by calculation based on electron probe micro-analysis. A chemical ANC calculation, based on neutralising cations released to solution, has provided a method to quantify the short-term ANC of carbonates and silicates in simple mixed mineral assemblages and waste rock samples. Results showed that silicate ANC can be more important in short-term neutralisation than carbonate ANC in low carbonate samples. In the longer-term, decreasing sulfate and metal loads with increasing pH values suggests that eventually sulfide acidity generation rates will match the longer-term inherent acid neutralisation rates of the sample derived from silicates. A kinetic ANC measurement for silicates, after steady state dissolution is reached, that indicates the number of hydrogen ions neutralised/m2/yr has been developed. These values can be used in estimates of the net acid production profile from wastes with low (and decreasing) pyrite content after the short-term ANC is exhausted.

Jan 1, 2004