Search Documents

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

By R. L. Brown

The burning sulphide ores in the Sullivan Mine generate sulphur dioxide gases. This paper is concerned with a description of the environmental impact of SO2 on air quality in the mine and on the surface in the vicinity of the mine. As a result of surface caving, SO2 has been able to vent to surface and winds have carried it into one residential area of Kimberley. Monitoring practices are described.

Jan 1, 1977

By R. Brough

"Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind - and Secondary Hills. There are, however, only a few Primary Hills in operation with ""solid"" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a Cost per ton basis and/or downtime for liner replacement would be to a high.In other words, solid rubber has limits as any other material. However, 'SKEGA started to think, why not try to use the best properties of rubber as well as steel and combine the two materials together.Nearly 10 years ago SKECA started to test this concept in Rod Mills. A steel cap was vulcanized on to the leading face of the lifter bars, to be installed close to the feed end head (fig. 1)."

Jan 1, 1988

Carrying Energy ?Energy ?Power, data, signal, hydraulics, pneumatics? ?Needs to be conveyed from a stationary point to a system in motion ?Cable Carriers (steel and plastic), Festoon Systems, Cable Reels and Bus Bars Polymer Cable Carriers ?Life Line for modern machinery ?Transmitting power, data, signal, hydraulics or pneumatic energy ?Constructed and designed to work in harsh environments, at high speeds and to do this continuously ?Meet a wide variety of cable (Media) requirements ?Virtually maintenance free ?High efficiency

Nov 1, 2011

By J. P. Mogan, E. D. Dainty

Polynuclear aromatic hydrocarbon (PAH) levels were measured in underground mines in the vicinity of diesel vehicles equipped with several types of emission control hardware. In general, the emission control devices appeared to reduce PAH levels, but the companion mutagen study suggested that the reduction might not always be beneficial. All underground PAH concentrations were below the threshold at which a significant impact on health might be expected, but recent animal exposure studies have indicated that PAHs may not be the primary hazard from chronic diesel fume exposure.

Jan 1, 1994

By A. J. Faulds, K. C. Westaway, Z. Waszczylo

"PAH compounds have been found in the exhaust from all types of engines burning hydrocarbon fuels . They have also been found in the air over cities and in water. The authors report on a study to assess the concentrations of twelve different PAH compounds in several different environments in dieselized underground mines. In addition, the differences in the PAH levels and distributions in different mines will be demonstrated. Finally, the influence of blasting and the type of diesel engine used as well as the effect of catalytic converters in the exhaust system on the PAH concentration in the mine will be discussed.IntroductionMining methods have been altered significantly in the last 25 years; i.e ., the tools and machinery used underground have changed from electrically operated trains and other equipment to diesel-powered equipment. This has been done for several reasons: 1) economics, 2) convenience and 3) safety. Today, most mines are heavily committed to using diesel equipment.Although the introduction of diesel equipment has revolutionized mining methods and has been a tremendous boon to the mining industry, it has also created new problems. These problems arise because the exhaust from diesel engines contains several pollutants which can be hazardous to the health of the miners. These pollutants are CO2, CO, NO., SO2, oxygenated hydrocarbons produced during the buring process and unburned hydrocarbons. There are two classes of hydrocarbons, of which polynuclear aromatic hydrocarbons (PAHs or PNAs) are a part."

Jan 1, 1981

By Fernando Canales

In the last decade a great dealt of attention has been paid to the chemistry of polynuclear gold derivatives with a central heteroatom, not only from the experimental and structural but also from the theoretical standpoint (1). Interesting hypercoordinated species of the type [C(AuPR3)5]+, [C(AuPR3)6]2+, [N(AuPR3)5]2+, [P(AuPR3)5]2+ and [P(AuPR3)6]3+ have been described (2), apart from other complexes with more conventional stoichiometry, and all have in common the presence of gold-gold interactions of ca. 3 Å. Usually, the chemistry of the first row elements of the p-block is known to follow classical rules of bonding, and only in cases of extreme electron-deficiency has the traditional electron count to be reconsidered to account for special types of molecular or solid state structures. Many of these heteroatomcentered complexes are electron-deficient and the gold-gold interactions provide a significant contribution to their stability. The attraction between these closed-shell systems has recently captured the attention in inorganic and organometallic chemistry (1). P. Pyykkö has summarized the available theoretical and experimental evidence of intra- and inter-molecular interactions between heavy metal atoms, such as Au(I) (3). In general, when heavy metals are involved in such interaction, the closed-shell attractions are of metallophilic or van der Waals type, as has been found for d8, d10 coinage-metals, and d10s2 centers. Experimental evidence for the aurophilic Au(I)???Au(I) attraction is available from crystallography, NMR and Raman spectroscopies, and optical spectroscopic measurements of the interaction strength (4). It is manifested in molecular conformations with relatively close Au???Au interactions of ca. 3 Å, whose strength has been estimated at ca. 25-50 kJ/mol (5). These attractions are weaker than most covalent or ionic bonds, but stronger than other van der Waals bonds and comparable in strength to typical hydrogen bonds. The phenomenon cannot be satisfactorily explained by classical theories such as hybridization (3). From a theoretical point of view, the attractions close to equilibrium distances are caused by dispersive interactions together with relativistic effects (6). The attractive contributions are dominated by pair-excitations from the heavy metal, such as gold, strengthened by relativistic effects. In all the cases where there are inter- or intramolecular metal-metal attractions, the correlation effects are essential; if they are omitted, at the Hartree-Fock (HF) level, repulsive interactions are obtained (6). Hence, it is necessary to use at least second-order Møller-Plesset level (MP2) methods for the dispersive forces, which are included in the electronic correlation effects (7).

Oct 1, 2003

By Louis M. Perlman

CAN PRESENT TRENDS CONTINUE? Can population growth in the world keep going at the average rates of the last few decades, till, say, the year 2000? And beyond? At the same time, can we expect steady increases in mineral consumption per head, all over the world, as the living standards of many nations converge toward the living standards of North America? If they do converge? Does the total fund of world resources extend, with foreseeable techniques, to supplying the consequent demands for metals, non-metallic minerals and energy? Do we have the requisite economic and scientific techniques available to answer these questions? Certainly, we cannot forecast over decades with any certainty. There are many, of course, who seem to believe that by the simple fitting of trends, they can tell us something about the world and resource constraints in the year 2000, twenty-three years from now. It is significant that many studies of this sort have added sustenance to the 'doom-watching' fraternity of commentators. The reason is simple. The extrapolation of exponential trends into the distant future frequently leads to the most astounding and impossible scenarios. Another feature of exponential growth is the suddenness with which certain fixed limits are approached. It took world population two hundreds years to increase by 1/2 a billion, from 1650 to 1850. Yet some U.N. estimates suggest that the net addition to human population will be over 2 billion between now and the end of the century. Thus, the present world population would increase from a little under four thousand million today to rather over six thousand million in the year 2000.

Jan 1, 1977

By Kenji Koga

In order to derive the population distribution of gold nanoparticle morphologies as a function of size, highresolution electron microscopic (HREM) observations and structural analyses were done for over 4000 particles (3-18 nm) grown by an inert gas aggregation (IGA) source using helium. To obtain structural features threedimensionally and not to skip high-contrast images, twenty photos were taken for each particle by changing tilting angle of a specimen holder in combination with the through-focus procedure. For the reliable structural determinations, HREM images and their tilting sequences were directly compared with multislice-simulation results for icosahedral, decahedral and face-centered cubic morphologies, and finally the population distribution of each morphology was obtained as a function of size. In the present sample, icosahedral particles were dominantly populated over the whole observed size range and decahedral particles with non-spherical truncated bi-pyramid shape were secondly dominant. Even though a large number of sampling has been done, few crystalline particles were observed.

Oct 1, 2003

Located in Timmins, Ontario the Porcupine Joint Venture, a pooling of assets between two existing operations (the Dome Operation of Placer Dome (CLA) and the Hoyle Pond Operation of Kinross Gold Corporation) came about on July 1st, 2002; Placer being the manager of the Joint Venture with 51% ownership and Kinross with 49%. The formation of the Joint Venture was the realization of the dream of many who could envision the benefits of the whole area being operated as one entity ? the combination of the majority of assets in the Porcupine Camp into one venture containing tremendous synergistic potential of manpower, infrastructure, land tenure and exploration development. The name Porcupine in the gold mining industry brings with it the legacy of world class gold mines; the Hollinger, McIntyre and Dome with a proud tradition of excellence. The name Porcupine brings with it the legacy of over twenty individual mining companies in operation at any one time, producing over 65 million ounces of gold.

May 1, 2003

By A. R. Byers

"Porcupine Peninsular mine is at the extreme southwestern end of North peninsula in Night Hawk lake, Cody township, Ontario. It lies approximately 10 miles east of the gold-producing district of Porcupine.Gold in quartz veins was discovered on Gold -island in Night Hawk lake in 1906, the same year in which the now famous Porcupine gold camp was discovered farther west. Most of the claims now held by the Company were originally staked by Charles Auer in 1907, In 1910 when the level of the lake was exceptionally low, gold was discovered in a quartz vein near the shore and close to the present mine shaft.The mine is developed by a main shaft to a depth of 440 feet, with levels at 80, 180, 300, and 425 feet vertical depth and by a winze to 630 feet. A mill of 200 tons daily capacity was built during 1923, Production commenced on January 4, 1924, and continued without interruption to May 31; 1926, when operations were suspended due to a decrease in the grade of ore. Total production amounted to 27,416 ounces of gold from 99,708 tons of ore, an average grade of 0.275 oz. a ton. Diamond drilling and re-sampling of the mine during 1934 and 1935 indicated approximately 1,480,000 tons, having an average grade of 0.123 oz. gold a ton, above the 625-foot level."

Jan 1, 1954

By G. Armand, A. Noiret, D. Seyedi, J. Morel

"Clay formations in their natural state exhibit very favorable confining conditions for repository of radioactive waste because they generally have a very low hydraulic conductivity, small molecular diffusion and significant retention capacity for radionuclides. Nevertheless, one concern regarding the hydromechanical behavior around drifts in such claystone is the associated pore pressure field disturbance during excavation works. In the short term, the very low permeability leads to an almost “undrained” condition, meaning that the stress change due to face advance will create volumetric strains leading to an increase or decrease of pore pressure. If the effective stresses reach the failure level, the induced damage around these excavations might change the favorable properties of such formations. To demonstrate the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW) in the Callovo-Oxfordian claystone (COX) formation, the French national radioactive waste management agency (Andra) started in 2000 to build the Meuse Haute-Marne underground research laboratory (M/HM URL). The present paper illustrates observed pore pressure changes during excavation of drifts (˜5 m diameter), of micro tunnels (˜0.7 m diameter) and a borehole (˜0.15 m diameter). All these openings are parallel to the major horizontal stress at the main level of the M/HM URL. In drifts parallel to the major stress (i.e., when the initial stress field in the drift section is quasi-isotropic) an important increase followed by a drop of pore pressure is observed in the horizontal plane at the drift wall. These observations emphasize the impact of the in situ stress state and rate of excavation on the pore pressure and provide important insight of the hydro mechanical behavior of the COX claystone and the relationship between pore pressure and excavation induced fractures zone."

Jan 1, 2015

By H. Soltanzadeh

This paper summarizes semi-analytical and closed-form solutions that can be used to assess the poroelastic stress changes induced within a porous formation (reservoir) during a pore pressure change. Further, solutions are presented for the stress discontinuities at the interfaces between reservoirs and the rocks that surround them. When used in combination with rock failure criteria, these solutions enable relatively simple analyses of the potential for induced fracturing or fault reactivation within a reservoir or the rock immediately adjacent to it. The latter, in particular, is useful for assessing if the hydraulic integrity of the surrounding rock (i.e., the bounding seal) will be affected by a pore pressure change. The use of the approach presented in this paper is illustrated with an analysis of a pinnacle reef with dimensions and properties representative of reefs in the Zama oil field, northwestern Alberta, Canada. Scenarios of pore pressure decrease (during historical production operations) and pore pressure increase (during several years of acid gas injection operations) are analyzed, for three different idealizations of reservoir properties and geometry (two plane strain and one axisymmetric). These results suggest that that the potential for induced fracturing is not significant at any point within the reservoir or the surrounding rock for both the production and injection scenarios that were simulated. Similarly, fault reactivation was not predicted for the reservoir or any of the points that were analyzed in the surrounding rock. However, fault orientations having the greatest potential for reactivating during historical production operations were identified; thus, illustrating a means of using geomechanical models to focus geological characterization efforts on the features that are most critical to acid gas containment.

May 1, 2009

By A. Kraly, M. Complojer, P. Paschen, K. Gamweger, H. Antrekowitsch

Increasing quality of aluminium alloys and continuous optimization of the production process leads to an improvement of the gas purging systems. The application of porous plugs for the treatment of liquid aluminum is nowadays not widely used in the aluminium industry especially in Europe. The Department of Nonferrous Metallurgy and the Christian Doppler Laboratory of Secondary Metallurgy of Nonferrous Metals intensified the research and development of refining and alloying processes by gas treatment during the last years. CFD-modeling supports these experiments, which should lead to lower hydrogen content, lower suspended particles and a better distribution of alloying elements in the melt. Different parameters such as temperature, bubble size, gas amount and which kind of gas is used influence the quality of the products.

Jan 1, 2006

By I. S. Parrish

The Sullivan Mining Group has been exploring the mineral deposits of the Mount Pleasant area of southern New Brunswick since 1967. Sullivan geologists have logged over sixty miles of drill core, mapped over five miles of underground workings and studied numerous surface exposures. Several mineralized zones have been defined and two higher-grade porphyrytungsten bodies delineated. Within these bodies, wolframite occurs as disseminated specks and grains up to one-half inch in diameter. The host rock is a brecciated rhyolite porphyry that has intruded quartz-feldspar porphyry of Mississippian age . The host rock is itself intruded by an acid porphyry called transition rock and is underlain by a microgranite. The mineralized zones, host rock, transition rock and microgranite are all thought to be derived from the same magma, and to represent progressive fractions from that magma.

Jan 1, 1978

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

By D. D. Campbell

"The Port Radium mine of Eldorado Mining and Refining Limited lies on the western tip of a large peninsula midway up the east shore of McTavish Arm, Great Bear Lake, about 30 miles south of the Arctic Circle. The mine is serviced by air, 950 miles from Edmonton, and by water, 1,380 miles from Waterways, Alberta.The veins were found, and the copper and cobalt minerals in them reported, by J. MacJntosh Bell of the Geological Survey of Canada in 1899. The veins were investigated by Gilbert Labine and E. C. St. Paul in 1930, and as a result of their work the Eldorado mine was brought into production in 1934. It produced silver and radium ores until 1940, at which time, as the silver orebodies had been mined out and the market for radium was negligible, it closed down. Early in World War II the need for uranium for the Manhattan Project was emphasized, and the mine was reopened in 1942. As a security measure Eldorado Mining and Refining was created a Crown company in 1944. The Port Radium mine has continued to be one of Canada's principal producers of pitchblende concentrates, and to date has about 25 miles of underground workings developed on fourteen levels.Regional GeologyThe general geology of the McTavish Arm area was mapped by D. F. Kidd in 1932 on a scale of one inch to four miles. A great deal of more detailed work has since been done by geologists of the Geological Survey and of Eldorado. The entire area at the end of McTavish Arm lies within the Precambrian Shield immediately east of its western margin. Most of the area is underlain by granitic masses which have intruded a sequence of late Precambrian sediments, volcanics, and hypabyssal intrusives. The pre-granite rocks now occur in extensive, irregular patches and pendants within the granite. Pitchblende deposits have been found in the district in all rock types, but the most favourable host rocks are the cherty sediments of the lower Echo Bay group."

Jan 1, 1949

By F. A. McLean

At the Annual Western Meeting held at Blairmore, Alta., October 1924, the writer presented a paper drawing attention -to the advantages of portable gas-driven equipment for developing isolated mining properties. This type of equipment was at that time practically in its infancy and the details of results actually accomplished were somewhat meagre. During the last year or so a number of these plants have been installed so that it is now possible to offer more definite information regarding the actual mining progress accomplished with such plants and their cost of operation in various parts of the country. This paper has been written with the idea of reviewing the work done during the past year, and to supply data which may be of interest to those wh9 are confronted with the problem of selecting equipment for development or assessment work. Because drilling operations play such an important part in mining, one of the first problems that usually confront the prospective? mine owner is the selection of the proper com-pressed-air plant. The size and type of equipment and the method of driving it require careful consideration. The size and type of equipment is determined largely by the funds available, transportation facilities, and the speed with which the programme of development is to be carried out. The selection of the proper method of drive usually depends on local conditions, such as the relative cost of various fuels, and has an important bearing on operating costs.

Jan 1, 1926

By W. A. Toohey

Introduction From the earliest times it has been an inherent trait of man to build or create something for his own use or convenience. The need of some form of shelter other than that of the caves led him to bind together stones and other materials to form walls for his abode. Moistened clay which hardened upon drying was no doubt first employed. The Assyrians and Babylonians appear to have employed it or the bitumen found in their country. The early Egyptians and Greeks used some form of lime in their construction work. In addition to these shelters, other structures received attention, and, long before the Roman Empire was established, the Carthaginians made use of a natural cement as binding material. Portions of an aqueduct, seventy miles long, in Northern Africa, built in those early days, are still in use. The Etruscans were the first people in Italy to employ a mortar in their buildings. The Romans, learning the art from the Etruscans, improved the mortar by using a mixture of lime and volcanic ash, called 'puzzolan', and built not only roads but those famous structures, the ruins of many of which exist to this day. The Pantheon at Rome, built by Hadrian about 120 A.D., is perhaps the finest example of the early use of cement in building construction. With the decline of the Roman Empire, the art of making cement seems to have been lost, and for centuries the builders of Europe used only lime mortar. Pure limestones were selected for making the lime and great care was taken in the preparation of the mortar, the supply for one year being made the previous season and left to thoroughly slake or 'ripen' in pits covered with earth. The mortar thus produced gave excellent service above ground or where it was exposed to the hardening action of the air, but would not harden under water.

Jan 1, 1927

By B. R. MacKay

Introduction Of all Canada's mineral resources, its coal deposits have probably received the most continued attention by the Geological Survey since its inception ninety years ago. A casual review of the many geological maps of coal areas by the Geological Survey will show how geological and topographical detail on the maps has gradually increased to meet the ever urgent demands of the mining industry. In the early stages of exploration, the mapping done, especially in the coalfields of the Rocky mountains, was largely of a reconnaissance nature. On these maps the topographical relief, where shown, is indicated by form lines or by hachures, the boundaries of the coal-bearing formations are only approximately defined, and the geological structure of the coal seams is illustrated by one or more generalized cross-sections. Once mining development on a coal area began, there arose a demand for more detailed maps. To meet this need, topographical and geological maps on a scale of one inch to a mile were made, in which the ?topographical relief is shown by contour lines having generally an interval of 100 or 200feet. On the geological maps, the boundaries of the formations are accurately delineated, and the geological structure of the area is illustrated by one or more structure sections drawn across the area, which show the position and attitude of fault lines, the crests and troughs of folds, and the attitude of the various formations (See maps of Costigan Coal Field, 1905, and Cascade Coal Basin, 1907, by D. B. Dowling).

Jan 1, 1932