Search Documents

?Hydrothermal breccias-genetic models ?Deep drilling-underground potential ?Deposit variety-test new ideas Exploration Summary

May 1, 2006

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951

By R. B. Hyde

"Severe drilling conditions and difficult mud problems are briefly out-lined as the major cost items in all production operations. The chief problems discussed are abnormal pressures, high temperature, trouble-some shales, and low rates of penetration. These problems have been eliminated or greatly reduced in many areas by• the proper application of recently developed drilling mud products and techniques. These severe problems and their solutions are discussed generally: the application of high-density weighting materials to overcome abnormal pressures; surfactant muds with sodium polyacrylate as a solution for deep and high-temperature drilling; shale control muds and new dispersants for severe shale problems; and low-solids emulsions and •extreme-pressure lubricants for greatly improved rates of penetration."

Jan 1, 1959

By L. C. So, S. Faucher, S. Mostaghel, D. Sauter, S. -Y. Oh, S. K. Lee

"Molten material from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of heat. Traditional handling methods of slow air cooling or water granulation do not allow for the recovery of heat from slag and matte. Furthermore, water granulation adds an inherent safety risk of explosions. Recently, there have been numerous studies into processes attempting to recover waste heat. However, most of them have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple dry atomization system that allows for heat recovery while eliminating the use of water. Comparisons of pilot and commercialized dry atomization and heat recovery technologies will be presented and challenges of these technologies will be highlighted.INTRODUCTION Slag has traditionally been regarded as an undesired waste product from smelting operations with slag management focused on removal and disposal of “waste”. Over 500 million tonnes of slag are produced per year, carrying with it ~220 TWh of energy (Barati, Esfahani, & Utigard, 2011). Depending on the process, the energy content of slag ranges from 10-90% of the total energy input (Barati, 2011, Rodd, 2010). There has therefore been great interest in recovering energy from slag. Slag handling methods can broadly be classified into three categories: (1) dumping and slow cooling, (2) wet granulation and (3) dry granulation. As discussed below, only dry granulation routes are amenable to heat recovery. Slag dumping involves the slow cooling of molten material and crushing of the resulting solid. In this process, slag is dumped on the ground directly from furnaces or transferred to slag pots that are moved by rail or haulers and then dumped on the ground. The molten material is left to cool and solidify until it can be broken and handled by heavy machinery."

Jan 1, 2017

By E. R. Landry

This paper reviews the current state of electric furnace technology, with emphasis on some of the more recent developments. A large section of the paper is devoted to the use of increasingly high power inputs by arc furnace operators. Operating practices are then covered, including some of the newer techniques which have been tried.

Jan 1, 1967

By W. R. Hopkins, J. A. Davis

"This paper presents a discussion of the mechanisms by which aerosols of the process electrolyte are entrained into the breathing environment of copper, Zinc and nickel eIectrowinning tankhouses. Literature outlining the health effects associated with worker & posure to the acidic and metallic contaminants found in the airbome aerosols is summarized and compared with existing North American regulations.A brief review of the existing technologies for the source reduction of these aerosols is presented. This paper outlines the industry experience with use of covers, balls, beads, shapes, fixtures and chemical surfaetants. Each of these devices is ranked according to its effusiveness in the process in which it is used, and rated according to its operator acceptance.The various forms of existing in-plant ventilation systems are reviewed with a discussion of their relative merits and effectiveness. Actual experience is related, detailing the methods of testing for ambient contaminant levels in a variety of tankhouse environments. Guidelines are provided for the site and process specific criteria which govern the selection and ultimate effectiveness of a particular form of ventilation system.Finally, actual project experience is cited in which hydraulic modelling is used a design tool in tankhouse ventilation design. These projects include the upgrading of existing traditional ventilation designs, and the ''grass roots"" design of a more efficient aerosol source control system to be used in high altitude, cold weather sites."

Jan 1, 1994

By Simon P. Fricker

Gold drugs have been used for the treatment of rheumatoid arthritis since the mid 20th century as disease-modifying antirheumatic drugs (DMARD) class. Methotrexate is often the preferred DMARD, and with the advent of new therapies gold drugs are now used infrequently. Since the introduction of auranofin in 1985 there has been no new clinically approved gold drug. In spite of this apparent lack of progress there has been a great deal of interest in the use of gold compounds for cancer therapy and early promising indications were achieved with a gold phosphine complex [Au(dppe)2]Cl. This compound was not entered for clinical trials, however, due to problems with cardiotoxicity highlighted during pre-clinical toxicology studies. Gold(III) is isoelectronic (d8) with platinum(II) and likewise forms square planar complexes. It is therefore tempting to speculate that such complexes would have similar antitumor activity to cisplatin. In order to stabilise the gold(III) oxidation cycloaurated complexes were synthesised with a single mononegative bidentate ligand, damp, (2-[(dimethylamino)methyl]phenyl), and two monodentate anionic ligands e.g. Cl or acetate. The damp ligand forms part of a five-membered chelate ring. The monodentate ligands are readily hydrolysed and are available for substitution. These compounds had limited anti-tumor activity in in vivo against human tumor xenografts. Mechanistic studies indicated that these compounds had a different mechanism of action to cisplatin. An alternative molecular target for these compounds is biologically important thiol-containing molecules such as the cysteine protease cathepsin B. Modifications were made to the Au(III) damp structure to give compounds with a six-membered chelate ring. These compounds were shown to be inhibitors of cathepsin B. Compounds were also tested for cytotoxicity against a panel of human tumor cell lines. Three compounds were selected for further evaluation against a human colon tumor xenograft. The compounds showed modest anti-tumor activity but with no marked improvement over the parent Au(III)damp complexes. Initial indications are that Au(III) compounds targeted against disease-specific thiol-containing biological molecules have potential as drugs, particularly for cancer. However, further work is required to produce a target-specific drug with a suitable pharmacological activity and toxicity profile.

Oct 1, 2003

By W. B. Timm

Introduction In preparing this paper on Recent Developments in Gold Milling Practice, the idea occurred to me that possibly the best way to deal with the subject would be to take you in thought on a visit to the principal gold mining camps of the Dominion, starting at the east and finishing up in the west, and noting, as we go, the outstanding improvements that have been made in the last few years in the practice of gold milling. Before beginning this tour, I desire to emphasize the debt this country, and particularly our mining industry, owes to that body of trained and experienced men, little heard of, but who, working quietly on their problems, are responsible for these improvements. The metallurgists, to whom I refer, have solved many difficult problems for the mining industry, in connection with the treatment of our complex ores; for instance, the silver-cobalt ores of the Cobalt district, the gold ores of the Porcupine district, the gold-telluride ores of the Kirkland Lake? district, the copper-gold ores of Noranda, the arsenical-gold ores of the Beattie mine, the copper-zinc ores of Flin Flon, and the lead-zinc ores of Kimberley. In doing so, they have maintained the high technical standards of the profession, and the practices thus evolved are noteworthy for their high degree of efficiency. When the price of gold increased from $20.67 to $35.00 an ounce, what had formerly been thought to be a low tailing became almost an ore, so that the metallurgists are now busily engaged upon the problem of putting this railing back in its proper place of being a tailing once more, or from its value, at the present price, of anywhere from 50 cents to a dollar or so per ton, to a few cents per ton. Owing to the changing prices of the metals in the world's markets, still greater improvements in metallurgical practices are imperative. An important contributory factor towards improvement in ore dressing is the aid furnished by the microscope in the examination of ores and mill products. By making possible the determination of the mineral constituents of the ore, their association, and grain size, it gives the investigator a knowledge of his problem, before he does any actual test work. In the Mines Branch laboratories at Ottawa, its use has enabled us to predict how an ore should respond to various methods of treatment.

Jan 1, 1935

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By W. M. Armstrong

THE GROWTH of the major iron and steel industries on this continent and in many European countries was based on the use of as-mined, high-grade, lump iron ores and on the availability of metallurgical coking coals. The modern coke-fired blast furnace was developed for such materials and is one of the most efficient of ail pyrometallurgical processes. Most of the impure pig iron produced by blast furnaces was converted to refined steel by the Bessemer process in the years prior to 1900 but, when large quantities of low-cost steel scrap be-came available, the more flexible open hearth process was adopted by most large steel producers on this continent. Although this pro-cess has many desirable metallurgical features, the thermal efficiency is low, the capital cost is very high, and the method of charging scrap steel is inefficient by modern standards of material handling. In recent years several conditions have arisen which have stimulated the development of many new pro-cesses and the re-examination of the existing smelting and steelmaking techniques.

Jan 1, 1958

By T G. Callcott

Australian coking coals are either class 434<tlj534<2l, at Port Kembla, or 634<3> at Newcastle. The former yield good blast-furnace cokes; the latter yield poor ones. However, increases in conventional strength indices, by methods applicable with normal coking ovens, seem unlikely to be economically attractive. Characterization of the coals has enabled an "economic" blend to be developed in the Newcastle area, and this has affected mining, preparation and handling operations. Coking studies have led to a specification for the making of strong coke, especially from the high-volatile Newcastle coals. Continuous coking studies, developed from the efforts to make very strong coke, have taken two directions. Firstly, coking thin layers of coal on strands; secondly, coking, in various types of vessels, compacts of coals with or with-out the inclusion of non-coking coals, iron ores or other inert materials. Gas, "sand" and hot metal coking have been tested for use in compact coking. Particular attention has been paid to pellets of coal and ore. The probable industrial problems in adopting any of the ideas are presently being examined.

Jan 1, 1963

By H. C. Cooke

This paper will discuss two comparatively unrelated subjects; first, a general review of the advances made at the more important properties in the last year; and second, a statement of the conditions controlling the deposition of the copper ores in the Rouyn area, as determined by last summer&apos;s field work. FIRST PART Development has been very rapid since I stood before the Institute one year ago to discuss this same subject. Then, there were many properties on which gold had been discovered, any of which might develop into a mine. Further work has eliminated the most of them as possible mines, or at least has shown that before they can attain that status further discoveries must be made on them. Then, all gold veins held forth much the same promise; now the indications are that one particular type of gold vein is of greater prospective value than others. Then, all eyes were turned toward gold as the metal of prime economic importance; now copper has taken the centre of the stage, and gold is distinctly in the background.

Jan 1, 1926

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By W. Tse, D. Wong

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run of mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamond and iron ore industries but lab scale and pilot test work has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS. This paper reviews historical dense media systems, results from the pilot scale Condor DMS system as well as associated laboratory heavy liquid separation (HLS) test work.

Jan 1, 2014

By Ernest A. Hodgson

A SERIOUS hazard which must be faced in some mines, though quite absent in others, is that of rockbursts. Bursts cannot be wholly avoided in such mines, but the hazard would largely disappear if they could be predicted. The problem of prediction resolves itself into that of measuring pressure in the mine and determining when that pressure nears a critical value. The geophysical approach to the problem lies in discovering some physical property of the rock, which varies with pressure, which can be measured for rock in place, and for which the indication of critical conditions is sufficiently definite and open scale. A physical property, suggested first in connection with earthquake pre-diction, is that of sub-audible snapping. It was argued that, as the pressure grows, the rock probably yields microscopically and that minute snapping occurs which is so faint as to be inaudible to the unaided ear. Experience has proved this to be the case. Following other earlier work begun early in 1939, experiments with this method were initiated at Lake Shore Mines in 1941, and equipment was slowly being developed in practice when, fortunately, it was found possible to by-pass this tedious development programme. Experiments with sub-audible snapping in mine rocks had been carried out by Dr. L. A. Obert of the U.S. Bureau of Mines and his associates over a period of about four years. An amplifier and a recorder were developed, each reasonably satisfactory in practice. Lake Shore Mines offers a tempting field for rockburst research. Dr. Obert was invited to test his equipment in this and other mines in Ontario and did so. As a result, he and the administrative personnel of the Bureau became interested in the Lake Shore experiments co the extent of most generously arranging for the manufacture of sets of their own designed equipment for use in this programme. The first three sets of recorders were ordered at once and were delivered in May, 1942. A second group of three sets, incorporating various improvements indicated by experience both in the United States and in Canada, reached Kirkland Lake in April, 1943. The pick-up devices, known as geophones, were made in the electronics laboratory at Lake Shore by Mr. Zack Gibbs, who has had charge of all the instrument development in this re-search.

Jan 1, 1943

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By M A. Notte

Sand casting of steel is a process that offers the greatest design flexibility and highest metallurgical versatility. However, competition from other methods of fabrication is quite keen, constantly forcing the steel casting industry to the production of better quality castings at lower costs. New methods and materials have been put to use in the last ten years by foundries everywhere. This paper, in the form of a progress report, deals with new methods, processes and materials used by Canadian steel foundries for regular production, as well as with developments still in the initial but promising stages. T HE casting of steel to shape is the most direct method of producing steel parts in their final form. It is a basically economical process both as to cost and production time; it is also a process that offers design engineers the greatest flexibility and highest metallurgical versatility. In North America, the steel casting market has a normal yearly sales volume of 1,500,000 tons. In decreasing order, the largest customers are the railroads, construction machinery and earth-moving

Jan 1, 1965

By U. Erb, L. Monaco

"Electrodeposited nanomaterials are increasingly implemented in advanced industrial applications in the aerospace, automotive, defence, electronic and energy sectors due to their outstanding physical, chemical and mechanical properties, including increased strength and wear resistance, and superb magnetic properties. As with the development of any class of new materials, the corrosion behaviour of these electrodeposits requires considerable attention. This presentation reviews major developments in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites over the last 20 years, with emphasis on how their intrinsically high density of intercrystalline defects does not compromise their corrosion resistance as initially expected.INTRODUCTIONOver the past 20 years there have been considerable advances in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites. In this paper, the corrosion properties of nanocrystalline nickel, cobalt, zinc, and copper and some of their alloys are reviewed with emphasis on how a reduction in grain size affects their corrosion behaviour in different environments.It is possible to synthesize nanocrystalline material with microstructural refinement down to the range of 1 to 100 nm using a large number of processing methods. There are five basic synthesis methods that can be used to classify the different techniques: vapor-phase processing, liquid-phase processing, solid-phase processing, chemical synthesis, and electrochemical synthesis. Depending on the synthesis method, different microstructures (equiaxed, textured), shapes, and forms (films, particles, bulk material) may be produced. In addition, other factors may be introduced (eg. residual porosity or amorphous phases), aside from microstructural refinement, which can contribute to the observed properties (Erb, 2010). In order to interpret and categorize the resulting microstructures, a dimensional structure modulation scheme was introduced by Siegel (1996) in which zero-dimensional nanomaterials refer to individual particles, clusters, etc. One-dimensionality results from a layered (less than 100 nm thick) structure. Two-dimensional nanomaterials are thin, layered structures containing grains (less than 100 nm) within each layer. Finally, three-dimensional nanomaterials are bulk structures with an average grain size less than 100 nm."

Jan 1, 2012

By G. J. Desroches

"In order to improve zinc plant productivity, areas of low efficiency were identified. As a result, solution purification was improved, additional dust precipitator capacity was made available and a new zinc casting plant was installed. The effects of these and other changes are discussed and the expenditure and benefits reviewed. HistoryThe operation of the Flin Flon metallurgical complex including an electrolytic zinc plant commenced in October 1930. The design of the zinc plant was based on that of the Commonwealth Mining and Smelting Company at Trail, British Columbia, the Anaconda Great Falls Montana Plant and the Electrolytic Zinc Company plant at Risdon, Tasmania.The plant began with a design capacity of 60 tons per day and currently produces 255 tons per day. Since plant start-up, approximately 3.5 million ton s of zinc metal have been produced, most of it exceeding special high-grade specifications.IntroductionThe facility incorporates the basic process steps of roasting, leaching, purification, electrowinning and casting. Figure I details the flowsheet. During the late 1970s, management recognized that in order for the zinc plant to continue operating, it was necessary to introduce cost-effective practices.Study groups, consisting of design engineers and operations personnel, were formed to investigate the details of plant revisions.The objectives were to improve productivity by reducing manual labour, reducing energy usage, increasing zinc recovery, increasing metal output and reducing costs.This paper details the changes made during the period 1979to 1986 and shows how these changes have affected the productivity and economics of the zinc plant operation."

Jan 1, 1988

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016