Search Documents

By E. Poiate, P. R. Cabral, A. V. N. Santos, P. V. M. Costa, C. S. Amaral, A. M. Costa

This paper discusses the design of underground salt caverns, opened by solution mining, for the production of brine and storage of natural gas under high pressures. The caverns are located in the salt basin in Maceio City, Alagoas State, at the northeast region of Brazil. Special attention is given to the geomechanical structural design of the caverns using computer codes specially developed for the simulation of excavations in salt rock formations, considering validated constitutive creep laws under different initial stress states and temperatures. The behavior of sedimentary rocks intercalations presented in the salt layer is simulated using elastic-plastic models. The excavation of the caverns by solution mining is also simulated starting from a geostatic initial equilibrium state of stresses, with a unique formulation only implemented in these computer codes, without the need of the application of boundary stresses to the model in order to develop the initial state of stresses. These computer codes have being used in the design of several clusters of caverns for brine production used as raw material of Poly Vinyl Chloride (PVC) of the Chemical Industryin Brazil. These computer codes and methodology were also applied to the design of the underground conventional potash mine in the state of Sergipe, overlying tachyhydrite and carnallite with very high creep strain rate. They have also been used in the design of the pre-salt oil wells through thick layers of stratified salt rock in Santos Basin, for the exploration and production of the pre-salt reservoirs in Brazil. The constitutive creep equations implemented in the codes are based on a double mechanism creep law. The creep constants adopted in the simulation are taken from a previous investigation carried out on an experimental panel of the potash mine, considering the stratified geology with different salt rocks of the basin where the mine is located. These constants were also obtained by lab tests under different confined and differential stresses and temperatures.

Jan 1, 2015

By Veronique Falmagne

"In 1987 the only knowledge available of the Ansil orebody was that it was high grade, deep and relatively small . High stresses were also anticipated because there had been rockbursts during shaft sinking and destress blasting had been necessary (Fig. 1). From the design, through the development and now in the mining stage, rock mechanics and microseismic monitoring have been used to maximize recovery and safety and minimize dilution. Examples are given of the use of a microseismic monitoring system in the early stages o f mining. This paper also presents a review of the mine's in situ stress measurement campaign, cable bolting practice and backfill procedure.The Design PhaseAfter the initial mapping and classification work, preIiminary numerical modelling was performed using assumed stresses of ov = oH and oH = 3ov• The empirical Mathew's analysis was then used to optimize stope dimensions based on geomechanics data available at the time (Bawden et 01., 1988; Falmagne, 1987; Potvin et 01., 1988). Because of high stresses predicted by numerical modelling and a brittle, strong and relatively unfractured host rock which was believed to be rockburst prone, it was decided to mine without temporary or permanent pillars. However, in order to satisfy production rates, the orebody had to be broken up into two horiwns separated by a triangular pillar (Fig. 2). The final mining sequence is shown in Figure 3.The Development PhaseAt this point, based on work accomplished to date, including mapping and observations from drifting and modelling, the following problems were identified: (1) flat backs in the hangingwall andesite were thought to be highly stressed; (2) flat backs in weak massive sulphide ore would also be subjected to high stress and be difficult to support; (3) the felsic dyke was noted as a "" stress raiser"" , because activity increased as drifts approached it; and (4) chlorite coating of joints in the hangingwall was thought to be an important factor in reducing their stability."

Jan 1, 1991

By J. K. Van Beek

The Deep Underground Science and Engineering Laboratory (DUSEL) is a scientific facility that will be placed in the deeper reaches of the Homestake mine, Lead, SD. Our team of geologists and engineers is carrying out the first scientific project awarded to the site ? Towards a Transparent Earth. Taking advantage of the thousands of open exploratory and sand-line holes, we are installing the beginnings of a seismic observatory. Each installed station consists of a 3-D accelerometer package and a 1 nanoradian 2-D tilt meter. In order to allow for a variety of monitoring and characterization studies, the array instruments are sensitive over the frequency bandwidth of 0.2 - 1 KHz. Three, three component accelerometer stations are currently installed ? in a 140 m deep bore beneath the slurry pump house, and in 12 m deep bores on the 2000-foot level, 800 and 400 m from the Ross shaft. There is a tilt-meter installed at each 2000 level station. These installations are in 150 mm diameter sand-holes. From the currently installed tilt sensors we are investigating solid earth deformation as a response to tidal potential. The accelerometers are being used to locate and characterize events associated with mine dewatering and rehabilitation.

May 1, 2009

By M. H. Rana

"A survey of our knowledge in the field of rock mechanics is presented from the viewpoint of applications in the mining industry. Aspects of rock mechanics of special interest to the industry are enlarged upon, with emphasis on the avoidance of over-generalization. The relationship between fundamental and practical rock mechanics is discussed, and the need for cooperation between the university and industry to further our knowledge of -useful rock mechanics is emphasized. An attempt has been made to establish the scope of rock mechanics, as applied to problems in the mining industry. This is brought about by projecting rock mechanics as a tool to be intelligently used rather than magic, capable of producing ""miracles."" Continued education is important for individuals engaged in the application 0f rock mechanics in the mining industry. The scope of this education is discussed from a viewpoint of better communication between industry and the education and/or re-search establishments engaged in this work.Finally, the dangers of over-emphasis on rock mechanics are mentioned, but a justification of the in-vestment in rock mechanics programs in mines is also presented."

Jan 1, 1966

By K. G. Davies, M. J. Royea

"A major program of pillar recovery at the Sullivan mine has been assisted for the past several years by a concerted series of rock mechanics investigations. The object of these investigations is to measure the parameters of rock behaviour which influence pillar mining. This quantitative information is then used in the design of mining methods appropriate for various conditions.Instrumentation to measure absolute rock stress, changes in rock stress and the gross deformation of rock masses has been developed. Various instruments are described, as are instrument evaluation procedures and typical test results. The data from underground measurement projects have been used to modify pillar extraction sequences along re-treat fronts. Rock mechanics information from individual pillars has been incorporated into the design of mining methods to suit particular circumstances."

Jan 1, 1968

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By Chas. L. Emery

"The laws of rock mechanics apply equally well to all rock structures, and open pits are not exceptions. The concepts and some arguments about the emphasis to be placed on various aspects of open-pit design are discussed in this article.RocksROCK can be described as a granular material consisting of grains and glue. The grains may be fragments of other rocks or polycrystalline aggregates. The glue may be ferruginous, calcareous, argillaceous, siliceous or other material connecting the grains. In a crystal intergrowth, the outer layers of the crystals in contact with each other may be considered to act as a glue. Water may be a glue in clay or a grain in a crystal structure. Air and other fluids or gases are grains if they occupy spaces in a granular mass. Such grains are functional either chemically or mechanically or both."

Jan 1, 1966

By Jean-François Lessard

The performance of rock pass systems has a significant contribution to the economics of underground mines. Operational concerns include hang-ups due to arching of material, blockage and degradation of the rock pass. This papers presents the preliminary results of a comprehensive rock pass database on the engineering and operation of rock pass systems in Quebec underground mines.

May 1, 2002

By A. Brown

IN INTRODUCING the subject of rock pressures, it may safely be assumed that mining men are only too familiar with the physical effects of strata stresses that accompany the extraction of minerals. It may be further assumed that they have, as individuals, arrived at certain conclusions regarding their nature, based upon years spent in observing such phenomena and in learning how to continue mining in spite of them. Such hardly won experience forms the core of what is often referred to as 'pit sense'. This essential type of knowledge is not ?based on theoretical considerations, nor can it be found in text books. It is highly individualistic in nature and almost impossible to pass on from one generation to another in terms of precise rules for guidance. It is this aspect of individual judgment based on practical experience that has led to the significant phrase The Art of Mining.

Jan 1, 1956

By B. H. Kim

It is hypothesized that the standard approach adopted to characterize the ground and to determine the rock strength properties at depth are flawed and generally tend to underestimate the rock strength and possibly the stiffness, particularly when the rock mass is characterized as massive to moderately jointed or blocky to very blocky. It is therefore necessary to conclusively established that the hypothesis, that the rock strength in highly confined rocks is greater than generally anticipated, is actually valid and generally applicable, and then to develop new procedures to establish rock parameters that can be reliably used for the design of deep excavation.

May 1, 2009

By K. Ogawa, T. Yokoyama

Hydraulic fracturing technique, an applied technique to cause tensile fractures to rock by injecting water pressure to a certain closed section of the borehole, is a measurement method of in-situ rock stress. This technique has the highest track record for techniques used in sub 1000 meter. A feature of this technique is comparatively simple and easy for in-situ stress measurement, because the measurement is applicable when a drilled borehole is available. The predominant advantage of this method is that elastic constants such as Young’s modulus and Poisson’s ratio are not required for determining the value and direction of initial stress. The factors to determine the stress state are the water pressures of re-opening and shut-in of fractures around the borehole wall and its directions. With conventional methods, however, the accuracy of the derived stress states from the observation equations was often adversely affected by the lack of consideration of the remaining water pressure in fractures and insufficient stiffness of the pressurization system. We have developed a new hydraulic fracturing system based on a new test method concept overcoming these defects, and applied to a 300 meter deep borehole in granite. The most important improvement of the new system is an employment of a syringe pump which enables an accurate flow control of fluid with less than 1ml/min in the pressure of 30MPa. Therefore the new test system has a quick response for pressurising in the interval zone, and the measured data was confirmed extremely accurate.

Jan 1, 2015

By K Morrison

Different individuals have calculated the boundary stresses around elliptical openings in an infinite elastic medium for various conditions of loading. With caution, such calculations are useful in indicating stress trends in mining. This paper illustrates an application to caving operations and suggests that abnormal field stress would have an adverse effect. Introduction GELDART and Udd (1), applying elastic theory, confirmed, and set out graphically, the stress distributions on the surface of elliptical openings with axis ratios varying from 1.0 (a circle) to infinity (a crack). The loading conditions varied from uniaxial to hydrostatic, and inclinations for the opening, with respect to the stress axis, varied from 0° to 90°. As most mine openings can be generalized into this elliptical conception, the usefulness of the presentation lies in the fact that given reasonable estimates for the stress ratio, the axis ratio, and its inclination, then the trend in stress concentrations as an opening develops can be readily approximated.

Jan 1, 1964

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By Ralph H. Cleland

Introduction The mines of northern Ontario have entered the class of deep mines. It has often been asked: How deep can operations be carried on? What will the temperature be? This paper is a résumé of a brief survey of rock temperatures made by the Ontario Department of Mines during the year 1932. Present temperatures were recorded and the geothermal gradients that now exist were determined. No alarming situations were found, but many interesting ones have been noted. Northern Ontario mines are fortunately situated as compared with most deep-level mines of the world. The mean yearly temperature, as determined from meteorological records of the Federal Department of Marine, is from 33 to 38 degrees Fahrenheit. The tables on the next page show the temperature range in and about our mining camps ( l ). As no exact figures were obtainable for Kirkland Lake, the data for Iroquois Falls, which is about 50 miles northwest, were taken as applicable there. The figures for Timmins were checked against those of Cochrane and Iroquois Falls and found to be very similar, so that the Cochrane data may be used for the Porcupine camp. The yearly mean temperature is considered to be 33.5 F.

Jan 1, 1933

By M. F. Goudge

ROCK wool, one of the most recent additions to the list of Canadian-made, insulating materials, is a soft, light, fibrous material consisting of interlaced, flexible, glassy fibres so exceedingly fine that, individually, they are almost invisible to the naked eye and will float in air. In the process of manufacture, a suitable rock, generally a self-fluxing argillaceous dolomite consisting of nearly equal proportions of acidic and basic constituents, is melted to a completely fluid state and then converted into fibres either by a blast of steam or air, or by a mechanical device. The increase within the past five years in the number of plants in the United States making rock wool and slag wool has been remarkable, especially in view of the depressed conditions prevailing 'with most industries during this period. In 1930, there were only 8 plants reporting production of .these materials, whereas at the present time there are 44 plants in the United States listed as making these products, and there are 3 plants in Canada. In 1929, the total sales of rock-wool products in the United States amounted to-$2,377,324. In 1934, according to the National Rock and Slag Wool Association, 26 member companies reported sales of $3,695,405, and in 1935 the sale's of 30 member companies had a value of $5,571,469. The establishment of the rock-wool industry in Canada followed the publication in 1931 of a report (1) by the Mines Branch, Department of Mines, Ottawa, in which was set forth the results of field work and laboratory studies which indicated that large deposits of rock in the Niagara peninsula, hitherto regarded as valueless, were suitable for the making of rock wool. This report was supplemented in 1934 by another report (2), giving the results of further laboratory and commercial-scale tests on the rock from these particular deposits, which proved conclusively that rock wool of good quality could be made from the rock in question.

Jan 1, 1936

By W. T. Robson

Introduction Ground failure, violent or otherwise, is a problem to be contended with wherever underground operations are carried out. The character and extent of the failure, whether superficial or of more serious proportions, is determined by a number of factors, among which might be mentioned: the depth and dimensions of the underground workings; the types and distribution of wall rocks; structural features of the ore and enclosing rocks; the degree of metamorphism; the dip of the orebody; concentration of mining operations; the rate of mining; the history of the excavations made on the orebody in question. This last factor implies the consideration of such points as the arrangement and distribution of stoping both past and present, the current sequence of scoping, the type and effectiveness of the support used in old and current workings, and the amount and distribution of unmined parts of the lode. With such a variety of conditions, it is only natural that the situation at one place in a mine will not be the same as that obtaining in another part of the same mine and, more than likely, will be quite different in another property.

Jan 1, 1946

By Jan Butra

Longstanding mining of copper deposits in the Legnica-Glogow Mining Basin, Poland has accumulated broad experience concerning the impact of geological and mining conditions on seismic and rockburst hazard. Methods of rockburst prevention for deep copper mines have been developed based on gathered data. Methods of rockburst hazard evaluation and rockburst control constitute a set of rockburst prevention measures. Due to their nature and location within the production process, prevention methods can be passive or active. Active methods of rockburst prevention consist of the liquidation of stresses in the areas where they are concentrated through controlled generation of rock-mass tremors and rockburst by blasting works (group extraction blasting, release blasting in the rock mass and pillars able to accumulate the stress, as well as in the roof and floor). Group blasting works as a basic method are very effective in copper mine conditions. Provocation of dynamic events makes it possible to control the timing of their occurrence. In Polish copper mines, all blasting works are made during the absence of miners in the mining fields. Daily distribution of both the number of recorded strong seismic events and volume of energy released, confirm the advisability of using this kind of rockburst hazard prevention. The rockburst hazard prevention methods developed over 40 years of copper deposit extraction are economically reasonable and offer sufficient effectiveness under high rockburst hazard conditions.

Aug 1, 2013

By D. M. Morrison

"Microseismic systems at five mines in the Sudbury Basin provide the basic data for Falconbridge Limited's rockburst research. Daily and long-term analysis of this data as well as underground observations has confirmed the fault-slip mechanism of rock bursting at three mines. A detailed analysis of the complete history of Falconbridge Mine is being conducted and Distinct Element numerical models are being used to simulate both the stick-slip behaviour of faults and the dynamic effects of the induced vibrations on rock and backfill. University research includes acoustic tomographic imaging of the rock mass based on seismic wave propagation and collection of full micro seismic waveforms to allow application of advanced seismic and statistical analysis techniques. INTRODUCTIONFalconbridge Limited currently has five mines operating in the Sudbury Basin: East, Lockerby, Onaping, Fraser, and Strathcona Mines, which along with the Falconbridge open pit produced 2.8 million tonnes of ore in 1986. The underground mines range from about 600 m to 2000 m below surface and one of the consequences of mining at these depths is the occurrence of rockbursts.Research into rockburst phenomena at Falconbridge began over 25 years ago and research is continuing in an effort to avoid the problem by improved mine design, to protect mine openings from damage by design of effective support systems and to better understand the processes which precede a major fault slip rockburst. Since the early 1980s, significant progress has been made due principally to micro seismic monitoring and advances in microcomputer technology coupled with detailed underground investigations.It is now possible to identify the fault-slip mechanism as the cause of many of the rockbursts which occur at Falconbridge mines. By gaining an understanding of effect of mining-induced stresses on the pre-existing geological structures, areas which may experience rock bursting can be identified and can be protected against severe damage by appropriate support techniques."

Jan 1, 1989

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009