Search Documents

By T. Macpherson

Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By Concentrator Staff

"IntroductionA brief literature search will reveal that the information available concerning rod mills and ball mills is quite extensive. This type of equipment is used to treat every element from antimony to zinc. The size and capacity of individual mills, the number of units employed, and the configuration of the equipment within a concentrator add another dimension to the possible scope of this discussion. It would be impossible to treat this volume of material with any degree of thoroughness.It is the intention in this paper to describe the simplest and generally the most typical circuit wherein a single rod mill and ball mill operate in parallel. Some of the subject matter will not be entirely applicable to every installation. However the principles should be generally relevant to most applications.Typical Circuit DescriptionFigure 1 illustrates the arrangement of the equipment associated with a rod-ball mill circuit.Ore is extracted from a fine ore storage bin (1) the capacity of which is large enough to allow .continuous mill operation independently of the mine and crushing plant production schedules. A number of feeders (2) may be employed to control the flow of ore to one or more feeder conveyor belts (3). In larger tonnage operations several such conveyors are employed at least one of which will be equipped with a variable speed control to allow adjusting of the amount of feed reporting to the rod mill. A rod mill feed conveyor (4) accepts all of the ore from these feeder belts for ultimate transfer to the rod mill. This conveyor is normally equipped with a weightometer (5) to monitor the flow rate of ore to the rod mill and ultimately to allow control of this flow. Typically these conveyor belts would be equipped with feed deficiency switches which would give a remote alarm of the fact that no ore is present on the conveyor. The conveyor belts are protected by underspeed monitors which will provide a remote alarm and automatic shutdown of the conveyor in the C'.'~nt that belt slippage occurs. Finally the belts are protected by monitors which will alarm and shut down a belt if it is not running straight in the idlers."

Jan 1, 1989

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end-use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here, we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilization to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilized to produce more effective dispersant systems which allow the preparation of added value, higher solids and finer particle size calcium carbonate slurry products. IntroductionConcentrated aqueous dispersions of fine particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently, more than 10 Mt of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e., its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximize the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimize drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilisation to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilised to produce more effective dispersant systems which allow the preparation of, added value, higher solids and finer particle size calcium carbonate slurry products.INTRODUCTIONConcentrated aqueous dispersions of fine, particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently more than 10 million tonnes of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e. its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximise the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimise drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003

By E. Paransky, M. Rigaud, G. Paschek, S. Palco

Some of the negative impacts of carbon addition on the strength of castables are yet to be overcome in order to fulfill its potential benefits for oxidation resistance. This paper reports the results of recent studies conducted at CIREP on the effects of different types of carbon additives on the thermo-mechanical properties of magnesia-based castables. Experimental techniques included measurements of the hot modulus of rupture (HMOR), hot modulus of elasticity (HMOE), as well as the wedge-splitting test (WST). The comparison of evolving microstructures was carried out employing scanning electron microscopy with microanalysis attachment (SEM/EDS) and X-ray diffraction (XRD). HMOR values of 12 MPa at 1300°C have been reached in MgO-Si02-C castables containing up to 7% carbon.

Jan 1, 2004

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By J. W. Choung, T. Fu, Z. A. Zhou

An on-line visualization technique and methodology was developed to investigate the role of fine sphalerite (< 10 um) aggregation in flotation. The images of particle aggregates under different operating conditions were recorded and analyzed. The effect of impeller design on particle aggregation was demonstrated. This difference was not mainly due to the energy input into the system, but due to the resultant hydrodynamic conditions created by the impeller and their effect on particle interactions. The recorded image showed that adding fine silica (- 5 um) did not interfere with fine sphalerite aggregation, thereby showing no effect on the sphalerite recovery. Effect of the enlarged aggregate size on increasing flotation recovery was confirmed. Although Malvern Mastersizer produced consistently lower estimates of aggregate size than those by the image analysis, both methods responded to the changes in operating conditions in the similar trend. It was shown from this study that on-line visualization technique is a powerful tool for studying fine particle aggregation and morphology in the context of diagnosis for the flotation separation.

Jan 1, 2004

By G. Issid, J. McGinty, C. Lee, Y. Pepin

For more than a decade, Hatch has used process and logistics models to assist Rio Tinto Fer et Titane (RTFT) with capacity planning, debottlenecking, and optimization to help ensure design capability, capital effectiveness, and operational efficiency of the integrated production chain. Process models are used to optimize the physics-based aspects of the system, such as mass and energy balances, flow rates, yields, and equipment specifications. Dynamic logistics models are used to optimize how the various plant areas work together to achieve the desired ends and deal with such things as plant scheduling and synchronization strategies, sizing of buffers between processes, defining the required number of process and material handling units, and designing a plant layout that minimizes plant interferences and inefficiencies. The combined use of process models and logistics models enables the overall plant to be optimized from both a productivity and quality point of view, with each plant area working in harmony with one another to achieve targeted capacities and efficiencies. This paper describes the many benefits derived from such modeling efforts over the past 15 years for each of the major plant areas at RTFT: Beneficiation Plant, Smelter Plant, Steel Plant, UGS Plant, and Powder Plant (RTMP).

Jan 1, 2011

By E. L. C. Martins, M. J. Nicol, D. Majuste, A. D. Souza

The effects of organic compounds on the current efficiency (CE), morphology, crystal structure and mechanical properties of the metal deposited during the electrowinning of zinc are described. A flotation collector and lubricating oil were selected based on observations made during the industrial production of zinc from silicate ores, in Brazil. The analysis by Fourier transform infrared spectroscopy of these compounds, which may be present in minor amounts in the electrolyte solution, indicated the presence of a polar amine group in the collector, while the lubricating oil is a non-polar compound. The average CE value obtained from organic-free industrial solution was 91.15 ± 0.26 %. The CE dropped to 54.35 ± 0.73 % in the presence of 100 mg·L-1 of collector in the solution, and a negative effect was also observed in the presence of similar amounts of oil (88.84 ± 0.61 %). The characterization of the deposits by scanning electron microscopy and X-ray diffraction revealed the formation of pores in deposits obtained from solutions containing the oil, while a different growth pattern (perpendicular zinc platelets) was identified when the flotation collector was added to the industrial solution. In the presence of these contaminants in the solution, guided-bend tests revealed that the deposits have a higher resistance to deformation, but lower ductility, properties that may affect the performance of the stripping stage. As a result of this work, simple control and optimization actions were applied in the industrial plant, which resulted in important improvements in the electrowinning process.

Jan 1, 2014

By F. Stober, D. Wanblad, J. Ndlovu, L. R. Nelson, L. P. S. de Villiers

The single six-in-line furnace of the Polokwane Smelter is the largest installed high-intensity furnace for platinum group metals (PGM) base metals sulphide smelting in the world. The furnace employs state-of-the art technology to deliver a planned throughput of 650 000 t/a dry concentrate at a design 68 MW power input. This furnace, at double the capacity of previously existing PGM furnaces, offers low unit operating and capital cost through the resulting economies of scale. Key features of the design include:

Jan 1, 2005

By W. G. Stevenson

With the author's background of extensive experience, this paper delineates the role of the prospector in modern-day exploration programs. The stages in the development of a prospect to a producing mineral district are outlined, and examples are given from the Ross River area of the Yukon Territory and the Peachland and Highland Valley areas of British Columbia.

Jan 1, 1970

In this study, flotation of fine galena, chalcopyrite and pyrite was performed after grinding with different extent of oxidation-reduction condition adjusted by grinding media. Sodium dithionite and iron ions were added in mill to simulate pulp potentials and iron oxidation species produced by grinding media, respectively. The types and quantities of the metal oxidation species on mineral surfaces were determined by EDTA extractions, while the surface electrical properties of minerals and interaction of different types of metal oxidation species were studied by zeta potential measurements. It was found that the nature and concentration of the absorbed metal oxidation species were dependent on oxidation atmosphere controlled by the iron amount of grinding media. These species interacted with each other and had an important role in determining flotation of fine galena and chalcopyrite as well as activation of fine pyrite by lead and copper.

Jan 1, 2006

By J. E. Dutrizac, R. J. C. MacDonald, J. B. O'Reilly

"Sometime around 3000 B.C., primitive metallurgists working in the mountainous regions of Asia Minor bordering on the Black Sea (Pontus) produced a soft, easily fused metal today known as lead. It appears certain that the first metal was made by reductive smelting of galena, but whether this recovery arose by the accidental inclusion of galena in the stones of a fire hearth or whether it occurred as a consequence of simple pyrometallurgical experiments on a series of interesting ""stones"" will likely never be known with certainty. The properties of galena, high metallic lustre, great density and facile cleavage, must have excited the ancients, and such ""stones"" would have been the object of primitive testing111 - Shortly after the discovery of lead, the ancients found that the controlled oxidation of this metal at elevated temperatures yielded smaller amounts of a more interesting material, silver. Again, it is uncertain if the production of silver by primitive cupellation techniques was the result of a fireside accident or the consequence of a deliberate experiment, but the important fact is that silver was produced shortly after the discovery of lead. The techniques for making lead and silver spread gradually throughout the entire civilized world, likely as a result of both technology diffusion and independent rediscovery. The physical properties of lead could not have been overly attractive to the ancients, but silver was a different matter altogether. The gleaming white lustre and relative immunity to oxidation quickly assigned silver to the precious materials category, a status it still enjoys. In early times, argentiferous galena was inevitably processed only for its silver values; lead was generally an unwanted byproduct and was frequently discarded as litharge (PbO) during the cupellation process. The silver was eagerly sought, however, and resulted in considerable mining activity culminating in the famous Athenian silver mines at Laurium at the southern end of the Athenian peninsula."

Jan 1, 1999

The use of roof bolting gave promise of substantial economic benefits to Continuous Miner operations at Michel Colliery. As the first step in the adoption of bolting, 142 anchorage tests, employing six types of anchor shells, were made in three mines. Significant differences were found in the anchorage capabilities of the various shells and the various roof rocks. Introduction S PORADIC attempts at roof bolting had been made at Michel Colliery over a period of ten years. Results were indifferent or inconclusive. A concerted effort was not made, because a compelling need for bolting did not exist. By 1962, however, the advent of Continuous Miners had brought a new significance to roof bolting and, at the same time, the increasing price and scarcity of mine timber made bolting materials more competitive in cost. A fresh appraisal of bolting, therefore, became justified and necessary. The potential benefits of roof bolting at Michel are several.

Jan 1, 1963

By Edward Thomas

Note. - Securing mine roof through consolidating thin or otherwise incompetent strata to increase overall thickness of the immediate roof beam is a new method of roof support and control which has aroused great interest amongst mining engineers and which is now being experimented with and thoroughly investigated by the United States Bureau of Mines. A paper on Roof Bolting, illustrated by photographs and motion-picture films, will be presented by Edward Thomas, of the U. S. Bureau of Mines, at the forthcoming Annual Meeting of the Mining Society of Nova Scotia. In the following pages, Mr. Thomas describes the methods used in roof bolting as illustrated by the photographs that accompanied his paper. The photographs are supplied through the courtesy of the United States Bureau of Mines, whose willing cooperation with miners and mining engineers in Canada is very well known and even more greatly appreciated. This method of publishing Mr. Thomas&apos;s paper is adopted because few, if any, Canadian mining engineers have actually seen installations of roof bolts and it is felt that the best possible presentation of such an interesting subject through the medium of the Bulletin will be attained by publication of the photograps over explanatory captions. - Ed.

Jan 1, 1950

By L. M. Dwarkin

Introduction Avital factor in the success of any coal mining operation is the method of roof support employed. A coal seam in? place has been described as the filling in a geological sandwich and the process of mining as the art of snatching the filling from the midst of the sandwich. The difficulty of this task can be appreciated -in the realization of the tremendous weight bearing on a coal seam due to overlying strata; a weight that can exert pressures of several thousand pounds per square inch. Over the years that mining has been carried on, methods have been evolved by arduous trial and error, making possible the successful extraction of billions of tons of coal. However, these time-proven methods are not enough. The constant demand for faster and cheaper production, the necessity of mining under increasingly difficult conditions, and the requirement for higher standards of safety, call for ever better and more efficient roof support. A recent and very promising development in answer to this need is that of Roof Bolting. Roof Support in General Before proceeding to the subject proper, a brief discussion of the older roof support methods is of value in illuminating the difficulties involved and the problems to be solved.

Jan 1, 1951

By L. M. Dwarkin, D. F. Coates

Crows Nest Industries Limited adopted roof bolting in 1963 to improve roof control and to extend continuous miner utilization in one mine. Bolting was held back because anchorage tests gave inconsistent results. The time lapse between mining and bolting was suspected as a cause, and so a test entry was driven and sections of it were bolted as part of the work cycle in addition to the normal timbering. This paper presents the results of the instrumentation of test entries and discusses the utilization of the data to improve mining procedure.

Jan 1, 1967

By Donald MacFadgen

Since 1950, a total of 164 miles of levels and rooms have been roof-bolted in the collieries of the Dominion Coal Company. Roof bolting is an efficient and economic method of sup-port where heavy timber sets or steel booms are necessary for temporary roof support, or where conventional methods of support interfere with the passage of mechanical mining equipment. This paper discusses present roof bolting practices and special bolting applications. THE practice of roof bolting in be collieries of the Dominion Coal Company dates from 1950, when preliminary studies and experiments were carried out in a mechanized room and pillar section of Dominion No. 20 Colliery. These studies were made in close liaison with members of the United States Bureau of Mines who were conducting similar studies. Following the successful application of roof bolting in No. 20 Colliery, this method of roof support was introduced into other collieries

Jan 1, 1963