Search Documents

By D. Harris, G. Ye, G. Oprea, J. Rigby, T. Troczynski

Sintering and ceramic bonding in refractory castables take place mainly in the binding system during the first heat-up and in service. Consequently the strength and the corrosion resistance of the hot face layer depend on the sintering ability of the complex mix of ceramic powders constituting the binding system. As a result, the use of nano- sized reactive powders in the binding system mixes would activate the sintering and enhance the ceramic matrix formation at temperatures below 1300°C. Our work presents the experimental data on sintering behavior of binding systems containing magnesium aluminate and alumina nano-powders in the temperature range of 800-1450°C. The results indicated that a ceramic matrix, similar to high temperature fired bricks, could be generated after firing at the relatively low temperatures available in the non-ferrous smelting furnaces.

Jan 1, 2004

By A. G. Roach

Introduction The plant described in this paper is located at Coniston, Ontario, the smelting centre of the former Mond Nickel Company. Coniston is situated some eight miles east of Sudbury on the main line of the Canadian Pacific railway and on the Toronto-Capreol branch of the Canadian National-railways. The plant is now under control of the International Nickel Company, as a result of the merger of the two companies in 1929. The smelter proper includes four 50-in. by 240-in. blast furnaces and five 13 ft. by 30 ft. converters, and has a capacity of about 65,000 tons of ore charge per month. As accessories to the smelter there are a mill, where some 10,000 tons per month of low-grade ores are concentrated, and the sintering plant, which is the subject of this paper. The present 6-unit sintering plant replaces a former 4-unit installation. Here, fine ores, concentrates, and flue-dust are sintered on Dwight-Lloyd machines, the sinter produced being charged into the blast furnaces. At the time of writing (1931), only the concentrator is operating at capacity, due to present world conditions.

Jan 1, 1932

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By John W. Korczak

The use of geological and grade block models has been standard practice in mine design for many years now, with a wide range of software available for creation and analysis. Although geotechnical parameters are of vital importance to mine planning there is very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology developed by the CSIRO (Commonwealth Scientific and Industrial Research Organization) in Australia for automated, safe and accurate 3D mapping of geological and geotechnical features. Datamine has integrated this capability into its product range so that Sirovision has become an integral part of the day-to-day mapping, mine geology and geological / geotechnical modeling in both open pit and underground mine environments. This is the first integrated underground application of Sirovision from Datamine collaboration with Xstrata Nickel at the Nickel Rim South Project. This paper discusses the role of Sirovision in collecting the raw data required for geological and geotechnical analysis and the interpretation in a quick, safe, auditable and reproducible manner.

May 1, 2009

By W. F. James

"The property of Siscoe Gold Mines, Limited, comprises about 1,600 acres, including Siscoe island and adjacent claims under water in Montigny lake, in Dubuisson and Vassan townships, Quebec.For many years the property was reached by way of Harricana river and its chain of lakes from Amos, Quebec, about 45 miles distant. In later years a highway has been built from Noranda east through Val d'Or, about 5 miles distant.Gold was discovered on one of the claims on the north shore of Montigny lake as early as 1911, but these gold discoveries have never been economically important. Several years later gold was discovered on Siscoe island and considerable surface work was carried out. Still later, iscoe Gold Mines, Limited, was formed and carried out further work, some of it through shallow shafts. In 1928, larger scale operations were undertaken and a 100-ton mill was constructed. In the years following, production· was on a larger scale with lower grade, until finally a milling rate of over 1,000 tons a day was attained. Approximately 1,500,000 tons were treated between the end of 1940 and mid-year 1945. At present the milling rate is down to about 200 tons a day and work is confined chiefly to some of the less important veins that have been recently developed.The following is a summary of production up to December 31st, 1946:"

Jan 1, 1954

By Rob Boom, Yasuyuki Tozaki, Frank M. Wheeler

Selection of a suitable site for a metallurgical plant is crucial for the success of the business case. For a brownfield project, with the decision to locate the project on a site with existing production facilities and activities, the selection of the site has been made. For a greenfield project, important economic and logistical considerations include proximity to primary and secondary resources and/or to the market, infrastructure, and access to energy and water. National and regional aspects, including the social license to operate, can be decisive in final site selection. Key to recruiting and retaining a labour force are proximity to urban areas, along with weather and health conditions at the site. Risk factors include site geotechnical parameters and topography, contamination, as well as probability and types of potential natural disasters.

Jan 1, 2015

By Lionel Roberge, Borge J. G. Fredriksson

"Late in 1981, a six-rope friction hoist was installed in the Number 2 shaft at Les Mines Seleine Inc. on the Madeleine Islands in Quebec. This paper deals with the reasoning behind the selection of hoisting equipment from the economical point of view, safety point of view, future needs point of view, etc.After establishing the basic parameters for the hoisting system, features of the most common types of hoists (i.e. single-drum hoist, double-drum hoist, Koepe hoist) are briefly laid out. The reasons for selecting a friction (Koepe) hoist are summarized. However, why go for a six-rope hoist rather than the (in North America) more common four-rope hoist? As the subject hoist is the first six-rope hoist in Canada, this question is studied in more detail, covering initial cost, maintenance cost, etc., as well as practical aspects, such as safety, physical dimensions, etc.In summary, experiences from other multi-rope hoist installations world-wide are presented.BackgroundIn 1980, Seleine Mines Inc. was established as a subsidiary of SOQUEM. The new mining company was to develop and operate a salt mine and associated harbour on the Madeleine Islands in the Gulf of St. Lawrence. The Madeleine Islands form part of the Province of Quebec. The mine has a planned annual output of 1.2 million metric tonnes of salt, with reserves in sight for over 20 years. Mining will be by room and pillar, with an underground primary crusher and treatment plant. From the underground treatment plant, the salt will be transferred via conveyors to a 5.5-metre-diameter circular shaft and hoisted to the surface. Surface transportation to the warehouse will again be via conveyor, and a conveyor will also transport the salt from the warehouse to the point of shiploading."

Jan 1, 1983

By J. C. Mitcheson

Mr. President, Mr. Mayor, Ladies & Gentlemen: IT GIVES ME great pleasure to have the opportunity, today, to speak on behalf of all the constituent. bodies of the Common-wealth Council of Mining and Metallurgical Institutions. For the past month we delegates have been right royally entertained across the length and breadth of Canada by Provincial Governments, City Councils, and other equally generous public organizations and private corporations. On this occasion, however, the President of The Canadian Institute of Mining and Metallurgy, our good friend Dr. H. J. Fraser, has been our host at the enjoyable reception preceding this Institute Luncheon, which luncheon was sponsored by our official host, The Canadian Institute of Mining and Metallurgy, one of our .constituent bodies.

Jan 1, 1957

By Shamil Shaikhutdinov

CO adsorption on gold particles deposited on well-ordered alumina and various iron oxide films has been studied with temperature programmed desorption (TPD) and infrared reflection adsorption spectroscopy (IRAS). Structural characterization has been performed with scanning tunneling microscopy. Data show that the CO adsorption exhibits a size effect in that small particles adsorb CO more strongly. The effect generally vanishes after annealing to 500 K. For annealed samples, CO TPD and IRAS spectra are nearly independent of the particle size and supports studied. The results indicate that the CO interaction with gold surfaces is essentially similar and involves low coordinated atoms.

Oct 1, 2003

By T. H. Patching, M. W. Mikhail

"Data from a standardized procedure for measuring methane desorption rates from samples of Western Canadian coals gave a good correlation (0.994) with the percentage of fines (-0.6 mm) found in the corresponding run-of-mine coal. The correlation was independent of the mining method and the top size of the samples. It is suggested that both methane desorption rate and the production of fine coal sizes are functions of the fissuration of the coal being mined.This relationship, in conjunction with established data of degradation by unit process equipment, may be useful in predicting the amount of fines that will be produced from new seams of coal and by planned new washeries. It also could be a valuable guide in modifying existing washery processes to minimize production of fines."

Jan 1, 1980

By M. Kataoka, Y. Obara

It is known that compressive strength and tensile strength of rocks vary significantly with specimen size. Rocks are composed of crystals and grains in a fabric that includes flaws such as microcracks, grain boundaries and pores. As the likelihood of including severer flaws becomes greater for a larger specimen, the strengths are small. On the other hand, the size effect in the fracture toughness of rocks has not been made clear until now because there are few studies focused on it. In this paper, Semi- Circular Bend (SCB) test was performed using Kimachi sandstone with various specimen sizes. A shape of the specimen is a semi-circular disc with an artificial notch. The specimens were prepared with various thickness t and radius r as the following two groups; t was changed from 10 to 37.5 mm with r = 37.5 mm in the specimen of group (a), and r was changed from 12.5 to 150 mm with t/r = 0.8 in the specimen of group (b). As a result, there was no significant change in the fracture toughness with different t. On the other hand, the fracture toughness increased with increasing r and converged on a certain constant value in a range larger than approximately 70 mm of r. Consequently it was clear that the size effect in the fracture toughness of the sandstone exists.

Jan 1, 2015

By B. Andreaus

In spite of tremendous efforts in research and development of polymer electrolyte fuel cells (PEFCs), essential properties of the actual catalyst material, supported Pt or Pt-alloy nanoparticles, are not yet well understood. Fundamental understanding of the catalyst structure and the prevailing kinetic mechanisms is, however, of utmost importance for further progress. In the present study, we investigate catalyst activity for CO oxidation from a theoretical point of view. Electrochemical CO oxidation serves as an important test reaction for the study of the fundamental properties of supported Pt nanoparticles. Recent experiments have revealed strong effects of catalyst particle size and supporting material on catalytic activity. It was found, that the activity towards CO oxidation decreases significantly when the particle diameter drops below 2.5 nm. We perform kinetic Monte Carlo simulations of CO oxidation on supported catalyst particles to elucidate this particle-size effect. The simulations are based on the active site concept, highlighting the role of active site formation and finite surface mobility of adsorbed electroactive species for catalyst activity. For comparison with experimental results, potential step experiments were simulated. The Monte Carlo simulations consistently reproduce effects of particle size and electrode potential found experimentally. In comparison with our simulations, analytical mean field models and nucleation and growth models exhibit inferior agreement with experimental data. In summary, our findings support an oxidation mechanism via active site formation. The reason for the slow reaction kinetics on catalyst particles with diameters below 2.5 nm is a rather low CO surface diffusivity. The rates of active site formation, diffusion and CO oxidation via recombination with adsorbed OH can be determined from the simulations.

Jan 1, 2005

By W. Pietsch

For a number of reasons, solids entering and leaving facilities for the treatment of minerals are becoming increasingly finer. Such materials pose problems throughout processing. Solids featuring small particle sizes tend to dusting, result in losses and segregation, exhibit various storage, transportation, and metering problems, and fine particulate effluents can not be easily captured, used and/or recycled. Sustainable mineral processing must minimize the exploitation of natural resources and avoid the need for disposal of wastes. The first requires the use of lower quality raw materials and upgrading, which typically results in the production of fine grained concentrates, and the latter encourages the recycling of wastes and byproducts or efforts to investigate them as sources for secondary raw materials or other beneficial applications. To overcome the difficulties associated with fine particulate solids, size enlargement by agglomeration is necessary. The resulting products have free flow characteristics, do no longer dust or segregate, and are sized and shaped as required for optimum processing. In addition, agglomerated materials may be engineered to feature desirable structure, composition, and a number of related, improved properties. Such engineering may be applied for the modification of fine run-of-mine and up-graded minerals as well as the production of secondary raw materials from by-products or wastes. By the interdisciplinary application of size enlargement by agglomeration waste-free processing of minerals becomes feasible.

Jan 1, 2004

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005

By J. E. Gill, A. R. Byers

"The property of Sladen Malartic Mines, Limited, is in the northern half of Fourniere township, Abitibi county, Quebec. The group is large, but the part so far found to be of economic interest is a strip 3,200 feet long between the Canadian Malartic property to the west and the East Malartic and National Malartic properties to the east ( Fig. 1).The original claims were staked in 1923 and 1924 by St. B. Sladen and H. S. Kennedy because gold was known to occur on claims nearby. In 1928, detailed mapping of the Malartic Gold Mines property (now Canadian Malartic) showed the presence of an east-west gold-bearing zone traceable almost to the Sladen boundary. During the winter of 1929, a hand-driven drill was used to secure short sections of core through casing pipe sunk to bed-rock. This proved the existence of the main Sladen ore zone, but it was not until the price of gold was increased, in 1934, that serious work was attempted.Underground work was started in 1935 and milling in January, 1938. To the end of 1945, 168,882 oz. of gold were recovered from 1,641,974 tons of ore, an average of 0.103 oz. a ton.GEOLOGYThe bed-rock underlying' the Sladen Malartic property consists mainly of Precambrian greywacke and volcanics that appear to form a conformable series with a general northwest strike and vertical to steep northerly dip. Except where disturbed locally by drag folds or faults, tops face north. Intrusive rocks that range in composition from diorite to granite cut the sediments and volcanics. The basic types, generally quartz diorite and diorite, form dykes or sills in the volcanic rocks. The more acidic types, mainly quartz syenite and related porphyries, intrude the volcanics and the sediments in the form of dykes, sills, and larger, stock-like bodies.The orebodies are parts of slightly shattered or brecciated zones, mainly in greywacke, but partly in syenite, diorite, and volcanics, that have been more or less replaced by fine-grained quartz, pyrite, and minor amounts of sphalerite, galena, sylvanite, petzite, and gold."

Jan 1, 1954

By A. Warczok

Smelting slags contain payable metals in a dissolved form and as mechanically entrained matte or metallic inclusions in the size range from 2 to 1000 µm. Slag cleaning requires reduction of magnetite and metal oxides and sedimentation of inclusions. Slag cleaning in an electric furnace is carried out in batch or semi-continuous mode. The strong trend for continuous slag cleaning generates the basic question about the optimal geometry of the electric furnace. Results of combined CFD, potential distribution and heat transfer modeling allowed for the determination of the fluid flow pattern and the temperature distribution in a classical, circular electric furnace as well as in a rectangular furnace. For the rectangular furnace, various length/width ratios and position of electrodes have been simulated. Analysis of key phenomena pointed out the advantages of the rectangular electric furnace over the circular furnace, particularly for continuous slag cleaning. Phenomena that have been analyzed were mass transfer, the rate of slag reduction, coalescence and settling of inclusions, all on the basis of the calculated slag flow pattern and the temperature distribution.

Jan 1, 2007

By J. Tuominen

Outokumpu Direct-to-Blister Flash Smelting is currently in operation in two smelters, a third one is under construction and a fourth one is in the design phase. The two smelters in operation are the Glogow 2 smelter of KGHM Polska Miedz S.A. in Poland and the Olympic Dam smelter of BHP Billiton in Australia. The Outokumpu Direct-to-Blister smelter of Konkola Copper Mines Plc. in Zambia is under construction and the new smelter of Glogow 1 is under design and waiting for final go-ahead decision. Additionally, the Garfield smelter of Kennecott Utah Copper Corp. makes blister copper out of matte in a Flash Converting furnace. A similar operation is under construction for Y anggu Xiangguang Copper Co. in China. The slag cleaning process, which is needed to clean the slag of the Direct-to-Blister Flash Smelting Furnace, has different requirements depending on the feed to the flash furnace. These differences are discussed in the paper. The differences between the processes and slag produced are discussed as well as the metallurgical requirements for slag cleaning. The Direct-to-Blister process, where the blister copper is produced directly from concentrate in one step, requires at least a partial treatment of the slag in an electric slag cleaning furnace. The existing impurities determine the specific requirements of the actual cleaning process. The different processes are discussed in the paper. The newest developments of Outokumpu Technology Oy for electric slag cleaning furnace design are presented as well as the characteristics which the furnace shape gives to the process.

Jan 1, 2007

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007