Search Documents

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By P. Toscano

The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C. Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed. Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses.

Jan 1, 2004

By P. Toscano, T. A. Utigard

"The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C.Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed.Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses."

Jan 1, 2004

By A. Warczokand

The cleaning of copper smelting slag requires magnetite and cuprous oxide reduction. The slag reduction with coke, injected coal powder or bunker oil is strongly endothermic and requires heat generation by fuel combustion or the use of electric energy. The reduction of fayalitic slag with calcium carbide is slightly exothermic and the formed calcium silicate modifies the slag. Thus, the additional energy is required only for covering furnace heat losses. Results of crucible scale tests showed the rate of slag reduction approximately five times higher in comparison of the slag reduction with coke under the same conditions. It seems that the effect of exothermic reaction and slag modification with CaO at the reaction interface results in very high rate of slag reduction. Industrial scale tests carried out in the Anglo-American Chagres Smelter demonstrated the possibilities of effective reduction and cleaning of the slags from a flash smelter and Peirce-Smith converters in a Teniente Slag Cleaning Furnace. The slag reduction was carried out without any reductant or stirring gas injection, simply by calcium carbide charging through a furnace mouth, and was very fast.

Jan 1, 2007

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By C. E. Cairnes

The Slocan mining camp in Kootenay district; British Columbia; has long been noted for the great number of its silver-bearing deposits; and for the success that has; in many instances; attended their development. The orebearing area lies east of Slocan lake and mainly within a radius of 6 to 8 miles of the mining town of Sandon. Within this limited area 135 or more properties have shipped ore in quantities of from 100 tons or less to more than 500; 000 tons; and with a total value in silver; lead; and zinc ranging from a few hundred dollars to well over $10; 000; 000. Of the three metals; silver has easily ranked first in value; with lead second and zinc third. Zinc production; however; made slow progress in the early years; and with . the exception of the Lucky Jim mine; and a few others where high-grade ore could be readily hand-sorted; was a detriment to the silver-lead ores until improved methods of separation enabled it to take an important place in the mineral production of the Slocan.

Jan 1, 1954

By Stephen B. Hearn

The SLon Vertical Ring and Pulsating High Gradient Magnetic Separator was developed to overcome multiple disadvantages associated with traditional horizontal type Wet High Intensity Magnetic Separators (WHIMS) which have been in service for many decades for recovering iron ore and other minerals. Proven successful, with hundreds of units now upgrading low-grade iron ores and maximizing recovery of fines throughout China, the technology is now being tested in the Western world. This paper will discuss the drawbacks of traditional WHIMS, explain the operation of the SLon, and illustrate its practical use in processing hematite ores.

May 1, 2007

By Z. M. Zavodni, C. D. Broadbent

"Major rock slides in open-pit mines are rare, but they can develop in spite of sophisticated slope engineering design practice. Experience has shown that, except under high seismic load conditions, the serious slope instability condition is almost always accompanied by the gradual development of one or more tension cracks behind the slope crest, allowing for time-displacement monitoring. Continuous surface displacement measurements with attendant prompt analyses are usually adequate for the prediction of slope behaviour.This paper describes efforts that have been made to quantify parameters associated with slide movement, and compares the displacement records of several large-scale open-pit porphyry copper mine slope failures. Two principal failure stages are recognized in the typical slope failure leading to total collapse: (a) REGRESSIVE STAGE, during which the failure will re-stabilize if some disturbance external to the rock and structure is removed; and (b) PROGRESSIVE STAGE. during which the failure will gradually displace at an accelerating rate to the point of total collapse unless active control measures are taken. Over-all displacement records in both failure stages are apparently of simple exponential form. with a definite break occurring at the onset-of-failure point.Certain common empirical relationships are suggested for the large-scale slope failures analyzed in this study. Based on plots of displacement rate vs time prior to collapse, a semi quantitative empirical relationship is presented for failure collapse prediction. The comparison of historical slide displacement records furnishes the operating engineer with practical guidelines to estimate the characteristics of future large-scale slope failures."

Jan 1, 1980

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By Neal Harries

Ground movement is normal in open cut mining operations, mainly caused by excavation response and blasting. Movement of the ground can be acceptable provided it is not unexpected and catastrophic. However, in steep mine walls and the very large open pits being developed today the consequence of slope collapse can be catastrophic. Such risks can be minimized at the planning stage by reducing slope angles, but this carries a very high cost. Also, instabilities which develop whilst mining can lead to ore reserves being quarantined, which represent a high cost to the mining operation. In spite of such safety measures, unexpected failures have occurred in the past. These issues motivated the development and production of the slope stability radar (SSR). There are currently over 80 GroundProbe SSR systems deployed in metalliferous and coal mines in 17 countries. The unexpected failure of rock walls at mining sites is a major cause of death and serious injury. Slope failure is also one of the major causes of economic and production losses. An unexpected wall failure can bury critical equipment. It also disrupts the mine plan. It is common to cease mining for several days or weeks following a wall collapse due to uncertainty over stability. Direct economic losses in remediation alone can easily exceed $1,000,000 per incident. The economic costs of injury or fatality are much higher including closure of mines during the incident investigation process. Massive wall failure can result in direct and indirect costs measured in millions of dollars. This paper will present some recent case studies of the SSR operation in open cut mines in North America, including Thompson Creek Mining Company (Idaho), Smoky Canyon Mine (Idaho), and a general case study on extreme cold weather use of the SSR.

May 1, 2009

By J. Robison, H. Pieterse, C. C. Smith, M. Luque, S. Chipman

Phase change during pressure let down releases significant amounts of energy that must be controlled to avoid undo wear and tear on equipment. Hydrometallurgical slurries require flow control equipment (valves and tanks) made of expensive materials to withstand the abrasive, and often corrosive nature of the slurry. Presented is a model of the nozzle of a let-down choke which is designed to control the flow pattern that exits the choke (valve) as it enters the receiving tank. This model can be used to design chokes which allow for the dissipation of the energy released during pressure let down by spreading the stream over a significant portion of the slurry pool in the receiving tank to minimize wear on equipment near the nozzle exit and the bottom of the slurry tank. An example uses the model to choose the nozzle expansion (area) ratio to select the outlet slurry velocity and slurry expansion angle.

Jan 1, 2004

By Ron H. Derammelaere

Coal Slurry Test Pipeline and First Recorded Commercial Pipeline Wallace Andrews founder of New York Steam Company awarded patent for ?Method of Transportation? that involved pumping finely divided coal in slurry form built test facility at Madison Avenue and East 58th Street in New York City died in 1899 in a fire and coal pipeline work was not continued First recorded commercial coal slurry pipeline designed by Gilbert Bell in 1914 to move coal from barges on the Thames River in London to a powerhouse in 8? tubes (660 yards long)

May 1, 2013