Search Documents

By D. Assmus, S. Daly

"Poor fragmentation, high toe areas, excessive shovel wear and tear and frequent re-drilling and blasting of certain tough waste rock zones in the Lomex pit in the early 1980snecessitateda better understanding of these zones.A combination of geotechnical mapping, penetration rate data, toe elevation contouring and observations on shovel and drill performance were used to determine the character and extent of these zones. This complementary information was brought together by the geotechnical mapper and the explosives supervisor.Distinct zones with particular geological characteristics were determined. A classification system with three types of blast and dig-ability was developed for the Lomex pit and later applied to the Valley pit, with considerable success. The three blast zone types are called ""poor"", ""f air"", and ""good"". This system will be described in detail.The explosives supervisor adjusted the blasting parameters to each zone, in particular, pattern spacing and burden. The resulting powder factors showed considerable variation between the poor, fair and good zones within each pit as well as between the two pits. Pattern geometry and length of collar were also adjusted to improve fragmentation. Cost savings resulted from less re-drilling and less wear and tear on drills and shovels in the poor zones and more efficient use of explosives in all the zones. An annual estimated cost savings of well in excess of $1,000,000 is realized at Highland Valley Copper. A by-product of the mapping was the determination of unstable structures and water flowing zones. Blasting was then adapted to this information for enhanced slope stability."

Jan 1, 1992

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre's (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

By P. Favreau

This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.

Feb 1, 1993

By R. H. Brooks

Blasthole stoping methods were introduced at Birchtree Mine as an alternative to the original cut-and-fill and shrinkage stoping methods. The object was to take advantage of the ore structure and conditions, and achieve increased productivity. This paper outlines the design, operation and economics of three areas which utilized blasthole stoping. The 108areafrom 2300 level to 1500level was converted from cut-and-fill to sublevel blasthole stoping based on a block mining-and-filling sequence. The second area, the crown pillar of 110 mechanized cut-and-fill stope below 500 level, was recovered using horizontal rings drilled from raises within the ore zone. The third area, the 83 orebody from 1300 level to 1100 level, used the vertical crater retreat (VCR) method with large-diameter blastholes. Blasthole stoping has increased productivity and improved operating conditions.

Jan 1, 1979

By Y. Lizotte

"This paper examines the application of blasthole sloping to narrow vein mining in Canada, for ore deposits where widths are less than two metres. While the technique has now been utilized for more than ten years, it remains in the experimental stage and on-site testing is necessary for its adoption at new mining operations or in differ¬ent geological settings. It is intrinsically a safer method than other narrow vein methods in current use.The investigation describes the main operating parameters for mines recently surveyed. The criteria for method applicability are defined and the problems encountered are studied. It is concluded that blasthole sloping for narrow vein mining is a viable modern method which promises to gain popularity and that emerging fragmentation technology and blasting research can be used to further increase applicability of the stoping method."

Jan 1, 1991

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By Chris G. Dobson

Introduction The Britannia mine is at Britannia Beach, on Howe sound, approximately thirty miles from Vancouver. The first claims were staked in 1898, and a local company was formed at that time to develop them. In 1904, Mr. Grant B. Schley became actively interested in the property and in the following year the Britannia Mining and Smelting Company, Limited, was incorporated to operate it. This Company was taken over a few years later by the Howe Sound Company, Limited. The mine comprises five more or less separate ore-bodies, which have produced approximately 20,000,000 tons of ore to date. The East Bluff ore-body, with which the present paper deals, is well suited to large-scale mining by means of carefully placed powder blasts. It covers approximately an acre and lies in the slate footwall, in a bay produced by a fault. The hanging-wall side, on the west, forms the face of the Bluff glory-hole, which extends to the 1,200 level. A portion of this ore was available for breaking into this old glory-hole, below which four bulldoze chambers could quickly be built. Mining of this block is complicated by a very soft footwall, which 'runs' badly when broken. In stoping, care is taken to guard against the hazard of dilution by deliberately leaving a small portion of ore on the footwall. Some of this will undoubtedly be lost, but it is hoped to recover a fair amount of it after the major drawing is completed. The deposit occurs in a greenstone which has been highly silicified following brecciation. The chief minerals are chalcopyrite, sphalerite, and pyrite. Concentrates of copper, zinc, and pyrite are made at the mill. The average grade of ore runs 0.7 per cent copper, 1.5 per cent zinc, and 0.03 oz. gold per ton. The rock, which is practically a chert, is extremely hard, but shatters well. Both in stoping and drifting, holes must be closely spaced and powder used generously. Development When development work started in the East Bluff, there were no raises and only one drift on each level in this section of the mine. After blocking out the ore by thorough diamond drilling, a production of two thousand tons per day was set as a goal. To obtain this tonnage from so small an area required a great deal of carefully planned and well timed development work.

Jan 1, 1935

By L. H. Bergmann

THE blasting practices described are fairly representative of those employed in the coal mines of Eastern Canada. As such, they may be of interest to Western Canadian coal mine operators. The treatment of the subject is general, no attempt being made to discuss blasting operations at any particular coal mine in detail. All the mines dealt with are mining bituminous coal and are classified under the Coal Mines Regulation Act of the Province of Nova Scotia as 'closed light' mines. As such, they are required to use only 'permitted' explosives and to apply them in a 'permitted' manner, except where authority is given by the Mines Department to do otherwise.

Jan 1, 1945

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By Wm. L. Giachino

"Over the last 10 years, C-1-L has played a significant role in the major advances that have taken place in blasting technology, among them the following: development and introduction of capsensitive slurries; development of bulk slurry systems both for underground and open-pit operations; development of the TOE-DET and ANODET systems of delay blasting;introduction of the NONEL system of initiation;development of the Vertical Crater Retreat (VCR) system of mining.This paper identifies areasin which we foresee further developments in blasting technology over the next 10 years and outlines how and to what extent C-1-L will become involved."

Jan 1, 1980

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By G. Rong, W. Du

Stability of some potential unstable blocks in the left bank slope of Baihetan hydropower station is evaluated in this paper using the three-dimensional (3D) limit equilibrium method. The Baihetan hydropower station is in the downstream of Jinshajiang River, China. The geological condition in the river valley is complex, and many large discontinuities are detected in the slope of the two banks. As a result, much attention should be paid to the stability of the slope in the feasibility study stage. Because the left bank slope is an oblique consequent one, we mainly focus on the slope stability analysis in the left bank. Comprehensive geological exploration is conducted in the studied area and the detected discontinuities are well researched. By building a 3D geological model of the left bank slope, three potential unstable blocks which are close to the dam site are detected. An irregular wedge analysis method is then used to calculate safety factors of the three blocks under three conditions, which are natural condition, rainfall condition, and seismic condition, respectively. It is found that the safety factors of the block 1# and the block 2# are quite low when compared to the suggested values. Extra care must be exercised when excavating the slope near the block 1# and the block 2#. A preliminary reinforcement is also suggested.

Jan 1, 2015

By S. Fuentes, J. Cáceres

"During the past fifteen years, mines utilizing the block caving method have improved performance and systematically reduced total mining costs.This paper describes improvements in mine design, mine planning, and mine management, including methods enabling the Chilean and international mining industry to ensure cost savings and productivity growth while using the block caving method. These improvements have encouraged the re-evaluation of underground operations at operating and closed open pits, and challenge surface mining applications as the only low-cost mining method. This paper describes a strategy to estimate the optimum open pit to underground transition time during the life of a mine. IntroductionDuring the last fifteen years, block caving mines have experienced huge changes in designs, planning and administration. These changes have permitted operators to drastically reduce costs, improve equipment productivity, and improve overall business performance. As a consequence of this situation, the block/panel caving mining system is challenging actual open pit operations to maximize the net present value (NPV)."

Jan 1, 2004

By A. Belleau, F. Lavoie

"Quebec Iron Ore Limited (QIO), a subsidiary of Champion Iron Limited (Champion), secured assets in early 2016 from the previous Bloom Lake operations in the heart of the Labrador Trough region of Northern Quebec, Canada. A plan was developed to bring the Bloom Lake facility back in operation once the iron ore market conditions improved. The project restart involved several aggressive moves to change operational effectiveness, one of which was the utilization of the existing Phase 1 Plant with an upgraded process flowsheet and equipment. The production target was 7.4 million tonnes per annum of 66% iron ore concentrate with an approximate 10% increase in iron ore recovery. The Phase 1 upgraded flowsheet was initially based on review of historical Phase 1 data and pilot testing data undertaken during the original Phase 1 operation and was finalized once additional metallurgical test work and process modeling was carried out by Mineral Technologies in late 2016. The final upgraded flowsheet is comprised of rougher spirals, rougher middling scavenging spirals, and an up-current classifier (UCC) with overflow scavenging spiral stage. A portion of the gravity circuit tailings treated by a series of wet high intensity magnetic separators (WHIMS) to boost overall iron recovery. This paper will describe the efforts taken to test and design the Bloom Lake Phase 1 upgraded flowsheet and report on the plant performance since commissioning in first quarter of 2018.SITE HISTORY The Bloom Lake iron mine property is located approximately 13 km north of Fermont, Quebec, and 10 km north of the Mont Wright iron ore mining complex, property of ArcelorMittal Mines Canada. The Bloom Lake mine facilities include a 32 km railway to efficiently transport the high-quality iron concentrate to a loading port located in Sept-Iles, Quebec. The Bloom Lake property was first explored in 1951 and went through multiple minor exploration campaigns by different companies up until 1998. A major exploration program was conducted by Quebec Cartier Mining (QCM) in 1998. This program included line cutting, surveying, diamond drilling, geological mapping, mini-bulk sampling, bench-scale preliminary metallurgical test work and preparation of a “mineral resource” estimate."

Jan 1, 2019

By A. Fischersworring-Bunk

The new inline six spark-ignition engine is the realization of BMW's concept of efficient dynamics at high technological level to achieve the attributes of low weight and high efficiency, The paper presents different aspects of the development and manufacturing of BMW's inline six-cylinder engine magnesium-aluminium composite crankcase, Reference will be made on the AJ magnesium alloy optimization approach to balance between mechanical properties and the high pressure die cast ability requirements, Next to this aspect some mechanical design issues will be covered, with CAE methods playing an instrumental role in the early project stage for the assessment of the compound concept, Due to the compound design chosen, the interface posed challenges to both design and productions, A set of novel techniques has been used to cope with these tasks.

Jan 1, 2006