Search Documents

By Wm. L. Giachino

"Over the last 10 years, C-1-L has played a significant role in the major advances that have taken place in blasting technology, among them the following: development and introduction of capsensitive slurries; development of bulk slurry systems both for underground and open-pit operations; development of the TOE-DET and ANODET systems of delay blasting;introduction of the NONEL system of initiation;development of the Vertical Crater Retreat (VCR) system of mining.This paper identifies areasin which we foresee further developments in blasting technology over the next 10 years and outlines how and to what extent C-1-L will become involved."

Jan 1, 1980

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By G. Rong, W. Du

Stability of some potential unstable blocks in the left bank slope of Baihetan hydropower station is evaluated in this paper using the three-dimensional (3D) limit equilibrium method. The Baihetan hydropower station is in the downstream of Jinshajiang River, China. The geological condition in the river valley is complex, and many large discontinuities are detected in the slope of the two banks. As a result, much attention should be paid to the stability of the slope in the feasibility study stage. Because the left bank slope is an oblique consequent one, we mainly focus on the slope stability analysis in the left bank. Comprehensive geological exploration is conducted in the studied area and the detected discontinuities are well researched. By building a 3D geological model of the left bank slope, three potential unstable blocks which are close to the dam site are detected. An irregular wedge analysis method is then used to calculate safety factors of the three blocks under three conditions, which are natural condition, rainfall condition, and seismic condition, respectively. It is found that the safety factors of the block 1# and the block 2# are quite low when compared to the suggested values. Extra care must be exercised when excavating the slope near the block 1# and the block 2#. A preliminary reinforcement is also suggested.

Jan 1, 2015

By S. Fuentes, J. Cáceres

"During the past fifteen years, mines utilizing the block caving method have improved performance and systematically reduced total mining costs.This paper describes improvements in mine design, mine planning, and mine management, including methods enabling the Chilean and international mining industry to ensure cost savings and productivity growth while using the block caving method. These improvements have encouraged the re-evaluation of underground operations at operating and closed open pits, and challenge surface mining applications as the only low-cost mining method. This paper describes a strategy to estimate the optimum open pit to underground transition time during the life of a mine. IntroductionDuring the last fifteen years, block caving mines have experienced huge changes in designs, planning and administration. These changes have permitted operators to drastically reduce costs, improve equipment productivity, and improve overall business performance. As a consequence of this situation, the block/panel caving mining system is challenging actual open pit operations to maximize the net present value (NPV)."

Jan 1, 2004

By A. Belleau, F. Lavoie

"Quebec Iron Ore Limited (QIO), a subsidiary of Champion Iron Limited (Champion), secured assets in early 2016 from the previous Bloom Lake operations in the heart of the Labrador Trough region of Northern Quebec, Canada. A plan was developed to bring the Bloom Lake facility back in operation once the iron ore market conditions improved. The project restart involved several aggressive moves to change operational effectiveness, one of which was the utilization of the existing Phase 1 Plant with an upgraded process flowsheet and equipment. The production target was 7.4 million tonnes per annum of 66% iron ore concentrate with an approximate 10% increase in iron ore recovery. The Phase 1 upgraded flowsheet was initially based on review of historical Phase 1 data and pilot testing data undertaken during the original Phase 1 operation and was finalized once additional metallurgical test work and process modeling was carried out by Mineral Technologies in late 2016. The final upgraded flowsheet is comprised of rougher spirals, rougher middling scavenging spirals, and an up-current classifier (UCC) with overflow scavenging spiral stage. A portion of the gravity circuit tailings treated by a series of wet high intensity magnetic separators (WHIMS) to boost overall iron recovery. This paper will describe the efforts taken to test and design the Bloom Lake Phase 1 upgraded flowsheet and report on the plant performance since commissioning in first quarter of 2018.SITE HISTORY The Bloom Lake iron mine property is located approximately 13 km north of Fermont, Quebec, and 10 km north of the Mont Wright iron ore mining complex, property of ArcelorMittal Mines Canada. The Bloom Lake mine facilities include a 32 km railway to efficiently transport the high-quality iron concentrate to a loading port located in Sept-Iles, Quebec. The Bloom Lake property was first explored in 1951 and went through multiple minor exploration campaigns by different companies up until 1998. A major exploration program was conducted by Quebec Cartier Mining (QCM) in 1998. This program included line cutting, surveying, diamond drilling, geological mapping, mini-bulk sampling, bench-scale preliminary metallurgical test work and preparation of a “mineral resource” estimate."

Jan 1, 2019

By DALE MacGREGOR, VERA TUREK

The Blue Mountain nepheline syenite deposit has been the subject of several detailed studies. It has been variously referred to as an intrusive stock, a metasomatic deposit, an intrusive sill and a metamorphic-metasomatic body. The body is divided into six mineralogical zones, the first five being based on the characterizing accessory mineral; muscovite, muscovitemagnetite, biotite-muscovite, biotite, hornblende and pink syenite. Mining currently takes place only in the biotite zone. Foliation is particularly prominent in the central (hornblende) zone and near the margins of the nepheline syenite. Majic bodies within the nepheline syenite may represent basic rocks that have been less altered by metasomatism, metamorphosed basic dykes or sloped blocks of metasediments. The most prominent structural features are the northeast-trending folds that have been modified by later north west-trending folds.

Jan 1, 1984

By A. Fischersworring-Bunk

The new inline six spark-ignition engine is the realization of BMW's concept of efficient dynamics at high technological level to achieve the attributes of low weight and high efficiency, The paper presents different aspects of the development and manufacturing of BMW's inline six-cylinder engine magnesium-aluminium composite crankcase, Reference will be made on the AJ magnesium alloy optimization approach to balance between mechanical properties and the high pressure die cast ability requirements, Next to this aspect some mechanical design issues will be covered, with CAE methods playing an instrumental role in the early project stage for the assessment of the compound concept, Due to the compound design chosen, the interface posed challenges to both design and productions, A set of novel techniques has been used to cope with these tasks.

Jan 1, 2006

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By J. L. Bowlby

TWO years ago, at the annual meeting of this Society, the writer presented a paper dealing with various aspects of the water problems existing in the Cape Breton coal-mining area. Much of that paper was of a theoretical nature, in that an attempt was made to get at the fundamental principles underlying the problems, in order to establish a sort of background against which future results could be laid. Up to that time, only Central power plant in Glace Bay had been under observation, and, since the work had been in progress only a year, it was recognized that there were strong possibilities that certain variations in procedure might have to be introduced as w; became better acquainted with our problem. We were by no means certain that we had covered all the facts of the case. The present paper will therefore be of the nature of a progress report, rather than a formal contribution to the Society. Subjects of a theoretical or academic nature will be avoided as far as possible, attention being confined chiefly to the results obtained during the past two years. In looking over the work with low-pressure boilers, there are certain general conclusions that can apparently be safely drawn. Wherever possible, proper operating conditions will be expressed in terms of appropriate units. Absence of corrosion in boilers where the alkalinity has been maintained within the pH range 11.0 to 11.4 forces one to the conclusion that these are safe working limits. Previous experience had shown that corrosion would occur if the alkalinity were much reduced. Higher alkalinities are un-necessary, more expensive, and are said to introduce the possibility of pitting. We made no attempt to obtain quantitative data in respect to pitting. It is said to occur at pH 12.0. Consequently, conditions of alkalinity were main-tained well below this figure. In the above paragraph, the pH range 11.0 to 11.4 applies to boiler waters which have received the lime and soda treatment. The general practice, when this treatment is employed, is to use 1.0 lb. lime to 7.0 lb. washing soda. At Central power plant, soda-ash is at present substituted for washing soda, the equivalent proportions being kept the same. But not all the plants are on the lime and soda treatment. At Waterford Lake, a 1: 1 mixture of soda-ash and trisodium phosphate is satisfactorily employed, and in Sydney Mines and at No. 3 power plant in Sydney, good results are being obtained at a somewhat greater cost with a commercial phosphate treatment.

Jan 1, 1936

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By Mark Sherman

One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client?s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques. Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt?s Grindpower and OMC?s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC?s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics. The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing. The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor?s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved.

Jan 1, 2012

By Mark Sherman

"One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client’s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques.Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt’s Grindpower and OMC’s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC’s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics.The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing.The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor’s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved."

Jan 1, 2012

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By Noel Billette, Jean-Luc Chouinard

"An analysis of the number of industrial injuries shows that the mining sector is particularly affected, since mining is one of the most dangerous industrial activities in Canada. This has led to numerous inquiries, and supports the need for an in-depth study aiming at the identification of factors responsible for these accidents. One possible factor often pointed at is the small crews incentives and this paper presents a scientific approach applied to check a potential link between bonus and accidents at two mining companies located in northwestern Quebec.The data required to do so were the accidents, the salaries and the number of hours worked at each mining site by the hourly paid personnel for the period from June 1979 to January 1982. The analysis of the results derived from the initial information shows different behaviours of the frequency rate vs the bonus rate at these mines. The number of days lost per accident is independent of the bonus rate at both mine sites, as shown by Khisquare tests on contingency tables.IntroductionA wide variety of opinions has been pinpointed by a survey of the literature related to individual or small crew incentives and industrial accidents in sectors of activity where it applies. In addition, various formulae of mining contracts take place in the industry on one part, and statistics from this sector indicate a high accident frequency rate on the other part. These fact s have lead to this scientific investigation which does isolate the direct impact of the bonus on workers' accidents. This study was undertaken with the full support of the Quebec Metal Mining Association.The conclusions of this preliminary phase of the researchproject are presented for two mining complexes in northwestern Quebec. The procedure is somewhat similar to the approach of the Belmoral Commission, with the underlying assumption that bonus has a direct impact on accidents."

Jan 1, 1986

By M. G. Stamatakis, C. Zagouroglou, C. Helvaci, J. Kanaris

"Abstract -Borate minerals, such as colemanite, ulexite and borax, have been reported in Tertiary continental basins of West Anatolia, Turkey, and Samos Island, Greece.Tuffaceous rocks interbedded with the borates are rich in authigenic silicate minerals such as zeolites, potassium feldspar and opal-CT, all of which have a genetic association with the borates. Chemical analyses of the tuffaceous rocks show variation in major elements due to the varying percentage of carbonaceous, detrital, and volcanic derived material.The volcanic activity in the vicinity of each particular lacustrine basin created ion-rich fluids from which a series of borates were precipitated under arid climate. Additionally, the saline-alkaline character of these fluids was responsible for the diagenesis of the silicic glass of the tuffaceous rocks, altering them to silicates and silica polymorphs."

Jan 1, 1993

By C. J. Mwenifumbo

Preservation of groundwater quality is a major environmental concern. The disposal of hazardous material from urban waste dumps, milling wastes in tailings ponds, and industrial wastes in injection wells may contaminate potential sources of potable groundwater. The containment or migration of contaminants in the subsurface depends on bedrock characteristics and type of overlying sediments. Fractured bedrock and permeable sediments that may provide pathways for the transport of potentially harmful contaminants should be avoided when selecting a disposal site. The role of borehole geophysics in hazardous waste-site investigations is reviewed in three categories: (I) site selection; (2) determination of the extent of contamination at existing sites; and (3) long-term monitoring of migration of contaminants. In the first category, borehole geophysical techniques developed for lithology and fracture identification, and for porosity determination, provide some of the necessary information for understanding the subsurface hydrogeology. Lithological information can be obtained from gamma-ray, electrical resistivity, induction, magnetic susceptibility, and sometimes induced polarization logs; fracture detection and characterization can be accomplished with the use of caliper, density, resistivity, temperature, and acoustic televiewer logs. Estimates of porosity are derived primarily from neutron-neutron, resistivity, density, and soniclogs. Borehole geophysical techniques used in water quality determinations include self-potential, fluid resistivity, Eh (redox potentials) and pH measurements, and these can be used to map the extent of contamination at an existing waste site. Cross borehole and borehole-to-surface electrical methods can also be used in this application. Long-term monitoring of contaminant migration in boreholes can be accomplished with techniques that respond to changes in electrical conductivity, temperature and fluid chemistry caused by the presence of contaminants.

Jan 1, 1993

By J. G. Kelly, C. P. Brown

"In June 1983 a new borehole hoisting system was commissioned at Sherritt Gordon's Fox Mine. Twelve hundred tons-per-day of ore from the 2600 and 2800 levels are being hoisted to the 2000 level through an 8-jt diameter bored winze. This new method replaces the diesel truck haulage system which had been in operation at the mine since 1975.A study was initiated in 1980to determine the most effective method of achieving the required production. The study examined several hoisting alternatives including: expanding the existing trucking system; converting to electrically -powered truck haulage; and deepening the skip compartments of the existing main shaft. The alternative selected as the hoisting method most suited to the requirements was borehole hoisting.Development of the new system commenced in April 1982. Underground excavations included 700 feet of 8-ft diameter borehole, a hoistroom and headframe, storage bins, and a grizzly and rockbreaker station. Equipment installations included: a 5-ft diameter double-drum Nordberg hoist; a counterweighted Kimberley-type skip; two rockbreakers; and the steel sets in the winze. These installations were completed in June 1983. Some problems were encountered after the initial commissioning but these were solved, and since August 1983, the system has proven that the designed capacity is achievable within expected costs."

Jan 1, 1985

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By M. Keen

The backfill system at Cleveland Potash?s Boulby Mine places waste filter cake underground in the form of a high concentration slurry in worked out areas of the mine reducing the mine?s environmental impact. The backfill system delivers slurry approximately 1100 m down the mine and up to 11 000 m horizontally underground. The Boulby backfill system is unique in that the placed backfill waste is not used for the usual purposes such as support, pillar extraction or reducing ventilation requirements. It was specifically implemented for environmental reasons. This influenced the design and resulted in some unique features of the system. A previous paper (Wilkins et al., 2004) described the design and commissioning of the backfill system. This paper describes the operational experience with the backfill system and backfill placement since commissioning in May 2003 and looks at lessons that can be applied in other backfill designs.

May 1, 2007