Search Documents

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By W. B. Paton

Introduction For several reasons the accident history of Flin Flon has been quite unlike that of any other mine in northern Canada, and very much unlike that of the average American metal mine. Towards the end of 1928, the mining project that is now Flin Flon, and that is now in the very: forefront of Canada's big producers was launched; but, metaphorically, it was launched in a tempest of mining troubles. Each branch of the mammoth enterprise was beset with extraordinary difficulties, and the Safety Department had its relative share. Difficulties in Accident Prevention The unusually rugged contour of the plant site made roads, and even moderately safe pathways, out of the immediate question. The project established an industrial outlet for depression-stricken areas which hitherto had been essentially agricultural; but through that outlet poured labour whose working atmosphere had been the bald prairie, labour that knew nothing of safety consciousness, labour that had to be moulded to industrialism, labour in the raw. A considerable length of the ore-body lay under the eastern section of Flin Flon lake. Open-pit methods were adopted to work the upper limits of the ore-body, and consequently the eastern section of the lake had to be dammed and pumped dry. The subsequent difficulties and hazards created by silt deposit cannot be fully visualized. And, finally, there was a geographical hindrance: the ore-body was partly in the Province of Manitoba and partly in the Province of Saskatchewan. The workmen's compensation problem became intricate. Insofar as accident prevention is concerned, Flin Flon's young industrial life may be conveniently divided into three distinct periods, namely: (a) Construction (Nov. 1928-June 1930) (b) Tuning up, and production till the strike (June 1930-June 1934) (c) Production from the strike till the present time At the peak of construction, due to the usual labour fluctuations of big jobs, there was a weekly turnover of about a hundred men. A very large percentage were Central Europeans, most of whom could neither read nor write English. Consequently, an organized safety programme was out of the question.

Jan 1, 1935

By J. R. Bradfield

THOSE familiar with the development of the Horne mine can readily appreciate that more and more accommodation bas been required for underground labour as the mine has grown. A permanent fire-proof change house, 30ft. by 75 ft., was built in 1927 to accommodate 194 men. This was extended ro 30 ft. by 92 ft. in 1928 to accommodate 296 men, and to 30ft. by 110 ft. in 1930 to accommodate 398 men. By 1933 this building was again overcrowded and tentative plans for a new change house were drawn up. However, it was realized that future operations would be centred around No. 4 shaft and a proposed new shaft, and the decision as to the location of the new change house had to be deferred until the area which seemed most suitable for the new shaft had been thoroughly explored underground. In the spring of 1934, the basic idea was accepted of drying the wet clothes in open mesh compartments or baskets located between rows of standard steel street-clothes lockers and built so that the covers or lids would serve as seats or benches.

Jan 1, 1935

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By Alan A. Barton

Introduction The Little Long Lac mine is situated in the Thunder Bay mining district, township of Errington, Ontario. The mine is located on the south side of the most westerly bay of Little Long Lac. The property consists of 36 claims, which comprise some 1,400 acres. This group of claims was staked in August, 1932, by Tony Oklend and Tom Johnson, and, after surface sampling, was optioned by the present controlling interests, who diamond-drilled it during the winter of 1932-33. In early spring, a small steam-driven plant was installed, and shaft sinking commenced on June 1st, 1933. During the summer, all supplies are transported to the mine from Hardrock station, at mileage 18 on the Canadian National Railway line from Longlac to Port Arthur. At Hardrock, which is seven miles from the mine, the railway skirts a bay of Little Long Lac, and supplies are loaded directly from railway cars to scows. Two scows are used, of 30-and 45-ton capacity, respectively. A 36-ft. pointer, powered by a 35 h.p. engine, is used as a tug. A good winter-road has been cut out from Geraldton to the mine, for winter transportation. Geraldton is about two miles north of the mine, and is also located on the Canadian National railway. A hard-surface road is now being constructed for summer as well as winter use. Geology The Little Long Lac gold area covers the northern limits of a large synclinal structure, the contact of the Keewatin flows and sediments, striking about twenty degrees north of west, with the dip of the sediments varying from eighty degrees north to seventy degrees south, the average being around eighty degrees south. The vein worked by Little Long Lac Gold Mines occurs in massive sedimentary rock of about the composition of arkosic or quartzitic greywacke, and consists of a shear-zone up to fifteen feet in width, striking N.75°E. and dipping steeply to the south, which has been filled by numerous narrow, parallel quartz veins and. veinlets. These are well mineralized. with arsenopyrite, pyrite, and some chalcopyrite and stibnite, and carry considerable quantities of visible gold. They show more than one age of quartz deposition, the quartz being fractured and re-cemented. The arkosic rocks separating the veins and veinlets are also slightly mineralized with pyrite. Work to date has indicated the probability that the vein-shear is controlled by local drag-folding.

Jan 1, 1935

By R. E. Phelan

Introduction The Flin Flon deposit was discovered by Tom Creighton, an experienced prospector and trapper, who in 1914 made his headquarters at The Pas, Manitoba, and still lives there. The discovery was made in the fall of 1914, and Creighton and his associates spent the next summer in investigating the find. In August of 1915 the first claims were located. The property was optioned to Hayden Stone & Company, and in the spring of 1916 they started a diamond-drill campaign. Hayden Stone spent $50,000 on the property and, among other things, completed over 7,500 feet of diamond drilling. The ore not being as high grade as expected, and also being complex in character, Hayden Stone then abandoned their option. In the spring of 1917, Messrs. Earle, Faskin and associates took an option on the property and started an extensive drilling campaign. This campaign accomplished approximately 18,000 feet of drilling and secured for the Faskin interests a 32 per cent interest in the property. In 1920, W. B. Thompson and The Mining Corporation of Canada secured an option, and, while this option was in force, sunk two shafts in the ore-zone and did a considerable amount of drifting and cross-cutting in the ore to study the manner in which it occurred in place, and, by actual channel sampling, to check the grade indicated by the previously accomplished diamond drilling. All of this work had indicated that an ore-body existed on the property containing at least 18,000,000 tons of ore, assaying as follows: gold, 0.074 oz./ton; silver, 1.06 oz./ton; copper, 1.71 per cent; and zinc, ). 45 per cent (1). Complete analyses of composites from the drill holes showed that the ore was very complex in character. It contained the above values in gold, silver, copper, and zinc, as well as large amounts of sulphur and iron, and traces of lead, arsenic, antimony, cobalt, and various other metals. Although the ore was obviously pyritic in character, pyritic smelting, the usual method of treating this class of ore, could not be used to beneficiate the ore with any reasonable expectation of making such a venture a financial success, since coke and coal landed at Flin Flon would be expensive, and siliceous flux was known to be scarce locally and low in grade. The property therefore lay idle until 1925.

Jan 1, 1935

By W. C. Whittaker

Introduction When one thinks of a coal stripping deposit, the picture that usually comes to mind is that of a more or less flat seam from two to twenty feet in thickness overlain by ten to fifty feet of overburden, in suitable ratio for economic operation. This is the usual type of stripping deposit and is quite a common occurrence in various parts of the prairie provinces. Rather unusual types of coal stripping deposits are being presently worked as open-cut mines by Sterling Collieries, Limited, and the Co al Valley Mining Company, Limited, at Miles 47 and 48 on the Alberta Coal Branch, some 150 miles south west of Edmonton. These deposits are of interest chiefly because they represent turned-up and greatly thickened sections of the Mynheer seam, and as such they present their own problems, peculiar to the commercial exploitation of a seam of this type. The area in which these deposits occur was originally owned by the Pacific Pass Collieries, whose operations, however, were confined to under-ground mining at Lovett, some eight miles to the southeast. It was not until l918 that the value of these deposits was realized, when the Company now known as Sterling Collieries, Limited, opened their pit at Mile 47. At the inception of the work, coal was loaded directly into the railway cars by men using wheelbarrows. In 1920, a tipple was built, after which the coal was loaded by steam shovel into mine cars, hauled by steam dinkeys, and loaded over the tipple into railway cars. In 1922, the Coal Valley Mining Company entered the field at Mile 48, with an entirely mechanical equipment, and at the present rime these two are the only stripping properties in Alberta using mechanical equipment both for the removal of overburden and the loading of the coal. These Companies have operated continuously since that time, and have to date mined and shipped 4,000,000 tons of coal, and moved some 5,255,000 cubic yards of stripping. The present annual coal output for the two mines is about 240,000 tons.

Jan 1, 1935

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By T. J. Fee

Introduction The International Nickel Company have been pioneers in mine rescue work in Ontario. Following the fire in the Hollinger mine in the spring of 1928, the Company purchased ten self-contained oxygen breathing outfits, ten all-service gas masks, an oxygen high-pressure pump, life line, inhalator, ten cap-lamps with batteries, and a complete stock of spare and accessory parts. An instructor from the U.S. Bureau of Mines, Pittsburgh, came to the Creighton mine for one week and trained twenty men in the use and limitations of all equipment. Monthly training courses were commenced in the fall, and have continued to the present time. Of the original twenty men trained, ten are still on the Creighton mine rescue teams. In the meantime, and as an aftermath of the Hollinger fire, the Work-men's Compensation Board of Ontario and the Ontario Department of Mines established a central mine rescue station at Timmins. This was completed in the spring of 1930. It was then decided, in view of the great expansion in mine development in the Sudbury district, to build and equip a similar station to serve all the mines there, namely, Creighton, Frood, Garson, Falconbridge, Sudbury Basin, and Errington. An extensive survey was made and a central location selected opposite the Frood mine. The International Nickel Company donated a site, and the station was completed in the fall of 1930. The station is a two-storey brick building, 27 ft. by 47 ft., with a large garage adjoining it. The ground floor is used for equipment and for training the crews. On the second floor are living quarters for the superintendent and his family. The garage houses a closed truck, in which all necessary equipment can be taken to any desired point for training purposes or for actual mine rescue work, if and when necessary. The garage is also used as a gas room, where the men are trained in an irrespirable atmosphere. A gas-tight observation window between it and the training room enables the superintendent to see and direct the men undergoing training, weight exercisers and other devices being used.

Jan 1, 1935

By W. F. Baker

Location and History God's lake is in the northeastern part of Manitoba, about 400 miles northeast of Winnipeg, or about 250 miles due north of Red lake, Ontario. The lake is quite large, having an overall length of 54 miles and a maximum width of 18 miles. There are numerous islands in the lake, the largest of these, known as Elk island, being about 15 miles long and 3 miles wide in the widest part. The accompanying map (Figure 1) shows the location of God's lake and of the mine. The God's Lake area has long been regarded as promising country for the prospector, but, due to its inaccessibility, practically no prospecting was done prior to 1927. In the years 1927-1931, inclusive, a few prospectors visited the area, but no discoveries were made. In 1932, Bob Jowsey and Archie McDonald entered the area from Island lake. They first prospected in the vicinity of Knife lake, which is immediately south of the main part of God's lake, and then moved on to the latter lake, heading for the north shore of Elk island. The first afternoon on God's Lake, when looking for a place to camp on the north shore of what is now known as Jowsey island, Jowsey discovered a quartz porphyry dyke which was cut by a number of gold-bearing bluish quartz stringers. On the strength of this discovery, he and McDonald began at once to stake the Reno group of claims. Rumours of the discovery brought in other prospectors, and other groups of claims were staked to the east, along the north shore of Elk island. A second discovery was soon made by Dan McCrea on his Gold Standard claims, three and a half miles to the east of the original discovery. Staking still continued to the east, along the north shore of Elk island, and Bob Brown and Harvey McKenzie staked the Akers group on a discovery approximately two miles east of McCrea's discovery. Through the efforts of Jowsey, the Reno, Rand, Elk, and Cona groups, belonging to the original syndicate for which Jowsey and McDonald staked, were combined with the Gold Standard, Greenstone, and Akers groups, and the Company known as God's Lake Gold Mines, Limited, was formed. Several additional groups of claims were later taken over by the Company and a considerable area of adjoining ground was staked to round-out the property.

Jan 1, 1935

By R. W. Davis

INTRODUCTION CHURCHILL river was named for John Churchill, first Duke of Marl-borough and third Governor of the Hudson's Bay Company, in the latter part of the 17th century, some fifty years after the ill-fated Danish expedition, led by Munck, had abandoned the site of the now famous seaport of Churchill, as a worthless, cold, disease-ridden country. No other attempts were made to explore the interior until the river basin became a part of the grant to the Hudson's Bay Company and began to play its part in furnishing the luxury of fine furs to civilized people as it had furnished the necessities of food and dress for untold centuries to uncivilized natives. This was the sole contribution of the region to the economic life of the country for some two hundred and fifty years, until 1926, when the power site at Island Falls was discovered by engineers seeking a cheap power source to make possible the development of the great ore-body at Flin Flon. DRAINAGE BASIN OF CHURCHILL RIVER The river is some 1,325 miles long. Rising in the headwaters of the Beaver river, in east-central Alberta, it flows in an easterly direction across Saskatchewan and northeasterly across Manitoba to Hudson bay, through a remarkable basin of some 115,500 square miles, only 6,000 square miles less than the area of the British Isles. A journey down this river leads one through three distinct belts of country, each vastly different from the others geologically and in surface characteristics. For the first five hundred miles the river flows through a basin of 36,000 square miles of the great central-plains country, which is covered with fertile soil and carpeted in its southern part with prairie grass, which gradually gives way to the mixed forests of poplar, spruce, birch, and jackpine in the northern and eastern sections: About midway across Saskatchewan, bald-headed knolls and ridges begin to make their appearance as the river meets the western margin of the Canadian Shield. Then, for some seven hundred miles, it passes through country underlain by the pre-Cambrian rocks of the Shield, which continue to within one hundred miles of Hudson bay. Here the character of the country again changes to a low, clay plain underlain by sandstone, and through this 'clay belt' the river flows between steep clay banks, to empty into Hudson bay.

Jan 1, 1935

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By A. E. Hilder

Introductory The following pages present the results of field investigations, laboratory and commercial tests, drilling, surveying, and preliminary development of the refractory clays which have been discovered recently in the township of Kipling, at the foot of Long rapids on the west side of the Mattagami river about 57 miles north of Kapuskasing and approximately 7 miles north of Smoky Falls, the terminus of the privately owned railway operated by the Spruce Falls Power and Paper Company, Kapuskasing (see Figure 1). Investigations on the clays of northern Ontario have been carried on over a period of seven years by officers of the Ontario Department of Mines, and I am indebted to the information published by that Department in reports by W. S. Dyer and A. R. Crozier, as well as?by Professor R. J. Montgomery, of the Ceramic Department, University of Toronto. It was, in large measure, the data given in the 37th, 38th, and 42nd Annual Reports of the Ontario Department of Mines that led me to make a personal investigation of the Mattagami River clays, with the result that we now have a commercial undertaking that will develop eventually into an industry of considerable importance in supplying the central manufacturing districts of Canada with refractories that heretofore have been largely imported from the United States. An extract from the 42nd Annual Report of the Department, Part III, 1933, page 75, reads as follows: "As for the refractory clay, the deposits are undoubtedly very large, but what is urgently needed is a deposit near the railway under sufficiently shallow overburden for recovery by stripping'. Having previously made an investigation of the clays adjacent to the Temiskaming and Northern Ontario railway, and these clays proving unsuitable, I turned my attention to the outcrops of refractory clays on the Mattagami river, first reported by Keele in 1919. This area offered possibilities within the economically permissible distance from rail transportation.

Jan 1, 1935

By G. F. Doggett

In describing accounting methods at Lake Shore Mines, it is the intention of the writer to limit the discussion to the principal features of the system used in securing cost figures and other statistics. The subject can be conveniently treated under the following divisions: (1) Time-keeping and Labour Distribution (2) Supplies: Handling and Distribution (3) Method of Assembling Data for Cost Purposes (4) Details of Operating Costs Time-Keeping and Labour Distribution After a new employee has gone through the routine of being 'hired on', he is assigned an employment number corresponding with the group applying to his occupation. This is for identification purposes in the plant and time office. He is also given an individual serial number, the use of which will be refer-red to later. On entering and leaving the plant, each employee passes through the clock room adjoining the time office, where he registers the time in and out on time recorders, on the clock card (Figure 1) bearing his name and number. It is the duty each morning of the time clerk to extend the hours worked by each employee, as indicated by the clock for the previous day, and at the end of the half-month period the total hours are multiplied by the rate and entered in the space provided for total wages at the bottom of the card.

Jan 1, 1935

By G. Vibert Douglas

Introduction A preliminary paper dealing with the subject of ore-shoots was presented to this Society at its Annual Meeting last year (1). The present paper records the attempts which have been made during the interval to further this study. In reporting this work, I wish to state that I do not consider the investigation complete; many more experiments will have to be carried out, and more field data will have to be recorded, before the geologist can say with confidence an ore-shoot should start at this point and pitch in that direction. The aim of these experiments is to find some criteria which will serve the mining engineer and mining geologist concerned with ore-shoots in hydrothermal veins.

Jan 1, 1935

By T. L. Tanton

Introduction Sturgeon River area, on the east side of lake Nipigon, Ontario, was the scene of a gold rush in 1934. According to press reports, the active staking during the latter part of the summer spread out rapidly from the early holdings until it embraced practically all of the lower basin of Sturgeon river in a belt up to ten miles wide extending west from Kinghorn for 35 miles to lake Nipigon. And, before winter set in, active prospecting and claim staking reached beyond lake Nipigon to areas where belts of ancient schists were known, notably west of Obonga lake. The writer's familiarity in past years with the areas to which attention has been directed admits of some observations on means of access in the field, the general geology, and the progress that has been made in identifying formations favourable for the occurrence of gold. Canoe Routes From the writer's observations in Sturgeon River area in 1917 and in the Obonga Lake area in 1933, it is recalled that there is, locally, a striking dif~ ference in the accessibility of the two areas by travel along canoe routes. Sturgeon River area is easily accessible from Kinghorn or Jellicoe stations on the Canadian National railways. Many small lakes, commonly of the linear type and with elongations east and west, occur among the forested rocky ridges near Jellicoe (Figure 1) and to the east and west along, or adjacent to, Sturgeon river. This stream has long stretches with gentle current between the falls and rapids. The drainage system provides excellent canoe routes (Figure 2), and the interruptions to travel (Figure 3) are remembered .as scenic features that were passed by portages with firm footing. West of Obonga lake, the streams flowing easterly to lake Nipigon may be followed through scenic canyons to a plateau of law relief characterized by extensive muskegs and shallow, brown-water lakes; and along small streams, where beaver dams have been destroyed, there are muck ponds where the usual alternatives of paddling or portaging can be dismissed in favour of the 'moosing' method of progress with the canoe (Figure 4).

Jan 1, 1935