Search Documents

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934

By E. Y. Dougherty

Introduction As practised during the last two years at the Vipond Consolidated gold mine, mining geology has meant the application of geology to the problem of finding, developing, and mining ore. This article reviews the results attained in Vipond mining geology as thus defined. Most effort was directed toward clarifying and interpreting the tangible physical causes of vein and ore localizations, and in the following pages these questions are dealt with in considerable detail. Discernment of the influence of rock folding and deformation on the localization of veins, and of the influence of certain structures and rocks in or near carbonaceous zones on the localization of ore-bodies, have been the main practical results of the studies. Consideration of some of the geological features of the Porcupine area, and of the geology and mining experience of the principal producing mines, has helped toward a perspective of Vipond's ore-finding problems. These features are first discussed. The background and procedure for Vipond mining geology, and the major results of the geological mapping, are then summarized. Then follows a résumé of tangible factors that influenced vein, ore-body, and gold localizations; and, next, explanations of the facts ascertained. Because they were found of little utility, many fascinating problems, such as the origin and mode of emplacement of the veins and lodes(l), the ultimate source of the ore, and the physico-chemical and mechanical agencies affecting vein and ore formation, are treated cursorily or are neglected in these notes.

Jan 1, 1934

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934

By M. Y. Williams

Introduction During the economic investigation of Pacific Great Eastern Railway subsidy lands, the P.G.E. Survey of Resources made a geological and mineral survey of a large part of the valley of the Peace river as included in the Province of British Columbia. The immediate valley of the Peace river was surveyed from the mountains to the Alberta boundary; the valley of the Pine river was surveyed throughout; and the Dominion block, 70 miles square and lying astride the Peace river, westward from the Alberta boundary, was very carefully surveyed. The writer was in general charge of the field work, and spent half the field season of 1929 and the field season of 1930 in the region . J. B. Bocock, however, did the major part of the work, spending two seasons, 1929 and 1930, in the area. General Conclusions The rock formations within the area discussed are all sedimentary and range in age from pre-Cambrian to recent. As might be expected, the minerals are in the main non-metallic, coal being by far the most important. Favourable conditions exist for natural gas occurrence, and suitable structures for petroleum concentration occur, although the high carbon ratio of the coals sheds considerable doubt upon the actual occurrence of oil in the area. Materials of minor interest are ochre, calcareous tufa, marl, limonite, gravel, and building stone.

Jan 1, 1934

By George R. Elliott

Introduction The pages that follow present a brief chronological survey of views which have been held, and of legislation enacted, for the regulation of the natural gas and oil industry in the Turner Valley field, especially as regards conservation of the natural gas. To provide a necessary background for an adequate understanding of the progress of events in western Canada, there is included also a compilation, from technical and legal authorities, of some of the more important measures which have been adopted for the regulation of the oil and gas fields of the United States, where these measures have had, or are likely to have, a bearing on the course of our domestic industry. Owing to exigencies of space, it has been possible to refer only to the most outstanding proposals and legislation, and to these in the briefest possible form. Although, so far as Canada is concerned, the data presented are restricted almost entirely to the Turner Valley field, it is the hope of the writer that the paper may prove of value for purposes of reference: for any similar gas and oil fields discovered in western Canada will certainly revive and intensify the problem of the proper steps to be taken for the conservation of the gas. Definition of 'Conservation The term conservation has been so misunderstood and misrepresented that, to many persons in Alberta, it means little more than closing-in wells. In the light of the definition of Charles E. Hughes, that 'True conservation of a raw material is its economical use', the subject of natural gas conservation is inseparably involved with the study of the function of the -gas and with the development of the principles of unit operation.

Jan 1, 1934

By E. D. Fox

Introduction The financial statement of the hypothetical Gold Mining Company, which forms the background of this survey, was designed for the Institute with the express abject of having it assessed in respect to Profits by the several taxing bodies representing the Federal and Provincial Governments, which comprise the Dominion of Canada. On the completion of the figures, copies were sent to the several Ministers of Mines, accompanied by a request that they be submitted to their taxing authorities and assessed accordingly. The response, while it was not general, was very favourable, and at all times we were treated with the utmost courtesy and patience, and what has been set forth in the compilation bears the authentication of the various government officials who are immediately concerned with taxation. The data itself constitutes a fairly comprehensive digest of taxation as it directly applies to gold mining profits in Canada. The Hypothetical Balance-Sheet (See Exhibit A) In the balance-sheet schedules 1 and 2 (Exhibit A), income is divided between taxable and non-taxable classifications, and here it should be noted that the division contemplates only the assessment for Dominion income tax. The same applies to the factors of exchange and depletion. Therefore, in making comparisons, it is to be borne in mind that the set-up for assessment to the Provinces, that is, Manitoba and Alberta, will stand as if the gross non-operating income is taxable, with the reservations as shown in the notes below the schedules.

Jan 1, 1934

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By R. W. Diamond

Introduction THE Sullivan mine and the milling, smelting, and refining operations of the Consolidated Mining and Smelting Company are sufficiently well known to make unnecessary anything more than a very brief account of the events which led up to this Company's branching out into the chemical industry. This development is the result of the 26 per cent sulphur content of the Sullivan ore. Seventy-five to eighty per cent of this sulphur enters the mill tailing, which is stocked at Kimberley. The remainder, contained in the lead and zinc concentrate, is burned off in the first treatments at Trail. Prior to this new development, the sulphur gas was wasted to the atmosphere. In spire of its great dilution with air and discharge from stacks at high elevations above the plant, some damage to vegetation close to the plant was experienced. It had always been apparent that this sulphur should be recovered and utilized if possible, at the same rime relieving, or curing, the smoke nuisance, and constant studies with this in view had, therefore, been maintained. One of the early conclusions reached was that the Canadian prairies would ultimately require large quantities of phosphate fertilizers, as had been the experience of older countries, and that these fertilizers would constitute a large outlet for sulphuric acid which could be made from smelter gases. This conclusion prompted a widespread search for phosphate rock, particularly in British Columbia and western Alberta, with the result that low-grade beds were discovered in the Crowsnest district and to the north therefrom through extensive areas (1). Following these discoveries, an experimental plant was built at Trail for the production of triple superphosphate in order to facilitate field-tests in fertilizing prairie lands.

Jan 1, 1934

By Victor Dolmage

Introduction Although gold production in British Columbia began in 1859, lode gold was not produced till 1893. Since 1900, the annual production of lode gold has fluctuated between $3,000,000 and $6,000,000. About twenty per cent of this production may be regarded as by-product gold from base metal mining. The remainder comes from a few isolated but important mines, such as the Rossland mines, Nickel Plate, Surf Inlet, Premier, Pioneer, Bralorne, Reno, and Cariboo Gold Quartz, and from several less important mines. All of the above, except Pioneer, Bralorne, Reno, and Cariboo, are approaching or have reached the point of exhaustion, but all are now receiving, under the stimulus of the. present gold-mining boom, drastic resuscitative treatment, with, in some cases, signs of resurrection. Notwithstanding this, however, the main interest at the present time is focussed on the Bridge River and Cariboo fields. Both these fields were discovered in the early 'sixties' and, apart from the Cariboo placer production, both have from time to time contributed small amounts of lode gold; but it is only during the last two years that the real possibilities of these areas were discovered. and that they began to assume the appearance of goldfields of major importance. The two fields are sorme three hundred miles distant from one another and contain deposits of distinctly different types, so that the only reason for including them in one article is the fact that they came into prominence more or less simultaneously and at a time coinciding with, but not otherwise related to, the present gold-mining boom.

Jan 1, 1934

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a 'cement-gun'(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World's Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By A. Hasselbring

Sub-Level stoping was used in this country at least as early as 1912, at the Magpie mine in Michipicoten. The fundamental principles of the system are the same wherever it is used, but modifications have been adopted in the Michigan iron mines and in several Canadian mines. It is a system whereby a suitable body of ore may be developed quickly and worked cheaply, with a low initial expense, and by miners of quite ordinary ability. The basic method, described in the following pages, may be modified to meet conditions where one or more factors are not in accord with normal sub-level stoping requirements. In suitable ground, sub-level stoping is probably the most satisfactory method yet devised for underground hard-rock mining. It is so simple, straightforward, and safe that no special training of a crew is necessary. Any miner capable of drifting and raising can carry on the work necessary for sub-level stoping after the shaft has been sunk. The method is suitable, however, only for reasonably wide ore-bodies, the minimum width of ore to which it can be economically applied being somewhere in the neighbour-hood of thirty feet. The development programme is simple. Assuming, for purposes of illuslustration, an ideal ore-body, two thousand feet long, dipping nearly vertical, and varying in width from forty to a hundred feet, this programme would be as follows. The shaft should be sunk on the footwall side about sixty feet outside of the ore-body and near its centre. Levels are then established at suitable intervals, usually 125 feet. On each level, a cross-cut is run to the ore-body, and there a main-haulage drift is driven in either direction to the end of the ore. Cross-cuts are then run at 25-foot intervals, so that ore-chutes can be spaced about 25 feet centre to centre each way. It is not necessary that these cross-cuts be extended to the walls of the ore-body, if the position of the walls is known; they are extended just far enough to make room for the correct location of the chutes.

Jan 1, 1934

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By W. B. Burchall

Introduction In presenting this paper the author wishes to state that the opinions here given represent only his personal views. A general survey of the subject has been attempted, but such deductions as may have been drawn are not necessarily endorsed by the Company with which he is associated. The aeroplane as an instrument of transport is yet a novelty, for it is only twenty-five years since man first flew. This statement, by itself, may be very deceptive, for compared with the steam locomotive or even the auto-mobile, this infant in industry has made some remarkable showings. The 'actual performance' speed-curve of aircraft plotted over a ten-year period is rising faster than the 'expectancy' speed-curve of 1924 indicated, and it should be noted that, today, the possibilities of 600 miles per hour provoke less scepticism than did the prophecies of 400 miles per hour only a decade ago. Commencing with the remarkable achievement of raising one man into the air, aircraft with an all-up weight of 14 tons are now in daily use on the British airways, and recently a non-stop flight of 5,340 miles was accomplished in an aeroplane, without refuelling. More true than ever is the statement that the records of yesterday are commonplace tomorrow, for new ideas are today seized on and exploited to the utmost once the period of scepticism and doubt has been overcome. In fact, so many new ideas have been brought forward, during the past few years, and applied successfully in our economic life, that one may well ask if today we are not a little too impatient, too exacting in demands, forgetting that real worth-while progress -is attained by no short-cuts.

Jan 1, 1933

By Oliver Bowles

Cementing materials of mineral origin were well known to the ancients. Ordinary lime and gypsum plasters were the first to be recorded by historians. The next development was the discovery that certain limes would set under water, but the hydraulic property was not definitely attributed to the presence of clay in the limestone until many centuries later. The Romans advanced a step nearer to modern cement in the development of 'pozzuolana', a mixture of volcanic ash or trass with hydrated lime. The silicate of aluminium in the volcanic rock combined readily with the lime, forming a hydraulic mortar or cement which was widely used. Natural Cement In Europe (1) No further progress was made in the art of manufacturing cement for several centuries, during which the Roman Empire declined and passed away, and the Anglo-Saxon race slowly and painfully evolved through the Middle Ages an ever-increasing prestige. An Englishman, John Smeaton, is credited with the honour of the next important development, for he employed a little-known cementing material-natural cement-in constructing the Eddystone lighthouse in 1756. It was called 'natural' cement because it was made from a natural rock with no additions of other materials. The process consisted of calcining an argillaceous limestone at a comparatively low temperature and grinding the product to a fine powder. Care was exercised to keep the temperature low, and any material burned to the clinkering point was thrown away, although such material was, as learned at a later time, Portland cement.

Jan 1, 1933

By J. R. Gordon

I-Introduction The possibility of adapting low-temperature reduction methods to the treatment of iron ores has been suggested on numerous occasions. Papers published on the subject include, notably, Bulletin 270 of the United States Bureau of Mines on The Production of Sponge Iron, the Symposium of the American Electrochemical Society (1927) on The Gaseous Reduction of Ores and Other Metallic Compounds, and Les Procédés Actuels de Traitement Direct du Minerai de Fer, by A. Mayer (Revue de l'Industrie Minerale, Nov. 15th, 1932) (1). The present paper contains the results of an investigation of the reducibility of some Ontario ores. The concentration of these ores and of the products of reduction has also been investigated.

Jan 1, 1933

By A. W. JR. Whitaker

Introduction Within the last quarter of a century the Lake St. John-Saguenay valley has been converted from a quiet agricultural district to one of the important industrial centres in the Dominion. First there was the expansion -of the pulp and paper industry, and then, starting a little over ten years, ago, the development, in large .blocks, of the enormous hydro-electric power resources of the Saguenay river. Coincident with this power development, the world aluminum industry was rapidly expanding and looking for a new source of cheap power. This was found in the Saguenay valley-and so, in 1925, Arvida was established by the Aluminum Company of Canada as a location for one of the largest aluminum plants in the world. Arvida, an incorporated city comprising an area of some ten square miles, is ideally located on a more or less level plateau about 350 feet above the Saguenay river. Seldom has industry stepped boldly forth and carved out of Nature a community with full city status. The process usually goes through the steps of camp, village, town, and city, involving improper planning or lack of planning; all of which has been avoided at Arvida by starting out in the right way. While this community has only a population of approximately 2,000 at the present time, it is carefully planned for a population many times this figure. Streets, city parks, business and residential sections, have been definitely planned, and, with a City government, proper ordinances were passed at the beginning to ensure the building and maintenance of a model industrial community. As the crow flies, Arvida is about 35 miles due east of lake St. John, and 0 miles west of the St. Lawrence river at Tadoussac. From a shipping standpoint, it is well served by the Canadian National railways, with direct lines to Quebec and Montreal, and by ocean shipping facilities at Port Alfred, which is about 15 miles to the east on the Saguenay river and is served by the Roberval & Saguenay railway. The latter has interchange connections with the Canadian National at Arivda, and also operates a branch line into the city of Chicoutimi.

Jan 1, 1933

By W. E. Johnston

At last year's Annual Meeting a paper by Haultain and Johnston was presented entitled Is the Gold in Tellttrides Soluble in Cyanide? Since then the writer has continued the study of various phases of this problem. Samples and specimens of ore from some of the Kirkland Lake mines have been studied and non gold-bearing tellurides have been found in these that are not soluble in ordinary mill solutions. Samples of tailings, both old and recent, from this district have been examined with apparatus and methods that have proved very successful in detecting the presence of extremely minute quantities of tellurides. Tellurides, both base-metal and gold-bearing, have been discovered in these tailings, but only in such minute quantities that their presence would not affect the ordinary assay results. More free gold particles have been found in the tailings than gold-bearing tellurides. Much experimental work has been done on tellurides, concentrated from high-grade material and from ordinary run-of-mine ore. The gold-bearing tellurides behave very much as does gold itself. Finely divided particles are dissolved fairly rapidly, coarser particles more slowly. All the tellurides are soft and brittle and also have a high specific gravity, with the result that they are extremely finely divided in ordinary mill practice. The ordinary high-lime solution of Kirkland Lake practice is suitable for the dissolving of the gold tellurides. Oxygen is necessary, but apparently not more so than in dissolving gold. Some particles have been found that appear under the microscope to be ordinary metallic gold particles, but on heating they show a small telluride content. These appear to dissolve more slowly than gold. There is considerable variation in the ratio of tellurides to gold from different points in the mines. So far the writer has failed to find any connection between this ratio and the richness of the ore. Generally speaking, the base-metal tellurides predominate. Some of these contain gold but this may be due to a mixture of tellurides in the one particle.

Jan 1, 1933

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933