Search Documents

By O. Lashkari

Swirled Enthalpy Equilibration Device (SEED) is a new patented Slurry-on-Demand, SoD, processing route. The semi-solid slug preparation is carried out by off-center swirling of aluminum melt in a metallic mould. As part of the current research program on the semi¬solid processing of aluminum alloys, the morphological evolution of 356 aluminum foundry alloy microstructure is reported here. Semi-solid slugs were prepared using two different pouring temperatures of 645°C and 695°C respectively. Morphological evolution of the semi-solid microstructure was characterized using image analysis through measuring of primary a-Al particle size, number density, aspect ratio and sphericity. The possible relationships between microstructural features and process parameters were also investigated. The current report covers the effect of pouring temperature on the morphology of primary a-Al dendrites and attempts are made to explain the differences between the predicted percentage primary a-Al phase and those of the actual values in the as-cast slugs.

Jan 1, 2004

By Jean Scott, G. A. Collins, G. W. Hodgson

WHILE it is well known that trace metals in crude •oils and distillates have been a matter of deep concern to refining engineers because of the damage done .by the metals to cracking catalysts and refractories (8, 5), the trace metals in crude oils may be of great benefit in correlation studies and in origin studies. During the geological processes in which the oil is formed from •animal and vegetable life, the hydrocarbons are subjected to a host of inter-related reactions, both physical and chemical. It has been well demonstrated that the lighter materials, certainly the short-chain paraffin hydrocarbons, are degradation products of the heavier molecules, and it might be concluded that for correlation studies it would be advisable to direct attention as much as possible not to the degradation products of the large molecules but to the large molecules themselves. Be this as it may, the methods at •hand to conduct the study are not particularly precise and, in the past, attention has centred on the simpler small molecules, as evidenced by the great mass of work involving distillation and chromatography with painstaking separation of the simpler 'front-end' hydrocarbons.

Jan 1, 1954

By Martin Grenon

This paper presents two case studies where fracture set orientation was quantified using three methods: a simple fracture pole grouping, a Fisher distribution and a Kent distribution. The three fracture orientation representations were then used as inputs for kinematic slope stability analysis. Differences showed up in the probability of sliding for all instability modes considered.

Aug 1, 2013

By Bruce Mennie

PT Freeport Indonesia (PTFI) operates copper and gold mining operations in a mountainous area of the Mimika regency, near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. The mining and concentrating operations typically produce 240,000 metric tonnes per day of Copper and Gold ore from the combined mining of an 80,000 tonne per day (ore) block cave operation (DOZ Mine) and a 160,000 tonne per day (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open pit mine will be complete in 2016 at which time PTFI?s operations will convert to Underground. Mining operations will transition from today?s mixed surface and underground operation to full underground mining over the next 6 years. This paper reviews the history of Redpath?s relationship with PTFI, beginning with a raiseboring contract in 1981 and evolving into vertical and horizontal development contracts of up to 37,700 equivalent metres of lateral development and 4,000 metres of vertical development in 2011. An overview of the current operations (PTFI?s Grasberg Open Pit and DOZ Underground Mines) and transition period (challenges for the transition from current to future underground mines) is presented with details of development of common underground infrastructure and future mines; Big Gossan Mine, DMLZ Mine, Grasberg Block Cave Mine, and the Kucing Liar Mine.

Oct 1, 2010

By C. E. Baltzer

This paper highlights the position of coal supply in regard to the requirements for electric-utility operations. The text and the appended tables outline the trend of thermal power development and fuel use in the electric-utility industry. Mention is made of several argumentative factors influencing the use of coal in relation to competitive oil and gas, and of the importance attached to developing a realistic understanding of the respective problems faced by the supplier and consumer of coal. * * * TREND OF" THERMAL POWER DEVELOPMENT T HE RATE OF ADVANCE in thermal power has been significant during recent years, particularly in the Atlantic Provinces, the Prairie Provinces, Ontario, and British Columbia. While dependence on thermal power in Quebec and the Northern Territories is less than in the remainder of Canada, these regions also eventually will have need for increased amounts of such power.

Jan 1, 1961

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which 'bonanzas' occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the 'indicator' deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934

By Asanga S. Nanayakkara

The surface deformations induced by reservoir dilations can be measured using tiltmeters and these measurements can be used to infer reservoir level volume changes by solving an inverse problem. Preferred approach to solve such an inverse problem is to consider more tiltmeter measurements than the number of unknown variables considered in the inverse problem. However, sufficient number of measurement points is not always available due to economical and practical issues. This paper proposes a new approach to circumvent this problem. The new approach entails generation of pseudo surface deformation data by curve fitting tiltmeter measurements using a mathematical function, which delineates three-dimensional characteristics of surface deformation profiles. Then a three-dimensional inverse problem is solved using pseudo surface deformation data. This method is useful in inferring reservoir volume changes with high areal resolution when the number of available measurements is not sufficient to acquire the desired areal resolution.

Jun 1, 2012

By William J. Davis, R. Blair Hrabi, Sally Pehrsson, Amelia V. Logan, Ross Sherlock

"Abstract - The Meadowbank gold deposits are hosted by a series of polydeformed and metamorphosed auriferous iron formations located in the Neoarchean Woodburn Lake group, western Churchill province, Nunavut. The supracrustal rocks in the Meadowbank area consist of a thick sequence of intermediate-composition volcanic rocks with intercalated iron formation, ultramafic volcanic rocks, and quartzite to quartz arenite. U-Pb geochronology gives an interpreted age of 2711 ± 3 Ma for the host strata at Meadowbank.The intermediate volcanic rocks are predominately volcaniclastic and have a geochemical composition that is consistent with an active continental margin setting. Iron formation deposition was coeval with the intermediate volcanism, as indicated by incorporation of volcanic detritus in the chemical precipitate. The geochemistry of the iron formation indicates that it precipitated from a fluid that at one time was at high temperature (>250°C), reducing, and likely acidic. Intercalated ultramafic rocks rarely show spinifex textures and have trace element ratios that are consistent with mantle plume-related undepleted mantle asthenosphere, likely recording episodic mantle upwelling associated with rifting in an active continental margin. The contact between the ultramafic volcanic rocks and the overlying quartz arenite is a disconformity marked by a quartz pebble conglomerate. However, similar geology on the structural hanging wall and footwall of the contact suggests that the conglomerate does not represent a significant hiatus in deposition, and is more likely a prograding terriginous siliciclastic unit.Three metamorphic events are recognized. The first, M1, is a cryptic greenschist facies event that is pre-D2. The second event, M2, is a mid-greenschist to amphibolite facies, syn-D2 event. M3 is the last event recognized, and is a post-tectonic greenschist facies event that is regional but inhomogeneous in extent, possibly reflecting thermal aureoles around post-tectonic 1.7 to 1.8 Ga Nueltin granites. The structural geology of the area is complex with four phases of deformation recognized, two of which had a significant effect on the geometry of the deposit. All of these regional events are interpreted as Paleoproterozoic in age. Relationships between deformation fabrics and mineralization, as well as the overall geometry of the mineralized envelopes, suggest that the deposit formed during syn- to late-D2. Superimposed on the mineralization are D4 structural elements that postdate gold mineralization.The main control on gold mineralization is replacement of magnetite by pyrrhotite and pyrite in high-strain corridors. The composition of amphiboles and chlorites associated with gold mineralization is remarkably consistent and shows no spatial or temporal variation, suggesting that it was buffered by the iron-rich nature of the host rocks. The bulk metasomatic effect on the intermediate volcanic rocks is characterized by the addition of K2O and the loss of CaO, Na2O, and MgO, with little variation in the total iron content. The elemental losses are likely the result of destruction of feldspars, stilpnomelane, and ferroactinolite, which are relatively common in the unmineralized rocks, and the formation of sericite, chlorite, and grunerite."

Jan 1, 2004

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth's crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By J-F. Turgeon, Y. Pépin, G. Hudon

The high temperature hydrochloric acid leaching of titanium slag in the QIT upgraded slag process (UGS) creates a harsh environment for materials of construction. Because of their excellent chemical and heat resistance, furan mortars are a key component in the lining system of the UGS pressure leach reactors. Similar products coming from different manufacturers have however shown unequal performances in service. In some cases, cracking of the brick lining has occurred during curing of the mortar. This study was initiated to investigate the impact of the curing conditions on the properties of carbon filled furan mortars. Laboratory tests were conducted to assess the effects of temperature and exposure to water and HCl solutions on mortar shrinkage and mechanical properties (tensile, compressive and bond strength). Three commercial furan mortars that have been used in the UGS leach reactors were thus characterized. Mortar properties were found to vary significantly among the products tested. Moreover, the curing conditions were shown to have a significant impact on mortar shrinkage and mechanical strength. The experimental findings provide explanations for the unequal performances of the mortars in service and for the problems of brick lining cracking that occurred in the UGS leach reactors. This study demonstrates that excessive mortar shrinkage compromises the integrity of a brick lining system.

Jan 1, 2004

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By Dwayne D. Tannant

This paper presents a summary of results from a questionnaire sent to surface mines in western Canada seeking information on haul road design, construction, and maintenance. There has been a marked increase in the size of the trucks used over the last decade with some mines now using trucks with a payload capacity of 360mt. Consequentially, geometrical elements of haul roads, such as width, have been enlarged to accommodate larger trucks. Most haul roads are constructed on the basis of past experience without use of formal design procedures. With the introduction of larger haul trucks, problems related to rolling resistance, deterioration, and maintenance of the haul roads have become more important. This has lead to adoption of more rigorous design methods for roads at some mines, most notably for the oil sand mines operated by Syncrude Canada Ltd. A summary of the evolution of haul road designs implemented at Syncrude Canada Ltd. is presented.

May 1, 2001

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

By J D. McDonald

This paper outlines the function of the Safety and Compensation Division of the Mining Association of British Columbia. After a general discussion of safety and the safety program now being followed in B.C., the author goes on to describe the wide-ranging aspects of compensation payments and company assessment rates. Special attention is also given to the problem of silicosis in mining operations. In appendices to the paper, the experience rating plan of the mining industry is compared to that recently adopted for the construction industry. Introduction The Mining Association of British Columbia consists of fifty-five member companies, including virtually all the producing mines as well as the larger exploration, contracting and development companies. On completion of an extensive study of safety and compensation in the mining industry, the Mining Association of British Columbia instituted a Safety and Compensation Division in 1954. The director of the Safety and Compensation Division reports to the Executive Committee of the Association. There are two main functions of this Division. First is the prevenion of accidents by encouraging

Jan 1, 1965

By A. Dolatmoradi

Nanocrystalline structure formations produced by severe plastic deformation in Fe-0.15C with initial ferritic-pearlitic and IF steel with ferritic microstructures have been studied through microstructural observation and microhardness measurements. It was found that the nanocrystalline region first forms near the surface of samples due to localized severe deformation. It was also observed that the nanocrystallization rate of Fe-0.15C and IF steels and the deformed layer thickness in these two materials are different with similar milling conditions. The crystallite size and structural evolution of the samples during milling was studied by employing XRD and SEM.

Jan 1, 2010

By O. Lashkari

Manipulation of pouring temperature is an efficient way to produce different microstructural features. In order to characterize the microstructure of rheocast billets due to different superheats of 615-695 °C, the parallel plate compression method was employed. Foundry 356 Al-Si alloy with different morphologies of primary a-Al particles were tested at different initial pressures of 4,8, 11,2 KPa, The resulted strain-time graphs were further treated mathematically to calculate viscosity of SSM billets. The interrelationships of viscosity, the microstructure and primary phase flow during compression are discussed, It is shown that the dendritic primary a-Al structure has the highest viscosity number which is almost three orders of magnitude greater than those for globular morphology, The current research have, for the first time, shown the validity and reliability of "parallel plate compression viscometry" method in characterizing microstructural evolution of Rheocast SSM billets.

Jan 1, 2005

By Y. Y. Yemelyanov, S. S. Gudkov, A. V. Boldyrev, A. V. Bogorodskiy, S. V. Balikov

"A series of tests to optimize pressure oxidation- carbon-in-leach process (POX-CIL) of goldbearing flotation concentrate with the addition of sodium chloride and activated carbon were carried out. Flotation concentrate which was generated during primary ores concentration from a large Russian deposit was used for these tests. The tests were performed with different concentrations of sodium chloride. It was found that the required sodium chloride concentration for gold leaching was 5 g/L. The tests performed with different additions of activated carbon showed that the amount of activated carbon should be at least 6% of the concentrate mass. The rate of sulfides oxidation was 67.7–99.8 %. The highest gold recovery was 98.6 %.INTRODUCTIONThe majority of gold-bearing ores are recommended to classify as amenable to cyanidation and refractory. Processes at elevated pressures and temperatures have become increasingly important in base metals hydrometallurgy (Lodeischikov, 1999, 2007; Naboichenko, Shneerson, Kalashnikova, & Chugaev, 2009; Thomas, 2005).Current pressure autoclaves – cyanidation flow sheets are capital intensive due to numerous circuits and the use of environmentally-unfriendly sodium cyanide. The use of halide-based lixiviants during pressure oxidation of precious metals can be a promising technique for refractory sulfide goldbearing mineral raw material hydrometallurgical processing (Fleming, 2002, 2007, Kotlyar, Meretukov, & Strizhko, 2005).In this paper, we presented the results of the research on finding the optimum process parameters of pressure oxidation using an adsorbent for a refractory gold-bearing concentrate. A proposed flow sheet involves (Bogorodsky, Yelelianov, & Balikov, 2012):1. Gold-bearing sulfides oxidation followed by precious metals dissolution and the formation of gold and silver chloride complex;2. Reaction of the precious metals chloride complex with a carbon-based adsorbent;3. Precipitation of precious metals onto the adsorbent by EW and smelting of cathode precipitates into Dore bullions.This process allows POX of gold-bearing sulfides, precious metals dissolution and their precipitation on the adsorbent to be executed in one single vessel. This study found that the most suitable lixiviant was sodium chloride. Fleming (2002) suggested that in the presence of a halide-based reagent (e.g. chlorine- ion reaction), the dissolution of gold during POX is achieved according to reaction 1:"

Jan 1, 2016

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By Don Langlois, Udo Weber

"The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected milling conditions of calcium carbonate. A variety of grinding media material and bead sizes, along with 2 different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data was used to calculate and evaluate specific energy as well as stress intensity under different milling conditions.INTRODUCTIONAs a result of increasing energy costs and raw material prices it is important to look at the efficiency of the manufacturing process. Wet grinding and ultrafine wet grinding in stirred media mills are now a possible cost-effective production step for the processing of industrial minerals and precious metals. The generation of smaller particle sizes (down to micrometer scale) can be advantageous for further production steps – i.e. better liberation of precious metals or improved industrial mineral qualities.In the following, the wet grinding process is investigated under different milling conditions of calcium carbonate. Different grinding media materials varying in specific weight, bead size and stirrer tip speeds are used to determine optimal energy consumption for the milling process.DESCRIPTION OF TEST CONDITIONS AND PARAMETERSMill ParametersTests were performed in a Drais Laboratory Perl Mill PML H/V with an installed electrical motor power of 3 kW. The mill chamber is silicon carbide where as the stirrer and discs are made of yttria stabilised zirconia. The mill working volume is 0.9 l. A screen cartridge with a screen size of 0.2 mm is used to separate the beads and slurry at the outlet of the mill. All tests were performed with a grinding media filling grade of 80% (Mill working volume). The stirrer tip speed was set at 6 m/s and 10 m/s."

Jan 1, 2009