Search Documents

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By Nelson Lawrence

An Electrical Risk Management/Inspection Program has been designed specifically for the mining sector in order to provide electrical code expertise and systemic gaps in electrical systems. Goals include improved safety and productivity, reduced injuries and help to enable businesses to better comply with the electrical codes and regulations that govern them. The Electrical Risk Management/Inspection Program is now recognized by some of the world?s largest mining organizations. Since June, 2001 these electrical safety advisory services have been available to underground and surface mine sites throughout Ontario and are now offered throughout Canada and around the globe. This program is also currently being applied to review new electrical installations for mine construction projects thus improving the safety and reliability of mine site electrical systems.

May 1, 2006

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By A. Lemay, G. Morin, C. Desmeules

"Incorporated in 1976, Sidbec Normines was mandated to exploit a deposit of specular hematite at Fire Lake. A combined effort of three companies, Sidbec, which holds 50. 1 % of the actions, British Steel Corporation another 41.67 % and finally Quebec Cartier Mining, a subsiduary of U.S. Steel Corporation, with still another 8.23 %.The deposit is located 60 miles north of the town of Gagnon. The extracted ore is crushed, in a giratory crusher, to-8 11 chunks, and from there, it is transported, by rail, to a concentrator at Lac Jeannine.A concentrate containing 65.5 % Fe and 5.5 % Sio2 is produced, using conventional methods like autogeneous mil ls and spirals. The concentrate is then transported by rail to the Port Cartier installations.The installations in Port Cartier include a secondary concentrator, a pellet plant, and stockpiling facilities for pellets and concentrate. The pellet plant has two product lines in paralel, producing a total designed tonnage of 6 millions tons of iron ore pellets, of which 3mi11ions tons are used in direct reduction furnaces.The secondary concentrator is designed to remove a portion of the silica contained in the ore, usually less than 2 % Si02 should remain from the original 5.5 % Si02 in order to produce iron ore pellets which are well suited for use in direct reduction and electric furnaces."

Jan 1, 1981

By John S. Stevenson

Zeballos mining camp is on the west coast of Vancouver island; 195 nautical miles northwest from Victoria.; The spectacularly rich gold-bearing veins that made Zeballos an important; gold camp were found early in 1934. Small pockets of very coarse; gold had been found earlier under large boulders at the mouth of Spud; creek; and in the autumn of 1933 rich gold-quartz float was found near the; mouth of the creek. The rocky beds of the steep creeks entering Spud creek; were searched for its source and as a result the veins on the White Star property; were found. The Goldfield vein on the Spud Valley property was discovered; in 1935; and the No. 1 vein on the Privateer in 1936. In the general; prospecting activity that quickly followed; other veins were found; not; only in Spud creek but in other creeks draining into Zeballos river.

Jan 1, 1954

By F. Siciliano, D. Bai, S. Yue, A. M. Elwazri

The influence of niobium addition and very low temperature (`cool') deformation on the microstructure and properties of low carbon microalloyed steels was investigated. In this work, the specimens were heated at 1200°C and held at this temperature for 20 minutes. Some specimens were aged at 400°C for times ranging from 10 minutes to 10 hours followed by air-cooling. Others were subjected to deformation at 400°C (`cool deformation') prior to aging. It was observed that the proportion of acicular ferrite was increased as the amount of Nb was increased. It was found that cool deformation increased both yield and tensile strengths significantly compared to that of the aged only specimens.

Jan 1, 2005

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By K Morrison

Different individuals have calculated the boundary stresses around elliptical openings in an infinite elastic medium for various conditions of loading. With caution, such calculations are useful in indicating stress trends in mining. This paper illustrates an application to caving operations and suggests that abnormal field stress would have an adverse effect. Introduction GELDART and Udd (1), applying elastic theory, confirmed, and set out graphically, the stress distributions on the surface of elliptical openings with axis ratios varying from 1.0 (a circle) to infinity (a crack). The loading conditions varied from uniaxial to hydrostatic, and inclinations for the opening, with respect to the stress axis, varied from 0° to 90°. As most mine openings can be generalized into this elliptical conception, the usefulness of the presentation lies in the fact that given reasonable estimates for the stress ratio, the axis ratio, and its inclination, then the trend in stress concentrations as an opening develops can be readily approximated.

Jan 1, 1964

By H. McIntire, R. Preston, D. Roberts

"Repeated 3D terrestrial digital photogrammetric surveys were conducted on hard rock mine pillars to characterize damage during secondary mining. Damage was quantified by measuring Depth of Failure, DOF, from spalling material and crack intensity, D21. These damage values were then correlated to visually assessed Pillar Damage Ratings and numerically estimated pillar loads. Measured damage, particularly Depth of Failure, correlated well with Pillar Damage Ratings. Numerical predicted pillar stress vs. damage exhibited the expected trend with shorter pillars being stronger. High resolution photographs and 3D models were also used to characterize damage mechanisms, which were found to be structurally constrained. INTRODUCTIONThe Doe Run companies Southeast Missouri Operations consists of six room and pillar lead mines (Brushy Creek, No. 29, Casteel, Buick, Fletcher and, Sweetwater) (The Doe Run Company, 2014). The mines are hosted in the Carbonates and Shales of the Viburnum trend with mining depths varying from 180 to 300 m. Pillars are commonly cut square with widths varying from 7 to 9 m and heights generally between 5 and 18 m, resulting in extraction ratios between 80 and 85% (Roberts et al., 1999). Figure 1 presents an idealized stratigraphic section through the Viburnum trend and Figure 2 shows a plan view of the five areas spanning the three mines included in this study."

Jan 1, 2015

By Patricia J. Dillon

Established in 1997, Prospectors and Developers Association of Canada Mining Matters (PDACMM) is a registered charitable organization dedicated to providing Earth Science education to grade school students. Through the development and distribution of educational programs and materials, PDACMM informs students of Canada?s geology and mineral resources as well as promoting awareness of the importance of rocks, minerals, metals and the mining industry. PDACMM also co-ordinates with other charitable organizations and government agencies to provide support or to work in tandem with them and reach as many young people as possible. Although PDACMM became a charitable organization in 1997, it actually has its? roots in 1994 when the Grade 7 program Mining Matters/Une Mine de Renseignments was developed to help teachers bring geology and mining into the classroom. Over 2100 of these resource kits were distributed to teachers across Ontario during the period 1995 to 1998. This unit won national recognition when it received the prestigious Partnership Focus award from the Conference Board of Canada for ?promoting science literacy for the world of work?. Due to the phenomenal success of these kits, a Grade 4 kit entitled Deeper and Deeper/Aller au Fond Des Choses was developed in 1998 in response to the opportunity provided by the new Ontario curriculum released at that time. Over 2600 of these kits were distributed throughout Ontario and there is a substantial waiting list of teachers hoping PDACMM will be able to raise enough money for another print run.

May 1, 2002

By A. F. Matheson

"The Jellicoe is the most westerly mine in the Little Long Lac area with a record of gold production. The property is largely covered with overburden and the ore deposit was found by diamond drilling along the projected strike of a gold bearing zone at Magnet lake 1 ½ miles to the east on the property of Bankfield Consolidated Mines, Limited. In 1940-41 Jellicoe mined the whole orebody of approximately 14,000 tons, recovering 5,620 ounces of gold.The vein is in light-coloured greywacke. A mile-long dyke of fine-grained quartz feldspar porphyry 5 to 10 feet in width lies 100 feet south of the vein. A similar, even longer dyke lies 700 to 800 feet north of the vein. Some narrow diorite dykes are also rather closely associated. The porphyry dykes are gold bearing, but not ore. The vein material is quartz and silicified and brecciated greywacke. Mineralization consists of native gold, pyrite, arsenopyrite, and some sphalerite."

Jan 1, 1954

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013

By A. R. Byers

"Porcupine Peninsular mine is at the extreme southwestern end of North peninsula in Night Hawk lake, Cody township, Ontario. It lies approximately 10 miles east of the gold-producing district of Porcupine.Gold in quartz veins was discovered on Gold -island in Night Hawk lake in 1906, the same year in which the now famous Porcupine gold camp was discovered farther west. Most of the claims now held by the Company were originally staked by Charles Auer in 1907, In 1910 when the level of the lake was exceptionally low, gold was discovered in a quartz vein near the shore and close to the present mine shaft.The mine is developed by a main shaft to a depth of 440 feet, with levels at 80, 180, 300, and 425 feet vertical depth and by a winze to 630 feet. A mill of 200 tons daily capacity was built during 1923, Production commenced on January 4, 1924, and continued without interruption to May 31; 1926, when operations were suspended due to a decrease in the grade of ore. Total production amounted to 27,416 ounces of gold from 99,708 tons of ore, an average grade of 0.275 oz. a ton. Diamond drilling and re-sampling of the mine during 1934 and 1935 indicated approximately 1,480,000 tons, having an average grade of 0.123 oz. gold a ton, above the 625-foot level."

Jan 1, 1954

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By L. S. Trenholme

"Belleterre Quebec Mines, Limited, is a subsidiary of Mcintyre Porcupine Mines, Limited. The property is in Guillet township, Quebec, 45 miles due east of Haileybury, Ontario. It is accessible by 72 miles of gravelled road from New Liskeard, Ontario (Fig. 1).Gold production at the property commenced in 1936 and to March 31st, 1945, had exceeded $9,000,000. For the past 3 years the milling rate has averaged 325 tons a day and the gold recovery about $14 a ton.GENERAL GEOLOGYThe rocks of the district consist of Keewatin-like volcanics conformably overlain by Timiskaming-like sediments. Together they form the remnant of an easterly plunging anticline engulfed by granite (Fig. 2). The pregranite intrusives consist of diorite, gabbro, and ultrabasic rocks, occurring as dykes, sills, and irregular stocks. Dykes of porphyry and lamprophyre presumably related to the batholithic intrusive are common in this area. The veins of quartz are also probably derived from the batholithic intrusives. A few dykes of Keweenawan-type diabase have been observed."

Jan 1, 1954

By Andrew D. Lapworth

The use of geological and grade models has been standard practice in mine design for many years now, with a wide range of software available to create and analyze the models. Although geotechnical parameters are also of vital importance for mine planning, there has been very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology based on digital photography for automated, safe and accurate 3D mapping of geological and geotechnical features in rock faces. Datamine has integrated this capability into its product range so that Sirovision becomes an integral part of day-to-day face mapping, mine geology and geological / geotechnical modeling in both open pit and underground mines. This results in improved fragmentation for loading, hauling and processing, and for open pits local geotechnical conditions can be taken into account to improve slope design and control. This paper describes some of the ways that geotechnical modeling can be used to create more refined and cost effective mine designs and then discusses the role of Sirovision in enabling the raw data required for such modeling to be collected quickly, safely and reliably.

May 1, 2007