Search Documents

By Y. C. Kim

This paper discusses Air Liquide's patented SPALTM (Surface Protection Air Liquide) technology and process for the inerting of coreless induction furnaces using cryogenic liquid gas. Air Liquide Canada Inc., in collaboration with Riverside Brass and Aluminum Foundry Limited (Riverside Brass), conducted plant trials to demonstrate the applicability of the SPALTM technology for copper-based alloys. Results showed that with SPALTM, Riverside Brass benefited from a significant increase in metal yield as the level of dross formation was drastically reduced. Together with the many other benefits of this technology, SPALTM demonstrated to be a non-negligible cost-effective solution to reduce metal production costs. In an effort to optimize the argon flow, different flow rates were used and the oxygen level above the metal bath was measured to pinpoint optimal flow. The results of metal yield, charge mix, dross formation, and melt temperature are compared with and without argon. The metal yield improvements are dramatic and calculated net savings are presented hereunder.

Jan 1, 2007

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By J. Goyman, K. R. Rawling

"1.1 Location and Transportation ServicesNanisivik Mines Ltd. is located at latitude 73°, 3,200 km north of Montreal and 700 km north of the Arctic circle, on the south side of Strathcona Sound, which is an arm of Admiralty Inlet, in Northern Baffin Island. The orebody and mill site are 4 km distant from Strathcona Sound which provides deep water anchorage for ocean transportation of concentrate to Europe during the short northern shipping season from mid-July to mid-October.The operations and the resident community have direct jet aircraft service from Montreal two days per week, and local nights connect with other Arctic communities in the northern Baffin region. Bulk supplies and general cargo are delivered in the summer shipping season.1.2 HistoryThe Texas Gulf Sulphur Company, now Kidd Creek Mines Limited, staked claims in the Nanisivik area in 1957 and carried out exploration through to 1968. After the Kidd Creek orebody was found, Texas Gulf optioned the property in 1972 to Mineral Resources International Inc. (MRI), which undertook further exploration and completed a feasibility study.Nanisivik Mines Ltd. was formed in 1975, with MRI as the majority shareholder and minority shareholdings held by Metallgesellschaft, Billiton and Texas Gulf. Strathcona Mineral Services Limited was retained to manage the project during both the construction and operational phases."

Jan 1, 1984

By R. Mariano

"The ability to optimise a concentrator from mill feed to final products requires a process simulator that integrates comminution, classification and separation stages. A key part of any such integrated process simulator is the inclusion of a model of mineral liberation in comminution to predict the particle composition distribution of the comminution products. This need was recognised by Gaudin (1939) who proposed a model of liberation based on the cubic fracture of a mineral texture composed of cubic grains of two minerals.This paper describes the development of a texture-based model of mineral liberation that builds on the method proposed by Gaudin. The approach described here, termed the JK-Gaudin Random Liberation model (JK-GRLM) uses as its basis the measured, volumetric mineral texture data that can be quantified for a given ore using X-ray micro-tomography. The textural data required as inputs for the JK-GRLM include the mineral grain size distribution. While the Gaudin model (in common with other existing liberation models) is a two-mineral (or two-phase) system, the JK-GRLM extends the approach to multimineral systems of up to 15 individual minerals, making it more widely applicable.An example of the application of the JK-GRLM to a base metal sulphide ore is provided. In the example the JK-GRLM is used to simulate the breakage of the measured ore texture and the particle composition distributions of the simulated progeny particles are compared to the measured particle composition distributions of ore that has been physically broken.The ability to calibrate this mineral liberation model with measured ore texture will allow it to be applied in greenfield situations where geometallurgical programs measure texture and in brownfield applications as a key part of integrated process simulations. The development of this model enhances our ability to simulate mineral processing operations as an integrated system."

Jan 1, 2016

By D. Bernard

Over the last decades, the wrought aluminum casting industry has made significant progress with regards to process consistency by the introduction of new technologies in the field of liquid metal processing and casting. These technologies, combined with the application of best practices, have led to increases in productivity as well as better process performances and product quality. The competition in the addedvalue aluminum products (by opposition to P1020 production) is, however, very strong and involves players that did not hold a major role five years ago but who are now exerting a strong competitive pressure on our industry even sometimes from far abroad. There are still technical and technological challenges remaining in the different areas of aluminum casting production, amongst which metal pre-treatment, furnace operations, in-line treatment and casting hold a predominant influence. The comprehension of the contribution of each individual process step to the entire process chain is a key element and must be considered in future process optimisations. This paper presents the technological position of the casting industry and tries to highlight areas where further progress can be made.

Jan 1, 2006

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019

By A. Tikhonov, D. Kipper, V. Korovin, A. Olifirenko, Yu. Shestak

The present paper deals with vanadium and molybdenum sorption from industrial wastes and intermediate processing products using Cybber macroporous strong- and weak-base anionites. Vanadium and molybdenum recovery by Cybber anion-exchange resins as well as desorption processes were studied in static and dynamic modes; their efficiency was demonstrated for that purpose. The results of the work may be used to design technologies for complex processing of both ores and industrial wastes containing vanadium and molybdenum.

Jan 1, 2011

By R. B. McIntosh, S Ramanchuk

A brief description is given of the process used by Sherritt Gordon Mines Limited to recover cobalt metal from nickel-cobalt sulphides. A description of the equipment with the operating conditions is presented with an evaluation of the corrosion test results for various stainless steels and other acid resistant materials for the part of the process involving the sulphuric acid leaching of nickel-cobalt sulphide slurry under air pressure. SINCE 1954 the Sherritt Gordon ammonia leach process has been used at Fort Saskatchewan to recover nickel metal, copper sulphides and cobalt-nickel sulphides from nickel concentrate produced at Lynn Lake, Manitoba. 'To develop a process for recovering cobalt and nickel from the cobalt-nickel sulphides, studies were carried out in the Sherritt Gordon laboratory and pilot plant and, late in 1957, continuous acid leaching of sulphides was started in the refinery. In September 1958 the present equipment

Jan 1, 1961

By K Byrne, W. Hawker

The average grade of copper concentrate is steadily declining, forcing the industry to turn to lower grade and metallurgically challenging orebodies. When faced with a low grade, challenging ore, mining companies are often forced to choose between high recovery at low grade or low recovery at high grade. Hydrometallurgical processing of copper concentrates using metathesis reactions, which replace iron with copper in copper-iron sulphide minerals and increase the copper to sulphur ratio in copper sulphide minerals, provide an opportunity to upgrade copper concentrates and potentially allow high copper recovery for a high grade concentrate. Factors such as concentrate mineralogy, reaction time and temperature, and the concentrations of copper, chloride and acid in solution are reported to affect the reaction extent and mineral phases formed by metathesis. In this paper, a copper concentrate has been studied over a wide range of conditions to investigate the influence of these key parameters on the extent of copper metathesis reactions and product phases formed. Solution and solid phases are assayed with the main mineral phases identified by Quantitative X-Ray Diffraction. INTRODUCTION The minerals present in copper deposits determine the prospective processing options either: pyrometallurgical or hydrometallurgical. For copper oxide ores, copper is typically present as oxides, carbonate, chlorides, silicates and sulphates. These minerals are readily solubilised in acid and are usually treated through hydrometallurgical processes. The typical process route for copper oxides is to leach copper into aqueous solution, purify and upgrade the solution phase through solvent extraction and then recover copper as metal by electrowinning (Davenport, King, Schlesinger, & Biswas, 2002). Copper sulphide deposits may contain a multitude of copper bearing minerals, including chalcopyrite, bornite, enargite, covellite, digenite and chalcocite. The copper ore grade and treatment options are affected by the mineral type and distribution. Sulphide ores are typically treated through comminution and mineral flotation to form concentrates, followed by pyrometallurgical smelting. Hydrometallurgy can also be used to process sulphides depending on the mineralogy and impurity levels (Davenport et al., 2002). The trend of decreasing copper grade with increasing impurity levels are common across the mining industry and pose future challenges to copper processing. This trend has prompted research into hydrometallurgical options for upgrading copper concentrates. One promising hydrometallurgical option is using metathesis reactions. Metathesis reactions, sometimes also called double replacement or displacement reactions, are chemical processes involving the exchange of bonds between two chemical compounds or species. In this case, the metathesis reactions involve copper in solution exchanging with cations in the solid sulphide concentrate. The driving force for copper sulphide metathesis is the relative affinity of the exchanging cation elements for sulphide. Based on sulphide precipitation diagrams, the expected order of affinity for sulphide should be Hg2+ > Ag+ > Cu+ > Cu2+ > Bi3+ > Cd2+ > Pb2+ > Sn2+ > Zn2+ > Co2+ > Ni2+ > Fe2+ > Mn2+ (Monhemius, 1977). Hence, copper metathesis reactions are capable of increasing copper content and removing impurities such as iron, nickel, zinc and lead from copper concentrates.

Jan 1, 2019

By A. K. Debnath

The water resource is key to survival of the mankind and this resource is now becoming critical in many parts of globe including India. As per an assessment of Central Ground Water Board (CGWB) of India, a huge shortfall of about 58 billion m3 of water is anticipated by the year 2050. In order to counter this shortfall, there is thrust from Government of India to adopt water conservation measures. National Environment Policy, 2006 of Government of India also stresses upon the need to take up water conservation measures for water security of the country. The coal mines in India provide an excellent opportunity to take up water conservations measures therein. The mine water is not acidic unlike western countries and it conforms to the prescribed regulatory standards. This nature?s gift is utilized in Coal India Limited by allowing mine voids to get filled with mine water. The net recharge potential of the opencast mining area is found to be about 5% in comparison to 2% in non-mining area offering good prospects for ground water recharge. The seasonal rainwater is also diverted into mine voids left at the end of mining operations which act as huge reservoirs/ pit lakes for storage of the water. They also serve as surface water bodies for recharging of water table in the surrounding areas. The area and space left from where coal has been extracted completely in underground mines and will not be entered by any man or machinery after the extraction, called goaf, are also potential source of water conservation. These additional water resources created are being utilized for meeting the industrial, domestic, irrigation and other requirements of the projects and local communities eliminating the need to tap other fresh water resources including ground water. Presently, 75% of the water demand of the coal mining project is being met from the water stored in the mine pits. In future, CIL is likely to create about 3.3 billion m3 of water resource, on an average, in its opencast mines alone. In the mine closure plan of opencast mines, the last cut is proposed to be developed into water body for recharge of ground water and creating additional water resources. A clean potential source of potable water is thus developed after mine closure. This will ensure water security of the country.

Aug 1, 2013

By L. Van Wyk, J. Fernandez, J. Suarez, L. J. Diaz, A. Uria, D. Breeuwer

"Ventilation is an essential component of any underground mine, playing a vital role in ensuring the health and safety of workers, and a mine’s continuous operation. At a time when mining companies are increasingly having to move to deeper underground operations in pursuit of high-grade ore-bodies, the search is on for more efficient ventilation systems that will allow mining to be carried out at even deeper levels whilst ensuring the protection of workers and the maximisation of productivity through temperature management and the lowering of energy costs. Mining companies today are looking for innovative ways to deliver new technologies and procedures to enhance their mine’s profitability. Energy consumption by mine ventilation systems is higher than ever due to stringent specifications of underground equipment (primarily combustion engine emissions), air quality standards and mining at deeper levels which all require more powerful ventilation systems. With energy costs associated with operating ventilation systems being a mine’s second-highest cost of production after labour, finding the optimal ventilation solution is critical to a mine’s performance. Proper fan design remains a major factor in reducing capital expenditures (CAPEX) and operational expenditures (OPEX), which means that there are compelling reasons for making use of comprehensive factory testing at full power before fans are dispatched to site to simulate the mine’s current and future design requirements, and thus verify the fan’s effectiveness in ‘real’ conditions.INTRODUCTION A primary mine fan is considered the heartbeat of the entire mine ventilation system, drawing fresh air from the surface and providing a safe environment for miners. A ventilation system’s lack of performance often leads to a reduction in acceptable air quality levels for underground working operations and can potentially have an adverse impact on production rates."

Jan 1, 2019

By S. Broda

Waste rock piles (WRP) are made of heterogeneous, coarse grained waste rock, with inclined layers due to segregation along the slopes and haul traffic compacted layers, creating highly contrasted hydrogeological conditions. The internal structure of the pile has a major impact on water and oxygen movement and pore water pressure distribution. In the presence of reactive minerals, this influences the production of acid mine drainage (AMD) or contaminated neutral drainage (CND) with metal leaching from the WRP. Water flow and distribution may also affect slope stability, particularly following major infiltration events (rain/snow melts).The prediction and interpretation of water distribution in WRP is a challenging problem. Numerous numerical investigations of short and long term forecasts have been conducted, and many of these were found of limited reliability. The shortcomings of existing approaches are typically due to difficulties in representing preferential flow processes in macropores. Such phenomena are in fact often neglected in the assessment of water flow in WRP because these are unattainable with the classical porous media approach typically used in this field. This paper focuses on the use of modeling techniques originally designed for massive fractured rock media to simulate flow in WRP. Waste rock properties used in this study are retrieved from large scale laboratory permeability and water retention tests and from in situ infiltration tests. The effect of WRP configurations on water flow into potentially reactive zones is examined with the numerical 3D fully-integrated surface/subsurface, variably saturated flow model HydroGeoSphere. Material properties retrieved from the laboratory tests are represented by means of stochastic facies distribution generated within a probability framework. Modelled soil water contents and hydraulic head distributions, as well as fluxes within a simple waste rock pile, with compacted layers, are compared with results retrieved from simulations based on the classical equivalent porous medium approach. Results indicate significantly increased flow towards the looser waste rock zone by considering heterogeneous material distribution, causing weak or absent capillary barriers and preferential flow paths. Practical implications for the design of waste rock piles are also discussed.

Aug 1, 2013

By M. Meratian

The in-situ methods have been developed in production of aluminum matrix composites. A commonly adopted in-situ method involves reaction between a metal oxide and aluminum to produce alumina particles or whisker reinforcements. Aluminum-alumina particle composite was fabricated by in-situ method where alumina particles were produced from reduction of copper and silicon oxides by melting and casting aluminum. Aluminum matrix composites reinforced by Copper and Silicon alloying elements and alumina particles have been obtained. The size and shape of alumina particles were studied by scanning electron microscopy (SEM). The size of alumina obtained from mixture of SiO2 and CuO was bigger than the alumina particles obtained from CuO.

Jan 1, 2007

By Laxman M. Amaratunga, Glen G. Hein

"Most mining operations utilize the tailings coarse fraction for backfilling while the fines have been traditionally disposed on surface in tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10-30% w/w of <45 µm) in the fill (Brummer and Moss, 1991). This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMO) from these ponds has proven to be a costly environmental problem and a long term liability.One practical method to reduce the environmental impacts associated with the tailings pond is to modify the physical and chemical prope1ties of the fine tailings so that they can be utilized in an environmentally safe manner. This was accomplished by agglomerating the tailings into pellets and using theses pellets as a coarse aggregate in a total tailings paste fill. This technology does not require any supplemental sand or gravel to be added to the fill.This paper presents the ongoing research into utilizing these tailings agglomerates as a coarse aggregate fraction, in order to create a total tailings paste fill which has supe1ior strength characteristics.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. The waste rock is usually returned underground for use as rock fill in underground support with the tailings remaining to be disposed of in tailings ponds. Tailings consist of a coarse and fine fraction, and can be either reactive (acid generating) or non-reactive. In an effort to minimize tailings disposal, the coarse fraction has been used underground in backfill along with alluvial sands. This diversion of the coarse fraction, however still requires that the fine fraction be disposed of in tailings ponds. This disposal creates the potential for acid mine drainage (AMO), since in the presence of air and water, reactive sulphide tailings can generate acid. It is therefore an important goal in the mining industry to minimize the disposal of fine tailings into tailings ponds since the treatment of AMO is a costly and long-te1m environmental liability."

Jan 1, 1997

By Edgar A. Manker

"Today&apos;s market for columbium has only developed in the last two decades, and in this sense it is ""newer"" than molybdenum, vanadium and most other steel alloying elements. In this short period, it has assumed a very important role in steel alloying and in superalloys. From a few hundred thousand pounds of columbium in 1960, consumption has grown to nearly 30 million pounds per year, with a market value approaching two hundred million dollars.To assess the outlook for columbium, we will first consider the historical development of consumption and supply, particularly noting that all of today&apos;s major mines were developed during the last two decades. From current production, we will attempt to reasonably project the future. This future may well include new producers, particularly some producing columbium as a co-product with tantalum.The growth of current applications, and emerging new applications, will be considered with regard to future consumption and in relation to future trends in pricing.IntroductionThe nineteenth century was a busy time for the discovery and naming of new elements. Among those discovered were columbium in 1801 and niobium in 1844. Although it was later shown that columbium and niobium are the same element, the two names are still used today. Niobium has been pronounced the ""official"" name by the International Union of Pure and Applied Chemistry, but columbium is still widely used in commercial practice, and we have chosen to use columbium in this paper."

Jan 1, 1981

By C. Cano

One of the main concerns within the mining industry is to minimize the impact of tailing facilities to the environment and nearby communities. Since the implementation of the first thickened tailings disposal (TTD) methodology at Kidd Creek in 1964, the thickened tailing disposal has been growing alternative disposal technology to mitigate the environmental impacts. Technical investigations on the TTD technology have been studied in detail to counteract the increasing shortage of water resources. One of the benefits observed with TTD is its resistance to potential earthquakes, particularly in zones with high seismic activity (Los Andes). TTD technology optimizes the maximum possible density for the material and generates a negative internal pore pressure in the material due to the surface and sub-surface water evaporation. This internal pore pressure should be enough to resist the pores pressure to which tailings are subject due to an earthquake action. The objective of this study is to verify the Shrinking Limit (SL) of thickened tailings during initial deposition and in the long term and the ability of tailings deposited by TTD would resist liquefaction. Fresh tailings coming from a flotation process of a copper plant concentrator were used. The samples put under cyclical three-dimensional tests associated with maximum credible earthquake magnitude range of 7.0 8.0 to develop a curve for the safety factor v/s depth for dry densities related to the maximum density obtained at the SL. At a dry density of 1.65 t/m3 liquefaction did not occur at any depth. At 90 % of dry density of 1.51 t/m3, liquefaction did not occur at earthquake magnitudes of 7.0 or 7.5 nor at any depth but liquefaction occurred at magnitude 8.0 between 0 m and 14.5 m; below 14.5 m, liquefaction does not occur.

Jan 1, 2007

The Mineral Industry of Canada in 1951 Continuance of the remarkable, successive increases in the value -of Canada&apos;s mineral production, chief basis of the nation&apos;s post-war expansion, was one of the highlights of Canadian development in 1951, when, according to the preliminary estimate is-sued by the Dominion Bureau of Statistics and reported in the BULLETIN for February, 1952, mineral output for the year reached a new high of $1,228 millions. This marked an increase of 17.5 percent over the previous year, which was the first in which the billion dollar mark had been reached, and an increase of 143.7 per cent over 1946, when production was valued at approximately $503 millions. While higher prices for the principal base metals accounted for a large part of the 1951 increase, quantity gains were made by copper, nickel, zinc, asbestos. lead, cement, and strikingly important. by petroleum, the value of which exceeded for the first time that of coal production. Gold was an exception to the general trend, being lower in both quantity and value than in 1950. For the first time nickel .came within $9 millions of surpassing-gold as the leading mineral product. Metals and Fuels The value of all metals, estimated at $733 millions, was 18.7 per cent more than in the previous year. Nickel advanced 11 per cent in volume and 34 per cent in value. Copper was up 2.4 per cent in quantity and 21 per cent in value, zinc rose 6.6 per cent in quantity and 35 per cent in value, and although the volume of lead produced was lower by 8 per cent, its value increased by 17 per cent. The tonnage of iron ore was 31 per cent higher than in 1950.

Jan 1, 1952

By T. H. Adair

"IntroductionCONTINUOUS casting of ferrous and non-ferrous metals is not a new innovation. Patents describing machines for continuous casting are on file as far back as the year 1842. In the middle of the last century, Sir Henry Bessemer conceived and built a continuous casting• machine for the production of mild steel sheet.The production of billets and slabs of both non-ferrous and ferrous metals is being carried out by the continuous method on a fairly large scale on this continent and abroad. At present, the volume of production of •copper and aluminum and their alloys in billet and slab form is much greater than the continuous casting of steel products. The new installation of a continuous casting unit at Atlas Steels, Limited, is designed primarily for the casting of alloy steel billets and slabs.As an introduction to the art of continuous .casting of metals, it is interesting to examine a few of the many devices which have been developed. As previously mentioned, Sir Henry Bessemer constructed a machine for the direct casting of mild steel sheet. His discoveries and ideas of continuously casting steel formed the foundation for the work of other pioneers in this field, all of whom have contributed to the improvement of this art through the ensuing years. The machines which will be selected for examination are those of Bessemer, Poland-Lindner, Williams, Ennor, and Junghans. The last unit to be discussed will be a modification of the Junghans machine recently installed at Atlas Steels."

Jan 1, 1954

By G. P. Cooper

A comprehensive computational heap leach model was used to evaluate options for operating a chalcocite-ore heap leach process. The stockpile leach model is based on the computational fluid dynamic software framework PHYSICA+ and incorporates various physical and chemical phenomena to simulate fluid transport, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. The leach model is calibrated against small-scale column leach tests, and simulation results are validated against closely controlled column pilot-scale tests. For a given set of ore conditions, the effects of raffinate irrigation rate are examined. Several options for pulse leaching were investigated, and the effects on copper recovery and pregnant leach solution (PLS) grade are described. Model simulations indicated that pulse leaching could be used to control copper grade of the PLS. Finally, an analysis of inventory issues is presented for various lift heights including multi-lift simulations to examine potential operating options. U sing irrigation rate, raffinate copper grade, and lift height as variables in a factorial design of experiments, the simulations showed that raffinate copper grade is the main factor that affects the soluble copper inventory grade.

Jan 1, 2007

By Kéiko H. Hattori, Neil T. Pettigrew

"Abstract- The Legris Lake Complex is a northeast-trending, 7.3 km long by 3.5 km wide, maficultramafic intrusive complex located in the western Wabigoon Subprovince of the Archean Superior Province. It is one of a series of mafic-ultramafic igneous complexes, the most notable of which is the Lac des Iles Complex, host to Canada’s only producing Pd mine with reserves of 93.5 Mt grading 1.53 g/t Pd as of December 2001 (North American Palladium Ltd., Annual Report 2001). Cu-Ni- PGE mineralization was first discovered in the Legris Lake Complex by a local prospector late in 1999. Shortly thereafter, the property was jointly optioned by Avalon Ventures Ltd. and Starcore Resources Ltd., who continue to discover significant Cu-Ni-PGE mineralization.One of the most notable features of the Legris Lake Complex is the occurrence of extensive brecciation caused by multiple injections of volatile-rich magma. The Cu-Ni-PGE mineralization is hosted by leucogabbro within a 2 km long by 600 m wide, highly brecciated area in the northwestern area of the Complex. The mineralized rocks contain disseminated to blebby sulfides (1 to 5 vol.%), comprising chalcopyrite + pyrite ± pyrrhotite + millerite ± pentlandite, typically surrounded by epidote. The majority of the Cu-Ni-PGE mineralization displays low ratios of Pt/Pd (~0.20) and high ratios of Cu/Ni (~2.9), which are similar to those of the Lac des Iles and the River Valley mafic-ultramafic complexes. The lithologies in Legris Lake Complex bear similarities to the heterolithic gabbro of the Twilight and Roby Zone deposits at the nearby Lac des Iles mine. However, the mineralization at Legris Lake, which is restricted to leucogabbro overlying unmineralized clinopyroxenite, is similar to that of stratiform deposits such as the Stillwater and Munni Munni complexes. The mineralization at Legris Lake is best explained by the late-stage, immiscible separation of a sulfide melt from volatile-rich parental magmas and the subsequent minor redistribution of metals by deuteric fluids."

Jan 1, 2001