Search Documents

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks

A combination shaft-electric furnace for the smelting of ores and the melting of metallized feed is being developed at the Mines Branch. When iron oxide pellets are smelted in this unit, they are preheated and partially reduced in the shaft before being transferred to the electric furnace where smelting is completed. Also, limestone flux added with the pellets is-preheated and calcined in the shaft. It has been demonstrated that, in smelting iron oxide in this unit, the throughput of the 250-kva electric furnace can be approximately doubled and the amount of electrical energy required can be very significantly reduced when the shaft furnace is operated in conjunction with the electric furnace. These benefits are achieved mainly by utilizing the sensible heat and latent energy contained in the arc furnace off-gases.

Jan 1, 1971

By J. R. Jutras, C. Brissette, J. Champagne

"Pure cadmium sulphide was leached by the action of the bacterium Thiobacillus thiooxidans in the presence of finely divided sulphur. The influence of time, temperature, pH and concentration of inoculum on the extent of the cadmium extraction was studied. Under optimum conditions, up to 72 per cent of the cadmium could be dissolved over a six-week period. A cursory study of the role played by elemental sulphur seems to indicate that its presence is essential but that the sul1>huric acid produced through its oxidation is a minor factor in the cadmium extraction."

Jan 1, 1971

By H. Link

"The extremely low permeability of the water-carrying beds in the nevonian formation of the potash district of Saskatchewan does not permit the injection of cement or chemicals to seal off sufficient water from the shafts to guarantee the safety of the mine. Based on many years of experience with wet shafts in the German and French potash mining industry, Alwinsal Potash of Canada Ltd. decided to have their potash mine shaft near Lanigan, Sask., which was completed in September of 1967, lined by means of an absolutely watertight lining of combined concrete and steel-plate construction.This shaft lining, consisting of two steel shells of welded construction with concrete filled in between, has proved itself before in the German coal mining industry. It guarantees a permanently dry shaft. With this type of lining, time-robbing and very often abortive injections are superfluous and the regular repair and adjusting work as well as the corrosion of conveyances and ropes can be avoided. Above all, however, the danger of a water inrush into the shaft is abolished completely."

Jan 1, 1971

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

By A. Sobering, G. N. Carlson

"This paper describes the conversion of the grinding section of the W a bush Mines pelletizing plant from conventional wet, open-circuit trunnion overflow ball milling, with filtering, and bentonite mixing on a common conveyor belt, to dry, open-circuit, grate discharge grinding, with pug mill mixing of bentonite and water at individual mills.The test work and data on operating economies to justify the cost of conversion are given. It is too early, at the time of writing, to have complete operating confirmation, but data are available. A brief description of the original plant is included."

Jan 1, 1971

By Hulbert A. Lee

"A REVIEW OF MINERAL DISCOVERIES IN CANADA, and in particular the Canadian Shield, using the physical aspects of overburden reveals a trend in the art of exploration. At an early time of exploration (1847-1954), float and heavy clasts were used successfully to find ore deposits with little knowledge of Quaternary environments. At a later time (1955 to present) , use of Quaternary rock-units for sampling have made possible tracing indicator trains of float, heavy clasts and other ore-type clasts to the source bedrock. The basal till of retreat ice is now recognized as a1l favourable sampling environment and as such has been used to successfully discover hidden orebodies. The esker massive gravel is beginning to be recognized as a favourable environment and use of it has met with technical success. An understanding of those changes that have taken place during the transportation of the material and after its deposition is essential to proper sampling and treatment of the samples from the basal till and the esker massive gravel. Use of float and heavy clasts in search of orebodies is continuing in present-day exploration on the Shield. Lessons learned from it are being incorporated into exploration using favourable Quaternary rock-units for sampling. Hence, both subjects have a need for review and are discussed in this paper."

Jan 1, 1971

By F. W. Tregarthen

"This paper gives a brief description of the methods used to form and implement the present planned maintenance program. The system is designed to assist plant personnel in their task of controlling a large work-force and maintaining the many and varied types of equipment used in a mining and concentrator operation. The types of reports and methods used in scheduling and work-loading are described. General built-in flexibility is derived from computer assistance to the Central Planning Group."

Jan 1, 1971

By J. D. Wilkins

"Ore outcrops were first discovered in the area in 1911. Following various periods of exploration by private interests and Cominco Limited, the Coast Copper Company, Limited property was brought into production in August 1962. Subsequently, Cominco explored the adjacent Quatsino Gold Mines property and is currently developing, and producing from, what is now known as the Benson Lake Mine.The Benson Lake Mine was developed using a conveyor-equipped decline and trackless LHD equipment. The operation produces 800 tons per day of copper-iron ore, copper being the main product. Copper and iron concentrates are trucked 25 miles to storage and shiploading facilities near Port McNeill to await shipment to Japan."

Jan 1, 1971

By D. A. Temple, G. O. John

Until recently, the approach to the problem of treating complex ores bas been to produce, insofar as is possible, mono-metal concentrates which are treated in traditional zinc, lead and copper smelting circuits, with the residues and by-products from some of these circuits being retreated for the recovery of contained values either by a separate residue treatment process or along with the primary feed to the appropriate circuit. The continued development of the Imperial Smelting Process, with its ability to treat poly-metal concentrates, calls for a re-examination of the traditional approach to this problem, and this the paper attempts to do. A survey of recent progress in the technical development of the process is made and a summary of current operational performance is included.

Jan 1, 1971

By R. W. Nice

"For many decades the incidence of a highly active graphite-like ore has plagued the McIntyre mine. This ore acts as a precipitant of the gold complex immediately upon formation of this complex. The gold is subsequently discharged with the tailings.Many different methods have been devised by various researchers all of which proved inapplicable for the McIntyre problem.Recently, McIntyre personnel, through their own research, developed a flowsheet. This circuit should give an overall recovery of 36% which is below the 94% experienced in the mill at present. Therefore, less revenue would arise from treatment of these ores. On the other hand there exists a possibility of more efficient mining methods in some of this ore thus allowing more economic recovery.INTRODUCTION This paper has been prepared to serve two purposes:i) To propose a method of recoverying gold from a sizeable orebody at the McIntyre mine at Schumacher.ii) To summarize and present the many methods suggested to solve a very old but very real mineral dressing problem familiar to the industry as long as cyanidation itself."

Jan 1, 1971

By C. F. Gleeson

"I HAVE BEEN ASSIGNED the pleasant task of adding a last word in way of summary to this session. I think that the trend set in having a geochemical session at the CIM Annual General Meeting is a good one and I hope it will continue so that members of the mining fraternity can get together on a regular basis and discuss geochemical problems peculiar to our Canadian scene. A series of interesting papers have been presented on what has been considered by many in the past as not only a problem area for geochemistry but even an impossible one. The papers should help dispel some of these fears. Lack of development of geochemical techniques in the Shield has been due to a variety of factors, many of which have been mentioned. However, I feel that one of the main reasons for this lack of development has been timidness on behalf of many people to get out and do the necessary work which helps produce answers to many of the questions asked. New developments and applications of geochemical methods in the Shield will not be done by the faint of heart but by those who have the curiosity, interest, imagination, drive, resources and, most of all, the intestinal fortitude to stick to it and not give up because results or conditions do not meet with preconceived notions. Another element that will be needed by those who will successfully apply the techniques and who will be responsible for new breakthroughs is the systematic approach to sampling and analysis and the integration of geochemical, geological and geophysical results. Erratic sampling patterns - a sample here and a sample there - generally lead to more problems than solutions."

Jan 1, 1971

By F. Mallozzi

"With the requirements of air pollution codes becoming more and more critical, the role of the ventilation engineer in industry has become an extremely important one. The ventilation engineer must provide the expertise for the selection of equipment and the design of systems which will reduce pollution to an acceptable level. Because pollution control systems involve considerable capital and operating expense, he must have the ability to select, from a wide range of products, the collector which will provide the required performance with a minimum of down time for maintenance. This paper discusses the principles of wet collection and the forces used to separate particulate matter from a gas stream. Important factors in the selection of equipment, such as collection efficiency, horsepower requirements and water consumption for the various types of collectors, are discussed in detail, as well as the construction features normally incorporated to circumvent potential problems."

Jan 1, 1971

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971

By John L. Bonus

"WITHIN THE BROAD PARAMETERS implied by the title of my speech, I propose to deal more particularly this evening with a subject the many aspects of which have constituted the essential elements of one of the main thrusts undertaken by the MAC in the past two years, i.e., to create among Canadians a much greater awareness of the importance of mining and to demonstrate to them what are the many and varied benefits they derive from mining activities across their country. In other words, MINING - WHAT IT MEANS TO CANADA.I also intend to discuss some aspects of government-industry relationships.I am very conscious of the fact that I am speaking to an audience made u in large part of experts in several fields of mining and exploration activities. They will be familiar with many of the points I intend to discuss. However, without in any way suggesting that familiarity breeds contempt, might I emphasize that even in this particular forum there is justification for reiterating some of our basic philosophies and suggesting ways whereby they might be better understood and promoted.Let us first summarize the present dimensions of the Canadian mining industry."

Jan 1, 1971

By M. E. Holter

"Three main potash members are recognized within the Prairie Evaporite Formation of Saskatchewan and have been designated, in ascending order, the Esterhazy, Belle Plaine and Patience Lake members. Each is composed of sylvinite near the geographic center of the member and becomes increasingly carnallitic marginally. Each stratigraphically higher member has a narrower carnallitic margin. The sharp contact between carnallitic and non-carnallitic components of the formation describes a surface which may be traced regionally and is not related to bed-ding. The contact rises higher in the stratigraphic section toward margins of members. Within each of the three members, analyses indicate that carnallite becomes more abundant toward the north whereas sylvite and insolubles, increase toward the south. Within each member, areas rich in carnallite are coincident with areas in which the member as a whole is thicker than averag,e. The Belle Plaine Member contains the highest concentrations of carnallite, the Esterhazy the lowest. A maximum content of about 30 per cent sylvite is common to all three members. Insoluble contents increase in successively higher members.Map studies are combined to outline the economic potential of the potash beds in terms of depth to the top of the Prairie Evaporite, ""salt-back"" thicknesses and sylvite grades for each member."

Jan 1, 1971

By J. A. Hansuld

"THIS SESSION marks something of a milestone in that it is, as far as I know, the first session at a CIM Annual Meeting devoted entirely to exploration geochemistry. This is an indication of the general acceptance and widespread recognition by industry of geochemistry in mineral exploration. As a first, I hope it proves sufficiently successful and interesting that geochemical exploration sessions will become a routine part of future CIM annual meetings. The greater use and acceptance of geochemistry has resulted in many investigations and advances, especially in areas such as the Canadian Shield. For a first session on geochemistry, the meeting in Quebec suggested an ideal opportunity to assess these advances and report on the current application of geochemistry in the Shield. The theme of the session is ""Geochemical Exploration in the Canadian Shield - The State of the Art."" A series of six papers will be presented dealing with the various dispersion media - rocks, heavy minerals, ""soils"", lake sediments, waters and vegetation. As a background to the individual presentations, I would like to take a few minutes to briefly trace the history of the use of geochemistry in the Canadian Shield."

Jan 1, 1971

By H. Tetu, F. Pells

"The copper-molybdenum property of Brenda Mines Limited is located in the Okanagan district of British Columbia, approximately 25 miles west of Kelowna. The Okanagan Valley is a resort and fruit-growing area, and therefore pollution control measures are more stringent than in some remote areas.The Brenda plant began production in April 1970 and is operated at a rate of 24,000 tons per day. The plant site is located at an elevation of 4,800 feet, which is approximately 3,600 feet above the level of Okanagan Lake. The site is in the Okanagan drainage basin.The major consideration in the design of the system was the prohibition of any downstream discharge. It was therefore necessary to redaim as much water as possible and to minimize the addition of fresh water to the system. The maintenance of a water balance is of critical importance.This paper will outline the major design criteria for the systems and the site investigations which were carried out. The design and construction of the facilities will be de-scribed and current operating experience will be outlined."

Jan 1, 1971