Search Documents

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By John N. Cunningham

Despite the wide use of micropiles for rehabilitating and retrofitting existing structures, little is known regarding the load-transfer distribution of grouted micropiles in various soil deposits. The rehabilitation of a concrete-frame warehouse in Portland, Oregon, required provisions for the seismic restraint of a new shear wall; the installation of two micropiles was specified to meet project requirements. The micropiles were uncased, 19-m (63-ft) long, 200-mm (8-in) nominal diameter, and reinforced full-length with a 64-mm (No. 20) diameter hardened steel threadbar. Due to space limitations, a sacrificial, instrumented micropile was installed near the two production piles to verify design assumptions. This paper describes the geologic setting of the project within the unsaturated Missoula Flood deposits, instrumentation, load-displacement behavior, load transfer, and Beta-coefficients for the sacrificial micropile.

Jan 1, 2011

By Pawan L. Sethi

Design and construction of deep foundations and basements is increasingly becoming more complex, as the density and frequency of urban development increases. This growth brings various associated challenges in the form of design considerations and construction challenges. This paper discusses some of the challenges routinely encountered as well as some specific complications in this area, based on author’s experience gained through exposure as specialist contractor (designer), consultant and specialist consultant, along with some information on how these challenges were overcome. The paper highlights some of the key aspects of design coordination and importance of having an awareness of the overall perspective. Examples will be used to illustrate practical problems and the approaches used to respond.

Nov 1, 2022

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005

By W. H. Liu

The stability of floors of large drydocks and wagon tipper sheds at coal terminals is an important matter but quite difficult to solve. Anchors can be used to join floors to foundations thus ensuring the stability of floors by the self-weight of floors and the pull of anchors. In this paper, the author describes the structures and types of the anchors used in the floors of the drydock in Beihai Shipyard and the wagon tipper shed at Shijiu Port, both in Shandong Province China, the determination of bearing capacity of anchors in rock bed of highly weathered granite, the comparison between prestressed anchors and non-prestressed anchors, the construction technology of anchors and the analysis of field experimental data.

Jan 1, 2010

By Mark X. Haley

Foundation design and construction in Boston has changed dramatically during the past 10 years. Prior to 1985, the primary foundation element in Boston, where deep foundations are required, was driven end-bearing piles. Since 1985, drilled or excavated high capacity foundation elements have been utilized more frequently. This paper will provide a historic perspective of their use and a summary of design parameters for elements installed and founded in the bedrock. TOPOGRAPHY Boston was founded in 1630 by the Massachusetts Bay Company of John Winthrop and his hearty band of Puritans. The settlement was chosen for: ? its safe harbor, ? abundant source of fresh water, and ? peninsula setting offering protection of the ocean on almost all sides with high ground for fortification. These three factors were a direct result of past geologic processes that created the Boston Basin by erosion of the soft bedrock underlying this area as compared to the harder granite rock to the north, west and south. As the glacial ice sheets melted and moved northward, various soil types were deposited. During ice sheet re-advancement the hills and islands of Boston took on their precolonial shapes. The Trimont, consisting of Beacon, Mt. Vernon and Pemberton Hill, rose to 150 ft above sea level with the smaller Copps and Fort Hill to the north and south.

Jan 1, 1994

By Maria Flessas, Justin Ray, Danielle Steinmetz, Brian Zuckerman

"The Ventura County Medical Center Hospital Replacement Wing project consists of the construction of a 2- to 3-story building with a basement encompassing the entire footprint and two corridors connecting the new hospital wing to existing buildings. The site is located in the Ventura Basin where strong ground shaking has been observed during moderate to large earthquakes on nearby faults. The upper 90 feet of the soil consists of loose to medium dense finegrained sands and low plasticity silts that are potentially susceptible to liquefaction, seismic densification, and hydroconsolidation. Ground settlement associated with a large seismic event on a nearby fault is estimated at 20 to 26 inches. To account for the anticipated ground settlement, auger pressure grouted (APG) piles gaining support below the potentially liquefiable soil were selected for the support of the proposed structure. Challenges for pile design included the anticipated earthquake-induced ground settlement, high downdrag loads, low soil lateral capacity during strong ground shaking, and the effect of pile installation on the performance of the existing adjacent buildings and the installed shoring system. The replacement hospital is supported on over 600 APG piles, with lengths varying between 120 and 140 feet. Axial pile capacities were verified with an extensive indicator pile installation program and dynamic pile load testing.INTRODUCTIONThe Hospital Replacement Wing (HRW) project is at the Ventura County Medical Center (VCMC) in Ventura County, Southern California (Figure 1). The VCMC consists of three interconnected hospital buildings (Buildings 303, 304, and Fainer Building), the Medical Laboratory/Cafeteria Building, two mental health buildings, a medical office building, an emergency generator building, and surface parking lots. The HRW is near the center of the campus, adjacent to several existing buildings.The HRW is a 2- to 3-story structure, with a 15- to 20-foot-deep basement beneath the entire 95,000-square-foot building footprint. The HRW project includes a Loading Dock, a four-level corridor to the Fainer Building (Fainer connector), and a two-level corridor to the Medical Laboratory/Cafeteria Building (Café connector). The corridors are structurally separated from the existing buildings. Typical dead plus live load column loads for the HRW range from about 635 kips to 935 kips and total loads range from about 860 kips to 1,295 kips."

Jan 1, 2016

By Lawrence P. Goldfarb

The City of Alexandria, Virginia, Public Safety Center (PSC) is a 64,000 square foot facility that houses the Police Department, Office of Sheriff and the Office of Magistrate. In addition, the center includes a detention facility for local and federal inmates, operated by the Sheriff. The PSC is composed of a 3-story building to the west and a 6-story building to the east constructed on a landfill in a wetland area in the flood plains of hunting Creek. The existing ground floor of the 3-story building is a floating slab-on-grade, with the interior and exterior columns, exterior walls and upper floors all supported on belled, drilled shafts. Portions of the floating first floor slab have undergone excessive settlement due to the apparent consolidation of the underlying organic soils. The magnitude of the settlements of the floating first floor slab is sufficient to require replacement of the slab and relocation of a portion of the facility. The rehabilitation was complex and required staged construction, consisting of constructing Auger Pressure Grouted (APG) Piles in low overhead conditions. This paper summarizes the geotechnical conditions that lead to the excessive settlement of the floor slab, the construction of the (APG) Pile foundations in low overhead conditions and the evaluation of potential future settlements.

Jan 1, 2009

By Anand J. Puppala

This paper provides information on various evaluation studies conducted to assess the CPT based interpretation methods. Salient findings from these evaluations are summarized. Additionally, a comprehensive evaluation study on both LCPC and European methods was performed on twenty-four driven piles selected from four different states. This evaluation showed that the LCPC method predictions are close to measured pile capacities. The European method provided good predictions for driven steel piles. Overall, both methods' predictions show high values of coefficients of variations, which are in agreement with other studies. Overestimation of driven concrete pile capacities is attributed to large estimations of unit point resistance. Suggestions to consider appropriate CPT based pile capacity interpretation methods are presented.

Jan 1, 2002

By Frederic Masse

With widespread acceptance in the market place, many engineers are choosing ground improvement techniques to provide suitable foundation subgrade at sites that would have traditionally required deep foundations. This paper discusses the Controlled Modulus Columns (CMC) ground improvement technique and some case histories highlighting the use of this technique for retail development sites. CMC are a sustainable and cost-effective ground improvement technology that transmit load from the foundation to a lower bearing stratum through a composite CMC/soil matrix. The CMC installation is also an attractive option from an environmental perspective because it utilizes reverse flight augers, which displace the soil laterally. This installation technique achieves two goals: it densifies the soil around the CMC, which improves load transfer into the element and avoids spoil and its disposal. Through the introduction of two cases histories, we will present the key benefits of the CMC technology. Each case history will clearly illustrate how a CMC solution can reduce the overall cost of a project when compared to a more traditional type of deep foundations. They will also show how the use of CMCs has benefits that relate to the overall sustainability of the project. While CMCs are an attractive financial and sustainable option, they have also demonstrated that the performance of the system is comparable to that of deep pile foundations. Because CMCs are a relatively new technology many potential users are not aware of its benefits. While we discuss the use of CMCs to support buildings in this paper, CMCs also have been used for a variety of other applications including foundations for tanks, mechanically stabilized earth (MSE) walls, and embankments

Jan 1, 2011

By Chris G. Leach

"Abstract A seven storey Northbridge area of Perth, Western Australia presented residential apartment complex located in the an opportunity for a novel application of Cutter Soil Mix technology (CSM). The development included a two-level basement for car parking which covered the full site area. However, the basement was also required to extend under an existing single story heritage building. Soil conditions comprised 2m of fill overlying medium dense to dense sands that in turn were overlying a very stiff clay stratum at approximately 14-16m depth. The ground water table was located at a depth of approximately 1m below the natural surface level.A site boundary consisting of a reinforced CSM retention system and was designed and installed to allow the excavation to proceed to basement level. Two rows of temporary soils anchors or inclined struts were required to achieve this. A CSM support system for the heritage building was also designed and constructed to provide temporary support during excavation and permanent construction works. The brief for the contract works emphasised that it was vital that settlements of the heritage building be kept within strict limits.CSM is a relatively new introduction to the Australian construction market, using a modified trench cutter to mix a binder slurry with in situ soils, generally to form cut-off walls, retaining walls and soil improvement works. This project is understood to be first application of the CSM for underpinning work in Australia.This paper discusses the site background details leading to the decision by the client to adopt CSM technology, and the design and construction aspects to meet the challenges offered by this project.Introduction190 Newcastle St is a 7-level residential apartment complex located in the Northbridge area of Perth, Western Australia. The development includes a 2 level basement for car parking, which covers the full site area. The basement also extends under a single story heritage building, which remained in-situ throughout the building works.A site boundary retention system was required to allow the excavation to basement level to proceed. In addition, a support system for the heritage building was required to provide temporary support during excavation and permanent construction works."

Jan 1, 2014

By Maurizio Siepi, Bruno Vingiani, Claudio Asioli

"The article describes an emergency rehabilitation intervention executed at Buyo Dam, in Ivory Coast, to intercept a significant water seepage occurring through the foundation of this zoned earthfill retaining structure constructed in the late Seventies. To solve the problem, a 800 mm thick, 400 m long impervious cut-off wall (COW) was constructed on the right side of the embankment, operating from the dam crest and with the reservoir almost at its maximum level. The use of an innovative pre-mixed self-hardening grout, with a target hydraulic conductivity coefficient (k) lower than 10-9 m/s, was considered the only way to match the tight working schedule and the strict requirements for the filling material of the COW.Presentation of the Hydroelectric Scheme of BuyoThe hydroelectric scheme of Buyo, located at 6°14’28” N 7°20’45 W on the Sassandra River, in Ivory Coast (Figure 1), was built in the late Seventies for agriculture and power generation. With a reservoir of 8.3 billion m3 and an installed power capacity of 165 MW, enough to supply electricity to 111,000 homes, it represents an installation of great significance for this West African country."

Jan 1, 2016

By Sylvia S. Eskander, Sherif S. AbdelSalam, Mona B. Anwar

Expanded Polystyrene (EPS) geofoam has long been used in numerous geotechnical applications due to its lightweight and durability. Among these applications is the use of EPS as an alternative fill material to conventional roadway soil embankments. This study investigates the benefits of using EPS roadway embankments to reduce the induced stresses and strains on the underlying peat and soft clay. Firstly, mechanical and interface properties of the EPS were acquired from a companion study that also considered the cyclic loading and creep effects. In order to determine the actual stress-strain distribution within the EPS blocks, a physical prototype was developed in this study with overall dimensions of 1.2 x 1.0 x 0.5 m, with a density of 35 kg/m3. The prototype EPS blocks were subjected to cyclic loading with intensities ranging from 10 to 50 kN. Then, a numerical model was developed to simulate the behavior of EPS roadway embankments. The numerical model outcomes were verified against the prototype measurements. A parametric design study was also conducted to develop a correlation between EPS embankment height and the stress-strain that occur in the underlying strata. Results showed that EPS embankments could reduce stress and settlement in the underlying soil by about 40% and 54%, respectively. EPS APPLICATIONS AND BACKGROUND Expanded Polystyrene (EPS) geofoam blocks have been effectively used during the past several decades in numerous geotechnical applications. EPS static and dynamic properties as well as interface behavior were extensively characterized in various published studies such as that conducted by Horvath, 1994; Stark et al., 2004; Zarnani and Bathurst, 2008; Trandafir et al., 2010; Athanasopoulos et al., 2012; AbdelSalam and Azzam, 2016; and others. However, to be able to use locally produced EPS blocks, its physical and mechanical properties must be thoroughly determined. The lightweight and compressible material of EPS geofoam makes it suitable both as a backfill and for absorbing pressure in both the vertical and horizontal directions. Kim et al. (2010) adopted EPS as an alternative for soil backfill around buried pipes; their model showed a reduction in the vertical stress acting on the pipes by up to 36%. Oshati et al. (2012) presented a case study of a field-instrumented box culvert with EPS blocks on top, which reduced vertical stress by 58%. Meguid et al. (2017) used an EPS inclusion to surround culverts and achieved up to 72% stress reduction, depending on the EPS density and the culvert depth to width ratio. AbdelSalam et al. (2017) used a relatively thin EPS inclusion behind flexible cantilever retaining walls, verifying that the lateral pressure can be significantly reduced by 25%; they also developed a design chart for this application. Moreover, AbdelSalam et al. (2019) investigated the use of EPS as a lightweight alternative for soil backfill above shallow tunnels. It was found that EPS had created a differential movement between the wedge located above the tunnel and the neighboring soils, which accordingly reduced the vertical stress acting on the tunnel by 85%, due to the use of lightweight EPS material and positive soil arching.

Jan 1, 2019

By Andrew Higgins, Jamey Rosen

This presentation will demonstrate some recent advancements in the applications of Project Information Systems (PIMS) technology to seepage barrier walls in the context of evolving Owner Specifications. The use of geospatial technology in particular is used to track, visualize, and analyze data from a variety of sources and serve those data to contractors and owners via dashboards and as-built drawings. Data describing the geometry of construction elements (including diaphragm panels, secant piles, and jet grout columns) is of particular importance on these projects, and this presentation will include case studies in the United States of how these data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage).

May 1, 2022

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By Peter de Kort

Tunnels in urban areas generally require deep excavations in soils under the groundwater table. In The Netherlands uplift loads are generally taken by piles installed into dense sand layers, which are hard to penetrate. To avoid nuisance and damage to the environment, piles often need to be installed using vibration free methods, which also have the advantage of low noise levels during installation. Drilling piles and obtaining a high uplift resistance is a contradiction in itself. Franki has adopted several installation methods based on the injection of grout during drilling and/or post grouting to overcome the difficulty of hard layers. This report presents two projects, situated in Rotterdam and Sneek, where vertical tension piles in floors, subject to high uplift loads, have been used. It also explores a project in Zeebrugge (Belgium), where tension piles are installed at an inclination of 1:1 to anchor a diaphragm wall for a quay construction. Test results presented in this report show, that vibration free and soil displacing piles can be installed in very dense sand layers and that a high uplift resistance can be achieved. It is also shown, that a variety of installation methods is available, even in limited space.

Jan 1, 2008

By W. Morgan NeSmith

A drilled displacement pile program was utilized for the expansion of an existing power plant in Cohasset MN adjacent to the Mississippi River. The drilled displacement (DD) pile is an innovative foundation type that provides exceptional value in some geologies. In the U.S., DD piles have typically been used in coarse-grained soils due to the large friction capacities that can be generated by the piles in these conditions. This project was the first large scale experience for the project team where it was anticipated that significant portions of the DD pile capacity would be developed in primarily fine-grained soils. The project site consisted primarily of variable amounts of fill overlying predominantly low plasticity alluvial silts. In some cases, alluvial silty sand layers were encountered within the expected pile installation depths. Alluvial sands were typically encountered below the silts, in some cases within the expected pile installation depths. The project team developed a probe and pile load test program to address the variable subsurface conditions across the site. The program included monitoring various parameters (including applied torque and tool penetration rate) during the drilling portion of the pile installation using recently developed data acquisition techniques. This data was used to estimate the rig energy, or Installation Effort (IE), required for pile installation. IE profiles from the test and indicator piles were compared with subsurface data available from a number of previous site characterizations. Additionally, Cumulative IE values were compared to an in-house database of IE vs. DD Pile Capacity. Final production pile toe levels were based primarily on IE values selected from this comparison. The IE data collected during production was also used to address large variations in pile-cutoff elevation (relative to a fairly uniform ground surface elevation).

Jan 1, 2008

By Scott D. Neely, Donald R. Clark

"An existing landslide located at the southeast corner of the Telluride Regional Airport has been in an active state of failure for several years. The presence of the landslide has represented an on-going liability for the Airport, the Federal Aviation Administration and the Colorado Department of Transportation. A catastrophic failure of this landslide occurring in a manner similar to that which occurred at the Airport in 1987 has posed an on-going threat to closing Colorado State Highway 145 south and below the slide area. The existing landslide has been characterized as a series of multiple failed block areas located downhill of the airport runway that have occurred in severely weathered Mancos Shale.A total of 12 alternatives were evaluated to mitigate the landslide, including the preferred alternatives of either partial or total landslide removal. However, prior development has left essentially no place on the airport property that would allow for the disposal of the landslide debris for either the total or partial removal alternatives, and the closest off-site disposal area was approximately 40 miles from the site. As a result, in-situ stabilization of the landslide, including a primary system of isolated tie-back anchor plates with strand anchors, and a secondary system of high strength steel mesh and intermediate anchors was selected for the ultimate design of the project to stabilize the landslide in place.For design purposes, geotechnical characterization of the slide area was accomplished through geological mapping, conventional borehole exploration and geophysics using multiple electrical resistivity. The paper discusses the design process utilized and the unique challenges faced one-third of the way through construction when discovery of a survey error required redesign of the entire landslide mass stabilization system using the prefabricated anchors that had already been delivered to the project.INTRODUCTIONTelluride Colorado is located at the toe of the Colorado Rocky Mountains on the western slope. The Telluride Regional Airport is located on Deep Creek Mesa about 5 miles west of the town of Telluride.The landslide is located at the southeast corner of the airport just below an abandoned portion of the quarry access road on a south facing slope. The quarry access road is located below the elevation of the runway and outside the elk fence that surrounds the air traffic area of the airport property. Since the reconstruction of the runway, the access road to the quarry and the construction access road for the reconstruction of the airport runway and safety area were rerouted to stable ground north of the previous access road location and off of the head scarp of the landslide."

Jan 1, 2015