Search Documents

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006

By H. Mori

This paper describes a new borehole loading test using a self-boring instrument appropriate for dense sandy soils and stiff clayey soils. The results of loading tests for the bearing strata of deep foundations according to this method are also presented. This method has been applied to the study on the settlement behavior of heavy foundations resting on dense sand, stiff clay or soft rock in Japan.

Jan 1, 2010

By John P. Briand III, Douglas J. Aghjayan, Robert E. Fosse

This paper highlights the successful pile load testing program for the redevelopment of Pier One in East Boston, Massachusetts. Pier One is a 5.4-acre parcel on a dormant waterfront site used in the 1950s as a warehouse and distribution facility. The developer plans to re-use the existing 14-inch-diameter concrete-filled steel pipe piles to support four 5- to 7-story apartment buildings above a 2-story parking garage. A pile load testing program was developed to establish if the existing piles could support design loads of 240 kips for project financial feasibility and up to 300 kips for a significant reduction in future foundation costs. The Phase 1 program consisted of statnamic and dynamic load testing on two piles with two loading intervals (200 and 240 kips). Based upon the favorable results of the Phase 1 program, the Phase 2 program involved statnamic load testing on two piles and dynamic load testing on ten piles with three loading intervals (200, 240, and 300 kips). The Phase 2 program confirmed the favorable results which were applied across varying strata thicknesses and pile embedment depths. The average allowable capacity for the piles tested was greater than 300 kips with pile movement up to 0.3 inches.

By Andrew Middleton, Mark Wyatt

"The Brickworks Marketplace Project is a significant shopping centre development in inner north west Adelaide constructed by Badge Constructions in 2014 and 2015. The site was a former brickworks with a deep pit containing various extents of uncontrolled fill which was to remain on site, and with a remaining void up to 6 m in depth. The existing uncontrolled fill was improved using the High Energy Impact Compaction system, and the pit backfilled using a quarry crusher byproduct selected by trial and a recycled crushed concrete and bricks and compacted in deep lifts. This approach resulted in significant savings in compaction time, cost and building foundations. The settlements of various parts of the completed works have been monitored since February 2015 and this monitoring has demonstrated small settlements which meet the user’s constraints.INTRODUCTIONThe Torrensville Brickwork Markets project involved the transformation of a former brickworks and clay pit site into a regional 17,000m2 shopping centre, opening in June 2015.The site was a former brickworks with adjoining clay borrow pit. The clay pit had been partially backfilled over many years with ‘uncontrolled’ fill comprising ‘clean’ soil, bricks and kiln dust typically of the following thicknesses:??of the order of up to 7 m to 10 m but locally up to 15 m in the western part of the site??2 m to 5 m in the south-eastern part of the site; and??less than 0.5 m in the north-eastern part of the siteAnecdotal reports suggested compaction of some of the fill may have been undertaken, although this not able to be confirmed nor records obtained.Initially it was proposed to take up the existing uncontrolled fill, sort and recompact or remove to landfill, followed by backfilling in conventional means over 500,000 cubic metres of imported filling to a thickness of up to approximately 6m to backfill the former pit. This work represented a significant cost and was not economically viable.During early negotiations, the contractor proposed an alternative to retain and ground improve the existing filling on site, and to backfill the pit with fill placed and compacted in deep lifts, thereby significantly improving the economics, environmental and community impacts of the proposed works.The developer agreed to the proposal with the following performance criteria:??a settlement of =10 mm after 10 passes by the Impact Compactor (on existing subgrade areas);??a bearing capacity of 250 kPa for high level footings;??a maximum long term differential settlement of 40 mm (measured over 16 m), ie. 1 in 400; and??a minimum modulus of 40MPa."

Jan 1, 1900

By Walter Kaeck

In a recent upgrade of their system, Amtrak converted a bascule type draw bridge over the Thames River to a vertical lift structure supported by the existing piers. During the bridge replacement, significant settlement occurred on one of the piers and movement continued thereafter. Construction was stopped as Amtrak became concerned as to how much the subsequent construction activities would cause the pier to further settle and tilt, not only impacting the operation of the existing bridge, but also jeopardizing the new lift span. Mueser Rutledge was engaged at this time to help understand and solve the problem. A remedial grouting program was developed to arrest the settlement. As a subcontractor to Cianbro Corporation, Pittsfield, ME, The Judy Company was hired to perform the remedial grouting work. Work platforms were constructed around the pier for support of the drilling equipment. A dual string drilling system was used to install sleeve pipes at depths of up to 185? below the water level. Ultrafine cement grout stabilized with additives was placed at 2.5 foot intervals through the depth of the sand and gravel stratum below the bottom of the pier. Logistics were difficult and the schedule was severely impacted by the remedial work, necessitating working six 12-hour shifts per week and working in the river through the winter months. After four months of drilling and grouting, movement of the pier stopped. At the conclusion of the remedial work, more than a million gallons of ultrafine cement grout were placed. Confirmation borings recovered completely solidified material with compressive strengths ranging from 500 to 1500 psi. The bridge replacement was then completed and is functioning. Continued monitoring through July 2009 shows negligible movement.

Jan 1, 2009

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By Fredrik Sarvell, Harald. Ihler, Veli-Matti Uotinen, Jukka Rantala

"Many of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The ultimate structural load bearing capacity of a pile in a cohesive soil is decided by examining which gives the lowest value, the peak buckling load and the resisting moment provided by the surrounding soil medium or the structural capacity of the pile cross section. In both cases, the initial deflection of the pile is a significant factor when the axial load bearing capacity of the pile is determined. Steel micropiles are joined commonly with mechanical splices. A less rigid mechanical splice is often a weaker hinge that allows the pile to bend and deflect more during installation increasing the initial deflection of a pile. In addition the less rigid splice element decreases the bending capacity of a jointed pile section and the ultimate axial load capacity of the entire pile. A series of FE analysis performed for various pile sizes suggest that the steel pipe piles including separate pile sections and mechanical splicing elements should have the combined bending stiffness of EIshaft = 0,75 × EIpile. This requirement yields to the buckling resistance of at least 96 % of the solid reference pile with the sameinitial eccentricity in similar soil conditions.IntroductionMany of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The potential buckling of these very slender high capacity piles in soft soils may in many cases be the controlling design factor of the pile, especially with end bearing micropiles.A typical sequence of soil strata in Nordic countries, such as Norway, Finland and Sweden, constitutes of friction soil or dry crust clay on top of soft clay followed by till. This soil stratum often rests on solid bedrock of granite or gneiss. Conditions like these are suitable for slender end bearing piles subjected to buckling and especially steel pipe piles where most of the material is located at the edge of the cross section. Other reasons for using slender steel pipe piles are for example fast installation with minimal waste, efficient manufacturing and relatively well established design and execution procedures. Minimum quality criteria’s regarding splices for steel pipe piles are recommended to be set as national provisions to ensure quality and comparable procurements in foundation business."

Jan 1, 2014

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By Brian Koch

Michels installed 242 drilled shafts to support the piers for a new basket-handle, true-arch twin bridge across the Mississippi River from Moline, IL to Bettendorf, IA. The installation of the drilled shafts was completed with the simultaneous use of two Liebherr LB36 and one IMT 300 drill rigs. Utilizing barges, 233 drilled shafts were installed in the river. Michels crews also installed 7-ft to 10-ft permanent steel casing into the bedrock, and drilled to depths of 60 feet for each shaft. Despite working in strong currents, freezing temperatures and on rocking barges, Michels crews placed the shafts within 3 inches of plan position. Since the drilled shafts are the key piece in supporting the bridge structure, Michels provided cross-hole sonic logging to verify the integrity and strength of the concrete within the shafts and to add another level of quality control for the owner/customer. Extensive planning took place each day to ensure that tugboats, the linchpin of the project, were being efficiently utilized to shift the barges and materials daily. On any given day, Michels transported five concrete trucks by barge from shore to shaft sites to pour between 40 and 240 cubic yards of concrete. The Michels environmental team was diligent with preparing, discussing and implementing a water treatment plan that was accepted by all state and federal agencies and adhered to strict environmental regulations. Grain hopper barges were rented to control and treat the water that was used in the drilling operations. Another challenge crews ran into was the discovery of caverns when drilling into some parts of the bedrock. Michels worked with the engineer to develop a plan to construct the drilled shafts that encountered the caverns.

Jan 1, 2019

By Marco D. Boscardin

Control and mitigation of building response to construction activities are assuming a greater role in design decisions for underground construction. Alternatives for controlling building response have multiplied with the continued development of ground modification methods, better control of construction activities that cause ground movements, and increased understanding of building behavior and response. This paper describes approaches to estimating building response to construction-related ground displacements caused by adjacent excavation and highlights the discussion with several case history examples. Examples discussed includes experiences with two, seven-story historic structures, supported by timber piles with granite block pile caps, which were underpinned in preparation for ground-freezing ground stabilization and tunnel construction beneath the buildings. The elevation of each building column was monitored and elevation adjustments were actively performed during construction. The second example examines the performance of a slurry wall braced cut, 45 to 50 feet deep penetrating through a stiff crust into a soft clay layer and associated building response. This cut was immediately adjacent to two, approximately 15-story office buildings, which were supported by deep foundations founded in the stiff crust.

Jan 1, 2003

By Manchanda H, Agarwal J.

The construction industry has one of the largest numbers of injuries compared to other industries. Thus, reducing accidents and determining construction risks are extremely important. One of the essential steps for construction safety management is hazard identification and risk assessment, since the most unmanageable risks are from unidentified hazards. While the urban rail transit systems are being developed rapidly in almost all major cities of India, adjoining Existing Building Structures and historic sites are facing possible threats of unexpected damages and accidents. The protection of these structures becomes one of the major challenges specifically when the infrastructure being developed involves construction of underground tunnels passing through old cities. The assessment of settlement induced damage on buildings during the preliminary phase of tunnel excavation projects, is nowadays receiving greater attention. Analyses at different levels of detail are performed on the surface building in proximity to the tunnel, to evaluate the risk of structural damage and the need of mitigation measures. The current paper presents current practices being adopted in India for prediction and excavation of tunnelling induced ground movement and building damage risk-assessment. The paper highlights empirical and numerical approaches towards predicting settlement induced damages on buildings during the tunnelling, detailed step by step methodologies for conducting building condition surveys, evaluating associated hazards, and adopting adequate building risk identification and mitigation methods. The paper also discusses associated technical and contractual challenges and highlights way forward to overcome them.

Sep 1, 2022

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

By Jason N. Scott

CFA piling is a ?blind? construction process that relies heavily on the rig instrumentation to produce sound piles. If the data measured and recorded during construction can be made available to engineers and managers within hours after construction then there are many economic and quality control benefits that can be realised. A state of the art CFA instrumentation and data management process has been developed in the UK. The key components of the instrumentation, GSM data service and the central database are described. Many benefits to the business have been realised and, where possible, these are quantified.

Jan 1, 2006