Search Documents

By D. Z. Wei

Amine collectors with different structures and length of carbon-chain have been widely used in oxide minerals flotation. In this paper, we synthesized one kind of binary amine, N-dodecylethyl- enediamine, and studied its flotation performance. From the results, we can see N-dodecylethylenediamine which has excellent frothability, is a new type of chelating surfactants. And it also has fine catchability to quartz and hematite. The recoveries of quartz and hematite increase with the augment of N-dodecylethylenediamine concentration. When the dosage of collector reaches 100g/t, the recoveries of quartz and hematite achieve 95.30% and 87.89% respectively. Meanwhile, the influence of pH on the flotation recovery of hematite is studied and test results showed that, as pH increases, the flotation recovery rises until pH=9. And the recovery reaches its maximum in alkalescence. The collector has better flotation capability to quartz than to hematite. And the maximum recovery of quartz is gained in alkaline media, which reaches 97.87%. Finally, the flotation mechanism of N-dodecylethylenediamine is discussed through the measurement of infrared spectroscopy.

Jan 1, 2014

By F. Z. Dong

The paper is mainly about a study on the techniques of separating iron from pyrite cinder of a certain sulfuric acid plant in Shandong province. The main components of the cinder are Fe2O3 and SiO2, and the degree of liberation of iron mineral and gangue is very high. So the iron concentrate with higher degree of iron and lower grade of silicon and sulfur can be achieved by reverse flotation. The iron grade of the concentrate reaches 63% and the recovery of iron is no less than 63%. And the most important influencing factor of the flotation is the temperature of the pulp. A better guideline can be achieved by magnetic separation. The cinder is magnetizing roasted for 15 minutes with temperature of 800?, and the concentrate with the iron grade 64%, sulfur grade 0.2% and iron recovery 85% can be obtained by two stage magnetic separation. A rotary kiln has been built to deal with the pyrite cinder, and the result of the industrial magnetizing experiment and magnetic separation is satisfying.

Jan 1, 2014

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By Jia Muxin

The adsorption behaviors of metal ions on a silicate mineral and the flotability of a metalized silicate mineral with sodium oleate as collector are closely related to the structure of the silicate mineral. The adsorption isothermals of the metal ions on different silicate minerals are studied, the parameters of the isothermal give the information how many surface oxygen anions a metal ions is attached to, from this information and the structure of the mineral the site where a metal ion is attached can be guessed (The adsorption isothermals and adsorption behaviors with pH are fitted with Temkin, Frenudlich and Kurbatov equations respectively). Metal ions as Cu2+, Ni2+, Zn2+ are attached to the oxygen anions of surface species –Si-O– on the quartz surface, most of them coordinate to only one surface oxygen, their adsorption ability on quartz is low, but this metal ions on quartz surface protrude out of the surface perfectly, so their ability to combine with oleate acid radical is excellent. Quartz can be activated well by such metal ions. The isothermal of Fe3+ on quartz indicates these cations coordinates with more than two surface oxygen anions. This means the Fe3+ nucleates on quartz surface in the form of Fe(OH)3 colloid particles. The isothermals of Cu2+, Ni2+, Zn2+ Fe3+ on spodumene shows such ions coordinate with more than two surface oxygen anions, it indicate these ions may attach to the position where Li+ is formerly exists, such metal ions stay in a cave on the mineral surface, their adsorption abilities on spodumene are quite well, but they are affect by the oxygen anions of the two Si tetrahedron chains, the can almost not activate this mineral. These cations may attach on the site where Al3+ exists on the muscovite surface, just like spodumene, muscovite can not be activated well by such cations. Pt2+ has a large ion radius, as Pauling’s rules depicts polyhedron can not attach to Si tetrahedron well, the adsorption ability of Pt2+ on quartz is low and quartz is activated badly by Pt2+. On the other Pt2+ can adsorb well on spodumene and muscovite well and activated them well because it is not affected so bad by the tetrahedron oxygen anions of the minerals for their its large radius. The isothermal of Ca2+ on quartz indicates a Ca2+ coordinates with less than one surface oxygen anion, this means Ca2+ attaches on quartz mainly by physical adsorption. The adsorption abilities on mineral surface and the interaction abilities with oleate acid radical of the transition metal ions with the same valence are guessed to be determined by their d electron number, the rules should be d1<d2<d3<d4>d5<d6<d7<d8<d9>d10. Hydrogen bond may play an important rule in the activation of the mineral by HF and the interaction of the HF activated silicate mineral with collectors. The general rule is high bond valence and small metal ion radius surface species –Me-O can be activated well by HF with sodium oleate as collector. For example – SiIV-OH is neutral while –SiIV-FH+ and –SiVI-FH+0.33 are positively charged, the positively charged surface species are more likely to connect oleate acid radical via hydrogen bonds.

Jan 1, 2003

By Q. J. Liu

The flotation circuit and the reagents of the all-sliming flotation about low grade and hard operation on zinc oxide ore are researched in the paper. The results indicated that there are many types of zinc minerals in this ore, and the composition is very complex. They include hemimorphite, smithsonite, hydrozincite and so on. The ore is seriously sliming. In light of the ore properties, three kinds of flowsheets have tested. They are gravity concentration (cleaning tables), flotation, combined process of gravity concentration and flotation. The test showed that the recovery of zinc is only 17.08% in the gravity separation. In combined process of gravity separation and flotation, the recovery of zinc concentrate is close to 70%. But the flow-sheet is complex and hard to control in the production. The floatation circuit is feasible. In the test, it pay attention to investigate the new combined reagent which is used in selective all?sliming flotation process. The effects of slime are eliminated by the multi-loop treatment of middling. In flotation, the final recovery of concentrate is 88.76%; the grade is 29.50%. The recovery of physical ore is 93%; and the recovery of -10mm fraction is more than 65%.

Jan 1, 2014

Reverse flotation process tests were conducted for marine sedimentary silicon-calcium phosphate ore in this research. The research findings showed that by adding antifoamer, a concentrate with P2O5 32.36%, SiO2 10.69%, MgO 0.67% was obtained, with recovery of P2O5 being 88.12%. Such is a satisfying result, when compared with the original mineralogical component of P2O5 26.64%, SiO2 11.51% and MgO 3.36%. When using antifoamer, the SiO2 grade of the concentrate increased 0.55%, the MgO grade decreased 0.64%, while P2O5 recovery increased 2.69% compared by adding no antifoamer. Adding antifoamer is favorable to increase the grade and recovery of P2O5. Therefore, antifoamer is necessary. Tests of synergistic reaction of antifomer indicate that the appropriate consumption of the antifoamer is 275g/t CY and 1Kg/t TWF. Keywords: silicon-calcium phosphate ore, desilication, antifoamer, reverse flotation

Sep 1, 2012

By Zhou Junwu, Sun Chuanyao, Wang Fuli

"In this present paper, the authors introduce the artificial neural networks into the modeling of the industrial flotation process, integrating information technology, control theory and intelligent optimizing method to flotation technology. The new idea gives a new way to solve the difficulty in this field, and therefore brings the study on the automatic control of flotation process in China into a new start.The Radial Basis Function (RBF) network, featuring a quick learning speed, is one of the feedforward neural networks. It has attracted much attention from automatic control recently for its implementing the nonlinearity mapping through adjusting the parameters of the nonlinearity transfer function. One of the online adaptive learning algorithm—the nearest neighbor-clustering algorithm, which can automatically determine the number of hidden units, has been implemented in the MATLAB programming language in this paper, laying the foundation for the flotation models.The relation model between ore pulp characteristics and reagents consumption has been proposed using the RBF networks based on the industrial lead rougher flotation of lead & zinc ore, and the simulation has been conducted in the laboratory with the results matching the samples data very well. The Xilin Lead & Zinc Mine Flotation Process Intelligent Consultation System of Reagents Consumption, which suitable for industrial process, has been developed. The reagents consumption advised by this system would stabilize the flotation process, and increase the recoveries. It could be used for providing the technological consultation to flotation operators in site, and for training new operators."

Jan 1, 2003

By F. S. Niu

With the feature of finely-dissemination particle and complex mineral composition, oolitic hematite is considered to be the ore dressing difficult problem in the world. Series research on refractory oolitic hematite in Zhangjiakou Area are introduced as following: ore properties?technology mineralogy and mineral processing technology. The survey shows: with the fine grinding of the hematite to a fineness of -0.076mm 95%, obtaining iron concentrates grading 62.74% Fe at the recovery of 46.80% by high intensity magnetic separation- reverse flotation flowsheet; under the three stages intensity magnetic separation,four stages grinding and four stages gravity separation, getting the iron concentrates grading 61.09% Fe at the recovery of 45% using high intensity magnetic separation- gravity separation flowsheet; with roasting temperature of 800°C, time for 75~90min and ore-coal ratio of 11, gaining the iron concentrates assaying 62.74% Fe at the recovery of 87% by roasting- magnetic separation flowsheet. At present, this research is still doing for the target of raising the concentration recovery on the base of high grade concentrate. It is in the hope of fully utilizing the existing hematite resources in Zhangjiakou

Jan 1, 2014

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By Ye Junjian

The feed ore is the concentrate of low intensity magnetic separation of pyrite tailings, containing TFe47.47%, S19.41% and SiOpyrrhotite. The exploratory tests showed that using a process of flotation followed by magnetic separation could respectively obtain a sulphur concentrate of S 31.08% with a recovery of 82.89%, and an iron concentrate of TFe 59.97% and S 9.52%with a recovery of 30.93%. The reason of iron concentrates with high sulphur grade was that the sulphur grade of flotation tailings was 7.03%. So enhanced flotation for pyrrhotite was investigated in this research. Results show that when the natural pH of ore pulp varied from 5.5 to 6.0, a reagent combination of FS, LH, and BJ displayed the optimum flotation performance for pyrrhotite. After comparisons made on different flotation processing, the previous flotation flow of ?one roughing, one cleaning, one scavenging system and middling reprocessing?, was found, among others, to have the best flotation effect, as the grade and recovery of sulphur concentrate were 31.08% and 82.89%, respectively, and sulphur content of the flotation tailings was 7.03%. The above results indicated it was difficult to raise further the effect of flotation desulphurization. The authors therefore suggested that oxidizing roast should be adopted following the magnetic process for the purpose of further desulphurization. Besides, flue gas containing SO2 8.25%. And the valuable minerals are magnetite and 2 generated from roasting could be reused for sulphuric acid production. Keywords: pyrrhotite, enhanced flotation, desulphurization

Sep 1, 2012

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Y. H. Hu, X. X. Zhang, Z. F. Dai, H. J. Huang, Q. S. Huang

"In order to get a more comprehensive understanding of the interaction of fine fluorite particles and bubbles, the electro-flotation was conducted, a high speed CCD was used to determine the bubble size distribution, and the results were analyzed using the models of collision and attachment. The electro-flotation was performed in a modified Hallimond tube. The results show that for different fluorite with size of 0 -10µm, 10 -38µm, 38-74um, there is a matching range between the different particle sizes and cathode aperture size (38um, 38um, 74um) to reach highest recovery. In addition, improving the concentration of collector is benefit for the flotation recovery due to the ability of collector to decrease the bubble size and prevent the merger of bubbles. Furthermore, theoretical calculation of collision, adhesion probability and collection probability is in agreement with the experimental data for electro-flotation recovery of fluorite.INTRODUCTIONFluorite is widely distributed, and has been found in more than 40 countries around the world. As fluorite minerals are easy to float, flotation is used as the best method of the current recovery of fluorite (Yang and Ai, 2016; Chen et al., 2017). In the field of mineral processing, the flotation of fine particles is particularly difficult, caused by the small quality and large surface (Sun et al., 2006). Flotation is now considered to contain three subprocesses, including the collision, attachment and detachment between the particles and bubbles (Sun et al., 2011). The collision of particles with bubbles is related to factors such as particle size and density, bubble size, bubble rise rate (Qin et al., 2012). Zongfu Dai et al. (2000) summarized the particle-bubble collisions models in detail and compared the experiment results with the model predictions. However, particle-bubble interactions occur in complex and turbulent flotation environments (Xing et al., 2017). Both thermodynamics and dynamic factors affect the adhesion of particles on bubbles surface (Schulze, 1989; Shahbazi et al., 2010). Scheludko et al. (1976) believes that the necessary condition for successful adhesion of particles on bubbles is that the contact time is greater than the induction time. The probability of adhesion between particles and bubbles increases with the increase of bubble size, but if the particle size is too small, the probability of adhesion decreases instead (Ren, et al. 2014; Norori- McCormac et al., 2017). After the particles adhere to the bubble surface, the particles will slide down to the bottom of the bubble due to gravity. At this point, the gravity, inertial centrifugal force and fluid force promote the desorption of particles from the bubble surface, while the surface tension, surface hydrophobic force maintain the stability of particles-bubble combination (Ralston et al.,2017). In addition, in the process of rising to the foam layer, desorption can also occurs. The purpose of this study is to observe the flotation behavior of fine fluorite with different size and to get a more comprehensive understanding of the interaction of fine fluorite particles and bubbles."

Jan 1, 2018

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By Z. Hu

A complex polymetallic sulfide ore in Yunnan, China, has various valuable minerals, which are Chalcopyrite, Galena, Pyrite, Gold, Silver, and Magnetite. A reasonable new flowsheet with a bulk flotation and a flotation separation of sulfide minerals that are Chalcopyrite, Galena, and Pyrite was carried out at first stage. After that tailings were treated by low intensity magnetic separation to achieve magnetite concentrate. A high Pb concentrate assaying 60.00 percent Pb at total recovery of 75.71 percent with 40.50 g/t Au and 1390.00 g/t Ag, a final high Cu concentrate assaying 24.45 percent Cu at high recovery of 92.03 percent and a magnetite concentrate assaying 60.78 percent Fe at recovery of 33.61 percent with 18.45g/t Au and 234.99 g/t Ag, are obtained. The total recovery of Gold and Silver in Pb concentrate and Cu concentrate reached 71.63 percent and 67.32 percent, respectively. It is shown, that this new flowsheet could realize efficient recovery for all of the valuable minerals in the ore and is easy to be industrialized. Keywords: bulk flotation, magnetic separation, polymetallic sulfide ore, depressant

Sep 1, 2012

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014

By S. L. Zheng

The compound material of Nano-TiO2 Supported on the diatomite was prepared by the hydrolytic method with purified diatomite and TiCl4. The compound material was characterized by SEM, XRD, TEM, EDX, XPS, and the application test of the compound material was studied. The characterization test results showed that the Nano-TiO2 was coated on the surface of diatomite, the crystal of TiO2 is anatase, and the average crystal size is 12 nm. The pore diameter was reduced, but pore volume and surface area of the compound material are increased after Nano-TiO2 Supported on the diatomite. The application test results for treating coking waste water and formaldehyde gas show that the compound material of Nano-TiO2 / diatomite has adsorption and photo-catalytic function and strong degradation performance for phenol and formaldehyde.

Jan 1, 2014

By R. X. Li

The overall flow-sheet of producing chromium (III) sulfate is described in this paper. The suitable conditions of each process such as sintering, leaching, aluminum removal, reduction, and de-composition conditions were experimentally studied. The results show it is reasonable to produce chromium (III) sulfate with the flow-sheet pointed out in this research work. The final product is Cr2(SO4)3 solution contained 150~250g/L Cr.

Jan 1, 2014

By Z. He

Based on full investigation of the characteristic of sphalerite in the residue obtained from cyanidation leaching process and the study of the mechanism of the interaction between flotation reagents and sphalerite with the aid of electrochemical analysis, the reagent named YO was developed for eliminating the depression effect of CN- on sphalerite and reducing the dosage of CuSO4. The achievements have been used in commercial production for the treatment of the cyanidation residue to recover the zinc minerals, obtaining a zinc concentrate with grade of 56.49% Zn and recovery of 86.63% Zn.

Jan 1, 2014

By Sun Chuanyao, Jia Muxin

Generally, if the bond valence (BV) between metal ion and oxygen of the mineral is greater than 0.8, only surface species –Me-O-H or –Me-O exposures on the mineral interface, if the BV is between 0.2-0.8, the metal ion exposures on the interface, and if the BV is less than 0.2 the metal ion dissolves into water. The PZCs of oxide minerals and island silicate minerals are determined by the bond valence of the bond in the mineral crystals, the higher the bond valence the lower the PZC of the mineral. So the PZC sequence of Al2SiO5 minerals is kyanite> andalusite> sillimanite. The general rule for framework silicate minerals is as: The higher the Al content, the lower the PZC of the mineral, when the ratio of Al to Si in the tetrahedron skeleton is below 1:3. The higher the Al content, the higher the PZC of the mineral, when the ratio of Al to Si in the skeleton is between 1:3 and 1:1. The general rule for layer silicate minerals is summarized as: the three-layer silicate minerals have much lower PZCs than that of the two-layer silicate minerals. The threelayer silicate mineral with the octahedron layer occupied by lower charged cations has lower PZC than that of the three-layer silicate mineral with the octahedron layer occupied by higher charged cations. The twolayer silicate mineral with the octahedron layer occupied by lower charged cations has higher PZC than that of the two-layer silicate mineral with the octahedron layer occupied by higher charged cations. The layer silicate mineral with Al substitution in the tetrahedron layer has lower PZC than that of the layer silicate mineral without Al substitution in the tetrahedron layer. Such pyroxene minerals whose M1 is occupied by a trivalence cation and the M2 is occupied by a monovalence cation has lower PZCs than those both M1 and M2 are all occupied by bivalence cations. Such hornblende minerals whose M2 is occupied by a trivalence cation and the M4 is occupied by a monovalence cation has lower PZCs than those both M2 and M4 are all occupied by bivalence cations. There is no Si4+ or 4 coordinated Al3+ exposures on the surface of framework silicate minerals, the metal ions of three layer or chain silicate minerals are compact between tetrahedron layersor chains, they hinder the metal ions to interact with oleate acid radical, the metal ion octahedron layer exposures on the surface of a two layer silicate mineral, but the the oleate acid radical can not attach to a metal ion by replacing a –OH- that connects three metal cations in the same time, So the floatability of such silicate mineral is bad. The metal octahedron chain style of an island silicate mineral affects it floatability, the mineral exposures octahedron chain metals with two dangling bonds in two directions floats better than the mineral exposures octahedron chain metals with two dangling bonds in one direction.

Jan 1, 2003

By Liu Yong

A complex rare metal ore, containing various valuable elements is used in this study. The mineralogy results indicate that the mineral composition of the raw ore is complex, and there are more than thirty-eight kinds of minerals in the raw ore, and the elements, such as Nb, Ti, Fe, REO, Be etc, always form isomorphism relationship. The REO content of the raw ore is 0.45%, and the contents of other rare metals Nb, Ta, Ti and Zr are 0.33%, 0.02%, 0.93% and 2.00% respectively, and the main gangue elements are Si and Al, and their contents are 71.84% and 8.5% respectively. The beneficiation-metallurgy combination process of ?preconcentration-reduction and magnetic separation-acidification and leaching-precipitation? is used to treat the raw ore. The preconcentration of raw ore is realized through high intensity magnetic separation, and the magnetic field intensity is 1.0T, and the rough concentrate with 2.88% REO and 1.95% Nbresidue can be obtained, and the iron recovery is 92.83%, and the REO recovery is 95.87%, and the Nbresidue is treated by hydrometallurgy process of ?acidification-leaching-precipitation?, then the rare earth oxide, niobium concentrate and zircon-bearing residue can be obtained, and the REO recovery is 80.10% and the Nbresidue and the gangue obtained from the high intensity magnetic separation process is separated by gravity separation, and then the zirconium concentrate can be obtained. The indexes of the beneficiation-metallurgy combination process used to treat the complex rare metal ore are as follows. The REO content of the rare earth oxide is 92.58% and the recovery is 58.44%. The Nb2O5 and 27.42% TFe can be obtained. Iron in rough concentrates is removed after reduction and low intensity magnetic separation, then the iron powder with Fe content over 88% and nonmagnetic rare-metal 2O5 recovery is 94.77%. The rare-metal 2O5 recovery is 80.04%. The mixture of the zircon-bearing 2O5 content of niobium concentrate is 28.34% and the recovery is 54.02%. The ZrO2 content of zirconium concentrate is 28.43% and the recovery is 52.35%. The TFe of iron powder is 89.53% and the recovery is 78.13%. Keywords: rare metal ore, separation and extraction, beneficiation-metallurgy combination, comprehensive utilization

Sep 1, 2012