Search Documents

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Xanthates (dithiocarbonates) have been the collector of choice for the flotation of sulfide minerals ever since the flotation process was developed and have been studied quite extensively. Recently, trithiocarbonates have been shown to be very effective in bulk sulfide bench-scale flotation. Fundamental analysis using electrochemical techniques have supported these bench-scale results, illustrating that the trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates, than the dithiocarbonate (DTC) collectors, as is shown in Figure 1.

Jan 1, 2003

By D. W. Feng

Thiosulfate as an alternative lixiviant for gold has received much attention in recent years due to the growing environmental concerns over the use of cyanide. Cu(II) is used to catalyze the oxidation of gold and ammonia is to stabilize Cu(II) in alkaline solution. However, the presence of Cu(II) enhances the oxidative degradation of thiosulfate. The high consumption of reagents has made thiosulfate leaching uneconomical to date, in comparison with cyanide leaching. Therefore, further investigations are required to leaching under low reagent concentrations over extended periods where reagent consumption is low and gold leaching rate is low as well. It is thus necessary to find additives to enhance gold dissolution in the thiosulfate leaching system. Electrochemical studies using rotating gold disc showed that the oxidation of gold in ammoniacal thiosulfate solution increased significantly in the presence of a small amount of thiourea and the beneficial effect increased with an increase in the thiourea concentration up to 7.2 mM. Thiourea improved gold extraction in the thiosulfate leaching of gold from a sulfide ore under low reagent concentrations. Excessive addition of thiourea inhibited the leaching of the gold ore. The decomposition of thiosulfate was reduced with the presence of thiourea. X-ray Photoelectron Spectroscopy (XPS) results indicated that thiou-rea likely decomposed to sulfide and formed gold sulfide species at the gold surface.

Jan 1, 2014

By O. Celep, H. Deveci, Ersin Y. Yazici, F. Ahlatci

"There are increasingly stricter environmental regulations imposed for use of cyanide leaching for the extraction of gold from ores. Alternative lixiviants to cyanide, preferably with low toxicity, have been extensively studied. Thiosulphate has emerged as one of the most suitable alternative leaching agent in place of cyanide due to its low toxicity and technical attributes e.g. fast leaching kinetics, high gold extractions from carbonaceous ores in particular. High solubility of most copper minerals in cyanide solutions results in low gold extractions due to excessively high consumption of cyanide. In contrast, low reactivity of copper minerals in thiosulphate solutions makes thiosulphate leaching potentially suitable alternative for treatment Cu-bearing gold ores. The extraction of gold/silver from a copper-bearing pyritic gold concentrate (62 g/t Au, 110 g/t Ag and 0.3% Cu) in thiosulphate solutions was investigated in this study. The concentrate is composed of predominantly quartz (25%) and pyrite (32.7%) as well as sphalerite (5.37%), galena (2.12%) and anglesite (1.13%). Other minor minerals are arsenopyrite, chalcopyrite, covellite and bournonite. Previous studies by the authors indicated that the concentrate did not respond well to cyanide leaching (i.e. 45-46% Au/Ag at 1 g/L NaCN). The effects of concentration of ammonia (0.2-1.5 M NH3), thiosulphate (0.1-0.75 M S2O3) and copper (0-20 mM CuSO4) on the extraction of gold and silver over 8 h. was investigated. Increasing the concentration of thiosulphate and ammonia substantially improved the rate and extent of gold leaching while high copper levels produced an adverse effect particularly at low concentration of thiosulphate (i.e. 0.1 M). Complete extraction of gold was achieved under suitable conditions. In contrast to gold, silver extractions remained consistently at low levels (i.e. 28%). These findings demonstrated that thiosulphate leaching could be used to achieve acceptable levels of gold extraction from the copper-bearing pyritic gold concentrate."

Jan 1, 2018

By Kazutoshi Haga, Batnasan Altansukh, Shirchinnamjil Nyamdelger, Atsushi Shibayama, Narankhuu Ariunbolor, Gunchin Burmaa

In this study, the authors investigated the capability of an acidic thiourea solution and silicon-organic polymers (PSTM-3c, PSTM-3T) as ion-exchange resins to recover of gold from gold-bearing ore concentrates. Firstly, elemental gold present in flotation concentrates was dissolved by leaching with a solution of nitric acid and thiourea under the optimized conditions. The best result on gold thiourea leaching was obtained under a nitric acid concentration of 2 N, thiourea concentration of 2 %, and oxidant (Fe2(SO4)3) concentration of 3 %, solid:liquid ratio (S:L) of 1:20, leaching time of 6 hours at 20 °C with a gold recovery of 93.7 % for a gold flotation (unroasted) concentrate. For the roasted gold concentrate, the dissolution of gold was 94.8% under the optimized leaching condition as nitric acid concentration of 0.5 N, thiourea concentration of 2 %, and the oxidant concentration of 1 %, S:L ratio of 1:10, leaching time of 4 hours at 50 °C. Secondly, a series of sorption tests was carried out on a pregnant leach solution containing gold complex Au[S=C(NH2)2]2+ using silicon-organic polymers (PSTM-3c and PSTM-3T), respectively. The effects of solution pH, adsorption time and temperature in the sorption process are also studied. As the results, the PSTM-3c and PSTM-3T polymers were adsorbed about 94.4 % and 95.1 % gold from the pregnant leach solutions under the optimum sorption conditions, respectively. It was found that the both PSTM-3c and PSTM-3T polymers were effective for the recovery of gold from the pregnant leach solution of thiourea. Adsorption activity of the PSTM-3c and PSTM-3T polymers was confirmed by new peaks near 1700 cm-1 in the FT-IR spectrum of the gold-adsorbed polymers, respectively.

Jan 1, 2014

By Muammer Kaya, Sait Kursunoglu

"Energy is the major concern for society. It is expected that developing country economies and populations will grow and consume more energy. Interest in nuclear power is rising, while the world looks for non-depletable energy source that will not contribute to global warming. However, it still has concerns of nuclear proliferation, radioactive waste and safety. It is necessary to overcome these concerns if nuclear energy is expanded to developing countries. Thorium (Th) utilization as nuclear fuel will be an opening key of these difficulties because Th produces less Plutonium (Pu) and less radioactive waste with enhanced safety. Research into the use of Th as a nuclear fuel has been taking place over forty years, through with much less intensity than that for uranium (U) or U-Pu fuels. Nuclear industry is currently using only 0.7% of the available energy from mined U. With huge resources of Th and relatively little U, Turkey has made utilization of Th for large-scale energy production a major goal in its nuclear power programme. Thorium fuel is plentiful and inexpensive. Energy is major concern for developing Turkish society. Turkey, today exports more than 70% of its energy as fossil fuels. In the last 50 years, Turks are skeptical, anxious and indecisive about having nuclear energy for electricity production. In the last 10 years, Thorium is brought into Turkish government’s attention and national discussion as a new, safe, clean, affordable, CO2-free, alternative, strategic and domestic nuclear energy fuel. Turkey recently contacted four VVER-1200 type Russian Nuclear Power Reactors using U as a fuel in Akkuyu (Rosatom) and another four units will be established in Sinop in the next decade by Japan (Mitsubishi-Westinghouse). Turkish nuclear programme must envisage use of domestic Th as a fertile material. This paper briefly reviews the developments of Th-fuel cycle for nuclear energy from global and Turkish perspectives. Previous Th reserve development and recovery studies from Turkish bastnasite ore are summarized in this paper."

Jan 1, 2014

By N. Naudé

The theory on particles displacement subjected to upwards and settling movements in water, using a water pulse, is described in literature, but very little experimental data is available to verify these theoretical ideas. The aim of this research work was to visualize the displacement of solid particles in a mixture of water and solid particles created with the aid of water pulses in the Mineral Density Separator. From the literature it is known that lighter particles are subjected to higher levels of displacement than heavier particles, and when the particles then settled down, layers of material are formed ac-cording to the densities of the material. By removing the individual material layers, the materials can then be separated according to their densities. During this study the individual material layers were investigated regarding the density and size distribution in that specific density layer. It is important for this project to have a statistical prediction of the ?real? flow of the particles with different density and size distribution, inside the Mineral Density Separator. The information gathered during this study will be used to show the correlation between a two dimensional model of the particle flow and that of the real three dimensional flow inside the Mineral Density Separator.

Jan 1, 2014

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By Kaiwen Liu

Activated carbon is widely used in the removal of organic and/or inorganic contaminants from waste water due to its high surface area, porous structure, and specific surface reactivity. However, in practical applications, it is difficult to recover the activated carbon completely by screening or classification. In this project,we prepared a magnetic form of activated carbon (magnetic activated carbon or M-AC) by precipitation of iron oxides on the surface of activated carbon. The M-AC can be easily separated from effluents by applying an external magnetic field, thus it can be recycled and regenerated for reuse. M-AC was characterized by X-ray diffraction (XRD), specific surface area measurement, and scanning electron microscope (SEM).XRD results show that the major phase of coated iron oxides on activated carbon is magnetite (Fe3O4). The specific surface area of activated carbon was found to be reduced after the impregnation of magnetite particles on the surface. The SEM micrograph shows the aggregation of the iron oxides on the surface of activated carbon. M-ACwas found effective in removing DETA (diethylenetriamine) species and metal ions from solutions. Cu (II) with initial concentrations from 5 ppm to25 ppm in solution is removed by more than 99% with the addition of 0.1 wt.%ofM-AC. For the removal of 25 ppm DETA species from solution, an addition of 0.5 wt.% of M-AC is required due to the larger size of the DETA molecule. Moreover, M-AC showed a good loadingproperty for nickel and gold ions from solutions. M-ACshows a better adsorption capacityover activated carbon and its potential applications in carbon-in-pulp for gold leaching and waste water treatment. Keywords: magnetic activated carbon (M-AC),diethylenetriamine (DETA),metal ion,adsorption

Sep 1, 2012

By Slobodan B. Vujic

"Some twenty years ago, during construction of flotation in the “Veliki Krivelj” copper and non-metallic mine Bor, a computer supported system for remote controle of technological process was installed. Nowadays, the major part of equipment of this system is worn-out and technically old-fashioned. Having this in mind a decision was made to design a new computer supported information-management system for Flotation. The paper presents a concept and features of project solutions.For the requirements of remote monitoring and management of technological process in Flotation of “Veliki Krivelj”, Copper and non-metallic minerals mine in Bor, Yugoslavia (hereinafter: CNM Bor), a measuring-regulation equipment was implemented and a computer control system, adjusted for that time, built some twenty years ago. The major part of this equipment is today worn out and technically out of date.Having estimated that production and business activities could hardly be more efficient, operative and successful on one hand, and available mineral and other resources rationally exploited, the CNM Bor made a decision in 1999 to improve information-management function of Flotation. The idea was that the set task be realized through development and introduction into practice up-to-date integrated and computer-supported production-business information-management system. The first logic step in completion of this task refers to engineering-creative determination of information management system (hereinafter: IMS), namely to project elaboration.When considering the real system from technical, technological, organization, monitoring-management, logistic and business aspects, the Project on IMS of Flotation, should provide a rational, modern and, for the real system conditions, complete solution. The Project solutions should be based on the most recent knowledge from computer and measuring-regulation technics as well as from CIM concept (Computer Integrated Manufacturing)."

Jan 1, 2003

By Francesco Montanari, Gianni Schena

"Recent improvements in X-ray computed tomography allow investigation of objects several tens of millimetres in dimension with spatial resolutions in the order of a few microns. These improvements are made possible by coupling the micro-focus technology adopted by some of the latest cone-beam X-ray sources with an increase in the efficiency of the detectors. The micro-focus technology allows the production of clearer images at high magnification by reducing the penumbra (fuzziness) associated with larger focal spot size.Even higher resolutions can be expected in the next few years with the commercialisation of nano-focus X-ray tubes. In practice one can inspect a system of fine composite particles and analyze the different mineralogical phases in each individual particle. Computed tomography allows accurate liberation studies, e.g. providing liberation spectra or washability data in tens of minutes. However, on-line application of micro-focus computed tomography is unlikely in the foreseeable future, despite rapid development.Dual-energy (DE) radiography is another X-ray technique, which allows retrieval of the volumetric content of valuable components in two-phase particles in a fraction of a second. A digital radiograph of a single two-phase particle produces a grey level image, where the luminosity of the pixels is determined by the sum of the attenuation levels of all the structures. Thus morphological and compositional effects concur to produce the radiographic image, which does not allow retrieval of the composition of the particle, as the 3D-structure of the particle is compressed into a 2D-image, with an obvious loss of information. Thus, in principle it is not possible to discriminate between thick, comparatively penetrable, and thin, comparatively impenetrable mineralogical components."

Jan 1, 2003

By Gianni Shena, Francesco Montanari

"Recent improvements in the resolution of X-ray computed tomography (CT) make it a promising alternative to traditional time consuming, error prone laboratory procedures for mineral liberation analysis, such as heavy liquid fractioning and measurements on polished sections. All indications are that in a few years CT will be well-established in many laboratories as a rapid technique for accurate liberation studies. In this scenario it would be able to provide liberation spectra or washability data in tens of minutes following sampling. However, although CT is a fast evolving technology, its on-line application is unlikely in the foreseeable future.Dual-energy (DE) radiography is another X-ray technique originating from non-destructive evaluation (NDE) and medical fields, which allows retrieval of the volumetric content of valuable components from two-phase particles in a fraction of second. Two radiographic images at different X-ray energies of a single particle or a monolayer of particles are taken in short time sequence. The thickness of the two phases is calculated particle by particle by image subtraction, whereupon particle grades can be derived. The development of the method for on-line applications requires the presentation of non-overlapping particles in the gap in the X-ray source detector measurement couple. Straightforward extension of the principle to multiphase systems is not possible. The paper reviews the state of the art of these two techniques as applied to mineral liberation problems."

Jan 1, 2003

By Peter N. Holtham, Geoffrey J. Lyman, The University of Queensland, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong

"The cyclone would have a claim to be the commonest, least understood and most abused piece of mineral processing equipment available for study by researchers. It has certainly generated its fair share of publications – 1,000 in the last 60 years would be a fair estimate. However this remarkable degree of interest and scale of investigation is not reflected in our understanding of how they work; cyclones are still installed inappropriately and run poorly, which suggests that there are still things to learn about this deceptively simple process.In mineral processing there are two broad classes of cyclone: the hydrocyclone, used in classification, thickening and dewatering, and the dense medium cyclone, used for concentration by density. Although rarely studied together, the laws of physics presumably apply equally to both and so it seems that there would be interesting things to learn by considering them as a single class of device. The good news is that in recent years there have been spectacular advances in the computational and measurement tools available to study these devices, including computational fluid dynamics (CFD), tomography, and laser doppler anemometry (LDA), and some good progress has been made in an understanding of the fundamental principles involved.The JKMRC has made many experimental studies of hydrocyclones and DM cyclones, leading to useful empirical models. However some recent CFD and tomographic work, in association with work of other institutions, has thrown important light on the workings of these processes. Progress has also been made in novel designs of cyclone to achieve improved separating efficiency, based on an attack on the subprocesses believed to contribute to inefficient operation. This paper describes the work to date.Modelling of the dense medium and classifying cyclone was conducted using the Fluent computational fluid dynamics code. Three phase simulations of the dense medium application (air/water/medium) showed appropriate medium segregation effects but over-predicted the level of segregation compared to segregation measured by gamma-ray tomography. This is believed to be because the basic Algebraic Slip mixture model in Fluent does not model any back-mixing of the dispersed phase due to turbulence."

Jan 1, 2003

By Peter N. Holtham, Geoffrey J. Lyman, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong, Tim Napier-Munn

Studies of the dense medium and classifying cyclone have been conducted using the Fluent computational fluid dynamics code. Experimental measurements of the segregation of medium in a DM cyclone by gamma-ray tomography and the performance of a novel classifying cyclone design have been used to test and interpret the 3D CFD predictions. The predictions of the CFD models were generally plausible, though more work is required to incorporate turbulent mixing of the slurry in the cyclone. The benefits of the novel cyclone design were explained by the model in terms of conditions favouring reduction of short-circuiting at the vortex finder, and the removal of the air core from the wall at the apex. Work is continuing.

Jan 1, 2003

By H. R. Manouchehri

"In mining and minerals industry, except profitability, there are some crucial factors that represent components in economic machinery of a mine and related activities. These are sustainability and minimizing environmental impact factor. Environmental concerns combined with the water and energy availability and related costs, as well as public license to operate all contrive to demand for more efforts targeting sustainability. Mining industry is highly energy-intensive (estimated to consume 6-7% of total world’s energy), with varying the energy efficiency across the industry resulting in significant costs. Size reduction is the main energy consumer contributing to almost 50% of the total energy used in mining. That means efforts must be made to introduce energy efficient comminution flow-sheets and machineries for sustainable development. Since the crushers are more energy efficient than mills, it is logic to push down-sizing in crushing stage(s) as far as technically possible. That has been strategy for Sandvik Mining and Rock Technology in supplying advanced and effective crushers to provide fine crushed product for subsequent milling stage. Lowering the energy consumption and related costs as well as increasing throughput have been the main objectives in design and development of comminution circuits and related machineries. Inefficiency in comminution technology, particularly in grinding, has long been regarded as a major area for investigation and development, especially when production of fines and ultra-fines are considered. In an attempt to explore the potential of fine crushing and its effects on subsequent milling process the fine crushing performance of Sandvik’s conventional cone crusher and Vertical Shaft Impactor (VSI) in pilot scale to define the energy consumption and circulating load in fine crushing. Tests were conducted to obtain fine crushed products at P = 2 mm in a close circuit. Furthermore, the crushed products were characterized and compared by grind-ability, morphology, and surface area measurement tests. Finally, the energy consumption to grind the crushed products to specific grind size was calculated."

Jan 1, 2018

By Nicolás Luis, Qi Liu, Gonzalo Montes-Atenas

"The prediction of froth flotation performance is still an unresolved topic. Classic industrial models based on particle size, elemental and mineralogical information provides recovery results with deviations that may become significant. One possible reason for this deviation may be the fact that the current liberation analysis provided by electron microscope based techniques does not take into account the outmost surface layer composition of liberated particles. In order to complete the description provided by the liberation analysis, other spectroscopy techniques measuring the extreme surface of the minerals can be tested. For instance, X-ray Photoelectron Spectroscopy (XPS) is a technique which measures the first tens of nanometers providing elemental composition over the particle surface and allows resolving the elemental associations present at the surface sample. However, this information needs to be statistically robust, reproducible and most importantly representative of what is occurring in the process. The aim of this research work is to develop a statistical model based on particle population to evaluate the feasibility of turning the XPS technique into a metallurgical tool. The model consists of classic statistical population arranged in a bed of heterogeneous particles with a known grade and mineral liberation. The simulations showed that the XPS results statistically followed a well-defined pattern. The statistical results were confronted with pilot plant results obtained from a rougher bank when processing a copper sulfide ore from a Chilean mine site. It was observed that the probability function distribution was in agreement with the experimental data. Further analysis on how the XPS results provide valuable information improve the computation of froth flotation recoveries is also discussed."

Jan 1, 2014

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By Carlos Collado, Oscar Jimenez, Francisco Diaz, Rodrigo Bernal, Carmen Salinas

Water is a strategic resource for the mining industry. The rising cost has forced the industry to become more efficient in their use, reduce and recycle waste as much as possible. The importance of having a reliable water balance is increasingly urgent, because the resource is scarce and vital to the sustainability of human life, animal and ecosystem. Conventional flowmeters can suffer disruptions or failures by corrosion, fouling, presence of elements in the water as acids, salts and suspended solids. Use of radiotracers is advantageous to determine fluid velocities that are transported through pipes, as they are detectable by means of the radiation emitted, the same way for surface flows, such as natural watercourses and drainage from tailings dams, fluorescent tracers are those with the best advantages. For velocity measurements in pipelines a Iodine-131 tracer solution, around 5 mCi was injected into the suction of the pumps. The technique used is the transit time between detectors at known distances and determining the time of passage of the radiotracer. For measurements of surface fluxes using the fluorescent tracer Rhodamine WT by tracer dilution technique, injecting the tracer at a constant rate and measuring it known concentration diluted downstream. This work has been performed in Minera Los Pelambres, located in the IV Region of Chile, measuring the flow rate pumped from 12 pools with 1-7 pumps operating, obtaining speeds of 0.56 to 2.62 m/s. In pumping wells three facilities have been measured at speeds of 0.111-0.223 m/s, plus six surface flows with flow rates of 8.45 to 357.2 L/s.

Jan 1, 2014

By N. N. Ngoepe

Positron Emission particle tracking (PEPT), which makes use of a radioactively labeled tracer particle, a positron camera and a tracking algorithm has been shown to be a viable method for studying flow properties in both the pulp and froth phases of flotation cells. Detailed velocity measurements of 300-400 µm glass beads were extracted to assess turbulence from velocity fluctuations in a micro flotation cell. The effects of particle speed and orientation at the instant of attachment events were studied. A minimum speed of 0.16 m/s was needed for a collision to lead to attachment. The most attachment events happen when the particle is directly in line with the inlet tube at 90o.

Sep 1, 2012