Search Documents

By Ricardo Montero

At this time, over 300 tons of Au are used in electronic equipment each year with other precious and strategic metals such as Ag, Pt, Pd, Cu, Nb, Ta, etc. After the use-phase, the electronic devices become electronic waste (e-waste); consequently it is important to consider e-waste as a secondary supply for recovery of these metals. One of the most important components is the printed circuit boards (PCBs) because the amount of their precious metals is ten times higher than rich precious metals bearing ore. This paper presents the recovery of Au, Ag, Cu and Nb from PCBs of discarded computers using leaching column technique. The amount of these metals in used PCBs was: 613 g/ton of Au, 1515 g/ton of Ag, 36 g/ton of Nb and 23.4 % of Cu. The PCBs were crushed with a hammer mill until reaching a particle size between 3.33 mm to 0.43 mm. Then, it was leached with sodium cyanide solution in a glass column using the following conditions: sodium cyanide concentration 4 g/L, flux 20 L/kg PCBs day, pH between 10.5 to 11 and leaching time 15 days. Every day, after leaching, the pregnant solutions passed through a column with activated carbon to complete the closed loop system. The following recoveries were obtained: 46.6% of Au, 51.3% of Ag, 47.2% of Nb and 62.3 % of Cu. The products obtained are: a) loaded carbon that contains the desired metals and b) processed PCBs with precious metal contents. A preliminary technical-economic study shows the feasibility to create a small-scale PCBs recycling plant. The initial investment is on the order of US$ 155 639, considering the recovered metals from loaded carbon. The internal rate of return for 10 years period (IRR) and net present value (NPV) estimated are 27% and US$ 105 926 respectively. Keywords: printed circuit boards, recovery, precious metals, niobium, leaching column

Sep 1, 2012

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By T. Fujita

A high-grade fluorite ore is converted into hydrogen fluoride to produce many kinds of materials containing fluorine. Recently, it is becoming necessary to use low-grade fluorite ore due to the depletion of high grade ore. The low-grade fluorites usually have impurities such as SiO2, P, CaCO3 and arsenic. The most impurities such as SiO2, CaCO3 and P can be removed by using flotation method. However, the removal of arsenic is difficult, and the arsenic contamination decreases the hydrogen fluoride production percentage. The novel technologies for processing low-grade fluorite ore are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, the removal of arsenic from low-grade fluorite ore has been investigated by means of an autogenous grinding using tower mill in sulfuric acid aqueous solution and 0.3 mm zirconia balls in water. The nano grinding in water can prevent the dissolution of 0.3 mm size zirconia balls as grinding media by sulfuric acid solution. Experimental results showed that the arsenic concentration was reduced from 260 mg/kg to 90 mg/kg and CaF2 recovery reached 90% by this process.

Sep 1, 2012

By Jacek Kolacz

A new sensor based sorting system related to complex image analysis has been developed at Comex AS - Norway. It makes it possible to separate different mineral particles regarding their color, shape, texture, size, density and indirectly their composition. The sorting system has been successfully tested and applied for sorting minerals providing high separation efficiency in the range of 95-99.9 %. The main advantage of this system is connected with its universality where many material parameters are analyzed in the same processing unit by a single passage.

Sep 1, 2012

By A. A. Lavrinenko

There are discussed the possibilities of using of flotation tailings of platinum-copper-nickel sulfide ores of the Norilsk region for the preparation of backfill mixture instead of a specially produced rock and binder materials to reduce the cost of stowing operations and impact on the environment. It is shown that due to the presence in the tailings of flotation up to 10% of sulfide sulphur, which reduces the strength of the fill materials, and more than 1 g/t PGM it is necessary the preliminary extraction of the sulfides in the product for further processing that give an opportunity to reduce the losses of valuable components. It is shown that by the flotation of the current tailings it is possible to extract 91% of sulfide sulphur, 60% of palladium and 30% platinum in 17% sulfide concentrate containing 2.1 g/t palladium, and to reduce the sulphur content in the tailings up to 0.7%. Due to the easy oxidation of pyrrhotite, there is recommended fractional delivery of the collector with a total consumption 200 g/t. There are discussed results of the flotation study with an additional collector of PGM (sodium diizobutyditiophosfinate), which one show the possibility to increase extraction of platinum on 45%, as well as extraction of sulphur and palladium. For the flotation of sulfides and PGM from the current tailings there is recommended a combination of collectors for primary flotation and only butyl xanthate using in control operations. The possibility of using sludge fraction of the current tailings as a component for the preparation of the combined cementing materials after exposure of sulfides is analyzed. It is shown that the efficiency of the flotation of sulfides from this fraction can be enhanced using selective flocculants. There are discussed the advantages of implementation of completely hydrophobic butadiene-styrene copolymer in comparison with partially hydrophobic polymers. There is discussed an efficiency of the mechanochemical treatment of old tailings in turbo mill and sulphuric acid to remove oxide films from the surface of pyrrhotite before its flotation. Due to the pretreatment operation there is achieved increasing of sulphur extraction and after the introduction to the flotation circuit three control operations there is produced the fill material with sulphur content 2.5%. Keywords: tailings, copper-nickel ore, pyrrhotite, butyl xanthate, sodium diisobutyl dithiophosphinate, selective flocculation, butadiene-styrene copolymer, mechanochemical treatment

Sep 1, 2012

By Liang Dianyin

In this paper, the molybdenite flotation tailing of cleaner-scavenger bank which has a mass of very fine particles has been taken as raw ore to be processed by flotation with/without ultrasonic. The effect of ultrasonic frequency, intensity, processing time and uploading location on molybdenite flotation efficiency is investigated by four-factor three-level orthogonal experiment, and the effect significances of these ultrasonic variables to molybdenite flotation efficiency have also been evaluated. Single-factor analysis of variance is conducted to investigate whether the effect of ultrasonic on molybdenum ore flotation efficiency is significant or not. The samples extracted from different ore species in different time have been mixed to analyze the particle size. The results show that the particle size of +38µm in concentrate obviously increases while the particle size of -25µmobviouslydecreaseswith ultrasonic, which means that ultrasonic is good for flotation due to sludge removing effect. Keywords: ultrasonic, flotation efficiency, sulfide ore, tailing, grade, sludge removing

Sep 1, 2012

By Nidhi Kumari

This work is based on surface chemical properties of bacteria during adaptation to high grade copper minerals and the projected consequences in Bio-Flotation process. The utility of bio-processing in the beneficiation of copper ore through bio-flotation is demonstrated. An autotroph Acidithiobacillus Ferrooxidans bacterium is adapted to high grade mixed copper ore sample by repeated subcultures. The surface characteristics were studies by analyses at different pH and time intervals. From the studies, it was established that the mineral-adapted cells became more hydrophobic as compared to unadapted cells during bio-flotation. It was also noticed that there was no significant changes in the surface charge of bacteria before and after adaptation. Keywords: bio-flotation, copper, Acidithiobacillus ferrooxidans, hydrophobic

Sep 1, 2012

The quality of iron ore fines in terms of high iron content and low levels of deleterious impurities such as Silica, Alumina, Sulphur and Phosphorous is a critical parameter, in sintering and subsequent iron and steel making processes. As the higher-grade ores become depleted, there will be a stronger focus on treating lower-grade haematite/goethite ores and developing suitable beneficiation techniques to reduce the levels of impurities. Innovative flow sheets, based on new and commercially available technologies, is required. These will be needed to include gravity concentration devices, which can handle coarse and fine feed sizes. In this paper, efforts made to reduce the silica and alumina content of a low grade iron ore fines (<1.0 mm size) sample from the Pilbara region in Western Australia are described. The feed sample, a goethite abundant lower grade iron ore fines, which was a plant reject assaying 48.66% Fe with 13.61% SiO2and 5.09% Al2O3 was investigated. To this end, an experimental campaign was undertaken, and beneficiation studies were conducted on the sample using a Floatex Density Separator (FDS), a gravity device which can be operated for size classification and/or relative density separation. The objective was to produce high-quality iron ore material suitable as sinter feed. An iron concentrate with a grade around 57.0% Fe (Calcined Fe of about 63.0%) was achieved while recovering around 67.0% of the feed weight. In addition, a rejection of substantial content of Silica (>75%) and Alumina (>66%) was achieved while securing >77% iron recovery. On the other hand, sharp classification efficiency with low values of imperfection around 0.20 was obtained. Consequently, the response of the lower grade iron ore sample to FDS application, has vast potential to reject deleterious impurities as a single stage separating beneficiation equipment. Remarkably, it was demonstrated, that a great amount of goethite, abundant in lower grade iron ore fines/plant rejects, which are currently being either stockpiled and/or dumped as waste, can be treated using FDS application and potentially can add a significant value to the iron ore mining industry by recovering additional iron ore fines. Keywords: deleterious impurities, beneficiation techniques, classification, relative density separation

Sep 1, 2012

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

By Shugang Hu

According to XRD, DTA and SEM detections, the hydration products of blast furnace slag (BFS) based cementing material SL, SLG. were studied in different age periods. The XRD analysis of cementing material SL hydration products showed that the composition of hydration products were mainly amorphous substances, few crystalline substances. Characteristic peak of ettringite hadn?t been found in the spectral line of DTA, and it hadn?t been found in the figures of SEM, either, which was accordant with the conclusion that the cementing performance of SL mainly coming from gel of hydrated calcium silicate (CSH) and hydrated calcium aluminate. However, the main hydration products of SLG are Aft, CSH, and AFm, which are similar to Portland cement. All results suggest that BFS is a suitable base material for cementation. Keywords: blast furnace slag, backfilling cementing material, hydration products, cementing performance

Sep 1, 2012

By Graeme J. Jameson

In conventional flotation machines, the recovery is strongly related to particle size. As particle size increases, the recovery also increases, reaching a maximum in the range 20 to 120µm. Beyond this range however, the recovery declines quite quickly. The reason for the decline in recovery observed with coarse particles can be traced to the effect of turbulence. Bubbles trapped in turbulent eddies rotate rapidly, and when the centrifugal force on a particle exceeds the retaining forces due to surface tension, the particle detaches. Since the centrifugal force varies as the cube of the diameter of the particle, and the attachment force varies simply as the diameter, being proportional to the length of the contact line, it is clear that detachment forces will predominate as the particle size increases. The corollary is that the recovery of coarse particles can be improved if the level of the turbulence in the cell can be reduced to a minimum. In this paper, a new type of flotation machine will be described, in which the particles to be floated are suspended in a fluidized bed. An up flow of fluidizing water is provided, by recycling liquid from the top of the cell. The recycle stream is aerated in a high-energy device that disperses the air into fine bubbles that capture the fines and ultrafines. Results are presented for several minerals and coarse coal. Keyword: fluidized bed flotation

Sep 1, 2012

By A. R. Hasankhoei

Water recycling is of prime importance in mineral processing due to consumption of large amount of water. This issue is vital in areas with a low rainfall such as Shahre-Babak (Kerman, Iran). Deep cone thickeners, unlike conventional thickeners, have a low diameter to height ratio where large amounts of flocculants are used to increase particles settling rates. The high bed heights (over 10 m) produce enough pressure to create a paste type underflow indicating maximum water recovery. Flocculent preparation, conditioning, and distribution along with the bed height are among the important factors affecting the performance. Four deep cones are used to recover water from the tailings of the plant. Plant data indicated that the thickener never reached the target underflow percent solids (63%) and the average underflow concentrations were between 49 and 57%. By modification and optimization of flocculent preparation and distribution methods the underflow percent solids increased by 3-4%. This translated to an increase of water recovery from 67 to 73%. This was equivalent of 53000 m3 saving in monthly water consumption. Keywords: deep cone thickener, water recovery, flocculant, copper tailings

Sep 1, 2012

Due to complex mineralogical and chemical interactions of the value and gangue mineral phases present in uranium-containing lateritic ores, deleterious pulp gelation which impacts on value metal recovery sometimes occur during atmospheric leaching. In this study, the leaching behavior and particle interactions of selected oxide (hematite, quartz) and clay minerals (muscovite, chlorite), which constitute predominant host gangue phases of typical lateritic uranium ores are investigated to provide basic, mechanistic understanding of temporal pulp gelation phenomenon. Isothermal, batch leaching with H2SO4 was carried out on concentrated dispersions (30 ? 57 wt.%) of single minerals at pH 1 and 25 or 70 °C and their concomitant solution, speciation and rheology (shear yield stress, viscosity) were characterized. It is clearly shown that despite the high oxide content of lateritic ores, the pulp chemistry and rheology is largely affected by the incongruent leaching behavior of more reactive, acid-consuming aluminosilicate clays. Furthermore, time- and temperature-dependent alumino-silicate species polycondensation interfacial reactions are shown to be responsible for the enhanced particle interactions, reflecting strong pulp rheology in agitation and pumping. If not properly mitigated, high pulp shear yield stress and viscosity have a striking impact on processability and hence, value metal recovery.

Sep 1, 2012

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By H. Deng

Oxidized zinc ores are the main source of zinc metal except sulfides. To have a better understanding about the performance of smithsonite and the main gangue, quartz, in flotation, the aggregation behaviors of smithsonite and quartz in water were confirmed by different techniques (sedimentation tests and optical microscopy). The experimental results show that smithsonite and quartz particles aggregate in the pH range 7.5-11. The results of zeta potential suggest that the aggregation does not correlate with the DLVO theory, when the iso-electric point of smithsonite and quartz is 8.0 and 2 respectively. When the solution pH is less than 8.0, smithsonite has an opposite charge to the quartz particles. Electrostatic adsorption makes effort on these two kinds of particles according to DLVO theory. Whereas, solution chemistry calculation shows the pH range 8-11 corresponds to hydroxide formation, suggesting that this is the species responsible for aggregation. And their concentrations are much higher in sodium hydroxide system than that in sodium carbonate system. Aggregation of smithsonite and quartz due to the flocculation action of zinc hydroxide is proposed.

Sep 1, 2012

A new short combined flow sheet including high intensity magnetic separation and flotation for a rare earth ore in Maoniuping deposit, China has been investigated. Massive conclusive results demonstrate, that it is critical to separate the ore by high intensity magnetic separation prior to flotation for tons of slimes and nonmagnetic gangue existing. The vital technological parameters affecting flotation have been studied in detail. Modified hydroxamic acid is an efficient collector for bastnasite flotation because of its high selectivity. Flotation results also indicate high temperature that play an unfavourable role on the recovery as well as the grade of bastnasite concentrate, when the rare earth ore is floated with modified hydroxamic acid and sodium silicate depressant. Bastnasite concentrates, averaging over 65 percent REO at an overall recovery of 82-84% is achieved by the new beneficiation technology. Keywords: bastnasite, REO, magnetic separation, flotation, chelating collector, desliming

Sep 1, 2012

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By Yimin Zhu

This paper introduces the sixteen mappings and rules of mineral flotation and the subgroup, period etc in periodic table of chemical element to provide mineral flotation workers to refer in theory and practice research. the nine mappings and rules of mineral flotation and the subgroup, period are Saline minerals including the first main groups and collectors of aliphatic acid and aliphatic amines, Minerals including the second main group elements and collector of aliphatic acid, Hydrated ion of the second main group elements and quartz flotation, The floatability of oxidized minerals including the four main group elements, Organic acid including the fifth main group elements and wolframe, tin flotation collectors, The floatability of sulfide minerals including the fifth main group elements, Inorganic compounds including the seventh main group elements and mineral flotation regulator, Oxidized minerals including the forth Subgroup elements and organic flotation agents with phosphorus and arsenic, Oxidized minerals including the fifth subgroup elements and organic floating agents including the fifth main group elements, Minerals including the first subgroup elements and CN-, Sulfide minerals including the second subgroup elements and CN-, The effect of the highest N-valency inorganic acids or salts including p area elements of the third period in mineral flotation, Oxidized minerals including transition elements of the forth period and 3# flocculating agent, The floatability of minerals including elements of the sixth period, Element area of generating compositions and the collecting theory of mineral flotation and so and. Keywords: mineral flotation, periodic table of chemical element, subgroup, period, regulator, coordination chemistry

Sep 1, 2012

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

By S. M. Mustakim

Red mud is the major waste material produced during digestion of bauxite ores with caustic soda in alumina production following the Bayer?s process. Its disposal remains a worldwide issue in terms of environmental concerns. A lot of research and developmental activities are going on throughout the world to find effective utilization of red mud, which involves various product developments. At present, building materials, industries are fast growing industrial sector where the need of various raw materials is enormous. The use of red mud in building material production is one of the options for conservation of natural resources and reduction of environmental pollution. A cost-effective and energy efficient mineral cementation process has been developed at CSIR-IMMT, Bhubaneswar for use of red mud in manufacture of building brick, block and aggregate. The red mud is an alkaline material, which contains both leachable and non-leachable soda along with different mineral constituents of alumina, iron and silica. The effort has been made to use the mineral constituents of red mud to develop cold setting building brick by mineral cementation process using a binder specially prepared from Portland Slag Cement, Lime, Gypsum and Alkali metal sulfates. The red mud has been used from 40 to 70% by weight along with fly ash and binder in development of cold setting building brick conforming to the specification of IS:12894:2002.

Sep 1, 2012