Search Documents

By Michael David Wilkins, Paul N. Worsey

Little research has been published on stemming blast holes, particularly what happens during the process. Previous work has concentrated on the performance of the inert material to find the best way to seal the hole and retain the explosive energy, at the exclusion of determining what happens during the loading and stemming process.

Jan 1, 1998

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By S. Evans, J. Phillips-White, D. Morton

The partnership between Orica and MMG at the Dugald River Zinc mine in Australia has led to the first global field trials and deployment of Orica’s Subtek™ 4D™ (hereafter referred to as 4D) Bulk Systems underground bulk emulsion blasting technology. This technology offers advantages over conventional bulk explosives by extending the range of energy and length of explosive column that can be charged in underground production. 4D gives blast designers energy options between Relative Bulk Strength (RBS) 50 - 150, delivered uniformly along the entire column in most blasthole conditions along with the ability to instantaneously modify the energy within an individual blasthole. During Phases 1 – 3 of the project from October 2022 to January 2023, over 57 tonnes of the 4D Underground emulsion were loaded in 17 stopes. The primary objectives of this phase were to reduce hanging wall dilution and improve stope recovery. While drilling and other parameters remained unchanged, the energy selection was tailored for specific situations, guided by a revision to the site's drill and blast standard. The design used low energy (RBS 50 - 70) in holes adjacent to the hanging wall and high energy (RBS 130 - 150) where stope recovery had historically been challenging, such as at the toes of long downholes. Initial results of the project focused on five stopes selected for their similarity to those used for the baseline data set. Although the 4D data set was small, the post-blast scans indicated favourable results for recovery and dilution. This suggests that selecting and delivering bulk explosive with tailored energy levels can improve stope performance.

Jan 1, 2024

By Erik Nygaard

During the last years, ammonium nitrate has been involved in several accidents worldwide. This have caused increased focus on security and safety issues and resulted in:• Revised Yara standards • Revised international standards for storage and transportation • Stricter regulations from national authorities in many countries.

Jan 1, 2008

By Syed Haq, Kyle Optt, David Campo, Doug Anderson

Limitations on allowable levels of vibration from construction activities generally consider either annoyance or damage. While activities such as drilling and roller compaction primarily create annoyance, the major concern for blasting is usually damage. Many years of research have developed correlations between peak particle velocity and either threshold or structural damage. We emphasize the term “correlation” for two reasons. First, peak particle velocity is only a single-valued representation of a vibration waveform, and does not characterize it completely. Second, a given peak particle velocity by itself, even a particle velocity waveform, will not damage anything – strain does. Why not measure strain all the time? Strain is very localized, and can vary substantially over short distances, so choosing the appropriate strain measurement can be difficult. Measurement of strain is appropriate when either the behavior of a specific structural element is needed, or the overall response of a structure can be adequately represented by a well-selected strain measurement. We will discuss the appropriateness of both particle velocity and strain as deformation and damage descriptors, in general. We will also describe a specific case history, from a tunnel project in New Jersey, correlating strain with peak particle velocity. Finally, we will make recommendations for the choice of measurement type for some common situations.

Jan 1, 2004

By Cathy Aimone-Martin, Brent Meins

A comprehensive instrumentation program was implemented at the Howland Hook Marine Terminal on Staten Island, NY during proximate underwater rock blasting in 2014. Forty-two blasts took place over a 4-week period to deepen the 1200-ft (366 m) Berth 3 from -45 ft (-14 m) to -50 ft (-15 m) MLW to accommodate Post-Panamax vessels. Approximately 86,000 yd3 (65,752 m3) were blasted 120 to 9 ft (37 to 2.7 m) from the wharf to a total depth of -57 ft (-17.4 m). Pre-blast planning included developing and implementing a comprehensive monitoring plan and setting vibration and strain limits to protect the wharf. The plan outlined methods to measure vibrations on five corners of four concrete deck sections, on five concrete-filled pipe piles just below the pile cap near deck corners, and in bedrock adjacent to pile sockets. Water overpressures were measured near instrumented piles for 19 blasts closest to the wharf. A total of 19 geophones were secured to the wharf structure and buried 12 ft (3.7 m) in drilled holes.

Jan 1, 2016

By Catherine T. Aimone-Martin, Meyers Joseph A.

A new strain-based criteria is being adopted for rock blasting in New York City (NYC). This criteria is based on several years of research involving vibration measurements of tall structures during blasting within several feet from buildings designated historic and Landmarked. This research has demonstrated that tall, heavy structures show little upper-structure vibratory response during hard-rock, urban blasting carried out in NYC. The Fire Department of New York City (FDNY) permits rock blasting and regulated limits for ground vibrations using the U.S. Bureau of Mines (USBM) safe blasting criteria. However, these regulations are often superseded by a 0.5 in/s (12.7 mm/s) limit imposed by the New York City Department of Buildings for historic and Landmarked buildings that are adjacent to the majority of blasting projects in the City. This onerous limit is often exceeded resulting in frequent stop work orders that increase the cost and time of rock excavation projects. The

Jan 1, 2019

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Donald H. Matthews

The Society of Explosives Engineers is an international organization of over four hundred members involved in the explosives industry, with most members being active in the United States. The regulations imposed by regulatory agencies on the explosives industry have drastic effects far beyond the industry. Since explosives are used in mining, manufacturing, construction, entertainment, and art, all phases of man's activities, including fundamental needs for survival, are affected by how efficient the industry uses explosives. We, as members of SEE, must be sincerely concerned with both the quantity and quality of government regulation, and this paper spells out some of the problems caused by regulations and offers a solution.

Jan 1, 1980

By C. Rutledge

The new mining method of multiple strata blasting, called StratablastTM, is described in a separate paper presented at this conference. The current paper presents three case studies where the technique was implemented in three different configurations in large-scale blasts in Australia. The first two blasts were in the Hunter Valley of NSW while the third was at Ensham Mine in Central Queensland. All blasts comprised multiple layers that were blasted in a single drill and blast cycle, with unique designs applied to each layer to achieve different blast outcomes from the various layers.

Jan 1, 2006

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By Jake Hutchison, Wade Hutchison

The opposition to the project has risen as a result of some political pressures and from public perceptions about the project’s necessity and its impact on the neighborhood. As a result of this controversy, the Underground Conservation Hall was quickly termed “Bredesen’s Bunker” by the Media. Close exposures for blasting, required by the Conservation Hall construction project, have been regulated by specifications that regulate seismic monitoring, pre-blast and post-blast inspections. Planned blasting for the project included blasting to a depth of 30 feet (9.14 meters) within 35 feet (10.67 meters) of the front of the newly renovated Tennessee Executive Residence. Excavation for the project found more competent rock at higher elevations than identified in test drilling which required blasting within 2 feet (0.61 meters) of the side of the Residence.

Jan 1, 2009

By C. Kosloski, E. McCullough, A. Fox, S. Reed

This paper serves as a reference guide for creating or strengthening student chapters of the International Society of Explosives Engineers. This includes chapters that are just starting, currently undergoing transition in leadership, or that are in the process of rebuilding. ISEE student chapters have great potential to increase student involvement and national membership, and can benefit from formalized strategies to help them do so. Several key strategies are introduced and should be employed to promote organizational participation throughout the university system.

Jan 1, 2016

By Rick W. Bellenie, Ronald L. Woolf

The Gregg River mine is located 40 kilometres (25 miles) south of Hinton, Alberta, approximately 330 kilometres (205 miles) west of Edmonton and lies against the Front Range of the Rocky Mountains.

Jan 1, 1994

By Frank Hirthammer

Over the past few years, development and implementation of digital logistics solutions has convinced users of many additional advantages of this technology. Barcode labeling and reading increases the company’s efficiency and safety by reducing handwritten documentation and preventing misinformation. Sustainable information and productivity management is a significant advantage in competition. Since manufacturing information is tracked throughout the whole supply chain until the final consumer, all processes become transparent what ensures efficient risk tracking, correct disclosure to authorities (if required), and the compliance with company rules.

Jan 1, 2018

By Jennifer Paukula, Steven Lindsay, S. Joon Kim

String loading is the placement of a bead or ‘string’ of emulsion along the lower edge of a development drill hole. The loading hose extraction rate controls the amount of emulsion placed in each drill hole. This allows a controlled distribution of explosive energy throughout the development round. Center holes are loaded using the slowest extraction rate causing the majority of the explosive energy to be placed in the center of the round. The loading hose is extracted successively faster for the buffer and perimeter holes causing less explosive energy to be placed near the edge of the blast. This causes less damage to the rock mass that remains in place after the development blast.

Jan 1, 2012

By James T. Ludwiczak

The state of Kentucky uses more explosives than any other state in the country. The majority of these explosives are used in underground and strip mines in the well-known coal fields of eastern and western Kentucky.

Jan 1, 1978

By Chantale Doucet, Mario Paventi, Malcolm Scoble, Yves Lizotte

Laboratory studies in homogeneous material indicate that the area of new surfaces created by blasting is proportional to the energy imparted to the material. Field studies, however, show that fragmentation is also related to the rockmass structure. This paper reviews ongoing compilation of a comprehensive and integrated blasting database which is based upon field monitoring and laboratory testing. A priority application of the database is to support attempts to more fully understand structural control over fragmentation. Database construction and the relative importance of rockmass physical and mechanical properties are considered in the paper. A methodology for data collection prior to, during and after blasting is reviewed. Data summaries from three case studies of blast performance in surface and underground mines are presented. These illustrate various aspects of the methodology, which included image analysis to quantify the fragment shape and remnant geology evident in the muckpile as part of the evaluation of structural control over fragmentation.

Jan 1, 1994

By G Alan Foster

Many complaints generated from blasting operations result from the marked human response to ground transmitted vibrations and air blast effects and so many authorities have considered the regulation of blasting in terms of human response rather than, as previously, in terms of preventing damage to structures.

Jan 1, 1981