Search Documents

By J. H. East, D. Harrington

"INTRODUCTION Mining at its best is not a clean occupation for either surface or underground employees; and this applies alike to coal, metal, and non-metallic mines. The employees are handling minerals that have been blasted, or broken by some means and are subjected to mineral dust, whether it is coal, quartz, or talc. The employees usually wear clothes specifically adapted to the work in which they are engaged, and frequently these clothes are not suitable for use away from the mine. Many mines are wet, and employees must wear rubber boots to remain at least partly dry, and even on relatively dry mines, some parts of the mines usually have water falling from overhead, there are accumulations of water, or the floor or other surfaces are wet or muddy, Some mines are dusty, and the air-borne dust quickly settles on the clothes and body of the miner, especially, when he is working in confined areas, or in places that are hot, humid, or poorly ventilated. Most occupations around a coal tipple, anthracite breaker, or a mill at a metal or nonmetallic mine have their own problems of cleanliness as to skin or clothes or both. Mining in any of its phases is inherently dirty work, and the employees dress accordingly while at work.In the early stages of mining it was the custom or workers to wear their dirty clothes home and change there. This necessitated their going home after work in dirty clothes which were usually damp from perspiration or from contact with wet or muddy matelials or surfaces, and, in addition to being inconvenient this was a frequent cause of colds, pneumonia, other pulmonary diseases or, possible skin ailments. Men working in very wet mines found that it was more satisfactory to change into dry clothes in the boiler room at the mine after work and allow their wet clothes to dry overnight. The mining companies later provided the first of the so-called ""dry-houses"" which were heated but had, few, if any, conveniences, such as showers, lockers, or latrines. The miners changed into dry clothes after work, but would not bathe or ""clean up"" until they reached their homes. Later, progressive mining companies provided bathing facilities for the employees, and eventually the present modern wash and change houses were evolved. Unfortunately, many mines, still have no bathing accommodations, and many have only makeshift accommodations."

Dec 1, 1947

By Graham W. Marks, RALPH MILLS, FRANK COSSEY

To determine the focal length of lenses or the performance of lens systems before mounting them permanently , it is desirable to have a device in which one or more lenses can be mounted easily and their positions relative to a light source and screen changed readily . We have designed and constructed such an optical bench and lens holder . The bench is similar to that of Houstoun5/ but has been modified , whereas the lens holder is , we believe , a new design .

Jan 1, 1948

By Robert J. Hundhausen, GEORGE M. GRISMER

This circular describes the methods and costs of deepening the Silver Summit three-compartment shaft in the Coeur d'Alene mining region of Idaho. A noteworthy rate of advance was achieved at this operation by the successful use of a mechanical shaft-mucking machine. The Silver Summit mine is 1 mile west from the town of Osburn, Idaho, via U. S. Highway 10. The adit-level portal of the mine is on the south slope of the Coeur d'Alene River Valley at an altitude of 2,700 feet. The Silver Summit shaft is 6,000 feet from the portal. In past years this shaft had been sunk from the adit level to a depth of 1,500 feet. During 1946 the Polaris Mining Co, deepened it to 3,095 feet. The work was done under a co- operative development agreement between the Silver Summit Mining Co. and the Polaris Mining Co.

Jan 1, 1948

By Robert J. Hundhausen

This paper describes the methods and costs of sinking a 2-compartment shaft at the Hope mine, Clark Fork, Idaho. The Hope mine is owned by the Hope Silver-Lead Mines, Inc. Albert E. Nash, of Clark Fork, is president and manager.

Jan 1, 1948

By C. L. Severy

On the Pacific coast during World War II, a tremendous ship-building industry was developed, Early in the war it became impossible to obtain in- got or steel scrap for ship ballast. Magnetite, an oxide of iron, was sub- stituted as it fulfilled the requirements of weight for available space in the ships. Consequently, a new use for the western magnetite was rapidly developed.

Jan 1, 1948

By Robert J. Hundhausen

This information circular is one of a series of Bureau of Mines reports dealing with mining and milling methods and costs . It describes the operations at the Little Pittsburg mine in the Pine Creek area of the Coeur d'Alene mining region near Kellogg , Idaho . The mine and mill have been operated successfully from 1942 to the present .

Feb 1, 1948

By McHenry Mosier

The Bell mine operated by the Warner Co. at Bellefonte, Pa., has an annual production of about 600,000 short tons of high-grade limestone. Since 1924, shrinkage stoping has been the mining method. Horizontal, long-hole diamond-drilling for production in stopes was started with one machine in July 1946. It is now standard practice. The burden on the holes is 10 feet. Diamond bits are noncoring EX-size in both concave and pilot types. The two types have little difference in drilling speed at the Bell mine. The diamond drills are mounted on 3-inch single-screw columns. Diamond drilling shows a marked increase in efficiency at the Bell mine, compared to percussion drilling, with respect to tons broken per drill shift, tons broken per foot of hole, and tons broken per pound of explosive. The advantages of diamond-drilling blast-holes also include (a) improved safety, greater footage per drill shift, (c) better frag- mentation of the broken, stone, and (d) reduction in amount of barring down required in stopes because the working places are limited to slots which have a relatively small area.

Feb 1, 1948

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

By A. B. Hooker

A list of permissible mine equipment approved by the Bureau of Mines prior to January 1, 1940, was published as Information Circular 7207.3 Three supplements published as I. C. 7240,4 I. c. 7283,2/ and I. C. 73166/ completed the list of equipment available to January 1, 1945. The present list is a revision of the previous lists, together with the additional equip- ment approved from January 1, 1945, to January 1, 1947. In preparing this list, certain items have been omitted, either because the manufacturer is no longer in business or manufacture was discontinued several years ago. However, some discontinued equipments that are still in service and for which repair parts are available are marked with an asterisk to indicate their limited status. The remaining obsolete equipments are listed in tabular form in Appendix 1. Appendix 2 lists seven satisfactory fuels available for use in permissi- ble flame safety lamps and shows where the fuels are available. The equipments listed were approved only when inspection and tests showed that they met the minimum standards of safety as outlined in "schedules" based upon laboratory tests as well as on performance underground. This circular is published so that users and potential users may be in- formed of the many types of permissible equipment available for reducing hazards incidental to coal mining and as an aid in identifying the equipments.

Dec 1, 1947

By McHenry Mosier

Diamond -drilling blast holes at Eastern Magnetite Mine C is proving economical in boundary shrinks , in removing pillars not readily accessible for percussion drilling , and in driving scraper drifts . The cost per foot drilled is greater than for percussion drilling , but savings in associated factors outweigh this handicap . The rocks drilled include trap rock and magnetite ore . The mining method is the panel , block- caving system utilizing scraper sublevel drifts instead of branch raises to convey the ore to the haulage level . Diamond -drilling blast holes was begun early in 1945. Three rigs equipped with noncoring bits are now in active operation two shifts per day . They are owned by the company , and the drill operators are paid by the day . In shrinkage stopes the drill is mounted on a horizontal bar set against opposite walls of the stope . Stoping holes are horizontal , which gives better results in blasting and requires fewer set ups . In scraper drifts the drill is mounted on a horizontal bar clamped to two columns about feet apart . Trim holes around the periphery of the drift and reliever holes are drilled 50 to 80 feet in length . A 10 - foot wedge cut drilled with a stoper is blasted in conjunction with a corresponding length of the trim holes to effect a 10 -foot advance of the full- sized drift . Recent drilling averages 97 feet per machine shift , excluding time utilized in setting up and moving the machine , hand mucking , and barring down . The feet drilled per bit at present is 417. These data represent the average for drilling in both rock (waste) and ore . Percussion drilling utilizes three types of wet drills . Detachable bits are standard . Gage changes for new bits is 1/8 inch and for reconditioned bits 1/16 inch . The life of a bit is five uses . Resharpening is on contract . A drill carriage is used in haulage headings .

Feb 1, 1948

By G. W. Groove, E. E. Quenon

"INTRODUCTION Uncontrolled mine fires originating in exposed coal beds through the acts of careless or irresponsible persons present a serious threat to buildings, surface property, and the life and health of persons near the affected area. Apparently, the seriousness of such fires is not fully understood by property owners or those residing in the vicinity, as practically nothing has been done to alleviate conditions. In many instances, such fires have been active for several years before property owners or civic organizations have shown any interest toward having the fire extinguished. Recommendations by Bureau of Mines investigators in the interest of controlling such fires are seldom followed, as the Bureau cannot provide the funds for doing the work.Several uncontrolled and widespread fires are burning along the outcrop of coal beds and in underground abandoned mine workings within a 25-mile radius of Pittsburgh, Allegheny County, Pa. If these fires are permitted to continue to burn unabated, the ultimate results may be far-reaching. Most of the outcrop fires investigated are believed to have originated from burning rubbish, forest fires, or workmen, hunters, or others building fires near the outcrop of ,the coal beds. In other instances, smoke and fumes have suddenly appeared in the vicinity of abandoned coal-mine openings, indicating that a fire has either burned its way along the outcrop of the coal bed or has traveled through the abandoned mine from another location. An underground or outcrop coal-mine fire will be very likely to continue to burn as long as an oxygen supply is present.; and, so far as is known, such fires do not stop burning automatically until virtually all combustible matter is consumed."

Feb 1, 1948

By M. J. Mechling, H. J. Sloman

"INTRODUCTION The practicability of providing safer methods of underground transportation for mine workmen and officials has been given much thought in recent years by advocates of safety, health, and efficiency. Numerous fatalities and disabling injuries have resulted from falls of roof, personal contact with both electrical conductors and timbers, and improper position or conduct of passengers while they were in man-trips. Unfavorable atmospheric exposure due to high-velocity air currents and sudden changes in temperature may adversely affect the health of mine workmen if they are transported in unprotected Cars.Recent installations of protected, man-trip cars, wherein such cars have been utilized to haul men to and from their stations in the mine, have resulted in a large reduction in exposure to haulage hazards. Where special-built cars have been used the probability of injuries to men during transportation in man-trips has been decreased, and the morale of the employees has been improved. A number of man-trip cars are in service in the coal-mining regions; those described in this circular are typical examples of a few installations."

Feb 1, 1948

By J. H. East, D. Harrington

"INTRODUCTION Shaft mines, coal and noncoal alike, have a common hoisting problem that remains largely unsolved - how to obtain a mechanical device that will suspend a cage or skip in a mine shaft if the hoisting rope should break or become detached from the cage or skip and that will function effectively under all conditions of service. Safety catches, or safety dogs, as they are commonly named, are installed on nearly all mine cages and many skips operating in American mines, but often, if the hoisting rope breaks, the cage or skip falls to the bottom of the shaft in spite of safety devices, causing much property damage and often fatalities.Available information relative to safety catches for mine cages and skips, desirable characteristics of safety catches and methods of testing safety catches to determine whether they are functioning correctly has been assembled in this publication for the convenience of those responsible for the safe operation of mine cages end skips and, more particularly, to focus attention on the need for a device that actually will stop and suspend a falling cage or skip under all conditions of use and do it without killing or maiming the occupants."

Feb 1, 1948

By J. H. East, D. Harrington

"INTRODUCTION Burning refuse dumps are a common and by no means pleasant sight in most coal-mining distracts; they have been and largely continue to be accepted as a necessary, if undesirable, adjunct to coal-mining operations. The odor, smoke, and fumes emanating from the burning dumps have caused much property damage, as well as aroused unfavorable public sentiment in the areas thus affected; and there is reason to believe that, in at least some cases, they have had an adverse effect on the health of certain communities, adjacent to mines. In some instances such communities have been owned or controlled by the mining companies and in others they are incorporated towns.After the start of World War II, it was necessary for Great Britain to take prompt and effective measures to extinguish or at least blanket the burning refuse dumps at collieries, since the fires served as beacons for the enemy planes; the problem thus became a matter of national security rather than one of local inconvenience. If the United States should become involved in a bombing war, these dumps might became a source of national danger, hence now is a propitious time to at least make a start on available methods of solving this problem. Much progress was made in Great Britain in extinguishing the dump fires that had burned for years and in preventing newly made dumps from taking fire.Burning refuse dumps have not been a national problem in the United States, but they are a nuisance and frequently a danger and often a fruitful cause of poor public relations on account of the odor and fumes. Many progressive coal-mining companies are taking effective and positive action in trying to extinguish old dump fires and to build new dumps so they are less likely to fire.The purpose of this paper is to provide information about the problem as well as on ways to extinguish refuse dump fires, to describe methods of constructing dumps that probably will prevent them from firing, and to point out some of the danger that exists when dumps are improperly built and when they are on fire."

Mar 1, 1948

By THEO L. JOHNSTON

In preparing for war , Japan built an iron and steel industry that ranked high with other industrial nations . Deficient in raw materials for making iron and steel , it had to acquire the bulk of its iron ore and much of its coal and scrap iron from foreign sources . Steel manufacture, and fabrication , however , were reserved mostly for the Home Islands , where modern integrated plants produced the implements of war . The vulnerability of relying on imports during the war was recognized early, and steps were taken to exploit iron-ore deposits and develop treatment processes on the Home Islands in order to be as self - sufficient as possible . Although the industry had expanded considerably, the capacity of the large plants still was insufficient for military requirements, so other meth- ods of producing iron and steel were adopted, which in some ways illustrate the desperate effort made to supply the war machine. In developing the iron and steel industry, modern practices of other countries were studied and followed with modifications to suit Japanese con- Aitions. German and American technical ability and equipment played a large part in the program; however, the Japanese had competent furnace technologists capable of obtaining proper equipment performance. For the most part, the standard practice consisted of smelting iron ores in blast furnaces and then refining the pig iron to make steel in open-hearth furnaces. Electric furnaces played an important part, especially in the manu- facture of alloy steels. Various other methods yielded minor but significant production. Among the various other treatment processes used, the production of sponge iron in rotary kilns 'probably was the most important in producing melt- ing stock for steel making. Of special importance was the fact that sponge iron made from low-grade ores contained critical metals, such as nickel and chromium, so that the results were more significant than was generally believed.'

Mar 1, 1948

By H. H. Schrenk, L. B. Berger

"INTRODUCTION The Bureau of Mines frequently receives requests for information and advice regarding the equipment necessary for establishing laboratories for the analysis of mine atmospheres. Such requests are made by mining companies, State mining departments, and other agencies concerned with the safety of mining operations. In many instances it is desired to install a complete laboratory, which will necessitate purchase of suitable gas-analysis apparatus and all the minor but important accessory equipment needed to carry on this type of work. Although publications that describe methods and techniques applicable to the analysis of mine atmospheres are available, it is not within the scope of such publications to give detailed information on laboratory equipment or design. Persons unfamiliar with laboratory practices and gas-analysis procedures may find it difficult to decide upon the proper equipment for their particular needs and to itemize the various accessories that must be obtained to set up a complete laboratory.The purpose of this circular is to discuss the different types of equipment that may be used in the analysis of mine atmospheres, with particular regard to the application and limitations of each type. Information on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres is given also, and suggestions on laboratory design are included. As much of the necessary equipment may be obtained from laboratory supply houses, the information should aid in arriving at estimates of the cost of proposed laboratories.The procedures involved in the analysis of mine atmospheres are not described; such information is contained in publications referred to in this circular."

Feb 1, 1948

By W. H. Young, R. L. Anderson

"Physical conditions, such as thickness and character of the coal seam, dip or pitch of the seam, depth of cover, character of roof and overlying strata, mine water, etc., affect the productivity in bituminous-coal mining. Thickness of the coal seam being mined is probably the most important single item that determines whether the output per man per day shall be low or high; however, in strip mining the depth of cover or overburden to be moved is of equal importance.Bituminous coal is mined today from seams of exceedingly variable thickness - less than 2 feet to more than 50 feet; however, a large majority of the mines are producing .coal from seams 3 to 6 feet thick. The average thickness of the coal seams mined in the United States has not changed materially in the past 25 years. The average seam thickness for all bituminous-coal mines was 63 inches in 1920 4/ and 65 inches in 19)45. As thick seams have been exhausted in the older fields, other thick seams, have been opened in the newer fields.Productivity increased from 4 net tons per man per day in 1920 to 5.78 in 1945. This 45 percent increase in productivity resulted from increased mechanization. The percentage of underground production represented by coal cut by machines increased from 61 in 1920 to 91 in 1945 Mechanical loading increased from less than 1 percent of underground production in 1920 to 56 percent in 1945, and strip mining increased from less than 2 percent to 19 percent of the total production during the same period."

Dec 1, 1947

By H. D. BAILEY, John W. Cole

This paper is one of a series on mining methods and costs published by the Bureau of Mines .. Because of the role, played by the Federal Government in the discovery of the ore body, a description of the exploratory operations of the Bureau of Mines, is included ...

Apr 1, 1948

By H. H. Schrenk

One phase of Bureau of Mines work in health and safety, is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks, supplied-air respirators (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks),2 dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch, approval tests of other types of respira- tory protective equipment are conducted by the Health Branch, These branches are in the Health and Safety Division.

Mar 1, 1948