Search Documents

By George K. Clement

Manual estimating method through use of equations, factors and curves for preparation of feasibility type estimates for capital and operating cost of mining and primary beneficiation in the United States and Canada of various types of minerals occurrences, except fossil fuels, using state-of-the-art technology. User should have basic estimating experience in the mining industry and/or related fields. Primary usage of this handbook will be for the preparation of preliminary estimate within a reasonable degree of accuracy with relative small amounts of hard input data. Output may be used to determine if a more finite type of estimate should be produced.

Jan 1, 1978

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By D. A. Paice

A power supply to operate fluorescent or mercury vapor lamps from 300 volt dc coal mine trolley wires has been developed for the Bureau of Mines. A high frequency regulated inverter unit incorporates ballasts for a mix of lamp loads up to 650 watts. For 600 volt trolley systems an additional power converter unit was developed to step down the dc voltage to 300 volts for the inverter unit. Both units have operated in a working coal mine for over 12 months without need for servicing. The lamp load in these tests included two 100 watt mercury vapor head lamps and six 75 watt fluorescent lamps.

Jan 1, 1979

By Tim F. Dyson

Feasibility of employing automated processing and detection techniques in the mine disaster communications problem is demonstrated. Efficient processing methods are developed. These methods have been demonstrated both in a laboratory and in a field environment. Evalua¬tion of existing computer capacity is given along with recommendations for expansion.

Jan 1, 1981

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By Jeffrey P. Schubert

The study site in northeastern Illinois underwent surface mining for coal in 1943 and was reclaimed by the state of Illinois in 1972-1973. Additional soil amendments and seed were applied to the spoil surface in 1975-1980. Previous studies in 1975-1978 had shown that the surface spoil materials and five final-cut lakes at the site were quite acidic and the lakes contained high concentrations of sulfate and dissolved metals. Surface runoff water from monitoring plots in 1976 were only moderately acidic and the mean concentrations of most dissolved metals and sulfate in the runoff waters were less than 25% of the concentrations found in Lake B. By 1980, vegetation had become well established over most of the mined area. However, the five final-cut lakes (Lakes A-E) remained acidic. The purpose of the study reported here was to determine the physical and geochemical subsurface conditions of the spoil materials, the hydrologic flow system within the spoils, and the magnitude of acidic spoil leachate migration into the lakes and into the wetland prairie north of the mine site. Lakes A, B, C, and E were still very acidic in 1980-1981 (pH range: 2.9-3.4; aridity range: 110-860 mg/L as CaCO3). Lake B had the worst water quality, with mean concentrations of dissolved aluminum, iron, manganese, and sulfate of 75, 25, 37, and 3340 mg/L, respectively. Shallow groundwaters in spoil materials around Lake B had a lower pH and about two to four times greater concentrations of aridity, aluminum, manganese, zinc, and other metals and nearly 20 times greater dissolved iron than the water in Lake B. The shallow groundwaters in undisturbed soils and bedrock 10-30 m north of the mine site spoils generally were alkaline, but did contain occasional moderately high sulfate and metal concentrations. Pumping tests and recovery tests conducted in piezometers showed hydraulic conductivities of spoil materials ranging from less than 10- to 10-5 m/s; hydraulic conductivities of natural soils and bedrock were measured between 10-10 to 10-7 m/s. Water levels in spoil materials increased rapidly in response to rainstorm events and the recession curves were relatively quick to decline, lasting only two or three days. Quick infiltration of rainfall into the spoil surface and percolation down to the water table caused a rise in groundwater levels and movement of spoil groundwater into the lakes. This groundwater component in the lake water budgets could account for most of the water quality problems occurring in the acid lakes.

Jan 1, 1984

By Timothy J. Rohrbacher

This report presents results from an ongoing U.S. Bureau of Mines study defining domestic coal reserves. Examinations of five 7 ½ -minute central Appalachian quadrangles have been completed to date. Only 26.4%, 5.0%, 6.5%, 8.2%, and 4.2% at the coal resources remaining in the Matewan, Boltsfork, and Hoskinston, KY; Vansant, VA; and Beckley, WV quadrangles, respectively, constitute economically recoverable reserves. An evaluation of the coal mining industry's impact on the economy of Pike County, KY, wherein the Matewan quadrangle is located, was also completed in order to provide a basic understanding of the influence of coal mining on the local economy. Results show that coal mining is the only major income producing industry in Pike County, accounting for about 46% of the county's income, and 21% of the total available employment, in the base year 1990. If similar results are found in subsequent investigations, a strong argument can be made that traditional coal producing regions may soon be experiencing resource depletion problems far greater and much sooner than previously thought. This will affect not only the coal industry but, given the obvious dependence of Pike County's economy on its coal mining industry, the entire social and economic infrastructure of large areas.

Jan 1, 1994

VOLUME I Volume I of this three-volume report is the result of development of a comprehensive, coordinated approach to site data-acquisition activities to produce key plans and reports during the evaluation and development of a surface coal mine. A logic diagram illustrates activities in the planning and decision-making process from exploration through post-mining monitoring. The report briefly discusses major elements, other than the site environment, which influence development of mining and reclamation plans and refers to other readily available literature for details outside the scope of this study. The essence of the rationale is shown to be the 1 employment of necessary skills at the proper time to evaluate specific data ' requirements and integrate them into a cost-effective program to produce initial and major feasibility reports, mining, and reclamation plans, and the environmental impact assessment.

Jan 1, 1976

By Normal Seidle

This report (rind related Appendices) provides a description of the functional design specifications and related rationale for development of a training system for dragline equipment operators. Phase I activities involved a delineation and detailed analysis of specific behavioral requirements for successful dragline operation. Following the field data collection effort, job/activity/task descriptions were formulated into training requirements which can be achieved by a trainee with training hardware having specific functional capabilities. The training system analysis integrated the training requirements and the trainer functional capabilities into recommendations which configure a total training system. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1975

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

VOLUME II Volume II, in conjunction with Volume I, is a general guide to the selection of cost-effective methods of site data acquisition in all geologic environmental, and socio-political circumstances. The judgement of a generalist or trained specialist must be relied upon in the final analysis to design the optimum program for a specific site.

Jan 1, 1976

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

VOLUME III The objective of Volume III of this report is to provide a concise review of six major types of legal constraints, controls, and regulations on surface coal mining in the United States, as of January, 1976. At the same time, an attempt is made to format the details of federal and state exploration, mining, and reclamation regulations such that point-by-point comparisons can be made and updated as revisions occur. Thus, Volume III should provide both an executive overview and a user's manual of legal controls of surface coal mining.

Jan 1, 1976

By Peter Murphy

This report (arid related appendices) provides a description of the functional design specifications, engineering design specifications, and program of instruction for development of a training system for dragline equipment operators. Based upon a task analysis and training system analysis prepared under Phase I, Phase II efforts expanded upon and refined the functional design specifications. The training hardware components have been developed to a point shy of system fabrication. A detailed outline of the porgram of instruction and content sequence has been prepared. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1976

By G. Ahnell

Throughout portions of four (4) heavily mined Appalachian states subdivided by the Mine Safety and Health Administration (MSHA) as: District 3 -Northern West Virginia and Maryland; District'" -Southern West Virginia; District 5 -Virginia; and District 6 -Eastern Kentucky, active coal mine waste embankments associated with mechanical and/or chemical coal processing facilities of various levels of coal preparation were inventoried. For each site plant specifications, disposal techniques, embankments' characteristics, and coal source data were accumulated. Mapping at 1: 24, 000 and 1: 250,000 scale and Disposal Site Characterization forms were developed to present the findings. Associated abandoned surface and underground openings near each site were also indicated as well as locational data for each site and the areas environmental conditions - temperature, precipitation and vegetation types. A state-of-the-art review of coal preparation, waste disposal, and alternative uses of coal waste is also included.

Jan 1, 1982

[Module 10. Internally Cued Operating Contingencies Prerequisite: Modules 1-7 - Estimated Instructional Time: 2.42 hrs. Module Abstract Trainees, using programmed instruction, describe the cues, consequences, operational sequences, and possible causes resulting from loss of air pressure from power fluctuations, and from a failure of the automatic lubrication system. Although some of the contingencies may be initially signaled by an alarm or from the oiler, each trainee will demonstrate proficiency in the appropriate operating techniques and procedures. This module also includes a review component for those trainees identified in the assessment exam as requiring less detailed instruction.]

Jan 1, 1976

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

By Kent W. Hawley

An improved visibility system was developed for use on the large (100 ton+) haulage trucks typically operated in open pit and surface mines. The improved visibility system provides the truck driver' with a means of viewing hazardous situations that occur in the extensive blind areas adjacent to his true. The cost effective, reliable, visibility system consists of a closed-circuit television three unique fresnel viewers, and two improved mirrors. This report describes the visibility problems of Large trucks in the surface mining environment, shows the performance of existing mirrors, substantiates concept selection, and describes the prototype improved visibility system.

Jan 1, 1978

By Harold J. Miller

Loading and haulage of run-of-mine ore is frequently the highest cost in underground mining operations. These costs can be significantly reduced by use of belt conveyors, a common practice in coal and similar soft miner ii mines. This is particularly true if oversize ore and rock can he eliminated prior to conveying; thus producing a demand for crushers near the production areas. Portable feeder-breakers are extensively used in conveyorized mines, but no suitable, equivalent equipment, is available to provide these benefits to hard rock mines of low to medium headroom. A hard rock crusher capable of easy movement and readily disassembled would allow use to belt conveyors and could improve the general safety and productivity of any underground ore hauling system. This report summarizes proposals and findings made in conjunction with the newly designed M-44 Low Head Portable Crusher which is believed well capable of meeting the requirements of a "portable, underground, hard rock" machine as previously defined in earlier reports. Data gathered by use of the 1/4 Scale Model of the M-44 has substantiated and verified the concept sufficiently to justify construction of a full-size machine for further testing under actual mine conditions.

Jan 1, 1978

By John L. Dahle

This report documents the research efforts that were undertaken to design, install and test noise abatement devices for use on off-highway haul trucks operating in surface mines. The objective of the program was to reduce the environmental noise from haul trucks. The noise reduction devices that were developed utilized existing technology and were tested on a 50-ton haul truck. The efforts emphasized the reduction of noise emitted from the engine compartment which included the use of side shields, sound absorbing material, improved radiator shroud design, and a modulating clutch fan. Noise tests were conducted using modified SAE test procedures for measuring sound levels around a stationary and moving machine, and inside of the operators compartment. Test results showed a maximum of 4 dB(A) reduction measured 16 feet from the truck. Interior cab noise was reduced 6 dB(A) with the windows and vents closed.

Jan 1, 1983