Search Documents

By L. H. Wullstein

Nitrogenase activity (C2H2 reduction) was found to be associated with the following grasses in the field: Agropyron dasystachyum, Agropyron smithii, Aristida purpurea, Oryzopsis hymenoides and Stipa comata. Uptake of fixed nitrogen was also demonstrated for these grasses. Two unidentified nitrogen fixing bacteria were isolated, one from Stipa comata and one from Aristida purpurea. Cynodon dactylon and Agropyron cristatum were successfully inoculated with the unknown isolate obtained from Stipa comata. The inoculated plants exhibited nitrogenase activity (C2 H2 reduction) whereas uninoculated controls gave negative results.

Jan 1, 1982

By Otto Robert Stein

Erodibility of reclaimed surface mine soils is a subject in need of quantification. Effects of soil erosion from reclaimed areas may damage surrounding areas and the quality of water in nearby streams and lakes. It may also reduce the potential productivity of the reclaimed site. A study was conducted to determine erodibilities of different reclamation treatments and a nearby unmined soil at three Indiana strip mine sites. A rainfall simulator was used to artifically erode plots con¬structed within seven treatment categories and the unmined soil. Soil erodibility was assessed in terms of the Universal Soil Loss Equation (USLE) K factor. Values for K calculated from field data were compared to values predicted from independently measured soil properties. Differences in soil erodibility between treatments were site specific. Unmined soil had the highest calculated erodibility at one site but at two other sites soils having reclaimed A horizons were highest. Shaley overburden treatments had the lowest calculated erodi¬bility. Predicted soil erodibility was usually lower than that calcu¬lated from field data. Site specific slope gradient factors (S) were developed for reclaimed A horizon treabnents. This was done because the USLE S factor overestimated the measured soil loss at steeper slopes.

Jan 1, 1983

By D. T. Hahn

Adequate and cost effective erosion control is an important component in most plans for reclamation of surface mined land. Despite the fact that much is known about erosion of agricultural lands, insufficient conclusive knowledge is available about erosion of reclaimed surface mined land. Our study was conducted to characterize the erodibility of reclaimed surface mine land relative to unmined cropped land, and to evaluate the accuracy of the universal soil loss equation (USLE) in estimating erosion from reclaimed soils. A rainfall simulator was used to measure runoff and erosion rates from plots at three Indiana surface mines. The relation of erosion of the reclaimed soils was not completely constant with that from the cropped soils. Significant differences in erodibility were observed between reclaimed and nonreclaimed top soils, as well as reclaimed topsoils and reclaimed subsoils.

Jan 1, 2011

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982

By Ginger S. Evans

This report documents a preliminary hydrologic investigation of an area where longwall mining methods are to be used. The scope of work includes: determination of physical and chemical characteristics of major soil types in the area; determination of physical and chemical properties of surface water bodies; collection of geologic characteristics, including stratigraphy, structure, and detailed aquifer descriptions; collection of 10 years' meteorological data and installation of a weather station; and a detailed ground-water investigation that includes completion of observation wells, aquifer testing, water quality sampling, and analysis using a 3-D computer model. The Trescott model developed by USGS was used to simulate steady-state aquifer conditions. Input data from 8 multiple-completion monitor wells were used to model an area of approximately 10 square miles. Two layers, coal and overburden, were simulated, both confined. Model results showed good agreement with know piezometric data, desaturated areas, and flow from springs. The study area was found to have very low-yield bedrock aquifers with transmissivities ranging from 5 to 320 ft2/day for the coal (depths from 500 to 1,200 ft) and from 499 to 576 ft2/day and fractured sandstone units (depths less than 100 ft). Annual precipitation and recharge are very low, 10 to 11 inches and 0.25 inch respectively. The area has very high relief and large areas of rock outcrop. No perennial streams are present on the site.

Jan 1, 1983

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By King K. Mak

The objectives of this study are to: (1) Assess current signing regulations and practices; (2) Develop effective signing guidelines; and (3) Evaluate the applicability and appropriateness of the proposed signing guidelines through field demonstration at representative mines. A literature search was conducted to determine the state of the art for signing applicable to surface mine haulage roads as well as survey of existing MHSA regulations and review of MSHA accident records. Nine representative mines were visited to gather information on current signing practices. Preliminary signing guidelines were then developed based on the abovementioned data. Field demonstration of the preliminary signing guidelines was conducted in which signing programs were implemented in two selected mines. Signing requirements were first assessed at each of the two participating mines. Subsequently, the necessary signs were designed, purchased, and installed at the two mines. Evaluation of the signing program as to its adequacy, appropriateness, and effectiveness was solicited from both mine management and operations personnel. Experiences gained from field evaluation were then incorporated into the final signing guidelines as presented in this final report.

Jan 1, 1981

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

By James L. Fenton

In its unending search for the raw materials that the affluent society of today requires the mining industry has found it necessary to go to great depths, in many cases, to produce these materials. Inherent with this problem is the insufficient technology relating to improving extreme environments that the mine personnel are exposed to. In this dissertation, the sources of heat flow into a mine along with the various effects that this heat has on the mine personnel are investigated. The object of dissertation is to compile all the available published information pertaining to these underground heat and their effects into one paper. This will provide the mining industry with an available easy-to-use to aid in the determination of mine ventilation requirements as the mines are in the phases of original planning or being extended to depth. Areas of significant, deficiencies it knowledge have been disclosed during this overall appraisal. Recommendations on important basic research needs are out lined for future consideration by Federal or industries sponsorship. This thesis should serve as a stimulus lo, future well-organized research efforts in the area of underground heat sources and their control.

Jan 1, 1973

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By Paul L. Michael

Roof warring signals from eleven underground coal mines (principally in the Pittsburgh seam) were studied and analyzed. The character of individual acoustic warning signals is shown to be dependent on spectral distribution of energy. Reverberation tires (pulse decay rates) were found to be usually between 0.1 and 0.5 seconds. Listening tests were conducted to assess the miner's ability to discriminate speech and roof talk signals in noise and in quiet, with and without ear protectors and with various levels of hearing loss. The ability to detect roof talk is shown to be generally degraded while wearing car protection in quiet, although, if car protectors are worn only when required by high noise levels, the ability to detect roof talk will be preserved at its maximum.

Jan 1, 1972

The purpose of the contract was to develop an improved coal mine dust sampler whose electrical-to-mechanical energy conversion efficiency would be superior to that of the presently available equipment. The electrical to (pressure) X (volume) conversion efficiency directly affects the size and weight of the air samplers. At least half of the mass of present equipment is composed of the rechargeable batteries. Any increase in efficiency will allow this mass to be reduced or the flow rote to be increased.

Jan 1, 1974

By Peter G. Groer

The commonly used exact methods (1-2) to determine the WL measure the total a activity or the total number of a counts during three preselected time periods. Due to the half-lives involved (TRaB = 26.8 min, TRaC = 19.7) I these methods take 3S minutes to complete the a activity Ra measurements. Methods using the total a counts, obtained at times less than about one RaB half-life after the end of sampling run into statistical 214 problems. These methods are almost blind to RaB (Pb214) as a consequence of its relatively long half period (see above) and the fact that RaB is a ß emitter. The way out of this dilema is to measure RaB directly through its ß activity. Since RaB's daughter Rae (Bi214) is also a ß emitter, the two f3 spectra have to be separated to obtain RaB alone. How this is accomplished 1s described in subsequent sections describing the theory of the IWLM and its calibration. 2.0 THEORY The IWLM samples air for two minutes and counts this airs ample for two minutes starting 3 sec after the end of the sampling period. The instrument has three channels. The lower a channel, the upper a channel, and one ß channel. The total RaA counts observed are accumulated in the lower a channel, the total RaC? counts are stored in the upper a channel. The total ß counts from RaB and RaC are recorded in the ß channel. These three quantities are functions of NA, NB, and NC, the unknown concentrations

Jan 1, 1975

By Klaus L. Cappel

In 1972, the Bureau of Mines of the U. S. Department of the Interior commissioned the development and design of a Simulator for research and testing of mine roof supports used in long-wall mining. The purpose of the Simulator is to reproduce forces and displacements of a section of a mine roof in contact with one or more supports. This report is an account of the design process that resulted in the final configuration of the Simulator presented here. It includes discussions of engineering considerations that led to major changes in important details of the Simulator. These changes, however, did not substantially alter the basic design originally proposed, except for the elimination of certain originally-specified features that were adjudged as insufficiently cost-effective by both the Bureau of Mines and the design agent at an intermediate stage of the design.

Jan 1, 1974

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By Marilyn Biviano

(l)The direct economic costs to this nation resulting from a decision to embargo South African strategic and critical minerals imports are estimated at $1.85 billion per year.2,3 About 94 percent of these estimated costs are for two platinum-group metals (PGM's), platinum and rhodium. The estimated costs of a 5-year embargo beginning in 1988 for the strategic and critical minerals analyzed are presented in Table 1.4 (2)There are sufficient alternative world sources to South Africa for manganese, chromium, palladium, titanium, and vanadium to meet U.S. industrial demand in the event of an embargo. (3)Alternative world sources to South Africa for platinum and rhodium cannot meet U.S. industrial demand. Non-South African world supply sources can meet about 40 percent of domestic platinum consumption requirements and 50 percent of rhodium requirements. (4)As a result of the increase in prices for platinum and rhodium during the embargo, expansion of domestic platinum-group metals mining and secondary production is expected. During a five year embargo, domestic primary and secondary production expand and together satisfy about one-third of U.S. platinum requirements, one-third of U.S. rhodium requirements, and over one-half of domestic palladium requirements.

Jan 1, 1988

By James C. Barker

Yttrium and rare-earth element. pegmatite dikes are associated with a peralkaline granitic and nephelene syenite complex near Dora Bay on southern Prince of Wales Island. Mineralized dikes were mapped and sampled during USBM investigations in 1987 and 1988. Coarse-grained pegmatite dikes, which emanated as late-stage magmatic fluids from the intrusion, further evolved into vein-dikes and ultimately silica-rich veins. The dikes can be traced up to two miles along a north-south zone. Lithophile elements exhibit a pronounced zonation in vein-dikes and veins that are distal to the Dora Bay complex with increasing values correlating with increasing distance from the complex. The pattern of mineralization suggests very late stage magmatic fluids containing the incompatable lithophile elements were injected into a preexisting north-south fracture zone. REE mineralogy exhibit fine-grained intergrowths of principally thalenite and bastnaesite with lessor monazite and eudialyte. Euxenite contains most of the columbium values and zircon is commonly associated with the dikes. Estimates of inferred and hypothetical resource tonnage range from 1.7 X 1C6 to 8.5 X 106 st for two deposits. Contained RED (including yttrium) averages 0.5 pct and ranges up to 2.0 pct. Deposits are of polymineralic composition and about half of this resource comprises the heavy yttrium subgroup.

Jan 1, 2011