Search Documents

By Cheryl Hill, Michael Keane, Pamela Mike, Raghoottma Pandurangi, William Wallace, Mohindar Seebra, Val Vallyathan

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte bemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz and kaolin dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect of lecithin adsorption. Dust hemolytic potential versus medium pH is presented. Fourier transform infrared spectroscopy and photo-acoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis. INTRODUCTIONQuartz dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction.In the alveolar ·spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, among other functions, mechanically stabilizes the lung from collapse by reducing the surface tension of water in the alveolar sacs.1 This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11 % in dog lavage fluid), and phospholipids (about 88%).2 Pbosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalmitoyl lecithin (DPL).2 Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occurring upon deposition of a particle in a pulmonary alveolus. As may be seen from Figure 1, the DPL molecule has several fixed charges at neutral pH; a positive charge on the trimethylamine (choline) moiety, and a negative charge on the phosphate group. Also evident are the two fatty acid residues of palmitic acid, which are bonded through ester likages to the glycerol segment of the molecule. The fatty acid moieties of phosphatidyl choline make the molecule inso1uble in aqueous solutions under normal conditions, but a colloidal unit of aggregated molecules called a micelle is usually formed spontaneously above a certain minimum concentration. Small micellar vesicles are generally formed in the laboratory by using ultrasonic agitation or by solvent evaporation methods."

Jan 1, 1990

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

"We have reported previously that crushing or grinding crystalline silica results in the generation of silica-based radicals on the particulate surface and that these radicals can generate hydroxyl radicals in aqueous solution. Data in the present study indicate that freshly ground silica is more cytotoxic and is a more potent activator of alveolar macrophages than comparably sized aged silica. That is, compared to aged silica, fresh silica is 4.2-fold more potent in decreasing the membrane integrity of macro· phages; is 50% more potent in activating hydrogen peroxide secretion by macro· phages; and is 4.frfold more potent in stimulating cellular chemiluminescence. Prosil 28, an organosilane material, is an effective coating agent for fresh silica. It decreases the cytotoxicity of fresh silica by as much as 78% and decreases the ability of fresh silica to induce chemiluminescence from alveolar macrophages by 58%. The data suggest that surface radicals associated with freshly cleaved dust may be an important factor in the induction of pulmonary disease. Furthermore, treating dust with coating agents may substantially decrease toxicity. INTRODUCTIONThe U.S. Department of Labor estimates that over 1.25 million American workers may be exposed to crystalline silica and that nearly 60,000 may be at risk of developing some degree of occupational lung disease (Parkes, 1982; Peters, 1986). Occupations of concern include miners, stone quarry workers, sand and gravel workers, sandblasters, foundry workers, and glass workers. Acute silicosis is characterized by inflammation, alveolar lipoproteinosis, and the rapid development of respiratory disability (Banks, 1986). In contrast, chronic silicosis develops 20-40 yr after initial exposure and is characterized by the appearance of concentric hyalinized nodular lesions and the progressive development of dyspnea (Parkes, 1982; Ziskind et al., 1976)."

Mar 1, 1992

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

The twelve latexes listed in Table XI penetrated A horizon soil as shown by elution through a laboratory soil column and gave good sealing efficiency. See details in Table XII. High elution through laboratory soil columns of 4 to 6 inches depth is desirable because it predicts penetration of latex to a greater depth in the field. No definite correlation was evident between penetrating ability and particle size, surface tension, or pH. Most of the materials, however, were characterized by low surface tensions in the 36 to 53 dynes/cm range while particle sizes were usually in the intermediate range of about 1500 to 2500 Å. Naugatex J-3471 (a highly crosslinked styrene-butadiene copolymer) was the most promising of this group for stability, penetrating ability; and sealant efficiency. It also showed utility with [B] profile soil. Many of the other latexes tested in this investigation showed good sealing efficiency but were judged unsatisfactory because they gave low penetration or formed surface films with & horizon top soil. In general, latexes containing cationic surfactants were not satisfactory because they formed a heavy surface film. This is due to neutralization of the positive latex charge by the negatively charged soil particles.

Jan 1, 1972

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators&apos; shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators&apos; duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators&apos; noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

Lower noise exposure levels for operators and cleanup personnel working in portable nonmetallic mineral crushing and screening plants.

Jan 1, 1983

Reduce permanent hearing losses to bulldozer operators. Approach Two types of noise control packages have been developed, that can be readily fabricated and installed into bulldozers by mine personnel. How It Works Both of the noise control packages reduce the noise exposure of the operator by two techniques, blocking the noise paths or absorbing the sound before it reaches the operator. Both airborne noise paths and noise paths through the machine are blocked. One noise control package is designed for bulldozers having ROPS (Roll Over Protection System), but no cab. The other package is designed for bulldozers having ROPS

Jan 1, 1981

By J. J. Forbes

Problems connected with the incidence, effects, determination, and control of dusts are still much before the public, although more information is available to the layman than when Bulletin 400, of which this publication is a revision,5 was issued in 1937. Bulletin 400 attempted to assemble information in convenient form on various phases of the dust problem, largely in the mining and allied industries. This revision includes data that have accumulated since 1937 and some that appeared previous thereto but were not available to the authors at that time. The literature on this subject is so voluminous that no attempt has been made to include all published material or all types of dust diseases, but only to assemble some of the more outstanding data on several aspects of the subject.

Jan 1, 1950

By D. Harrington

Dust diseases are much before the public at present, but little reliable information on the subject is readily available to the layman; even those rated as experts usually have a more or less theoretical conception of these diseases, their causes, remedies, and prevention. Until recently little attention has been given to prevention, and the usual attitude of the engineer, upon whom the main reliance for prevention ultimately must devolve, has been to let "sleeping dogs lie" or, more definitely, to "let well enough alone." However, the "laissez faire" attitude no longer is tenable; in the past few years numerous conditions have caused those engaged in industry, including mining, to study the subject with a view to ascertaining the facts upon which to formulate remedial measures, primarily preventive. This bulletin is an attempt to assemble information in convenient form on effects of breathing dusts, largely in the mining and allied industries. The literature on this subject is so extensive that no attempt has been made to include all published material or all types of dust diseases but only to assemble some of the more outstanding data on several aspects of the subject, especially with reference to silicosis.

Jan 1, 1937

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

By Rollien R. Wells

A REPORT of technological advancements restricted to a specific 12-month period is impractical. Inherent in the nature and development of technology is the element of time; rarely can a new process or product be attributed to a particular year. An overall picture of general trends and pattern changes, however, is indicative of technological growth. This paper presents selected observations and discussions of current metallurgical research and practices in an attempt to develop&apos; such a picture. Of the estimated $16.5 billion spent for research and development in the United States in 1962, at least 80 percent was earmarked for the aircraft, electronics, chemical, and machinery industries. Much of the effort was of the end-use variety and was oriented closely to the national defense and aerospace programs. Only a small fraction of the total research money was directed to studies of the utilization and improvement of metals. Even if the investigations in allied fields such as solid state physics are included, the total research expenditure for metal and mineral materials barely reached $500 million. An additional $200 million was spent by industry and government for development of minerals recovery and processing methods.

Jan 1, 1963

By Kenneth B. Higbie

PRESIDENT LYNDON B. JOHNSON announced at midyear that the test flight of the A-It plane, the world&apos;s first super-sonic aircraft capable of flying 2,000 miles per hour, was made possible by "the mastery of the metallurgy &apos;and fabrication of titanium." Not all of the contributions made by the mineral industry in 1964 were acknowledged so widely. Yet the contributions were significant as the search continued for new and improved methods for providing metals and mineral products to meet the ever-expanding requirements of the world economy. This chapter reviews only a few of the metallurgical developments that resulted from U.S. and foreign research efforts. MINERAL BENEFICIATION Up-to-date theory &apos;and practice in the mineral ,Processing field in 1963 involved subjects such as autogenous grinding, high-intensity magnetic separation, and mill control by computers. These subjects were fully discussed at the Seventh International Minerals Processing Congress held in New York City during September.

Jan 1, 1965

By Kenneth B. Higbie

Expenditures to advance scientific technology in general reached an all time high in 1965 with some $22.2 billion estimated to have been allocated by government and industry. Federal Government expenditures were estimated at $15.4 billion, with almost 90 percent of the funds devoted to programs involving defense, atomic energy, and outer space efforts. With this massive effort in the United States and a very impressive effort elsewhere in the world, there is little wonder that many new metallurgical developments were announced in the technical press during the year. No effort has been made to cover all aspects of the industry, but a few of the developments are described in this chapter.

Jan 1, 1966

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation&apos;s defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

By Rollien R. Wells

THERE are two recognized methods of recording the state of the metallurgical art. One involves delineation of individual advances reported in the literature. This approach is used effectively in the excellent annual reviews published by some of the leading technical journals and in the technology sections of the individual commodity chapters in this volume. In an effort to more clearly indicate the current trend of metallurgical research and development, the authors of this chapter chose the method of discussing generally selected items of interest brought to their attention during 1959. Since technology cannot be confined by dates on a calendar, most of the items mentioned have been in the process of development for several years. No attempt was made to identify the sources of information used here. Material was drawn from many sources : Nonconfidential correspondence and conversations with authorities of the metallurgical fraternity, papers delivered at technical meetings, and articles noted in the technical press, including particularly Engineering and Mining Journal, Metal Progress, Journal of Metals, Mining Engineering, Industrial and Engineering Chemistry, Chemical Engineering, Chemical and Engineering News, Chemical Week, Materials in Design Engineering, Review of Metal Literature, the Canadian Mining and Metallurgical Bulletin, the Mining Journal (British), and the Journal of the Institute of Metals (British).

Jan 1, 1960