Search Documents

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944

By W. W. Adams

The safety record established by the coal-mining industry of the United States during 1934, although not as favorable as that for the previous year, was better than the record for any other year during the period 1930-34 for which complete figures covering fatal and nonfatal accidents at the mines are available. The number of accidents was 89.98 per million man-hours of employment compared with 86.74 for the year 1933, the latter being the lowest rate in any of the 5 years referred to. The rate was 105.60 for 1930, the first year covered by available data. Employment increased in 1934; the number of workers represented an increase of 8 percent over the year 1933, man-shifts of labor increased 16 percent, and the number of man-hours of labor increased 7 percent. The total number of man-hours of employment also exceeded the number reported for 1932, and was almost equal to the record for 1931.

Jan 1, 1936

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By W. W. Adams

With greater production of coal per man-hour of work than ever before achieved, the coal-mining industry of the United States established a better safety record in 1941 than in any year since 1930, the earliest for which complete reports of nonfatal as well as fatal injuries were collected by the Bureau of Mines, United States Department of the Interior. In only one year (1933) of the 12-year period 1930-41 was the fatal-accident rate better than in 1941, whereas the rate for nonfatal accidents was better in 1941 than in any previous year. Accident and employment reports received from mine operators, together with fatal-accident reports received monthly from State mining departments and inspectors, showed that 546,692 men were employed in and about the coal mines of the United States during the calendar year 1941. This number does not include office employees or coke-oven workers. The increase of 1.3,426 over the number of employees in 1940 was accompanied by a gain in man-hours of work performed at the mines and an increase in average number of hours worked per man during the year.

Jan 1, 1944

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By J. D. Davis

Coke Since the beginning of manufacturing of metallurgical coke in the United States, which dates from about 1859, Pennsylvania has main tamed supremacy in coke production Available statistics for the year 1880 show an output of 3,338,300 short tons, which was neatly trebled by the end of the succeeding 10 years. From this time on the increase was steady, though not rapid, and in 1922 the total production was 13,991,892 tons, which is approximately 37 per cent of the total coke production of the United States. The main reason for the rapid development of the coke industry in Pennsylvania lies in the abundance of coals particularly adapted to beehive coking, for which purpose the Pittsburgh bed in the Connellsville district has long been looked upon as standard At first practically all metallurgical coke was made in beehive ovens, the only exception being the short lived and wasteful method of coking in piles, byproduct owns did not make then appearance until after 1893 The suitability of a beehive coking coal cannot be accurately predicted from its chemical analysis, but it can be said, perhaps, that the volatile matter should be about 32 per cent, and that the oxygen content should not be mole than 10 pet cent or less than 4 per cent The sulphur and phosphorus content should be small-not over 1 25 per cent sulphur and under 0 02 pen cent phosphorus-and the ash content should not be over 7 per cent The Pittsburgh bed at Connellsvnlle fills these requirements well, as may be seen from the following representative analysis. Analysts of coal from Pittsburgh bed Moisture 1 70 Volatile matter 31 10 Fixed carbon 59 80 Ash 7 40 Sulphur 0 85 B t u 13,990

Jan 1, 1928

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical studies have been prepared for the US Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which we may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to- noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna con- figurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National Bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by NBS. The recent NBS data is that used by Collins in the final predictions. The following outline indicates the order and subject matter treated in the subsequent sections: Section 2 - Signal-to-Noise Analysis for Loop-to-Loop Mine Communications Section 3 - The Horizontal Electric Dipole Section 4 - Signal-to-Noise Analysis for Down-Link Line Source Mine Communications Section 5 - LF Communication Section 6 - The Application of Recent NBS Noise Data to Mine Communications Section 7 - Analysis of Mine Communication Propagation Programs

Nov 15, 1974

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract SO122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine. Field testing was conducted during the last week of November 1972, at a coal mine operated by Inland Steel Company, near Sesser, Ill, and in the Robena No. 1 Mine, Waynesburg, Pa, on 12 March 1974. The tests included uhf propagation losses and noise (200 MHz to 1 GHz) in the Sesser, I11 mine location and vlf propagation loss and noise (1 to 200 kHz) in both of the above locations. The basic experimental parameters were frequency, polarization, antenna type/orientation, and distance. The following reports treat the various aspects of the test programs in detail. Since different antenna configurations were used in the two mines, each report contains its own experimental predictions drawn from its corresponding test activities. A test equipment list and block diagrams of typical experimental setups for the tests of section 2 are contained in appendix A.

Jan 1, 1974

This report is a compilation of all information obtained in accordance with the requirements of contracts SO122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies : Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gau-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated Mine visits and in-depth interviews were made alt the following sites: Robena No. 4, Pennsylvania Greenwich Colliery Mines, Pennsylvania Somerset Coal Mine, Colorado Keystone No. 1, West Virginia Harris Mine No. 1, West Virginia Baldwin Underground No. 1 Mine, Illinois Lovilia No. 4 Coal Mine, Iowa Orient No. 3 Coal Mine, Illinois

Nov 15, 1974

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as de- rived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems. Plans in the second area of interest--that of relating communications to mining operations-- were to observe mining operations and usage of communications; to gain insight through interviews with mine management, from mine superintendents to section foreman; and to look for correlation between communications, production, and safety. Lastly the communication systems needs and requirements were determined from first hand interviews of mine personnel, from the analysis that lead to the individual reports on the eight mines, and from an overview of all of the mines studied. The latter was done to find commonality between the needs of the individual mines such that system requirements having the greatest universal value could be derived, thus lowering per-mine cost of equipment through economics of scale. Armed with tape recorders, backgrounds in communications technology, and with an interview questionnaire that was improved as experience was gained, engineers visited the eight mines to obtain the raw data from which the needs and requirements could be developed through analysis. During the first part of the program two days were spent at each mine so that interviews and tours could be completed, and so that full eight hour shift phone usage recordings could be obtained for statistical analysis. One day visits were sufficient for those trips where tape recordings were not made. During the later trips less attention was given to the statistical nature of communications, and more to how communications relates to the total mining operation.

Nov 15, 1974

By Halagowder Devaraj, Mostafa Sheykhnazari, Veer P. Bhavanandan

"A sensitive colorimetric assay for detecting mucins and glycoproteins rich in 0-glycosidically linked saccharides is reported. The method combines the susceptibility of N-acetylgalactosamine terminating 0-glyco idically linked saccharides to P-elimination with the Morgan-Elson reaction for N-acetylhexosamines with free reducing ends. All mucin and mucin-type glycoproteins but none of the serum-type glycoproteins tested resulted in characteristic color production. All mucins tested gave linear responses in the range 5 to 200 ""g and the assay was also adapted to the microscale involving the use of 96-well microtiter plates. The microassay in which the volumes of samples and reagents are scaled down 2.5-fold was particularly useful in monitoring of mucins, in the presence of other glycoconjugates, in large numbers of samples obtained during fractionation procedures. Cesium chloride, cesium bromide, potassium thiocyanate, and various detergents do not interfere with the colorimetric determination. Guanidine hydrochloride, cesium triftuoroacetate, and B-mercap- . toethanol decreased color by 30 to 45%; however, the interference was not serious to prevent the use of the method for detection of mucins in their presence. The use of the method for the specific detection of mucin during fractionation by gel filtration and density gradient centrifugation of cystic fibrosis sputum samples is demonstrated. Mucins are an important class of biomacromolecules whose structure-function relationship is poorly understood (1,2). The investigations of mucins are hampered by difficulties in purifying these very large size molecules which appear to avidly bind other components of the mucus (3,4). One of the problems during purification is the specific detection of mucins. For example, during the various purification steps, the fractions containing mucins are typically detected by assaying for neutral sugars (hexoses) (5,6), for sialic acids (7), or for periodate oxidizable saccharide units (8). However, these methods are not entirely satisfactory because neutral sugars, sialic acids, and periodate-oxidizable saccharides are also components of other glycoconjugates. In addition, the neutral sugar and sialic acid measurements are also subject to interference from high levels of proteins and nucleic acids."

Jan 1, 1990

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

Provide respiratory protection for escape in a toxic or oxygen-deficient atmosphere with a device small and light enough to be belt-worn. Approach Combine a 10-minute, belt-worn respirator with a stored, larger, long-duration (60-minute) attachment that can be plugged into the 10-minute unit without removing the mouthpiece. How It Works The 10-minute device will be carried by the miner at all times, and the 60-minute canister or attachment will be stored near the miner. In the event of a disaster, the 10-minute device would be donned immediately. The miner would then proceed to the stored 60-minute unit and plug it into the 10-minute unit. For the 10-minute unit, a breathing circuit was developed in which air is passed through the KO2 bed twice per respiration. The 60-minute canister differs from the 10-minute unit in that air is drawn only once through the chemical bed per respira-

Jan 1, 1981

By Alan Mayton, N. Kumar Kittusamy, Christopher Jobes, Farid Amirouche

Industrial equipment exposes individuals to whole-body vibration (WBV) and mechanical shock. This exposure can negatively impact their health, safety, comfort, and working efficiency and performance. Accordingly, proper seat design is an important consideration in reducing the adverse effects of WBV exposure to vehicle operators. Since the human body is sensitive to low frequency WBV, ride quality is a basic and important element of good seat design. When designing a suitable seat, it is essential to understand vibration exposure environment of workers and how well they can tolerate this environment [1]. This is particularly true in the mining industry. Mayton et al. [2] reported on a low-coal shuttle car seat design that underwent limited, yet successful underground mine trials. Building on this work, a follow-up study compared NIOSH and existing seat designs on low- and mid-coal seam shuttle cars. The NIOSH seat designs included viscoelastic foam, which has properties similar to those found in a mechanical spring/damper suspension system. The seats also included an adjustable lumbar support and a fore-aft seat adjustment. The NIOSH seat designs contrast with the existing seat design, which have little or no lumbar support and include inexpensive foam padding of the type commonly used in furniture. This paper will focus on the seat designs for the mid-coal seam shuttle car and compare subjective comfort data collected from five vehicle operators with ISO 2631 – based reduced comfort boundary (RCB) analysis of recorded vibration levels. Methods Experimental data were collected using three different tools: triaxial accelerometers, pre-amplifiers, and filters connected to a data recorder; a visual analog scale (VAS); and a short questionnaire. Researchers recorded quantitative or objective vehicle vibration data to determine the input and output acceleration at the operator cab floor and operator seat interface. Qualitative or subjective data, collected with the VAS, allowed researchers to obtain the operators’ immediate impressions of shock, vibration, and discomfort levels for the vehicle ride on each of the seat designs. Each shuttle car operator made six round trips with the vehicle each seat. The shuttle car operator marked the VAS on the first, third, and sixth round trip of the trials for each seat. A round trip consisted of traveling to the coal face with no load and returning to the load discharge location with a full load of coal. Results Total overall average ratings for the five vehicle operators of the mid-coal seam shuttle car, showed that operators sensed from 45 to 87% less discomfort with NIOSH seat designs compared to the existing seat design. Using a 95% CI, researchers computed a strong positive correlation for discomfort. Figure 1 illustrates the RCB analysis method for one of two NIOSH seat designs.

Jan 6, 2006