Search Documents

By G. S. Scott

It is sometimes desirable to know what changes in sizing characteristics would appear in screened coals if screens of different - size openings than those employed had been used . This report is concerned entirely with the application of the Rosin- Rammler law to a solution of this problem .

Dec 1, 1943

By E. W. GOODWIN, V. F. Parry, J. B. Goodman, L. D. Schmidt, J. D. Davis, A. C. Fieldner, W. S. Landers, J. L. ELDER

The Heliopore process is essentially an arrangement that uses the waste heat in the exhaust gas of an internal - combustion engine to carbonize coal (noncaking ) or lignite . The gases distilled from the coal furnish fuel for the internal - combustion engine , which drives an electric generator . Thus the main products of the plant are electricity and char . A flow diagram illustrating the principles of operation of the Heliopore process is given in figure 1. The primary equipment consists of a carbonizing retort , gas cooling and scrubbing equipment, a gas storage holder, and an engine to burn the gaseous carbonization products . Coal is charged into the top of the retort while the hot gases from the engine travel upward through special ducts in the retort countercurrent to the coal flow . The hot gases never come into direct contact with the coal . Char is discharged at the bottom of the retort and hot gases at the top . The gaseous products resulting from carbonization of the coal are drawn off by an exhauster through the condensing and scrubbing equipment to take out tar and liquor , then to a gas holder , and finally are burned in a gas engine . The gas engine drives an electric generator and the engine exhaust gases are returned to the retort to carbonize coal . The entire process was intended to be continuous and self - sustaining, and to use coal as the only fuel . The plant may be said to be a large - scale pilot plant in that , although it is of full commercial size , its main purpose is to provide data for the design of others of its type . The installation tested had a daily throughput of about 4 tons of coal . Figures 2 , 3 , and 4 picture some details of the plant and equipment used in the experimental testing . Further details of the equipment and engineering drawings of the castings are shown in figures 8 to 22 in the Appendix .

Dec 1, 1943

By Griffith. F. E., Glei

"INTRODUCTION For many years protective grounding of electrical equipment has been advocated as a means of safeguarding equipment against damage and of minimizing shock hazards to persons. Several codes are in effect covering in considerable detail the items to be observed in obtaining effective grounding in and about industrial plants. Although the coal-mining industry does not have a comprehensive code of its own covering the grounding of electrical installations, a number of States and individual coal-mining companies have issued codes, standards, or rules that include certain requirements with reference to grounding. As early as 1916, 4/ and again more recently, 5/ the Bureau of Mines recommended grounding, particularly as a means of preventing shock to men working on or around electrical equipment.It is common knowledge among electrical engineers of public utility and mining companies that connecting a wire from the frame of a machine to a rod or pipe driven into the earth does not necessarily assure desired protection of surface equipment. In fact, it has often been found necessary to use several interconnected rods and to treat the surrounding earth with salt or other chemicals before the connection to earth would have sufficiently low resistance to give satisfactory results. Even these expedients have not produced the desired results in some localities. It has also been found that ground connections initially having a low resistance may attain high resistance during some seasons of the year. In spite of such difficulties with surface equipment, it has sometimes been assumed that a mining machine resting on the floor in a coal mine is grounded by virtue of its contact with that floor. It has also been assumed by persons endeavoring to comply with grounding requirements that a peg or rod driven into the mine floor would provide a sufficiently low-resistance contact with the earth to be satisfactory as an electrode for connecting the grounding wire from frames of equipment. That both assumptions may be wholly untrustworthy has been proved by the authors in actual tests with underground machinery."

Dec 1, 1943

By A. J. Kraemer, O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (C. F. R. ) Committee of the Coordinating Research Council (C. R. C.) and the Bureau of Mines of the United States Department of the Interior . The first of these reports contained data on motor gasolines sold during the winter of 1935-36 and further reports on motor gasolines sold during the succeeding summers and winters to the summer of 1941

Dec 1, 1943

By J. E. Tiffany, Z. C. Gaugler

In presenting this list of permissible explosives and blasting devices , the Bureau of Mines desires to call attention to pages 16 and 23 , outlining the conditions in use under which , and only under which , the explosive or blasting device is permissible . In view of publications recounting trade practice favoring the use of a blasting device without stemming , particular emphasis is placed upon condition 4 on page lt and condition 2 on page 23 .. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming .

Dec 1, 1943

By G. S. Scott, L. D. Schmidt, J. A. KELLEY, E. L. FISH

One of the war problems with which the Bureau of Mines is concerned is to increase production of iron and steel , in which coke is one of the major factors . The output of byproduct coke for use in iron blast furnaces is insufficient and is being supplemented by coke from beehive ovens (figs . 1 , 2 , and 3) . Some difficulties that cause a reduction in iron output have been reported in the use of some of the beehive coke.6/ About 20 years have elapsed since beehive coke was made on a large scale , and many of the skilled operators of those days are no longer available . Furthermore , in many instances the quality of the coal supplied to the ovens has not been as good as formerly. The ash and sulfur contents are often abnormally high; and in other instances they vary greatly in amount, so that a nonuniform coke is produced . To assist operators to improve quality and yield of beehive coke , the Bureau of Mines equipped a truck as a field laboratory ( fig . 4 ) and sent the authors with it into the Pennsylvania beehive district . The truck contains necessary equipment for sampling and analyzing coke oven gases , measuring temperatures , screen - sizing coal, and float -and - sink testing coal . Coal specimens may be sent to the Pittsburgh laboratory for analysis . Beehive plants producing good coke were visited first to observe details of operation and to collect data on the operating process . These covered temperatures , analyses of the exit ( or trunnel) gases , and coal quality, and were to be utilized in searching for faults in plants not producing good - quality coke and to assist in improving such plants or their operation .

Dec 1, 1943

By W. A. Selvig

"INTRODUCTION In 1942, Lowry and Junge 3/ reported the results of a statistical study of errors for the proximate and ultimate analysis of coal and coke when made according to the standard Methods of Laboratory Sampling and Analysis of Coal and Coke (D271-42) 4/ of the American Society for Testing Materials. Some of the laboratories that cooperated in the investigation reported difficulty with determination of the volatile matter of anthracite and low-temperature coke. The small number of analyses reported for these particular fuels was considered inadequate to justify definite conclusions regarding the precision of this determination.The investigation described in this report was made at the request of Committee D-5 on Coal and Coke, A.S.T.M. (A. C. Fieldner, chairman), to secure additional information regarding the errors of the volatile matter determination for anthracite, low-temperature coke, and subbituminous coal; the last fuel also gives trouble in this determination, The committee has recognized that the allowable differences between duplicate determinations of volatile matter for these fuels as given in the standard methods are perhaps too stringent and may require revision."

Dec 1, 1943

By ROBERT R. ROUGH, FRANK L. BACON, John Dasher

(being shipped as bailast in ocean freighters). Within the last 10 years it has become more economical to use local sands, and there has been a general shift from the Belgian sand. Deposits of purer sand were treated and used for 'some time: but the suprly became limited, and means were sought to beneficiate the more bountiful subpay-f impure beach sands. These sands are composed of, 50 percent feldspar and 50 percent quartz, with small amounts of iron- bearing minerals, The most objectionable impurities in these West coast sands are the oxides of iron and aluminum. The Del Monte (Calif.) beach sand contains about 0.13 percent FeqQg and about 11.0 percent Aig03 (the latter being furnished by the large amount of feldspar present.) For the manufacture of feldspar present.) For the manufacture of flint-glass containers the maximuni quantities of these two impurities permitted in the sand are 0.05 percent F20 and 6 to 8 percent A1203.. The Fe0g occurs in the sand as follows: Traces of iron-bearing minerais resistant to weathering, ferruginous clay stains on the sand grains, and iron minerais not visible and possibly in solid solution or as colloidal incisions in the grains of feidspar or quartz. A good part of the iron in the sand is present in the traces of iron-bearing minerals, biotite, ilmenite, garnet, monazite; and hornblende. Biotite is present in larger quantities than the others. Samples of quartz, were freed of iron-bearing minerais by the use of heavy liquid (sp.gr. 2.70), leached with boiling HCI and SnCl2. Under a microscope a few apparently clean quartz grains were selected, and Fe203 was determined spectrographically to be 0.03 percent. The technique is similar to that described by Gabriel and Slavin. 4/

Dec 1, 1943

By G. S. Scott, G. W. Jones, F. E. Scott

An important activity of the Bureau of Mines is the promotion of safety in mining and industry . In connection with these activities , the Bureau determines the explosion hazards of combustible gases , liquids , and solids , and investigates means by which explosions may be eliminated or reduced in violence . The limits of inflammability and ignition temperatures of combustible gases , vapors , and solids are of practical importance because such materials can be manufactured , transported , and used with greater safety , provided the range of concentrations and temperatures that cause explosions are known. Acetic anhydride , ( CH3CO) 20 , with which this report is concerned , is a liquid at ordinary temperatures . It is used in the preparation of a number of organic chemicals and in the manufacture of photographic film and of artificial silk . It is perhaps the most important acetylating agent for industrial uses - a property that is especially important at this time because of its direct application in the manufacture of munitions . The sample tested was supplied by the Carbide & Carbon Chemicals Corporation . Its specific gravity was given as 1.083 at 20/20 . The vapor pressures , supplied by the manufacturer , are plotted in figure 1 .

Dec 1, 1943

By Albert L. Toenges, Louis A. Turnbull, Henry E. Dekay, James N. Scudder

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of Solid Fuels Coordinator and under the auspices of the Coke Production Committee indicated that a very appreciable increase in pig-iron production would be obtained if pres- ent blast furnaces were supplied with a more uniform coke. Control of the sulfur and ash content of coal used for making coke is an important factor in producing uniform coke and thus increasing blast- furnace efficiency. In some mines producing metallurgical coal, the analysis of the coal bed shows a wide range of sulfur and ash content. To obtain production of coal with minimum deviation in sulfur content sampling, grading, selective mining, blending, and surface preparation are practiced at some mines with satisfactory results. The mines selected for this study have developed these methods and are successfully producing coal of uniform sulfur and ash content. The systems employed at different mines vary according to the physical character- istics of the coal bed, the manner of occurrence of impuritites in the coal, the development plan and mining system, surface preparation and the acceptable impurity content of the prepared coal. The ash content of the coal can be controlled by face preparation and in the cleaning plant. The introduction of some method or practice at other mines might make possible the use of coal for inetallurgical purposes that otherwise could not be used for making coke because of the wide variation of sulfur and ash content.

Dec 1, 1943

By William Seymour, L. D. Schmidt

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of the Solid Fuels Administrator for War and with the advice of the Coke Production Committee indicated that production of pig iron could be increased. appreciably if present blast furnaces were supplied with a more uniform coke.4/ Nonvarying percentages of ash , sulfur , and fixed carbon in the coke , together with uniform physical characteristics , such as size , strength , and porosity , would aid the blast -furnace operator greatly in his trial - and - error methods of obtaining maximum production . With nonuniform raw materials he must employ certain factors of safety in operation , such as an excess of coke , an excess of limestone , and operation of the furnace below the maximum rate . Even so , he often has trouble from iron not being up to specifications , hot tops , high blowing pressures , furnace hanging up , etc. The more uniform his raw materials (of which coke is probably the most important) , the nearer to ideally can he run his furnace and thereby save raw material and increase production . One cause of nonuniformity of the coke produced by ordinary American plant practice is the prevailing lack of precise control of the bulk density ' of the coal charge in the byproduct oven . This report summarizes the available information on the subject of bulk density of crushed coal and its control . It includes brief reviews of some of the literature , some results obtained at plants visited by the authors , and results of a few preliminary tests made at the Pittsburgh Station of the Bureau of Mines .

Dec 1, 1943

By Boyd Guthrie

The current use of Mid - Continent crude oil for the manufacture of war products , such as aviation gasoline and lubricating cil , has caused an acute shortage of available supply from established sources . Therefore , refiners who heretofore have had no reason to use West Texas crude oils now are considering them as charging stock and need more information concerning their characteristics . The Bureau of Mines has published several reports3/ giving analyses of the most important of these crude oils . However, to make the applicable data in these publications readily available to refiners , the present compilation of analyses of West Texas crude oils has been prepared . Data showing the effect of catalytic desulfurization of naphthas from West Texas crude oils have been presented in a restricted Bureau of Mines Report of Investigations . These analyses were made under the general supervision of R. A. Cattell , chief, Petroleum and Natural Gas Division, Bureau of Mines , Washington, D. C. , and N. A. C. Smith, supervising engineer , Fetroleum Experiment Station, Bureau of Mines , Bartlesville, Okla . , and under the direct supervision of Harold M. Smith, senior petroleum chemist, Bartlesville , Okla .

Jan 1, 1944

By Wilbert J. Huff

For the past 8 years the technical studies conducted by. the Explo- sives Division of this Bureau have been summarized in a series of annual reports.3 This report deals with activities from July 1, 1942, to June 30; 1943. Specific problems have been in immediate charge of section or unit leaders, to whom credit is given.

Feb 1, 1944

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By W. H. Ode, W. A. Selvig

Investigations have shown interesting relationships between primary-tar and light-oil yields and chemical analyses of coals. These studies have been based largely upon results published by the Bureau of Mines in connection with its survey of the gas-, coke-, and byproduct-making properties of American coals. This paper gives the results of a similar correlation in which the range in rank and type has been extended to include nearly all classes of coal, the object being to determine relationships that are significant in predicting tar and light-oil yields from chemical analyses of coals. The yields of primary tar and light oil are important in two fields of coal utilization, namely, combustion and carbonization. It is generally recognized that the principal cause of smoke produced upon burning coal is incomplete combustion of tar and light-oil vapor released during burning. The greater the tar and light-oil yields of a coal, the greater is its potential smoke-producing property. During the present war, development of new sources of fuel oil has been emphasized, especially where the supply of petroleum products is limited. One possible source of a substitute fuel is the tar and light oil that can be obtained by low-temperature carbonization of coal. In both England and Germany large quantities of low-temperature tar and oil are being processed as a source of liquid fuels. It is obvious that primary-tar and light-oil yields are of paramount importance in the selection of coals for such use.

Mar 1, 1944

By D. A. Reynolds, J. D. Davis

"INTRODUDTION Investigations by the Bureau of Mines have shown that the carbonizing properties of splint and bright coals may differ greatly. In a study of 55 coal columns selected from representative coals of the Appalachian region, Sprunk and coworkers 10/ compared various chemical and physical properties of splint and associated bright coals. Carbonization tests in the Fischer retort at 932°F. (500°C.) showed that, except for bright coals of high oxygen content, the coke residue from bright coal was much more swollen and cellular than that from splint. ·with one exception, agglutinating values determined by the Bureau of Mines test, were lower for splint than for associated bright coal.Because sorting of coal in quantity is tedious and time-consuming, separate types have not been carbonized by the Bureau of Mines-American Gas Association (BM-AGA) test, which requires 85- to 200 pound charges. However, this method has been used to determine the carbonizing properties of samples 0f bed layers that are composed largely of either splint or bright coal.4/ In these earlier tests, which were made at high temperatures on layer samples from the Elkhorn bed, Letcher County, Ky., the splint coal yielded more coke than the bright coal, and this coke was slightly stronger than that from the bright coal. The cokes from samples with large proportions of bright coal were more cellular or porous, as were the low-temperature cokes obtained from carbonization of separated samples of bright coal in the Fischer retort."

Apr 1, 1944

By G. Dale Coe, Will H. Coghill

The " periodic pincer " herein described fills a need for a device to control the rate of flow of a wet ore pulp through an orifice . Two uses of the periodic pincer to be discussed are on classifiers and on a wet ore feeder . Although the immediate necessity that brought about this device was for better operation of a miniature hydraulic classifier , in connection with an investigation of iron- ore concentration being conducted by the Federal · Bureau of Mines , with the cooperation of the University of Alabama , the device has promise of a wider field of application . In the iron - ore work , the need became so acute for a nonchoking , uniform - delivery classifier spigot that development of a suitable device was imperative .

Apr 1, 1944

By Irving Hartmann, John Nagy

As part of a program designed to promote safety in industrial operations , the Bureau of Mines has been investigating the explosibility of numerous powdered products and dusts and studying means for the prevention of dust explosions . In a previous paper the results of a study of the inflammability and explosibility of metal powders were published . This report summarizes a similar study which has been made on various powders used in the plastics industry. The work was undertaken to provide information for a subcommittee of the Dust Explosion Hazards Committee of the National Fire Protection Association, which was charged with preparation of a code for the prevention of fires and dust explosions in plants producing or processing synthetic resins and molding compositions . The production of powders and generation of inflammable dusts are inherent in one or more steps of the manufacturing process of many resins and molding compositions, and control of the dust hazard is a major problem in the plastics industry . In the preparation of phenolic resin molding powders, for example , the solid synthetic resin is crushed and pulverized , and then blended with ground wood flour , cotton flock, or other fillers , as well as with coloring pigments . This raw mix is then passed through compounding mills , from which it emerges in the form of homogeneous sheeted stock, which is crushed , ground , and graded to form the molding powder . The number of major dust explosions in the plastics industry has been limited, but numerous small explosions have occurred, and in view of the ever -increasing volume of production the potential explosion hazard must be considered a very real one . Fortunately, this fact is realized by several manufacturers of plastic compounds , as well as by insurance companies , who are taking precautionary measures against possible accidents and during the past year or two have submitted numerous powder samples to the Bureau of Mines for explosibility tests .

May 1, 1944

By Allen D. Look, Norman King

For many years, much thought and effort have been devoted to the achievement of safety in the use of explosives by those interested in the preservation of human life and the protection of property. As a result, we now have adequate rules pertaining to the safe use of explosives , which, if observed, would prevent many, perhaps ail , of the explosives accidents that yet occur . Although the rules respecting the use of explosives are believed to be well - known, many accidents occur because they are disregarded . The mental awareness aroused by a tragic accident usually will cause safety precautions to be taken for a while ; however , this awareness gradually disappears unless a sincere effort is made permanently to prevent similar accidents . Frequently, because safe methods are more irksome than unsafe methods , the lessons taught by accident experience are forgotten in a short time , vigilance is relaxed , and there is a gradual return to unsafe , easy methods of performing work. If the preservation of human life is important , the unfortunate experiences of others and the lessons taught by them should be applied to reduce unnecessary loss of life . The value of a life lost as the resuit of accident should be calculated not only from the monetary and humanitarian standpoint but also according to what the accident could contribute in the way of saving other lives and suffering . This saving of other lives can and will , if the lessons from unfortunate accidents are applied , convert a loss to a gain a gain of such magnitude that the accident victim could be considered

May 1, 1944

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944