Search Documents

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By A. N. Fried

One of the important problems confronting oil producers in appraising the possibilities of secondary recovery in many California fields is the effect of viscosity on oil recovery by water flooding. In January 1954 there were 554 fields and/or pools, in the State, that produced 1 million barrels daily, and 138 of these pools produced approximately 267 thousand barrels daily of heavy crude oil having gravities below 200 API. Many of these fields are nearing the end of their primary economic life and still have high residual-oil saturations, a favorable factor in water flooding. The crux of the problem is whether or not enough oil can be recovered from these fields by water flooding to make the operation economically successful. Some experiments on the relationship between viscosity and oil recovery have been made by other investigators, but in most instances the viscosity of the oils used in the experiments was lower than the viscosity of the oils found in many of the heavy-oil fields in California. A study was undertaken, therefore, to determine the relationship between oil viscosity and recovery over a wider range of viscosities and to compare the experimental results with those predicted by theoretical calculations.

Jan 1, 1955

By W. L. Crentz

The Black Mesa coal field is part of the Hopi and Navajo Indian Reservation in Apache, Navajo, and Coconino Counties, Ariz. The field is in an isolated area with the nearest railroad 70 to 90 miles to the south. Travel is restricted by roads that become impassable during inclement weather. The area is a mesa and rises from 500 to 2,000 feet above the surrounding territory. Water is very scarce, and the nearest stream of any consequence is the Colorado River about 90 miles northwest from the center of the field. Coal beds are found in the Mesaverde formation of the Cretaceous age, but they are uncorrelated and range from subbituminous to bituminous in rank. Huddle2/ estimates the reserves of subbituminous coal in Arizona at about 15 billion tons, most of which is in the Black Mesa field. The geology of the field has been reported by Campbell and Gregory.3/ Coal production is small, and the output is used almost exclusively for domestic fuel in the Indian schools, missions, and trading posts.

Jan 1, 1955

By R. W. Huber, R. C. Wiley, V. C. Petersen

"Three arc- melted ingots, two of a t itanium-7 percent manganese all oy and the third of unalloyed titanium, were forged and rolled into 3/ 4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties.These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots.INTRODUCTIONArc -melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Perk, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.Considerable data have been published recently on constitution diagrams and properties of titanium-manganese alloys in genera1. 3/ 4/5/6/ However, little if any correlation between processing schedules and end results has been published, particularly with respect to the present commercial production of the proprietary titanium manganese alloys . Several factors in the production of titanium and titanium alloys have a pronounced influence on the physical and mechanical properties of the finished product: (1) The degree and nature of impurities in the base materials, ( 2) the amount of impurities introduced during the melting cycle and their distribution, (3) the homogeneity of the alloy, (4) forging, (5) rolling, and ( 6) final heat-treating cycles. All of these item£ are important from a metallurgical standpoint in producing the desired end properties in the metal."

Mar 1, 1955

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955

By L. W. Brandt

Studies of liquid-vapor equilibria of gas mixtures at the Bureau of Mines Amarillo Helium Plant Laboratory require that the equilibrium cell be maintained uniformly at any desired temperature from approximately room temperature to -320° F. The temperature-control system must also tolerate a substantial heat input, in the form of warm gas flowing into the cell, without loss of control. Temperatures between the sublimation temperature of carbon dioxide (-109° F.) and the boiling point of liquid nitrogen (320° F.) are usually obtained by methods utilizing a hydrocarbon liquid bath cooled by liquid nitrogen.4/5/6/7/ Owing to the fire hazard attending such baths, a safer method of temperature control was desirable.

Jan 1, 1955

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

By J. B. Gayle

A half-ton experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial, slot-type ovens. The reasons for constructing an oven of this Size, the details of the design, and the operating characteristics of the oven have been given in previous publications.3/4 The present report deals with the reproducibility of test-oven data and the effects of variations in flue temperature on the physical properties of the cokes produced. Also included are the results of 2,400° carbonizing tests for several coals and coal blends not included in the earlier reports.

Jan 1, 1955

By F. W. Wood

The method described may be used to delineate irregularities, inclusions, porosity, or shrink holes in ingots up to 43 inches in length. Rou¬tine testing does not require technical personnel, and the equipment is easily maintained. INTRODUCTION For a number of years, the Northwest Electrodevelopment Laboratory of the Bureau of Mines, Albany, Oreg., under contract with the Atomic Energy Commission and the Naval Reactors Division of the Bureau of Ships, has studied the production of zirconium and has adopted the Kroll magnesium-reduction process3/ as the, most economical means of producing high-purity zirconium sponge in quantities commensurate with demand. Consumable-electrode arc melting4/ provides a practical means of melting the sponge without increasing the impurity content. The ultimate application for which the metal is intended requires that strict specifications be met to insure workability and maintain the nuclear properties and corrosion resistance. The control measures employed to satisfy these specifications include chemical, spectrographic, and metallographic analyses, mechanical and corrosion tests, and ultrasonic inspection of the finished ingot. The primary purpose of ultrasonic inspection is to augment the other control measures by checking the soundness of each ingot leaving the laboratory. An incidental but important function has been the revelation of information leading to better understanding of the arc-melting process. For example, information obtained through ultrasonic inspection relative to the occurrence and distribution of porosity in ingots has resulted in a. modification of melting practices that minimizes the occurrence.

Jan 1, 1955

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By L. H. Banning

In the fall of 1953 the Philippine Bureau of Mines, under a Foreign Operations Administration Technical Assistance (FOA-TA) program, began a systematic investigation of the nickel content of the well-known Surigao laterite areas, on the island of Nonoc northeast of Mindanao, to determine the occurrence, distribution, and grade of nickel contained in the laterite and in the subjacent serpentine. At the same time, a technical review of the possibility of producing commercial ferronickel from the nickeliferous materials in the Philippine Islands was made, and a smelting process was suggested. The proposed process would be similar to that developed by the Federal Bureau of Mines for the reduction of the nickeliferous serpentine occurring in the Nickel Mountain ?deposit at Riddle, Oreg. The potential avail-ability of electric power from the Maria Cristina facilities at 3 mils per kw.-hr. would enhance the economic possibility of this program. Development of an economically feasible process for recovering nickel from the nickeliferous serpentines and laterites should lead to the establishment of a new industry in the Philippines, to the development of a source of nickel in the Far East, of which at present there is none, and to partial solution of the problem of supplying the free world with nickel. Enough preliminary reconnaissance had been completed by early 1954 to permit sampling of the deposit for metallurgical investigations. The FOA then requested the Federal Bureau of Mines Northwest Electrodevelopment Laboratory, Albany, Oreg., to conduct preliminary electric smelting studies on nickeliferous serpentine and laterite samples.

Jan 1, 1955

By B. E. Blair

"This report presents the physical properties and related geological and petrographic data of some 84 rock types from operating mines, quarries, or blasting research test sites. These fundamental rock data were collected as a quantitative approach to underground mining problems, blasting research, or other related studies; however, the data are equally applicable to any problem wherein rock characteristics are important factors. Stress-strain curves are given where available, and the standardized procedure for determining elastic constants from static tension tests is described. Computed (laboratory) and measured (field) free-medium velocities are compared in those instances where such data are available. A chart is given showing both the optimum and minimum number of test specimens for the various core sizes employed in the Bureau of Mines standardized physical-property tests. Rock-type, geographical, and geological indexes are included to aid the reader in locating physical-property data in this and previously published Bureau of Mines physical-property reports.INTROD'OCTI ONThis report presents the physical properties of 84 rock types tested from 16 different projects (sections 37-52). Two previous physical-property reports 2-3 / (hereinafter referred to as parts I and II) presented data on 160 rock types from 36 different projects (part I, sections 1-25 and part II, sections 26-36).The physical-property data were originally obtained to supplement structural mining problems, seismic studies, or related investigations; however, they should be equally applicable in all fields of studies where the strength, hardness, or other properties of rock are important factors. The properties, determined from laboratory tests performed on diamond-drill core, include the following:"

Jun 1, 1955

By Lloyd Williams

1. The investigation shows that the bed identified as Wilder in this report is the only bed in Overton County that has produced commercial coal and is the only bed in which coal reserves were estimated for this report. Three other coal horizons were recognized but lacked enough data for reserve estimates. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 19 million short tons, as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas of the Wilder bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955