Search Documents

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

By R. B. Stroud

Bureau of Mines studies of copper-bearing Permian red beds, which extend from north-central Texas through western Oklahoma to southwestern Kansas, indicate heretofore undefined commercial possibilities for low-grade, medium-volume, strip-mining operations. Potential ore bodies are indicated containing 0.5 to 1.5 percent copper in zones 6 to 12 inches thick. Cost analysis studies indicate a commercial operation is feasible for a hypothecated 1,000-ton-per-day ore mining and milling complex where a maximum of 60 feet of overburden can be stripped in mining a seam of shale 12 inches thick containing 1.2 percent copper

Jan 1, 1970

By R D. Fleming

A single-cylinder research engine was operated on pure hydrocarbons and simple (two-component) mixtures of pure hydrocarbons to study the effect of fuel composition on exhaust emissions from a spark-ignition engine. Used as fuels were three pure hydrocarbons that represented the primary hydrocarbon types present in commercial motor fuels: A paraffin (2,2,4-trimethylpentane), an olefin (2,4,4-trimethylpentene-2), and an aromatic (meta-xylene). The engine was operated at the same equivalence ratio for all of the fuels used in the experiment. Exhaust gas samples were collected and quantitatively analyzed for carbon monoxide, carbon dioxide, hydrogen, nitrogen oxides, aldehydes, and hydrocarbons. Exhaust hydrocarbons were separated and quantitatively measured with a chromatographic system employing a flame-ionization detector. Unknown hydrocarbons and oxygenated materials in the exhaust were identified with a Time-of-Flight mass spectrometer coupled to a chromatographic system. The results of the exhaust gas analyses showed that ethylbenzene, l-methyl-3-ethylbenzene, and l-methyl-3-vinylbenzene were more abundant in the exhausts from either 2,2,4-trimethylpentane--m-xylene or 2,4,4-trimethylpentene-2--m-xylene fuel mixtures than in exhaust produced from m-xylene. Also, the pure 2,4,4-trimethylpentene-2 fuel produced smaller amounts of C2 to C7 olefins in the exhaust than that produced by the pure 2,2,4-trimethylpentane fuel. The exhaust from pure m-xylene fuel contained aromatic hydrocarbons of higher molecular weight than the parent fuel. The amount of total hydrocarbon (moles of exhaust hydrocarbon per mole of fuel used) in the exhaust from the three pure fuels decreased in the following order: 2,2,4-trimethylpentane > 2,4,4-trimethylpentene-2 > m-xylene. The hydrocarbon mole-fractions of unreacted fuel in the exhausts produced from each of the pure fuels were 0.20 for 2,2,4-trimethylpentane, 0.13 for 2,4,4-trimethylpentene-2, and 0.66 for m-xylene.

Jan 1, 1970

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By William L. Rice

Geochemical humus sampling techniques were used by the Bureau of Mines in investigating a potential large, low-grade gold deposit in the Orogrande district, Idaho. Conifer needle humus samples were processed by ashing and fire assay-atomic absorption analysis. An area bearing anomalous concentra¬tions of gold and silver was outlined by the geochemical method.

Jan 1, 1970

By Ronald M. Van Noy

A reconnaissance study of kyanite-group mineral deposits in the Northwest has revealed large exploitable reserves of the mullite-forming raw materials in the Woodrat Mountain and Goat Mountain districts of north-central Idaho. Potential coproducts or byproducts are garnet and muscovite mica. The Woodrat Mountain district contains garnet-kyanite-mica schist, which has been traced for 6 miles and may extend farther. Surface samples average 29 percent kyanite and contain up to 15 percent garnet. Inferred reserves of strippable ore with a low waste-to-ore ratio, and containing more than 15 percent kyanite, are more than 3 billion short tons. The Goat Mountain district contains several kyanite-mineral zones. Samples of the richest zones average from 10 to 20 percent kyanite minerals and represent about 200 million short tons of strippable rock. Beneficiation tests indicate that the kyanite minerals and garnet can be concentrated by a combination of gravity, flotation, and electromagnetic methods. Reserves in these deposits are sufficient to satisfy any foreseeable domestic and export demand. However, the freight tariff to reach the nearest major users of kyanite (located in the Midwest) has discouraged development of western kyanite resources. Western demand of a magnitude to support a moderate to large milling operation has not yet been developed. However, there is some foreign market potential. If a garnet byproduct could be prepared and sold for coated abrasive products or as grinding grains, an offset possibly could be gained to a por¬tion of the mining and milling costs for the Pacific Northwest producer. Such byproduct values would offer a means for expanding the geographic market areas as well as the regional market potential.

Jan 1, 1970

By C. H. Schwartz

A thermal radiation probe was constructed and tested in pulverized-coal-fired furnaces. A rotatable sensing head on the side of a water-cooled probe permitted measurement of radiant flux within a 7.20 cone from any desired direction to a point within a furnace. A response curve for a corner-fired furnace showed radiant flux of 130,000 Btu per sq ft per hr, when viewing flame, and 60,000 Btu per sq ft per hr, when sensing wall reflection. Detailed drawings and fabrication procedure are given.

Jan 1, 1970

By W. S. Sanner

Pyrolysis (destructive distillation) techniques developed at the Bureau of Mines to determine the yield and quality of the products from coal were used to convert municipal (household) and industrial refuse into potentially useful solids, liquids, and gases without adding to environmental pollution. The tests demonstrated that a ton of municipal refuse can be converted into 154 to 424 pounds of solid residue, 0.5 to 6 gallons of tar, 1 to 4 gallons of light oil, 97 to 133 gallons of liquor, 16 to 32 pounds of ammonium sulfate, and 7,380 to 18,058 cubic feet of gas. A ton of industrial refuse, consisting of paper, rags, and cardboard, can be converted to 618 to 838 pounds of residue, 1.5 to 3 gallons of light oil, 68 to 75 gallons of liquor, 12 to 23 pounds of ammonium sulfate, and 9,270 to 14,065 cubic feet of gas. The energy from the gas is more than sufficient to provide the heat for the pyrolysis.

Jan 1, 1970

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

By L. B. Pankratz

Enthalpies above 298° K were determined for AgCl to 1,400° K and for AgBr to 1,200° K by copper-block calorimetry. Before melting, both compounds showed an anomalous increase in enthalpy, an effect associated with lattice defect formation. Melting points and heats of fusion were determined to be AgCl, 730° K and 2,945 cal/mole; AgBr, 700° K and 2,030 cal/mole. The heat capacity of both melted substances decreased with increasing temperature over the entire liquid ranges investigated. Enthalpies above 298° K were tabulated at even temperatures along with derived entropy increments and heat capacity values. The results were combined with the known heats of formation and entropies at 29.8.15° K to obtain values of the heats and free energies of formation over the range 298.15° to 1,400° K for AgC1 and 298.15° to 1,200° K for AgBr.

Jan 1, 1970

By Harold A. Watson

A method for measuring leakage of vapors into a chemical-cartridge half-mask facepiece during simulated use is described. The respirator, fitted with high efficiency cartridges, is worn in a dichlorodifluoromethane (CC12F2)--air test mixture while a series of timed activities (facial movements, varied breathing, exercise, etc.) is performed. Complementing other tightness tests, this method is useful particularly for studying face fit and the effect of facial movements on leakage. The concentration of CC12F2 within the facepiece is monitored continuously to observe the immediate effect of physical activity on leakage. A composite sample is collected simultaneously in a plastic bag as a measure of average leakage during the 18-minute test period. Leakage, reported as percent, is calculated from the concentrations of CC12F2 within the facepiece and in the test atmosphere.

Jan 1, 1970

By Fred Leighton

The Bureau of Mines has developed rock noise source location techniques that may be used to obtain precise and practical source locations from micro-seismic field data. These techniques enable one to monitor all or any part of a rock structure and map progressive stress buildup or rock movement. Thus, the microseismic method of determining instability in rock structures is becoming an invaluable engineering tool for the mining or civil engineer engaged in rock excavation and construction.

Jan 1, 1970

By Basil Dimitriades

The roles of hydrocarbons and nitrogen oxides in smog formation were investigated by the Bureau of Mines. Samples of automobile exhaust with varying HC and NOx levels were irradiated in a smog chamber under conditions that resulted in smog levels similar to those observed in the atmosphere. Results were used to define the patterns that describe the dependence of a number of smog manifestations on HC and on NOx. Using these dependence data and some simplifying assumptions, estimates were made of the ranges within which HC and NOx must lie in order to obtain specified levels of air quality.

Jan 1, 1970

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By L. B. Pankratz

Enthalpies were determined for synthetic chalcopyrite (CuFeS2) between 298° and 1,050° K and for synthetic bornite (Cu5FeS4) between 298° and 1,100° K by copper-block drop calorimetry. Two transitions were found for each compound. The lower transitions were both crystal transformations from tetragonal (low-temperature form) to cubic (high-temperature form). The chalcopyrite transformation occurred at 830' K with a heat of transformation of 2,405 cal/mole; the bornite transformation was at 485° K with a heat of 1,430 cal/mole. The other transitions were of the second order and were presumed to be magnetic in character. The second-order transitions for chalcopyrite occurred at 930° K, and the one for bornite at 540° K. Enthalpy increments, entropy increments, and heat capacities are tabulated at even temperatures above 298.15° K. Equations of enthalpy are also given.

Jan 1, 1970

By Clarence O. Babcock

In this report, the Bureau of Mines presents a method for reducing the complexity of designing room-and-pillar mining systems by treating them as anisotropic soft inclusions in the surrounding ore or host rock. Theoretical models were derived for the calculation of the effective Young's moduli for these systems. The predicted behavior of the plate-type elements used in these models agreed well with test results from 21 plates each with 49 holes spaced on a 7 X 7 Cartesian grid. The plates behaved as anisotropic solids, the effective Young's moduli of which could be predicted from the scaled hole size and spacing. Actual hole shape was insignificant. The effective Young's moduli for simple mining systems are calculated in sample problems. This approach should provide information about field stress in the mining region and the stress distribution in the surrounding ore or host rock when the actual mining configuration is replaced by an anisotropic inclusion in a finite element analysis. The field stress within the inclusion can then be applied to the actual opening shape to determine the stress distribution within the mining region.

Jan 1, 1970

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag composition. Liquidus and solidus temperatures and solid solubilities were determined for the BaF2-Y203 system, and the information is presented as the phase diagram. The phase diagram was constructed from data obtained by ceramography, X-ray diffraction, and thermal analysis of specimens encapsulated in small molybdenum ampoules. The data indicate a simple eutectic system with maximum terminal solid solubilities of less than 1 mole pct. The eutectic temperature is 1,343° C, and the composition of the eutectic is less than 1 mole pct Y203.

Jan 1, 1970

By J. M. Singer

Approximate equations were used to compute the radiant heating of float coal dust by approaching flames for various combinations of particle size, dust path length (flame travel distance), flame temperature, dust concentration, flame speed, and flame length. The computed values of degree of radiant heating and flame travel distance for preheating the coal dust should be useful for estimating the increased fire hazard of different coal dust-flame parameters. Some findings relating to coal mine disaster control are-- 1. Coal dust clouds cannot be preheated to ignition temperatures by flame radiation alone when deflagration speeds are greater than about 10 m/sec. Thus it appears unlikely that radiation alone will cause flames propagating in dust clouds to accelerate to detonation velocities. 2. Small particles in the radiation flame zone caused by burnout and soot formation increase the degree of preheat significantly. 3. The concentration of float coal dust (radii = 3 to 40 microns) for maximum radiant heating usually peaks in the range 50 to 200 mg/liter of air.

Jan 1, 1970

By K. J. Miller

A laboratory electrophoresis column was designed to separate pyrite from fine coal by utilizing an observed difference in the electrophoretic mobilities of the two materials in water. The apparatus worked well when tested with synthetic mixtures of coal and pyrite, but some modifications in design and procedure were necessary to provide a sharper separation. After these changes were made, the column was tested with a high-pyritic-sulfur raw coal sample. The column successfully fractionated the sample, removing not only the pyritic refuse, but a siliceous refuse as well. The invest ion demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis.

Jan 1, 1970