Search Documents

By Gary P. Sames

Shale roof deterioration in coal mines. caused by ventilation air humidity fluctuations, is a common ground control problem. Shale roof deterioration often results in increased accidents, decreased production, inadequate ventilation, and increasing operating costs in maintaining haulage roads and airways. The results of Bureau of Mines research indicate that air tempering entries are an effective method of controlling deterioration prone shales. Some of the conclusions and recommendations drawn from Bureau research include (1) moisture sensitive shales will react adversely to moisture gains and losses, (2) the majority effect of specific humidity fluctuations can be concentrated in and absorbed by tempering entries, (3) tempering entry panels should be located as near to the main intake as possible, (4) tempering panels should be designed for a conservative recovery and provide a minimum of 20-to 30-min air residence time, (5) ventilation and escapeway requirements must be considered early in panel design, and (6) an efficient support and sealant plan can increase the life expectancy of a tempering panel.

Jan 1, 1985

By B. W. Jong

The Bureau of Mines studied reinforcement of sulfur concretes using glass, polyester, and aramid fibers. The objective of this research was to determine the feasibility of fiber-reinforcing the sulfur concrete to enhance the flexural properties. Optimum fiber sulfur concrete compositions were formulated with a cement-to-fiber ratio of 9.0:1 for glass-fiber and polyester-fiber sulfur concretes and 12.1:1 for aramid-fiber sulfur concretes. Test samples were prepared using techniques developed by the Bureau of Mines. Flexural strength values of up to 50 pct of compressive strength values were achieved with fiber additions. With non-fiber-reinforced sulfur concrete, the values ranged up to 20 pct. The impact strength and fracture toughness of sulfur concretes were increased sig-nificantly by reinforcement with glass or with aramid fiber and were adversely affected by use of polyester fiber. Strain tolerance was doubled and failure mode was shifted from catastrophic to noncatastrophic type by adding glass fiber. The glass-fiber and aramid-fiber sulfur concretes are resistant to acid corrosion and have proved durable in freeze-thaw cycles. This laboratory and field evaluation has shown that fiber reinforcement of sulfur concrete is feasible and that it enhances the flexural properties.

Jan 1, 1985

By R. B. Prater

The Bureau of Mines conducted research to separate the F from byproduct Zn concentrates obtained from fluorspar (CaF2) production, as part of the Bureau's effort to devise efficient, environmentally acceptable technology for recovering Zn from resources considered undesirable by Zn producers. Sulfuric acid (H2SO4) was found to be effective in F removal, while ammonium carbonate [(NH4)2C031 was not. The most important variables for reducing the necessary residence time were found to be temperature and agitation. Optimum leaching conditions were 75° C and 500 r/min for 2 h at 40 pct solids with 0.2 g acid per gram of concentrate, which resulted in a 98.3-pct F extraction. Zinc losses during F removal were in the range of 2 to 3.3 pct. Other elements such as Fe, Cd, Ca, and Cu were also partially dissolved. About 93 pct of the F was removed from the leach solution by neutralization and precipitation with calcium hydroxide [Ca(OH)2]. Additional treatment might be necessary to limit the buildup of soluble elements in the recycled leach solution.

Jan 1, 1985

By C. W. Smith

The Bureau of Mines conducted physical and chemical beneficiation studies on three samples of waste investment casting molds to devise a method to liberate and recover zircon. Rod mill grinding, autogenous attrition grinding, and caustic leaching were liberation methods inves-tigated. Flotation, gravity separation, and caustic leaching and sizing were recovery methods investigated. Flotation techniques produced con-centrates containing up to 74.2 pct zircon with a zircon recovery of 53.4 pct. Gravity concentration produced concentrates containing up to 98.6 pct zircon; however, recovery of the zircon was only 57 pct. Caustic leaching and sizing produced concentrates containing up to 98 pct zircon with attendant recoveries of 81 pct.

Jan 1, 1985

By R. L. Soderberg

Large open stopes mined by vertical crater retreat or sublevel s are sometimes backfilled with uncemented sand to support the stope walls and alleviate rock bursts. The failure of bulkheads in two different mines prompted a research project at the Bureau of Mines to prevent a recurrence of these failures. A series of laboratory tests with drains and sand filters was conducted to measure the bulk-head pressures when adequate drainage was maintained. Results showed that bulkhead pressure was reduced to near zero while drains were in operation, as compared to full hydrostatic pressure when drains were blocked or drainage was restricted. A relatively simple, free-draining bulkhead was shown to be adequate.

Jan 1, 1985

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated an ammoniacal sulfate leach process for recovering nickel and cobalt from low-grade domestic laterites. Solvent extraction of cobalt, one of the process steps, requires the reduction of hexammine complexes of C03+ to C02+ in an ammo-niacal leach solution. Previously, reduction was accomplished using cobalt metal shot in a column. This report presents experimental results and an economic evaluation comparing two alternate techniques with the shot column: (1) an electrolytic reduction cell with an extended surface area cathode and (2) direct electrowinning from purified leach solution using a cell with a fluid bed cathode. The second alternative eliminates the conventional solvent extraction-electrowinning steps. The costs of the three methods, based on the requirements of a pro-posed commercial-sized plant, including all unit operations, were deter-mined by the Bureau's process evaluation group. The operating costs for the shot column, $1.19/kg Co, and for electrolytic reduction, $1.20/kg, are essentially the same, but the cost of direct electrowinning, $3.77/ kg Co, would eliminate this method as a practical alternative. The cap-ital cost of approximately $14.4 million for reduction in a shot column is much higher than the approximately $4.4 million for electroreduction.

Jan 1, 1985

By James P. Bennett

In this Bureau of Mines study, portions of four acidproof bricks (two red shale and two fireclay) were exposed to 20 wt pct RCI at 900 C for periods of 30 days. Three different techniques were selected to deter-mine volume expansion of these materials after exposure. Linear expansions ranging from about 0.02 to 0.12 pct were noted from Ta pin and dilatometer measurements. The use of strain gages to measure expansions was not successful. The red shale and fireclay brick with the lowest apparent porosities had the lowest expansions. Expansion data obtained by direct measurement of samples exposed for 30-day periods or by dilatometric measurement of autoclaved samples ex-posed for 2 h were comparable. This suggests the use of an accelerated autoclave exposure procedure for determining volume expansion effects of ceramic materials in acid environments.

Jan 1, 1985

By Natesa I. Jayaraman

This report describes recent improvements the Bureau of Mines made in the design of its shearer-clearer water-spray system for dust control on lonwgall shearer faces. The improvements were based on findings from a field survey of six mines and laboratory test results. The report in-cludes information on installation and use of the improved shearer-clearer system and describes a field installation and 3-week underground test of the system. The improved shearer clearer, like its predecessor, reduces dust concentrations in the shearer operator's walkway by splitting the airflow on the upwind side of the shearer and confining the dust cloud to the face side of the shearer. The improved shearer-clearer system utilizes more practical-mounting locations for the water sprays and requires less water consumption. In the underground test, the improved system maintained the clean-air split in the walkway up to 40 ft downstream from the shearer. To further improve dust suppression, cooling-water manifolds were relocated into the loading zone. The laboratory and underground tests showed that the improved shearer-clearer system and the techniques described can significantly reduce the respirable dust exposure of shearer operators from shearer-generated dust.

Jan 1, 1985

By A. R. Rule

Research was done by the Bureau of Mines to determine the effect of a low-molecular-weight polymer on wet grinding of quartz, dolomite, and a copper ore. A 5-in ball mill equipped with a torque sensor for precise measurement of input energy was used for batch grinding tests. Grinding parameters were determined from size distribution data on the feed material and ground product. Zeta potential measurements were made to determine the effect of the polymer on the surface properties of the three materials, and a viscometer was used to measure the effect of the polymer on slurry viscosity. The addition of the polymer caused a sharp increase in the negative value of the zeta potential for all three materials, indicating that pronounced adsorption was taking place. At a constant slurry percent solids, addition of the polymer caused a similar reduction in slurry viscosity for each material. For quartz, dolomite, and the copper ore, grinding efficiency, as measured by kilogram of product per kilowatt hour passing a given screen size, was not affected by the addition of the polymer. However, the lowering in slurry viscosity caused by addi-tion of the polymer permits grinding at a higher slurry percent solids.

Jan 1, 1985

By Larry A. Haas

A major problem encountered in dump leaching operations is the plugging of both the dump and the piping by precipitated iron compounds. Bureau of Mines research to obtain basic data on agitation leaching and dump leaching methods has shown that the addition of organic chelating reagents can significantly enhance the lixiviant permeability through the ore and the concentration of the metal values in the liquor. For example, the addition of 5 giL citric acid (CA) to a conventional sulfuric acid lixiviant almost doubled the fluid flow rate through 5-cm-diameter laboratory columns containing copper ore. After 185 h of per-colation leaching, the metal concentrations with (and without, in parentheses) CA were 1.7 (1.5) giL Cu, 200 (70) ppm Mn, 160 (40) ppm AI, and 6 (3) ppm Co. The enhancement of metal concentrations with chelating reagents such as CA was confirmed by determining the solubil-ity of several metal ions as functions of pH and chelating reagent con-centration. When ferric ions became insoluble at pH values above 3, the concentrations of other ions also decreased. The addition of che-lating reagents kept iron, as well as the other dissolved metals, in solution even at pH values as high as 5. Citric acid was a more effective chelating reagent than gluconic acid, oxalic acid, or sodium lignin sulfonate.

Jan 1, 1985

By T. H. Jeffers

The Bureau of Mines conducted laboratory tests to devise a procedure for extracting copper from low-grade discarded mill tailings. A solid extractant consisting of an organic solvent extraction reagent adsorbed on granular activated carbon was investigated and proved to be satisfactory for extracting copper directly from leach pulps. When this material was used in a cyclic leaching, stripping, and electrowinning pro-cess, 95 pct of the acid-soluble copper was recovered from oxidized mill tailings. The weathered tailings contained 0.24 pct Cu (total) and 0.20 pct acid-soluble Cu. The copper was recovered as cathodes containing, in parts per million, 1.6 Pb, 3.6 Fe, 0.5 Sb, 1.5 AI, 1.9 Mn, and <1 Mg.

Jan 1, 1985

By R. H. Lien

The Bureau of Mines investigated a roast-leach process for recovering a marketable lithium product from a montmorillonite-type clay deposit located on the Nevada-Oregon border. The clay sample treated in the investigation contained 0.6 wt pct Li. The lithium recovery process consisted of several unit operations. The lithium silicate compounds in the clay were converted to Li2SO4 by roasting a pelletized mixture of clay, limestone, and gypsum at 900° C in a direct-gas-fired rotary roaster. Water--leaching the calcine at 40 pct solids extracted the Li2SO4. Lithium recovery from the leach solution involved concentrating the solution by evaporation, adding Na2CO3 to the concentrated solution to precipitate Li2CO3 , and filtering the slurry to obtain the product. The product filtrate was recycled to the evaporator following a crystallization step. About 80 pct of the lithium in the clay was recovered as 99-pct-pure Li2CO3. Process operating costs were estimated at $2.12/lb Li2CO3 produced; the current Li2CO3 selling price is $1.48/lb. Raw materials. accounted for 30 pct of the total operating cost.

Jan 1, 1985

By R. Blickensderfer

Laboratory wear testing was conducted by the Bureau of Mines on a variety of typical wear-resistant alloys used in mining and mineral-processing equipment to establish their relative spalling and abrasion resistance. Test specimens in the form of 75-mm-diam balls were subjected to repeated impacts until they broke, spalled excessively, or received several hundred thousand impacts. Pin specimens removed from the balls were evaluated for high-load abrasive wear. The alloys in-cluded commercial forged steels, cast steels, manganese steels, and four types of white cast iron, with a range of heat treatments. The effects of hardness and microstructure on impact wear and abrasive wear are discussed. The data should help mine operators select the compositions and heat treatments that best suit service conditions.

Jan 1, 1985

By E. G. Baglin

The Bureau of Mines devised a procedure for selectively extracting platinum-group metals (PGM) and gold from Stillwater Complex flotation concentrate. The Stillwater Complex is the only major U.S. PGM resource. Development of a suitable extraction technique will contribute to its exploitation. The concentrate was roasted at 1,050° C to convert host base-metal sulfides to oxides and the PGM from sulfide minerals to their elemental states. The roasted concentrate was preleached with dilute sulfuric acid to remove easily soluble gangue minerals. After pre-leaching, the concentrate was slurried with 6M HCI and leached at ambient temperature and pressure with a strong-oxidizing agent. Hydrogen peroxide, chlorine, sodium hypochlorite, nitric acid, and a persulfate salt were the oxidants investigated. The two-stage leaching scheme ex-tracted up to 97 pct of the platinum, 92 pct of the palladium, and 99 pct of the gold from the roasted concentrate. The base metals were not solubilized and reported to the residue. No attempt was made to devise a procedure to recover the copper and nickel because they comprise less than 5 pct of the value of the concentrate. Viable techniques for recovering the precious metals from the pregnant solution were sulfide precipitation, cementation with nickel, or adsorption on activated carbon.

Jan 1, 1985

This Bureau of Mines investigation addressed two primary issues of air velocity measurement in mines: the determination and use of correction factors, and the development of guidelines for the selection of a suitable site at which the measurements should be taken. Other facets of the investigation included a comparison of measurement methods and devices, and aircourse cross-sectional area measurement. The study consisted of theoretical, laboratory, and in-mine investigations. The measurement devices included in the experimental phase were vane anemometer, vortex shedding anemometer, a prototype thermoan-emometer, smoke tube, and oil of wintergreen sprayer. The measurement methods included single-point centerline, timed-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices. The study resulted in guidelines for measurement site selection that are applicable to most inmine situations. It also showed that the use of correction factors is problematic. There are many potential pit-falls and there are cogent arguments against using certain correction factors. However, generalized correction factors were developed that can be successfully applied in routine ventilation work, provided that their use is properly understood.

Jan 1, 1985

By Michael J. Beus

This Bureau of Mines report describes a field experiment involving the sinking of two test shafts to directly compare the deformational behavior of circular and rectangular shapes. Results show that the circular shape is less sensitive to geologic discontinuities and applied stress field. Also, the rectangular shape is subject to a variety of behavioral modes, including beam bending and buckling. Geologic discontinuities around circular and rectangular shapes influence displacement significantly. Simple, two-dimensional elastic finite-element modeling, simulating circular and rectangular shapes in a biaxial stress field, shows that the structural response of a shaft is largely controlled by geologic structure. Consideration of anisotropy may be required for realistic analysis of a deep shaft.

Jan 1, 1985

By S. C. Schaefer

The Bureau of Mines investigated tIle standard Gibbs energies of formation, 8Gfo, for MllF2 (manganese difluoride) and CoF2 (cobalt difluo-ride). High-temperature galvanic cells employing CaF2 (calcium diflu-oride) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1985

The objectives of this research were to examine and to laboratory performance of several brands of rigid urethane een brands, produced by 13 manufacturers, were examined. was performed in a laboratory under controlled conditions. document the foam. Eight-All testing Preliminary laboratory tests included flame spread evaluations, flame penetration, ignition temperatures, air permeability, and adhesion. Having established arbitrary cutoff values, the original 18 candidates were narrowed to 8. More specialized tests followed. The effects of water immersion and dry aging on flame spread performance and other physical properties were then examined. This Bureau of Mines report was written to provide information for those concerned with using rigid urethane foam as a sealant. Its intent is to describe the various laboratory evaluations performed and to delineate the performance of each candidate. This report neither promotes nor discourages the use of rigid urethane foams. It presents results that will enable those responsible for using or enforcing the use of rigid urethane foams in underground mines to make informed decisions.

Jan 1, 1985

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985