Search Documents

By A. D. Marcy

The Midnite Mine is an inactive, hard-rock uranium mine in Stevens County, WA. Oxidation of sulfide-containing minerals, primarily pyrite, in the ore body produces large quantities of acidic water. An interception system installed by the mining company limits the discharge of contaminated water from the mine. The U.S. Bureau of Indian Affairs (BIA) and the U.S. Bureau of Land Management (BLM) have been actively involved in planning remediation of the disturbed areas. To assist in remediation, the U.S. Bureau of Mines (USBM) initiated research to determine water quality and to define ground water flow characteristics. USBM personnel designed a monitoring network, supervised installation of sampling wells, and collected and analyzed water samples. This Report of Investigations describes interpretation of data collected between December 1989 and April 1992. The computer program WATEQ4F was used to identify aqueous species distribution and to calculate potential solid phase controls of solubility. To assist in interpretation of changes in water quality between sampling locations and to develop models describing proposed flow paths, the computer program BALANCE was used. Using output from these programs and field observations, a description of the chemistry along proposed ground water flow paths at the mine is presented.

Jan 1, 2010

By Robert C. Dyni

The use of techniques and equipment designed to pneumatically place backfill into an underground mine opening through boreholes for subsidence abatement has historically met with limited success, largely due to the inability to directly monitor the placement of the backfill in the opening. The success of a backfilling project cannot be guaranteed if it is not known whether the underground opening has been completely filled with backfill material. To overcome the inability to directly monitor backfill placement, the U.S. Bureau of Mines developed a pneumatic backfilling system that allows for direct viewing of the backfill as it is placed in an underground mine opening. This system utilizes a recently developed pneumatic nozzle coupled with an instrumentation package that allows for real-time observations and measurements of backfill placed in an underground opening through a borehole. The nozzle utilizes a high-velocity airstream to redirect backfill falling through a pipe in the borehole and directly in front of the nozzle; the airstream redirects and propels the backfill horizontally into the .mine opening at over 100 ft/s. The instrumentation package, mounted directly to the nozzle, contains a video camera, high-intensity lamps, laser-rangefinder, electronic compass, and water sensor.

Jan 1, 2010

By Thomas M. Barczak

This U.S. Bureau of Mines report examines the causes and consequences of longwall face sloughage. Theoretical relationships were developed to evaluate mechanisms that produce slough age. From these relationships, contributory factors were identified for further analysis in field efforts. A survey identified 12 mine sites with sloughage problems, and these were investigated. From these studies, it was determined that the depth of cover and mining height are the two most significant factors causing sloughage on longwall faces. Coalbed friability and cleat orientation also were found to be significant factors in promoting sloughage. It was concluded that sloughage is primarily a problem in thicker seams or seams with friable coalbeds, and that the problem is more severe as the depth of cover increases. Sloughage also was found to increase as the rate of mining decreased. Observations indicated that face slough age can increase dust generation significantly on longwall faces. Current efforts to control dust generation from longwall sloughage are described.

Jan 1, 2010

By Todd M. Ruff

Current methods of inspecting wire rope for broken wires or excessive wear include visual inspection, physical measurements of rope diameter, and electromagnetic nondestructive testing (NDT). Visual inspection and physical measurement arc the least comprehensive methods. Electromagnetic NDT enables a more thorough assessment of the condition of a wire rope, but the repeatability, accuracy, and objectivity of this method can be improved. One means of achieving this goal is to use a computer to analyze the test data and determine the condition of the wire rope, including the presence of broken wires and corrosion, and the amount of wear. An off-the-shelf data acquisition and analysis system was tested in a U.S. Bureau of Mines laboratory using a continuous loop of wire rope containing fabricated flaws. The test rope was run through a commercially available NDT instrument. The output of the instrument, normally connected to a paper strip chart recorder, was digitized and analyzed with a personal computer. These initial tests were successful in showing that the use of a computer can improve current methods of NDT waveform collection and analysis.

Jan 1, 2010

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By L. Garner McDonald

The U.S. Bureau of Mines, under contract to the U.S. Department of Energy, investigated the erosive-wear properties of seven commercial alloys with potential applications as valves for coal-conversion plants. A dry particle, jet-erosion apparatus was used to determine the wear of seven materials: 316 and 440-C stainless steels, K-68, K-701, and K-801 cemented tungsten carbides, HC-250 white cast iron, and Haynes 6B. The alumina abrasive entrained in the nitrogen gas jet had particle sizes of 27 or 50 µm, the abrasive velocities were 55 to 170 m/s, and the particle impingement angles were 15° to 90°. The maximum specific wear for ductile materials was found to occur at impingement angles of 15° to 30°, and the minimum specific wear occurred at 60° to 90°. For the brittle materials, maximum specific wear occurred at impingement angles of 50° to 85° and minimum specific wear was at the lowest angles. As the velocity and erosive particle size increased, the specific wear increased. The specific wear was related to the velocity by the power function WocAVn, where n was 1.8 to 3.9 for ductile materials and 1.8 to 3.6 for brittle materials.

Jan 1, 2010

By A. Visnapuu

The U.S. Bureau of Mines investigated the oxidation of American Iron and Steel Institute (AISI) Type 304 stainless steel (SS) during annealing in simulated combustion products from several air-CH4 fuel ratios. Atmospheres representing air-CH4 ratios of 14:1 and 18:1 contained free 02, while atmospheres representing 10:1 air-CH, ratio did not. A Cr203 layer formed on SS samples annealed in atmospheres containing free 0, while a Cr-Fe spinel layer formed in atmospheres with no free 02. The Cr203 layer was adherent and presented a protective barrier to metal diffusion, effectively limiting oxidation of the metal substrate. The Cr-Fe spinel was not protective and allowed the diffusion of Fe through the spinel to the gas-oxide interface where it was oxidized to magnetite, which spalled from the surface. This resulted in thick scale layers on samples annealed in atmospheres containing no free 02, as compared to layers formed on samples annealed in atmospheres containing free 02. These results confirmed and explained industrial operators' observations that thick, smoky (fine spalled magnetite) scales form on SS annealed in low free-02 atmospheres, while thin protective oxide layers form on sheets in atmospheres containing free 02.

Jan 1, 2010

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

By M. J. Jackson

MIGRATOM is a third-generation PC-based computer program developed by the U.S. Bureau of Mines for geophysical tomography. Like its predecessors, BOMTOM and BOMCRATR, MIGRA TOM was developed to enable users to address a variety of mining-related problems by mathematically reconstructing the distribution of physical properties in a rock mass, using measurements of travel time or amplitude of wave energy propagated through the rock mass. Examples of applications include lithologic characterization, fracture detection, fluid monitoring, stress evaluation, and blast assessment. The resolution and accuracy of tomographic reconstructions generally depend very strongly on the geometry of source and receiver locations. In many practical applications, such as cross-borehole tomography, limited coverage results in nonunique reconstructions. MIGRATOM follows the precedent of BOMTOM and BOMCRATR in allowing the user to constrain the inversion, in order to reduce the nonuniqueness problem. A new approach to application of constraints implemented in MIGRATOM is based on fuzzy logic techniques. Refraction of wave energy is modeled in MIGRATOM using an approach based on Huygens' Principle. Propagation of a continuous wavefront is modeled as a constructive interference phenomenon, which obviates the shadow-zone problem that affects conventional ray-tracing calculations. MIGRATOM has been tested with both synthetic and field data sets.

Jan 1, 2010

By Robert F. Chaiken

An absorption-desorption model of particle reactivity was employed to describe the observed relationship between two apparently diverse phenomena which have been the subject of considerable study at the U.S. Bureau of Mines: (1) coal-rock dust reflectance and (2) coal-rock dust explosibility. The model accounts for heterogeneities in particle-size and material properties; however, in the present report, only particle-size distribution is considered. A mean particle-size parameter, appropriate to the explosion extinction process, is derived, and then taken as appropriate to describing optical reflectance. The derived form-to-function relationships for the two processes, when compared with experimental data, suggest that a problem exists with previously derived theory relating optical reflectance to rock dust concentration. A reexamination of that theory leads to a new theoretical expression, changed by a factor of 2, for the variation of rock dust concentration with reflectance which is in quite good agreement with experimental results. The current work offers justification for measuring and establishing rock dust requirements for specific coal dust size distribution(s) found in the mine-distributions that undoubtedly depend on the mining method and the type of coalbed.

Jan 1, 2010

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines (USBM) and the US. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSRYs were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 1994

By Paul W. Jeran, Michael A. Trevits, William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 1@ m3/d were observed. The variability of gas production from individual holes can be attributed to several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1994

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010