Search Documents

By E. H. Denny

The presence in the Cripple Creek district, Colo., of irrespirable gas or gases, generally known to consist mainly of nitrogen and carbon dioxide, has been recognized by members of the mining industry in that region almost since underground mining was begun there; the occurrence, origin, and possible control of these gases have been discussed in several articles cited at various places in this report. Similar gases have also been studied in other metal-mining districts, as later discussed. In March, 1925, there were two fatalities from rock-strata gases in the shaft of the Index mine, near Cripple Creek. Two men repairing the bell or signal line preparatory to reopening the shaft were lowered into irrespirable gases and died. Their bodies were recovered by rescue crews from the United States Bureau of Mines and .the Portland mine, Victor, Colo. These crews found it necessary to use oxygen breathing apparatus. In October of the same year a miner was trapped on the 6 level of the Midget mine by an influx of gases that filled the shaft to a point above that where he was working. Oxygen breathing apparatus was again used by Bureau of Mines employees, who were in the vicinity, and the man was brought out in time to save his life. These two fatalities and one near fatality seemed to show that additional investigation of the gases and methods of control might be warranted. Accordingly, field and laboratory studies were begun by the authors of this report after a visit to the district by M. van Siclen, then engineer in charge, mining research division, Bureau of Mines, and after conferences with the Mine Owners' Association of Cripple Creek and with J. T. Joyce, metal-mine commissioner of the State of Colorado. The mine operators of the Cripple Creek district and the State mine commissioner's office gave whole-hearted cooperation in this work.

Jan 1, 1930

By R. Hogg

"Agglomeration processes and agglomerate characteristics are largely controlled by the forces of interaction between particles. The nature and typical magnitude of these interaction forces are evaluated relative to the external forces commonly present in agglomeration systems. The specific roles of the interaction forces in the various stages of agglomerate formation and growth and their effects on the integrity and mechanical strength of agglomerates are briefly reviewed. Because the interaction forces affect different aspects of agglomerate development in different ways, conflicting requirements can arise. Examples of such conflicts are given and used to demonstrate the importance of evaluating the effects of interaction forces etc., in the context of the overall agglomeration process and its ultimate objectives.INTRODUCTIONThe term agglomeration is generally used to refer to processes whereby discrete particles are caused, or allowed, to associate into clumps in which the individual particles retain their identity but are held together by relatively weak, usually physical forces. Various other designations are given to these processes, depending on the specific circumstances under which agglomeration occurs. The terms balling and pelletizing are often used to describe agglomeration in dry or semi-dry powders; coagulation and flocculation are used to refer to agglomeration of particles dispersed in fluids. Common to all of these cases is the fact that the formation, growth and integrity of the agglomerates depend primarily on the forces acting on and between particles. The same forces are, of course, responsible for manyaspects of the behavior of colloidal systems and their study and evaluation constitute the,basis for colloid and interface science.FORCES ACTING ON FINE PARTICLES AND AGGLOMERATES It is convenient to classify the forces acting on and between particles into two general types: external forces and interaction forces. It should he recognized, however, that a sharp distinction is not always possible.External Forces Gravity and inertial forces act on all particles and their magnitude is proportional to particle mass, i.e. they vary with the cube of particle size. Such forces are oftensignificant for large agglomerates but may be negligible for individual, fine particles.Hydrodynamic (""drag"") forces are important, for particles suspended in fluids. For very small particles, the drag force is directly proportional to size (Stokes' Law) while for very large particles or agglomerates it varies with approximately the square of size (Newton's Law). A useful procedure for estimating drag forces over a broad range of particle sizes and physical conditions has been given by Concha (1)."

Jan 1, 1989

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggest that many rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to sudden failures of rock and cemented sandfill surrounding stopes. We believe that the reduction of rock burst hazards must be based on a clear understanding of the basic mechanisms involved. The current work emphasizes the mechanical role of wall rock movement and seismicity in generating conditions that promote rock burst damage. Based on our interpretations of these mechanisms, we briefly address several hypothetical practices that could influence rock burst hazards in similar mining situations. The overall goal of this research is to advance the NIOSH mission of improving the health and safety of the nation’s workers.

By Nar S. Dala1, Xianglin Shi, Val Vallyathan

"Electron spin resonance (ESRJ and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fracture-induced, silicon-based radicals (Si· and SiO·) and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO · radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO, Na;iSeO:y ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotoxicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). From the comparison of hemolysis and ESR results it is deduced that the radicals play little or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell: membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made toward the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanisms underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1990

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By N. S. Dalal, W. Irr, X. Shi, V. Vallyathan

"Inhalation of crystalline silica is associated with a biphasic biologic response of acute cell injury and chronic pulmonary fibrosis. Dust induced cell membrane injury leading to the release of lysosomal enzymes and cell death has been implicated as the initial important biologic event triggering the fibrosis. However, it ls also possible other biologic reactions could alternatively, or in addition to these enzyme related cytotoxicity reactions, alter the normal functioning of cells. It is well known that phagocytic activation results in the production of oxygen radicals which are highly cytotoxic to cells. In healthy - lung, protection against the toxic effects of the normal balanced ·biologic reactions are provided by a number of defen1e systems including antioxidants. In disease or condition of overproduction of oxygen radicals, biochemical protection may be overwhelmed with resultant cellular injury.Our recent observations have shown that reactive oxygen radicals (ROR) are generated during grinding of crystalline silica. We hypothesized that these newly generated RORs may cause cell injury, lipid peroxidation, or even damage to macromolecules such as DHA. Biochemical aberrations caused by the inhalation of crystalline silica with ROR at occupational settings might overwhelm cellular and antioxidant defense systems of the lung leading to injury and subsequent fibrosis.To test this hypothesis, we have investigated the generation and decay of ROR produced by crystalline silica using electron spin resonance (ESR) and investigated its toxicity with conventional biologic tests at various time intervals after grinding. We also studied the decay of these newly generated RORs in buffer and the effect of antioxidants and scavengers in the abolition of cellular damages."

Jan 1, 1989

Provide mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check list for inspecting rollover protection structures (ROPS) being used in mining operations. The Problem ROPS are provided on mobile surface mining equipment to protect operators from such safety hazards as machine rollovers, falling objects, and collisions. However, the protective capability of a ROPS can be greatly reduced if it is damaged. Certain kinds of damage, such as hair- line cracks, corrosion, and loosened bolts, may occur as a result of normal machine use but may not be recognized as unsafe by untrained personnel. Therefore, the Bureau of Mmes designed a manual which can be used by mine personnel when inspecting ROPS equipment. The Manual The manual was prepared to help acquaint mine safety personnel and MSHA inspectors with typical ROPS deficiencies and their causes. It provides a systematic means for inspecting ROPS so that the identified deficiencies and their causes can be corrected. It is suggested that an inspection of the ROPS be conducted after every 1,000 h of equipment operation, or sooner if the structure has been subjected to any unusual loads which could cause damage, such as a rollover, highwall caving, or collision. The manual also details common deficiencies in the structure and attachment hardware which may affect the service life. The checklist, when used as instructed in the manual, provides a means for systematically inspecting the structure to ensure maximum protective capability and conformance with applicable Federal regulations.

Jan 1, 1986

By Deno M. Pappas, Christopher Mark, Eric R. Bauer

During 1998-99, groundfall incidents resulted in 27 fatalities and were responsible for over 70% of all deaths in U.S. underground coal mines. To obtain a better understanding of where and why these incidents occurred, a comprehensive analysis of ground fall injuries and fatalities was conducted. The first portion of the study examined various factors associated with roof and rib fall injuries and reportable roof fall noninjuries that occurred during 1995-98. The study found that the room-and-pillar mining method has twice the groundfall incident rate than the longwall method. Mine locations with high groundfall rates seem to correlate to regions where there is a higher concentration of problematic coalbeds. For example, the Illinois Basin has very high groundfall rates, which can be traced back to several key coalbeds-Kentucky No. 13, Herrin/No. 6/Kentucky No. 11, and Springfield No. 5/Kentucky No. 9. High rib fall rates were found in mines located in thick seams. Groundfall rates were found to be 30% to 40% higher during the months of July through September, possibly due to high humidity that may cause the shale mine roof to deteriorate. The second part of the study examined the root causes of failure by reviewing all groundfall fatality reports for 1996-99. Primary and secondary hazard factors were assigned to each groundfall incident. The primaryf actors resulting in these groundfall fatalities were pillar extraction, traveling under unsupported roof, skin failure, construction, longwall faces, intersections, and geologic discontinuities. Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 10, 2000

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden. i.e., >30 at (100 ft), were caused by stress concentrations and geologic strictures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions tremendously influence ground stability.

Develop a lightweight, portable device for use in mines for non-destructive testing of resin grouted roof bolt bond integrity. Approach A unique, intrinsically safe, electronic instrument has been developed that determines the holding quality of a fully grouted roof bolt by testing the integrity of the resin bond to both the bolt and to the surrounding rock. How It Works A measured pulse of energy Is sent Into the bolt by a piezoelectric transducer, and the instrument listens for reflected energy. Where the bolt is properly bonded, the energy passes from the bolt, through the resin, and out into the rock mass. Where proper bending does not exist, a portion of the energy Is reflected back along the bolt. The Instrument measures the reflected energy and compares it to the original pulse. The amount

Jan 1, 1982

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

Improve the safety of mine workers by developing a means of forecasting impending roof falls in underground mines. Approach The Bureau of Mines, through in-house and contract research, has developed the Roof Fall Warning Device. This battery-operated, portable electronic system forecasts roof falls by detecting and interpreting high-frequency rock noise, The technology has shown potential for detecting stress-related failures in a variety of underground environments. How It Works All geologic materials produce high-frequency acoustic emissions when they encounter an increase in stress. These ultrasonic frequency range events ( >20kHz) are well above the audible range of human hearing, very small in amplitude and duration, and can only be detected with sophisticated electronic equipment.

Jan 1, 1990

By l.J Prosser

from 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig. 1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig.2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91 %, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from 1990 to 1996.

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

By Craig S. Compton

The failure of the immediate roof or "roof skin" between installed primary and secundary roof supports causes hundreds of injuries and, on average one or two fatalities each year in U.S. underground coal mines. Conventional roof supports cannot cover enough roof area to adequately control these relatively small, but very dangerous rock falls. The 2006 Mine Safety and Health Administration (MSHA) accident database lists a total of 542 ground fall injuries, including 10 fatalities. An analysis of the database suggests that 434 of the injuries and three of the fatali­ties can be attributed to roof skin falls (See Figure 2). The key to controlling falls of the immediate roof or roof skin is maximizing the area of roof coverage ilnd confining these relatively small loose rocks. Roof screen offers maximum coverage of the immediate roof. Depending on the size and configuration of the screen panels, coverage of up to 100% of the roof area is possi­ble. Screen also offers a first line of defense for machine operators working in the face area by confining or deflecting small rocks that can come loose during mining or roof bolt installation. Figure 1 shows an example of the protection screen provides dur­ing bolt installation. Although the benefits of screen are well-known, mining com­panies in some areas of the U.S., mainly Northern Appalachia and the Illinois basin, are not convinced that roof screen is the best tool for dealing with roof skin control issues. The logistics of material handling, possible ergonomic injuries to workers, and the costs associated with installation are delaying the acceptance of screen as an on-cycle roof support tool. Other mines however, have concluded that installing roof screen can be cost-effective when compared to the cost of lost time accidents, training of replacement workers, or returning to already developed entries for the cleaning and rebolting process.

Jan 1, 2009

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

By R. Karl Zipf, Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non-fatal injuries to human workers. A commonly used technique is to devise an “incident prevention plan”, which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident – in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of “events of interest”. This paper introduces a novel technique – “Taxonomic Analysis”, which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984-1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.