Search Documents

By L. W. Kelly

The purpose of this circular is to show that, under the conditions prevailing in the Stony Point mine, wooden bolts were just as satisfactory as steel bolts or conventional timbering, with a reduction of approximately 80 percent in cost of material. This one fact alone is enough to justify an experiment with wood. This circular will show that production records have remained constant with both wooden and steel roof bolts. INTRODUCTION The successful use of steel roof bolts is now an accomplished fact in the coal industry, but the use of wooden bolts in place of steel is a rarity. The first experiment with wooden roof bolts was mane in 1949 in the Rio Verde mine, Norton Coal Corp., Nortonville, Ky.2/ This experiment was successful; the company obtained excellent results, but operations in the mine were suspended before enough time had elapsed to prove the value of wooden roof bolts conclusively. It is obvious that, if wooden roof bolts could be used in place of steel bolts or conventional timbering-methods, every mine operator would use word, as the cost is only a fraction of the other two methods. The Stony Point experience has proved conclusively that, under certain conditions and with a certain type of roof, wooden roof bolts can be used successfully.

Jan 1, 1952

By Wilbur A. Haley

The demand on the nation's reserves of high-quality coals suitable for metallurgical purposes is resulting in the rapid depletion of some of the thicker coal beds. These beds are thick enough to permit the use of modern mechanized mining equipment. Many of the thin beds are not being mined at present. In limited areas where the coal is less than 36 inches thick some beds are mined by various conveyor methods. Usually, the room-and-pillar system or some modification of it is used, and often no attempt is made to extract pillars. Consequently, an appreciable quantity of a valuable resource is lost. Many steel companies and coal operators consider reserves of low-and medium-volatile coking coals to be critical, especially in areas where the thin beds are not being mined by modern mining methods. To improve recovery and to promote more-extensive mining in thin beds, methods and devices that are new to American coal mining but applicable to the mining of thin coal beds should be tried. As one of the functions of the Bituminous Coal Mining Section of the Bureau of Mines is to promote improved mining practices and efficiency in the interest of conservation, research in that line is necessary. In 1945 coal planers were observed in operation in Germany by a Bureau engineer member of Solid Fuels Mission to Germany. Planer designs and history of early developments and operations were published. In 1949 an improved planer was again studied by Bureau engineers, and its adaptability to certain conditions in the United States, especially thin beds of friable coal, was considered practicable. After the war the planer was improved, in design and for several years has been operating successfully in the Ruhr. Because of the conviction that the device would be successful, both from the standpoint of conservation and operational prodl1ctivity, under certain conditions in the United States, the Bureau of Mines, through the Bituminous Coal Mining Section, entered into a cooperative agreement with the Coal Division of Eastern Gas & Fuel Associates and Mining Progress, Inc. The purpose of the agreement was to conduct an experiment in modified longwall mining, using a new-type German-built coal plow or planer, known as the Loebbe Habel, supplied by Mining Progress, Inc. The experiment was made to determine if this type of mining equipment operated on a longwall face could be adapted to some of the thinner American coal beds. Such an experiment also would afford many opportunities to study the possibilities and principles of this type of equipment as well as the many factors involved in the mechanical mining of a longwall face.

Jan 1, 1952

By Irving Hartmann

In recent years various modifications in the methods of blasting have been tried as a means of increasing the production of cod and of reducing mining costs. Following an investigation by the Bureau or Mines, authorization was granted to increase the charger limit for permissible explosives par shot hole from 1.5 to 3 pounds under contain conditions; this greatly facilitates the blasting of coal in some cool fields the practice has gradually evolved of simultaneously charging several shot holes in a face and then firing the charges singly without inspecting for gas after each blast. This practice is disapproved by the Bureau of Mines. In other coal mines the explosive chews in several adjacent shot holes are fired simultaneously. This form of shooting is claimed to increase the rate of production, generate smaller volumes of noxious gases, promote the health and safety of workers by eliminating the need of inspection of the face after each charge is fired, produce less float dust, and require less explosive than single shooting. However, simultaneous blasting may have a more harmful effect on the immediate roof strata; in some instances it leads to wedging of the broken coal, thereby making the coal more difficult to load out; it makes misfired shots more difficult to detect and possibly increases the chances of misfires. This lacy be duo to variations in the characteristics of detonators, because of more stringent requirements for adequate firing current, to the need for better electrical connections in the shot-firing circuit, and partly to the inadequacy of present permissible multiple blasting devices.

Jan 1, 1952

By H. L. Burmeister

These properties were examined by a Bureau of Mines engineer in 1949. During 1950, these mines were studied by the Bureau to determine the possibility of increasing the production and augmenting the supply of fluorspar. As a result of this study, it was decided to core-drill the Knox-Yingling vein to test the continuation of fluorspar to a greater depth than that reached by mine workings. It also was desired to relate the present deposit with the Rosiclare formation. Development work by the Bureau of Mines was performed from February to May inclusive in 1951. Four diamond-drill holes aggregating 2,733 feet were drilled in the hanging wall of the vein.

Jan 1, 1952

By R. W. Huber

While conducting an investigation on electrolytic reduction of magnesium oxide in 1943, it became necessary to obtain accurate data on the conductivity and density of various mixtures of fused chlorides. AZ the required information was not available in the technical literature, or there were inconsistencies in the data from several investigators, an independent study was made at the Bureau of. Mines laboratory at Salt Lake City on the conductivity and density of the molten chlorides MgCl2, CaCl2, BaCl2, KCl, and NaCl and the binary mixtures of MgCl2 with the other four chlorides. Studies were also made on the binary system KCl-CaCl2 and on certain portions of several ternary systems. Measurements covered a temperature range from the melting point to 1,000° C. The results of this study were reported in an intra-Bureau report prepared early in 1944. Since then the Bureau of Mines has received several requests for data on fused chlorides; the results of the previous study, therefore, are being published to make the data available.

Jan 1, 1952

By W. A. Calhoun

A method for treating high-iron Arkansas bauxites for recovering both abrasive and metal-grade bauxite has been developed by the Bureau of Mines. Present practice usually produces a reject containing appreciable quantities of metal-grade bauxite; however, the processing renders the alumina in the reject unsuitable for the Bayer extraction treatment. Thus the Arkansas abrasive bauxite industry has, in the past, produced little or no metal-grade bauxite. The present investigation was made to determine the possibilities of batter utilization of those particular bauxites through recovery of the wasted metal-grade portion. The large expansion of aluminum-production facilities planned for 1951-53 makes recovery of metal-grade bauxite from presently treated abrasive and marginal abrasive ores en especially timely objective and a welcome addition to our aluminum potential. The quality of the Arkansas bauxites and the inherently associated titania content have made this material particularly attractive to the abrasives industry. however, the gradual depletion of natural abrasive-grade bauxite reserves in this area, the comparative scarcity of high-grade ore, and the difficulty of maintaining adequate reserves have necessitated blending different grades of bauxite calculated to meet specifications. Production of abrasive-grade bauxite from tile, high-iron reserves 13 becoming, increasingly necessary. In one commercial operation, producing abrasive-grade from ores averaging slightly less than 10 percent Fe2O3, approximately 2.7 tons of ore are required to produce 1 ton of abrasive-grade bauxite. The reserves of ore of this grade, however, have been considered inadequate for a long-range production, and ultimately ores averaging 12 to 15 percent Fe2O3 will have to be treated to moot the continued demands of the abrasive industry.

Jan 1, 1952

By James A. West

The Quapaw pool is one of the smaller pools in an extensive area of Bartlesville-sand production in the eastern part of Osage County, Okla. (fig. 1). Most of the fields in this area were discovered from 1906 to 1916 and were developed and operated similarly. The Quapaw pool is representative of the area, and much of the developed in studying this pool is applicable to the other reservoirs. This petroleum-engineering study of the Quapaw pool was conducted to provide reservoir data that may aid in more widespread application of the intensive secondary-recovery production methods that have been employed with excellent results in the Bartlesville-sand fields of nearby Washington, Nowata, and Rogers Counties. This study is particularly appropriate because of the intense interest in Osage County fields as areas suitable for water flooding. Water flooding was introduced first into Oklahoma during 1931 in Rogers County, and activity was concentrated in the shallow Bartlesville-sand fields of and Nowata Counties for many years. Although water-flooding projects are now operating throughout the State, the intense activity of the Nowata-Rogers Counties area spread to adjoining counties only during the past few years. Since 1948 the rate of oil production in Washington County (between Nowata and Osage Counties) has increased by 260 percent as a result of water flooding. Currently, leases in eastern Osage County are sought eagerly by water-flood operators, and during the past 2 years the Osage Indian Agency has issued nine permits for water-flooding projects in eastern Osage County. Water-flooding operations are in progress on several projects. Although large oil reserves in eastern Osage County should, be recoverable by water flooding, development and operation of projects will be more expensive than projects in the shallower producing areas to the east. In addition, the Osage County reservoirs appear to be more complex and somewhat more difficult to water-flood successfully. It is hoped that this study will contribute to better understanding of the Quapaw reservoir and, in a general way, to the many similar reservoirs in eastern Osage County.

Jan 1, 1952

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By William L. Crentz

Early in the nineteenth century, coal from Clearfield County entered the eastern commercial market. Ashley reports that coal was moved down the Susquehanna River by ark from Clearfield to Columbia, a distance of 260 miles, as early as 18o4. Around 1850, the famous Moshannon or Lower Freeport bed was discovered. Several years later the Moshannon Basin was developed extensively, and the coal from this area soon acquired an enviable reputation as a high-quality industrial fuel. Today much of the original Moshannon Basin coal is worked out, and the Lower Kittanning bed has replaced the Lower Freeport bed as the principal source of production in southeast Clearfield County. With depletion of the thick underground deposits, the importance 'of Clearfield County as a coal Producer would have diminished rapidly, if it had not been for strip mining the thinner beds. About 60 percent of the coal produced in the county is strip-mined, and the trend toward this mining method is expected to continue as the older underground operations are exhausted. Many strip mines are working in beds that are too thin to be recovered economically by any other method.

Jan 1, 1952

By A. T. Coumbe

The first national survey covering sales of fuel oil by States and principal uses was made in 1926 by E. B. Swanson of the Bureau of Mines (then under the U. S. Department of Commerce) under a cooperative agreement with the American Petroleum Institute. This annual study, covering the market for fuel oil, was made through 1930 with the financial help of the institute bat has since been continued by the Bureau up to the present time. The scope and coverage of the survey have gradually changed over the years as new uses for fuel oil have been found and new products have come into importance resulting in market expansion. Range oil (No. 1 fuel oil or kerosine) came into use for cooking and space-heating daring the depression era in New England, and it was first reported as a total in the 1931 survey. In 1934 the sales were compiled on a State basis. State totals for distillate fuel oil, Diesel fuel, and residual fuel-oil sales were first shown for 1934 and by principal uses and States in 1937. Kerosine deliveries by States and main uses were also released for the first time in 1937.

Jan 1, 1952

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1952

By Jr. Sillers

To prove to .the satisfaction of all concerned that electrolytic manganese from our low-grade domestic ores could be substituted satisfactorily for ferro-manganese made from high-grade foreign fires, an extensive series of tests was conducted in cooperation with industry, in which electrolytic manganese pro-duced by, the Bureau of Mines at its Boulder City, Nev., Station was substituted for the ordinary ferro grades in the production of ferrous and nonferrous metals and alloys and welding-rod coatings. Over 1,200,000 pounds of manganese was given out for this purpose. The objectives of the tests were accomplished, and for some purposes electrolytic manganese was shown to be superior to other grades because of its high purity. The only serious objection that can be raised against electrolytic manganese is its price, which puts it out of reach for most purposes. Even if the price were to be lowered to a point where it would be in line with ferro grades, it is questionable whether electrolytic manganese from domestic ores could supply more than a small part of the needs of American industry because of the large volume of domestic ore that would have to be processed to supply a satisfactory feed for the electrolytic process. Thus, although electrolytic manganese is highly desirable from a metallurgical standpoint, it could not be expected to substitute for more than a fraction of our domestic manganese requirements.

Jan 1, 1952

By S. H. Ash

THE BARRIER-PILLAR SYSTEM in the Lackawanna Basin consists of 93 barrier pillars between Archbald and Taylor, Pa. These pillars affect 48 mines, have a total length of 87 miles, and confine 21 underground pools, which contain more than 10 billion gallons of water. From an investigation of size, position, and condition of the barrier pillars, it is apparent that those concerned are uncertain, not only as to the method by which the sizes of the barrier pillars were determined but also as to the stability of those that may be expected to act as dams. Where a barrier pillar must act as a dam, its failure may result in loss of life, the mine, or both; it would be far better had it not existed and thereby given a false sense of security.

Jan 1, 1952

By H. J. Kelly

[This investigation of the refractory properties of seven Pacific Northwest chrome ores and concentrates has shown that five of the ores and one of the concentrates are suitable for making refractories and that all may be used in combination with high-grade chromite. The specific objectives of the investigation were to determine the inherent physic al and chemical characteristics, to shapes using each of the chrome ores and concentrates, to compare the refractory qualities of the laboratory-prepared with commercial chrome refractories. As far as possible, standard tests were used as criteria.]

Jan 1, 1952

By Forrest T. Moyer

THE injury data and experience in this bulletin are presented in three general sections. The first section contains general and detailed data relating to 1948 injury experience in bituminous-coal and Pennsylvania anthracite mines, separately and combined into totals for all coal mines. The related employment, worktime, production, and productivity data are given in each breakdown of the statistical data. Tables 1 through 22 constitute a subsection and present statistics on number of injuries, frequency and severity rates, average severity, detailed and major causes of injuries, injury records of the coal-producing States, distribution of injuries by part of body, and distribution of injuries by days of disability. Tables 23 through 45, the second subsection, present injury experience in bituminous-coal mines by various selected factors of physical or operating conditions that ma contribute to the occurrence of injuries. The degree of mechanical loading, productivity, size of mine by number of men working and by tonnage mined, thickness of bed, length of shift, number of shifts, type of cap lamps, rating of mine as gassy or nongassy, type of ventilation, and combinations of these factors influencing mine safety are presented in this group of tables. Similar data on Pennsylvania anthracite mines are listed in tables 46 through 63, which comprise the third subsection. The second section of the report contains the generalized annual injury records of bituminous-coal, Pennsylvania anthracite, and all coal mines from the earliest available data through 1948. Tables 64 through 97 list the number of fatal and nonfatal injuries, injury rates, and causes of injuries on an industry basis, the long-term injury records of each coal-producing State, and the related employment, worktime, and production data.

Jan 1, 1952

By H. Kenworthy

The objective of this research was to develop methods and determine conditions under which metallic sulfides with lower boiling points than sphalerite may be removed from zinc sulfide concentrates by volatilization. A higher percentage of extraction of lead, cadmium, and germanium than is common in current practice was sought. The investigation, conducted by the Metallurgical Branch of the Minerals Technology Division, Region VI, showed that, under proper conditions, it is possible to remove over 90 percent of the lead, cadmium and germanium as an enriched sublimate. The uses of lead, and cadmium to a lesser extent, are well-known. Although germanium was discovered in 1886 by C. Winkler, commercial use has been achieved only in recent years. The amount consumed per manufacturer unit is so small that the price of germanium may still be quoted by the gram. The electronic industries have been the chief consumer of this semiconductor. Germanium is sold largely to the fabricator as a dioxide for reduction to metal and subsequent processing into wafers for use in diode and triode electronic tubes. Extensive research at Purdue University during World War II led to the first practical use of germanium.

Jan 1, 1952

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By Albert L. Toenges

ALMOST all of the coal used for metallurgical purposes west of the Continental Divide is ruined from the Lower Sunnyside bed in Carbon County, Utah. Coke produced from Lower Sunnyside coal and used in western steel plants is weaker structurally than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality than the coal produced from the Sunnyside bed. Early in the war, the Bureau of Mines undertook an intensive investigation of western coals to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed and (b) develop, if possible, reserves of coal with coking qualities superior to Lower Sunnyside coal. Results of investigations in the Kemmerer district, Wyoming,9 and in the Minnesota Creek area, Gunnison County, Colo.,10 have been published.

Jan 1, 1952

By S. M. Runke

[The coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, end metallurgists. These studies have amassed a rather astounding array of published and unpublished information. Correlation of geological studies between individual pegmatites, as well as between major districts, has brought fort come semblance of order to the knowledge of the structure and mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain pegmatites and pegmatitic zones into several grouts of associated minerals, based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or trouping of minerals, with the methods that have been developed for recovering certain of these minerals, possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by u single integrated process.]

Jan 1, 1952

By Albert L. Toenges

(1) The Castleman Basin was investigated by diamond drilling, engineering examination, and geologic study. Agreements permitting investigation of about 14,700 acres of land were entered into with 79 landowners. Eleven beds of coal between the horizons of the Harlem and Mercer beds were penetrated in drilling. These beds from top downward are: Harlem, Upper Bakerstown, Lower Bakerstown, Brush Creek, Upper Freeport Rider, Upper Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Mount Savage, and Mercer. The total estimated reserves of coal (measured, indicated, and inferred), 14 inches or more thick, in six beds follow: [Coal bed: Etimated reserves, tons Harlem _______________________ 23,430,000 Lower Bakerstown _______________ 44, 688, 000 Brush Creek ____________________ 23, 694, 000 Upper Freeport __________________57, 731, 000 Upper Kittanning ________________ 40, 450, 000 Middle Kittanning ______________42,276,000 Total________________________ 232,269,000]

Jan 1, 1952