Search Documents

By Neil B. Young

Carbonate minerals constitute a major fraction of the oil shale in Colorado's Green River Formation. Quantification of carbonate minerals is important for the characterization of oil shale, particularly because of their thermal activity in production of oil from shale. The carbonate minerals found in this oil shale are nahcolite (NaHCO3), dawsonite [NaA1(OH)2CO3], dolomite [(Mg1-xFx)Ca(CO3)2], calcite (CaCO3), and ferroan [(Mg1-xFex)CO3]. Although carbonate minerals can be removed by acid extraction from the balance of the oil shale, direct determination of carbonate minerals is complicated by the occurrence of the same cations in more than one mineral. A method for assigning the acid-soluble cations to the individual carbonate minerals was developed from two assumptions based on oil shale geochemistry: (1) Calcite and ferroan do not occur together, and (2) the ratio of iron and magnesium is the same in dolomite and ferroan. These assumptions were tested by the Bureau of Mines by applying the technique for assigning cations to 219 samples from the saline section of the formation. The reported carbonate mineral amounts were compared statistically with X-ray diffraction peak heights, verifying the cation assignment method.

Jan 1, 1975

By F. S. Karn

Measurements were made of the flow of helium, methane, ethane, butane, and toluene through thin disks of coal. All measurements were made on a dense layer in the Pittsburgh seam identified as attritus. Flow increased with pressure differential and temperature. At room temperature and a pressure differential of 1 atmosphere flow rates along the bedding plane of Pittsburgh seam coal were helium 881 X 10-10 cm2 sec-1, methane 1.2 X 10 -10 cm2 sec-1, ethane 0.54 X 10-10 cm 2 sec-1, n-butane 0.35 X 10-10 cm2sec-1, and toluene 3.8 X 10-10 cm2sec-1. Flow rates were 50 percent lower across the bedding plane of the coal than along the bedding plane. Activation energies were 3.9 kcal mole-1 for helium and 13.6 kcal mole-1 for methane, with diffusion measured either along or across the bedding plane.

Jan 1, 1970

1. Mining to prevent and control underground acid formation should begin with education imparted through: (A) Course work at mining schools to teach prospective engineers. (B) Training of engineers presently employed in the mining industry through appropriate mining extension courses. 2. Considerable need exists to devote more attention to: (A) Hydrogeologic studies of mining areas to enhance the planning of new mines and the abatement program of existing mines. (B) Additional research to explore methods of dewatering the strata associated with mining areas. (C) Further effort to develop sealants for preventing contact between water or oxygen and the acid producing material associated with the coal seam.

Jan 1, 1970

By Kyei-Sing Kwong

The U.S. Bureau of Mines investigated the synthesis of advanced ceramics (SiC+AlN, SiAlON, SiC+A1203, and Si3N4+AlN) from natural clays (kaolin, halloysite, or montmorillonite) by an intercalation and heat treatment method. This process includes the steps of refining a clay, intercalating organic chemicals into its layered structure, drying the intercalated mixture, firing the treated structure at certain temperature ranges in controlled atmospheres to form desired compounds, and grinding the loosely agglomerated structure. Focus of this research is to economically process advanced ceramic structures from abundant natural resources. The advanced ceramic phases produced in this simple treatment are homogeneously distributed at the nanostructure level, and may potentially lead to cost effective manufacturing processes. The intercalation of clay was confirmed by X-ray and BET analyses. The evolution of chemical compositions during carbonization reactions and carbothermal reduction was investigated. The characteristics of refined clays and synthesized powders were studied. Advanced ceramic composites/solid solution have been produced from intercalated clays, without the presence of other compounds.

Jan 1, 2010

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By Wilson Blake

Rock preconditioning in advance of mining was shown to be an effective means of rock-burst control based on the results of a field demonstration carried out on the 7700 level of the Hecla Mining Company's Star mine. Mining through the preconditioned zone was characterized by greatly reduced rates of released seismic energy and no bumping or rock bursting occurred within the preconditioned zone. Mining above the preconditioned zone was characterized by greatly increased rates of released seismic energy and rock bursting, particularly where the vein became very narrow in waste zones. This increased incidence of rock bursting points out the need for stope preconditioning to be carried out on an entire stope block basis. The data obtained from the monitoring of the mining above the preconditioned zone on the 7700 level will be extremely useful in evaluating any future stope block preconditioning experiments on the lower levels or the Star mine.

Jan 1, 1980

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

The extremely cold weather and heavy snowstorms of January and February in northeastern Pennsylvania--with frozen mining equipment, diminished preparation and lack of railroad cars--severely hampered the production and distribution of anthracite. As a result, the previous estimates for the 2 months have been revised. On March 1, 1977, at the Porter Tunnel of the Kocher Coal Company at Tower City, Pa., an underground flash flood, which apparently broke through the wall of an adjoining abandoned shaft, swept through the mine. As of March 9, 1977, four miners were reported killed, three injured, and five trapped in the wreckage. The Kocher Coal Company began operations at the Porter Tunnel in 1968 and has had no fatalities until this current tragedy. The mine employs 20 persons on the surface and 115 miners underground, producing 750 tons of coal per day. Of the 109 underground mining operations in the anthracite region, this is the one remaining large mine that employs over 100 men.

Jan 1, 1977

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975

By Frank E. Cash, Max S. Peterson

"INTRODUCTION Falls of ground cause the greatest number of accidents at underground metal mines. Statistics compiled by the Federal Bureau of Mines show that during a 13 - year period ended in 1943, falls of ground caused 35 percent of the fatalities and 16.8 percent of the nonfatal injuries at underground metal mines in the United States. 4/ Expressed on a basis of a million man-hours worked, the frequency rate was 0.355 for fatalities and 11.76 for nonfatal injuries. Although some progress has boon made in preventing rock-fall accidents over a 30- or 40-year period, the problem is still a major one requiring the diligent efforts of management and employees.In the Lake Superior district: where organized safety programs have been in effect for more than 30 years, the record is more favorable. Statistics compiled by the Lake Superior Mining Section of the National Safety Council reveal that over a 6-year period ended in 1945 the frequency rate of fatalities per million man-hours was 0.277, and the rate for nonfatal injuries was 2.38 from falls of ground.Although the above-given statistics do not cover equal or concurrent periods, the improvement in accident experience in the Lake Superior district over the national average, is obvious. This improvement is due to more effective methods of ground support or more rigid enforcement of the use of known methods.It is hoped that the following information about ground-support practices in the Lake Superior district will assist operators of other mines in their efforts to reduce accidents from falls of ground."

May 1, 1948

By Robert C. Johnson

Water-swelling fluormicas and fluormontmorillonoids were synthesized and described. They were found predominantly in the system Mg0 - MgF2 - Si02, with varying amounts of Li+ or Na+, Some water-swelling synthetic minerals were prepared with only strontium or lead in the twelvefold position, Water- swelling compounds containing either K+ or Ba+ were not found. The synthesized water-swelling products were shown by electron microscopy, X-ray diffraction, and chemical analysis to be typically two-silica-layer, platy compounds, Except for the complete substitution of fluoride for hydroxyl, the compounds were similar to the natural micas or montmorillonites. The stability and properties of the compounds were further established by electrodialysis, by differential thermal analysis, and by anion and cation exchange methods. Fluoride in the interlayer positions was nonexchangeable except through decomposition of the product. Exchanging the sodium or the lithium of the synthetic fluormicas or fluormontmorillonoids with potassium ion, particularly those derived from KOH provided a product from which a completely inorganic paper of extraordinary flexibility was fabricated. This paper had excellent mechanical and electrical properties except for water adsorption and a high power factor. Neither of these problems was solved during this investigation. However, papers with dielectric strength from 1,500 to 5,000 volts per mil were readily fabricated, particularly from the lithium containing fluormicas or fluormontmorill onoids.

Jan 1, 1963

By Thomas Fraser

The Convertol process, recently developed in western Germany, is a new method of cleaning and dewatering coal-washery slurries. It is a modified bulk-oil process, in which a very small quantity of heavy oil is dispersed over the surfaces of the coal particles, followed by a screen centrifuge operation in which the water and dirt (clay, shale, and pyrite particles) are thrown out through the screen perforations and the clean coal particles are retained on the screen and discharged as a dewatered, clean coal product of 8- to l0-percent surface moisture. It is reported, also, that the process oil, all of which is retained in the clean-coal product, adds to the coking power of the coal and facilitates the production of briquets, reducing the proportions of binding material required.

Jan 1, 1953

By S. D. Hill

To help insure the continued viability of the minerals and materials sector of the U.S. economy, the Bureau of Mines is conducting research and disseminating technology that will result in more efficient minerals extraction. As part of this effort, a process is being investigated that involves an aqueous chlorine-oxygen leaching procedure to treat complex sulfide concentrates to produce ZnCl2. Subsequent fused-salt electrolysis of the ZnCI2 produces high-purity zinc metal. Previous reports described preliminary, small-scale research on the chlorine-oxygen leaching system and fused-salt electrolysis of ZnCl2. This report discusses the details of design, construction, and longterm, continuous operation of both monopolar and bipolar fused-salt cells. The effects of temperature, electrode gap, current density, electrolyte composition, and electrode configuration on current efficiency and energy consumption were determined for a ZnCl2-KC1-NaCl electrolyte system. Zinc metal was produced at the rate of about 50 lb/day in a monopolar cell which was operated continuously for 60 days with current efficiencies from 85.8 to 98.6 pct and an average power consumption of 2.1 kwhr/lb. Bipolar cells with several different electrode configurations were operated for 90 days. A current efficiency of about 70 pct and power consumption of about 1.7 kwhr/lb of zinc were achieved using a three-electrode-pair, bipolar assembly with a chlorine gas lift pump to circulate electrolyte.

Jan 1, 1981

By A. E. Sands

The Bureau of Mines, S. Department of the Interior) at, its Morgantown., W. Va., station, operating under a cooperative agreement with West Virginia University, is conducting research and development work on the problem of producing synthesis gas from coal. An important part of this work is the study of the gas purification necessary to meet the rigorous standards required to render the gas suitable for use in the Fischer-Tropsch synthesis of liquid fuels. One of the most detrimental impurities is sulfur in all forms, the maximum amount that can be tolerated being one-tenth of a grain per hundred cubic feet. Concentrations as low as this require the use of precise analytical methods to evaluate the performance of processes used for removing sulfur. At the same time the analytical methods should be rapid in order to reveal the failure of purification before damage to the expensive synthesis catalyst results. Although sulfur in unpurified gas is generally present as hydrogen sulfide and as organic sulfur compounds, the latter may be converted to hydrogen sulfide for analytical purposes. Thus a suitable method for the determination of traces of hydrogen sulfide may also be used for the determination of organic sulfur.

Jan 1, 1949

Bahrain's oil revenue increased from $337 million2 in 1916 to $378 million in 1977. Despite the increase in value, petroleum receipts made up only 584 of all Government income in 1877, compared with 74% in 1976 and 83% in 1975. Bahrain became an oil producer in 1932 with the discovery of the Awali oilfield, and since that time, the Awali oilfield has produced over 600 million barrels of crude oil. Awali production in 1977 was 21.2 million barrels. Bahrain shares the revenue from the Abu Safah oilfield, located in the Persian Gulf north of Bahrain, equally with Saudi Arabia. Revenue from the Abu Safah oilfield was approximately $179 million or 47% of oil revenues in 1977. Output from the Abu Safah oilfield was 48 million barrels, an increase of nearly 30% over 1976 output. The Bahrain Petroleum Company (BAPCO). the nation's only oil-producing company, was owned 40% by California Texas Oil Corp. (CALTEX and 60% by the Govern¬ment. The Government established Bahrain National Oil Co. (BANOCO) in 1976 to administer the Government's share of BAPCO, oversee exploration concessions, and manage domestic marketing of petroleum products. The Government announced its intention to acquire 100% control of crude oil and natural gas production. CALTEX was to retain complete control of the 250,000-barrel-per-day oil refinery near Sitrah.

Jan 1, 1981

By R. S. DeCesare

Operation of the Bureau of Mines raw refuse continuous separation pilot plant is described, including modifications made to plant equipment for improved performance. Products recovered from refuse, many of which have been evaluated by other laboratories and private firms, are discussed. Sampling procedures used in the pilot plant and detailed data obtained from processing refuse from 13 municipalities are presented in appendixes. Fuel evaluations made on combustible fractions of refuse from the various municipalities are also presented. Information and data obtained at the pilot plant have been used to assist many municipalities in solving their urban refuse problems.

Jan 1, 1980

By Berk. A. A.

"INTRODUCTION Corrosion of sections of piping used in steam-heating systems is frequently regarded as unavoidable, and periodic replacement is provided. Surfaces exposed to newly condensed steam appear to be especially vulnerable to attack. As an added nuisance, solid products of the corrosion tend to accumulate, plugging return lines.The trouble is ascribed in the main to carbon dioxide and oxygen 3/ 4 / 5/ 6/ dissolved in the condensate. When oxygen is the principal factor, the corrosion usually is characterized by pitting. Carbon dioxide tend3 to cause an acidic condensate which dissolves the metal more uniformly and produces the familiar failure at threaded areas where the piping is relatively thin, and where high stress may tend to acceletate the attack. Carbon dioxide enters the system with the feedwater, generally in a combined form such as carbonates and bicarbonates. Oxygen enters both with the raw feedwater-and as air leaking into lines under partial vacuum. The larger central-heating plants have sought to reduce corrosion by eliminating these gases as much as possible. A smaller plant ordinarily lacks the equipment and technical supervision required for this purpose."

Jun 1, 1944

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998

Commodities statistics and other information are available through the following three systems: Internet Access: To access the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, environmental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By Gary E. Sherman

Preliminary economic mining feasibility studies were conducted by the Bureau of Mines to estimate mining costs in the Juneau gold belt area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of two mineral deposit types: (1.) Berners Bay vein gold deposits, and (2.) stockwork gold deposits containing gold, silver, and lead. Cost estimates were developed using the Bureau of Mines Cost Estimating System (CES). Discounted cash flow return on investment (DeFROI) was calculated using the Bureau's MINSIM computer program. Underground mining of a Berners Bay vein gold deposit was found to be economic (15 pct DCFROI) at a recoverable metal value of $353.67/mt for a 100 mtpd shrinkage stoping mine with a 10 yr mine life, $324.76/mt for a 20 yr mine life, $138.63/mt for a 500 mtpd longhole stoping mine with a 10 yr mine 1 ffe, and $127.50/mt for a 20 yr mine life. Block caving mining of a large stockwork gold deposit was found to be economic at a recoverable metal value of $15.28/mt for a 18,000 mtpd mine with a 20 yr mine life.

Jan 1, 2011